Order this document by MPX7200/D SEMICONDUCTOR TECHNICAL DATA ! ! # #$&'$ " #!%& $& "! $%%'$ !%"$% The new MPX7200 series pressure sensor incorporates all the innovative features of Motorola’s MPX2000 series family including the patented, single piezoresistive strain gauge (X–ducer) and on–chip temperature compensation and calibration. In addition, the MPX7200 series has a high input impedance of typically 10 kΩ for those portable, low power and battery–operated applications. This device is suitable for those systems in which users must have a dependable, accurate pressure sensor that will not consume significant power. The MPX7200 series device is a logical and economical choice for applications such as portable medical instrumentation, remote sensing systems with 4 – 20 mAmp transmission and field barometers/altimeters. Motorola Preferred Device 0 to 200 kPa (0 to 29 psi) 40 mV FULL SCALE SPAN (TYPICAL) Features • Temperature Compensated Over 0°C to +85°C • Unique Silicon Shear Stress Strain Gauge • Easy to Use Chip Carrier Package Options • Available in Absolute, Differential and Gauge Configurations • Ratiometric to Supply Voltage • ± 0.25% Linearity (MPX7200D) BASIC CHIP CARRIER ELEMENT CASE 344–15, STYLE 1 Application Examples • Portable Medical Instrumentation • Field Altimeters • Field Barometers Figure 1 illustrates a schematic of the internal circuitry on the stand–alone pressure sensor chip. DIFFERENTIAL PORT OPTION CASE 344C–01, STYLE 1 VS 3 THIN FILM TEMPERATURE COMPENSATION AND CALIBRATION CIRCUITRY HIGH Zin X–ducer SENSING ELEMENT NOTE: Pin 1 is the notched pin. 2 4 Vout+ Vout– PIN NUMBER 1 Gnd 3 VS 2 +Vout 4 –Vout 1 GND Figure 1. Temperature Compensated Pressure Sensor Schematic VOLTAGE OUTPUT versus APPLIED DIFFERENTIAL PRESSURE The differential voltage output of the X–ducer is directly proportional to the differential pressure applied. The absolute sensor has a built–in reference vacuum. The output voltage will decrease as vacuum, relative to ambient, is drawn on the pressure (P1) side. The output voltage of the differential or gauge sensor increases with increasing pressure applied to the pressure (P1) side relative to the vacuum (P2) side. Similarly, output voltage increases as increasing vacuum is applied to the vacuum (P2) side relative to the pressure (P1) side. Preferred devices are Motorola recommended choices for future use and best overall value. Senseon and X–ducer are trademarks of Motorola, Inc. REV 3 Motorola Sensor Device Data Motorola, Inc. 1997 1 MAXIMUM RATINGS Rating Overpressure(8) (P1 > P2) Burst Pressure(8) (P1 > P2) Symbol Storage Temperature Operating Temperature Value Unit Pmax 400 kPa Pburst 2000 kPa Tstg – 40 to +125 °C TA – 40 to +125 °C OPERATING CHARACTERISTICS (VS = 10 Vdc, TA = 25°C unless otherwise noted, P1 > P2) Symbol Min Typ Max Unit Pressure Range(1) POP 0 — 200 kPa Supply Voltage(2) VS — 10 16 Vdc Supply Current Io — 1.0 — mAdc VFSS 38.5 40 41.5 mV Voff –1.0 – 2.0 — — 1.0 2.0 mV ∆V/∆P — 0.2 — mV/kPa — — – 0.25 – 1.0 — — 0.25 1.0 %VFSS Pressure Hysteresis(5) (0 to 200 kPa) — — ± 0.1 — %VFSS Temperature Hysteresis(5) (– 40°C to +125°C) — — ± 0.5 — %VFSS TCVFSS –1.0 — 1.0 %VFSS TCVoff –1.0 — 1.0 mV Characteristic Full Scale Span(3) MPX7200A, MPX7200D Offset(4) MPX7200D MPX7200A Sensitivity Linearity(5) MPX7200D MPX7200A Temperature Effect on Full Scale Span(5) Temperature Effect on Offset(5) Zin 5000 — 15,000 Ω Output Impedance Zout 2500 — 6000 Ω Response Time(6) tR — 1.0 — ms Warm–Up — — 20 — ms Offset Stability(9) — — ± 0.5 — %VFSS Symbol Min Typ Max Unit Weight (Basic Element Case 344–15) — — 2.0 — Grams Common Mode Line Pressure(7) — — — 690 kPa Input Impedance MECHANICAL CHARACTERISTICS Characteristic NOTES: 1. 1.0 kPa (kiloPascal) equals 0.145 psi. 2. Device is ratiometric within this specified excitation range. Operating the device above the specified excitation range may induce additional error due to device self–heating. 3. Full Scale Span (VFSS) is defined as the algebraic difference between the output voltage at full rated pressure and the output voltage at the minimum rated pressure. 4. Offset (Voff) is defined as the output voltage at the minimum rated pressure. 5. Accuracy (error budget) consists of the following: • Linearity: Output deviation from a straight line relationship with pressure, using end point method, over the specified pressure range. • Temperature Hysteresis: Output deviation at any temperature within the operating temperature range, after the temperature is cycled to and from the minimum or maximum operating temperature points, with zero differential pressure applied. • Pressure Hysteresis: Output deviation at any pressure within the specified range, when this pressure is cycled to and from the minimum or maximum rated pressure, at 25°C. • TcSpan: Output deviation at full rated pressure over the temperature range of 0 to 85°C, relative to 25°C. • TcOffset: Output deviation with minimum rated pressure applied, over the temperature range of 0 to 85°C, relative to 25°C. 6. Response Time is defined as the time for the incremental change in the output to go from 10% to 90% of its final value when subjected to a specified step change in pressure. 7. Common mode pressures beyond specified may result in leakage at the case–to–lead interface. 8. Exposure beyond these limits may cause permanent damage or degradation to the device. 9. Offset stability is the product’s output deviation when subjected 1000 hours of Pulsed Pressure, Temperature Cycling with Bias Test. 2 Motorola Sensor Device Data LINEARITY Linearity refers to how well a transducer’s output follows the equation: Vout = Voff + sensitivity x P over the operating pressure range. There are two basic methods for calculating nonlinearity: (1) end point straight line fit (see Figure 2) or (2) a least squares best line fit. While a least squares fit gives the “best case” linearity error (lower numerical value), the calculations required are burdensome. Conversely, an end point fit will give the “worst case” error (often more desirable in error budget calculations) and the calculations are more straightforward for the user. Motorola’s specified pressure sensor linearities are based on the end point straight line method measured at the midrange pressure. LEAST SQUARES FIT RELATIVE VOLTAGE OUTPUT EXAGGERATED PERFORMANCE CURVE LEAST SQUARE DEVIATION STRAIGHT LINE DEVIATION END POINT STRAIGHT LINE FIT OFFSET 50 PRESSURE (% FULLSCALE) 0 100 Figure 2. Linearity Specification Comparison ON–CHIP TEMPERATURE COMPENSATION and CALIBRATION Figure 3 shows the output characteristics of the MPX7200 series at 25°C. The output is directly proportional to the differential pressure and is essentially a straight line. 40 VS = 10 Vdc TA = 25°C P1 > P2 OUTPUT (mVdc) 35 30 25 The effects of temperature on Full Scale Span and Offset are very small and are shown under Operating Characteristics. TYP SPAN RANGE (TYP) MAX 20 15 10 MIN 5 0 –5 kPa 0 PSI 25 50 7.25 75 125 100 14.5 PRESSURE 150 21.75 175 200 29 OFFSET Figure 3. Output versus Pressure Differential SILICONE GEL DIE COAT DIFFERENTIAL/GAUGE STAINLESS STEEL DIE METAL COVER P1 EPOXY CASE ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ WIRE BOND LEAD FRAME DIFFERENTIAL/GAUGE ELEMENT P2 DIE BOND SILICONE GEL ABSOLUTE DIE COAT DIE P1 STAINLESS STEEL METAL COVER EPOXY CASE ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ WIRE BOND LEAD FRAME ABSOLUTE ELEMENT P2 DIE BOND Figure 4. Cross–Sectional Diagrams (Not to Scale) Figure 4 illustrates the absolute sensing configuration (right) and the differential or gauge configuration in the basic chip carrier (Case 344–15). A silicone gel isolates the die surface and wire bonds from the environment, while allowing the pressure signal to be transmitted to the silicon diaphragm. The MPX7200 series pressure sensor operating charac- Motorola Sensor Device Data teristics and internal reliability and qualification tests are based on use of dry air as the pressure media. Media other than dry air may have adverse effects on sensor performance and long term reliability. Contact the factory for information regarding media compatibility in your application. 3 PRESSURE (P1)/VACUUM (P2) SIDE IDENTIFICATION TABLE Motorola designates the two sides of the pressure sensor as the Pressure (P1) side and the Vacuum (P2) side. The Pressure (P1) side is the side containing the silicone gel which isolates the die from the environment. The differential and gauge sensor is designed to operate with positive differPart Number MPX7200A ential pressure applied, P1 > P2. The absolute sensor is designed for vacuum applied to P1 side. The Pressure (P1) side may be identified by using the table below: Case Type MPX7200D Pressure Side (P1) Identifier 344–15C Stainless Steel Cap 344C–01 Side with Part Marking 344B–01 Side with Port Attached MPX7200GVP 344D–01 Stainless Steel Cap MPX7200AS 344E–01 Side with Port Attached 344F–01 Side with Port Attached 344G–01 Stainless Steel Cap MPX7200DP MPX7200AP MPX7200ASX MPX7200GP MPX7200GSX MPX7200GVSX ORDERING INFORMATION MPX7200 series pressure sensors are available in absolute, differential and gauge configurations. Devices are available in the basic element package or with pressure port fittings which provide printed circuit board mounting ease and barbed hose pressure connections. MPX Series D i Type Device T O i Options C Case Type T Order Number Device Marking Basic Element Absolute, Differential Case 344–15 MPX7200A MPX7200D MPX7200A MPX7200D Ported Elements Differential Case 344C–01 MPX7200DP MPX7200DP Absolute, Gauge Case 344B–01 MPX7200AP MPX7200D MPX7200AP MPX7200GP Gauge Vacuum Case 344D–01 MPX7200GVP MPX7200GVP Absolute, Stove Pipe Case 344E–01 MPX7200AS MPX7200A Absolute, Gauge Axial Case 344F–01 MPX7200ASX MPX7200GSX MPX7200A MPX7200D Gauge Vacuum Axial Case 344G–01 MPX7200GVSX MPX7200D 4 Motorola Sensor Device Data PACKAGE DIMENSIONS NOTES: C 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION –A– IS INCLUSIVE OF THE MOLD STOP RING. MOLD STOP RING NOT TO EXCEED 16.00 (0.630). POSITIVE PRESSURE (P1) R M B –A– DIM A B C D F G J L M N R N 1 PIN 1 2 3 L 4 –T– SEATING PLANE J POSITIVE PRESSURE (P1) G F D 4 PL 0.136 (0.005) T A M M INCHES MIN MAX 0.595 0.630 0.514 0.534 0.200 0.220 0.016 0.020 0.048 0.064 0.100 BSC 0.014 0.016 0.695 0.725 30_ NOM 0.475 0.495 0.430 0.450 STYLE 1: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 15.11 16.00 13.06 13.56 5.08 5.59 0.41 0.51 1.22 1.63 2.54 BSC 0.36 0.40 17.65 18.42 30_ NOM 12.07 12.57 10.92 11.43 GROUND + OUTPUT + SUPPLY – OUTPUT CASE 344–15 ISSUE W SEATING PLANE NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5, 1982. 2. CONTROLLING DIMENSION: INCH. –A– –T– U L R H N PORT #1 POSITIVE PRESSURE (P1) –Q– B 1 2 3 4 PIN 1 K –P– 0.25 (0.010) J M T Q S S F C G D 4 PL 0.13 (0.005) M T S S Q S DIM A B C D F G H J K L N P Q R S U INCHES MIN MAX 1.145 1.175 0.685 0.715 0.305 0.325 0.016 0.020 0.048 0.064 0.100 BSC 0.182 0.194 0.014 0.016 0.695 0.725 0.290 0.300 0.420 0.440 0.153 0.159 0.153 0.159 0.230 0.250 0.220 0.240 0.910 BSC STYLE 1: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 29.08 29.85 17.40 18.16 7.75 8.26 0.41 0.51 1.22 1.63 2.54 BSC 4.62 4.93 0.36 0.41 17.65 18.42 7.37 7.62 10.67 11.18 3.89 4.04 3.89 4.04 5.84 6.35 5.59 6.10 23.11 BSC GROUND + OUTPUT + SUPPLY – OUTPUT CASE 344B–01 ISSUE B Motorola Sensor Device Data 5 PACKAGE DIMENSIONS — CONTINUED PORT #1 R NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. –A– U V W L H PORT #2 PORT #1 POSITIVE PRESSURE (P1) PORT #2 VACUUM (P2) N –Q– B SEATING PLANE SEATING PLANE 1 2 3 4 PIN 1 K –P– –T– –T– 0.25 (0.010) T Q M S S F J G D 4 PL C 0.13 (0.005) M T S S Q S DIM A B C D F G H J K L N P Q R S U V W INCHES MIN MAX 1.145 1.175 0.685 0.715 0.405 0.435 0.016 0.020 0.048 0.064 0.100 BSC 0.182 0.194 0.014 0.016 0.695 0.725 0.290 0.300 0.420 0.440 0.153 0.159 0.153 0.159 0.063 0.083 0.220 0.240 0.910 BSC 0.248 0.278 0.310 0.330 STYLE 1: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 29.08 29.85 17.40 18.16 10.29 11.05 0.41 0.51 1.22 1.63 2.54 BSC 4.62 4.93 0.36 0.41 17.65 18.42 7.37 7.62 10.67 11.18 3.89 4.04 3.89 4.04 1.60 2.11 5.59 6.10 23.11 BSC 6.30 7.06 7.87 8.38 GROUND + OUTPUT + SUPPLY – OUTPUT CASE 344C–01 ISSUE B NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5, 1982. 2. CONTROLLING DIMENSION: INCH. –A– U L SEATING PLANE –T– R DIM A B C D F G H J K L N P Q R S U H PORT #2 VACUUM (P2) POSITIVE PRESSURE (P1) N –Q– B 1 2 3 4 K PIN 1 S C J F –P– 0.25 (0.010) M T Q S G D 4 PL 0.13 (0.005) M T S S Q S INCHES MIN MAX 1.145 1.175 0.685 0.715 0.305 0.325 0.016 0.020 0.048 0.064 0.100 BSC 0.182 0.194 0.014 0.016 0.695 0.725 0.290 0.300 0.420 0.440 0.153 0.159 0.153 0.158 0.230 0.250 0.220 0.240 0.910 BSC STYLE 1: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 29.08 29.85 17.40 18.16 7.75 8.26 0.41 0.51 1.22 1.63 2.54 BSC 4.62 4.93 0.36 0.41 17.65 18.42 7.37 7.62 10.67 11.18 3.89 4.04 3.89 4.04 5.84 6.35 5.59 6.10 23.11 BSC GROUND + OUTPUT + SUPPLY – OUTPUT CASE 344D–01 ISSUE B 6 Motorola Sensor Device Data PACKAGE DIMENSIONS — CONTINUED PORT #1 POSITIVE PRESSURE (P1) –B– C NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. A BACK SIDE VACUUM (P2) DIM A B C D F G J K N R S V V 4 3 2 1 PIN 1 K J N MILLIMETERS MIN MAX 17.53 18.28 6.22 6.48 19.81 20.82 0.41 0.51 1.22 1.63 2.54 BSC 0.36 0.41 8.76 9.53 7.62 7.87 4.52 4.72 5.59 6.10 4.62 4.93 G STYLE 1: PIN 1. 2. 3. 4. F R SEATING PLANE S INCHES MIN MAX 0.690 0.720 0.245 0.255 0.780 0.820 0.016 0.020 0.048 0.064 0.100 BSC 0.014 0.016 0.345 0.375 0.300 0.310 0.178 0.186 0.220 0.240 0.182 0.194 D 4 PL 0.13 (0.005) –T– M T B M GROUND + OUTPUT + SUPPLY – OUTPUT CASE 344E–01 ISSUE B –T– C A E –Q– U N V B R PORT #1 POSITIVE PRESSURE (P1) PIN 1 –P– 0.25 (0.010) M T Q M 4 3 2 1 S K J F NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. DIM A B C D E F G J K N P Q R S U V INCHES MIN MAX 1.080 1.120 0.740 0.760 0.630 0.650 0.016 0.020 0.160 0.180 0.048 0.064 0.100 BSC 0.014 0.016 0.220 0.240 0.070 0.080 0.150 0.160 0.150 0.160 0.440 0.460 0.695 0.725 0.840 0.860 0.182 0.194 MILLIMETERS MIN MAX 27.43 28.45 18.80 19.30 16.00 16.51 0.41 0.51 4.06 4.57 1.22 1.63 2.54 BSC 0.36 0.41 5.59 6.10 1.78 2.03 3.81 4.06 3.81 4.06 11.18 11.68 17.65 18.42 21.34 21.84 4.62 4.92 G D 4 PL 0.13 (0.005) M T P S Q S STYLE 1: PIN 1. 2. 3. 4. GROUND V (+) OUT V SUPPLY V (–) OUT CASE 344F–01 ISSUE B Motorola Sensor Device Data 7 PACKAGE DIMENSIONS — CONTINUED –T– C A E –Q– U POSITIVE PRESSURE (P1) N V B R PIN 1 PORT #2 VACUUM (P2) –P– 0.25 (0.010) M T Q M 1 2 3 4 S K F J G D 4 PL 0.13 (0.005) M T P S Q S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. DIM A B C D E F G J K N P Q R S U V INCHES MIN MAX 1.080 1.120 0.740 0.760 0.630 0.650 0.016 0.020 0.160 0.180 0.048 0.064 0.100 BSC 0.014 0.016 0.220 0.240 0.070 0.080 0.150 0.160 0.150 0.160 0.440 0.460 0.695 0.725 0.840 0.860 0.182 0.194 STYLE 1: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 27.43 28.45 18.80 19.30 16.00 16.51 0.41 0.51 4.06 4.57 1.22 1.63 2.54 BSC 0.36 0.41 5.59 6.10 1.78 2.03 3.81 4.06 3.81 4.06 11.18 11.68 17.65 18.42 21.34 21.84 4.62 4.92 GROUND V (+) OUT V SUPPLY V (–) OUT CASE 344G–01 ISSUE B Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315 Mfax: [email protected] – TOUCHTONE 602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, – US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 INTERNET: http://motorola.com/sps 8 ◊ MPX7200/D Motorola Sensor Device Data