DTD113ZK / DTD113ZU / DTD113ZS Transistors 500mA / 50V Digital transistors (with built-in resistors) DTD113ZK / DTD113ZU / DTD113ZS zExternal dimensions (Unit : mm) zApplications Inverter, Interface, Driver 2.9 DTD113ZK 1.1 0.4 0.8 (2) (1) 0.3Min. zFeatures 1) Built-in bias resistors enable theconfiguration of an inverter circuit without connecting external input resistors (see equivalent circuit). 2) The bias resistors consist of thin-film resistors negative biasing of the input. They also have the advantage of almost completely eliminat ing parasitic effects. 3) Only the on/off conditions need to be set for operation, making the device design easy. 1.6 2.8 (3) 0.95 0.95 0.15 1.9 ROHM : SMT3 EIAJ : SC-59 Each lead has same dimensions Abbreviated symbol: G21 DTD113ZU 2.0 (1) GND (2) IN (3) OUT 0.9 0.7 0.2 0.3 (1) (2) 0.65 0.65 ROHM : UMT3 EIAJ : SC-70 0.15 1.3 Each lead has same dimensions Abbreviated symbol: G21 Part No. SPT Packaging type Taping Taping Taping Code T146 T106 TP Basic ordering unit (pieces) 3000 3000 5000 − − DTD113ZK DTD113ZU − DTD113ZS − − − 4.0 DTD113ZS 2.0 3Min. SMT3 UMT3 (1) GND (2) IN (3) OUT 3.0 Package (15Min.) zPackaging specifications 0.1Min. zStructure NPN epitaxial planar silicon transistor (Resistor built-in type) 2.1 1.25 (3) ROHM : SPT EIAJ : SC-72 0.45 2.5 0.45 0.5 5.0 (1) (2) (3) Abbreviated symbol : D113ZS (1) GND (2) OUT (3) IN zEquivalent circuit OUT R1 IN R2 GND OUT IN GND R1=1.0kΩ, R2=10kΩ Rev.B 1/3 DTD113ZK / DTD113ZU / DTD113ZS Transistors zAbsolute maximum ratings (Ta=25°C) Parameter Symbol Limits DTD113ZU DTD113ZK DTD113ZS Unit Supply voltage Input voltage VCC 50 VIN −5 to +10 V Output current IC 500 mA Power dissipation PD V 200 300 mW Junction temperature Tj 150 °C Storage temperature Tstg −55 to +150 °C zElectrical characteristics (Ta=25°C) Parameter Symbol Min. Typ. Max. VI(off) − − 0.3 VI(on) 1.5 − − VO(on) − 0.1 0.3 V II − − 7.2 mA VI=5V IO(off) − − 0.5 µA VCC=50V, VI=0V VO=5V, IO=50mA Input voltage Output voltage Input current Output current Unit V Conditions VCC=5V, IO=100µA VO=0.3V, IO=20mA IO/II=50mA/2.5mA DC current gain GI 82 − − − Input resistance R1 0.7 1 1.3 kΩ − Resistance ratio R2/R1 8 10 12 − − fT ∗ − 200 − MHz Transition frequency VCE=10V, IE=−50mA, f=100MHz ∗ Characteristics of built-in transistor Rev.B 2/3 DTD113ZK / DTD113ZU / DTD113ZS Transistors zElectrical characteristic curves 100 10m VO=0.3V 1k VCC=5V 5m 500 20 10 5 Ta=−40°C 25°C 100°C 2 1 500m 200m 100m 500µ 1m 2m DC CURRENT GAIN : GI OUTPUT CURRENT : Io (A) INPUT VOLTAGE : VI (on) (V) 50 1m 50µ Ta=100 °C 25 °C −40 °C 200µ 100µ 50µ 20µ 10µ 5µ 2m 5m 10m 20m 50m 100m 200m 500m 0 100 50 20 10 5 2 2µ 1µ 200 VO=5V Ta=100°C 25°C −40°C 0.5 1.0 1.5 2.0 2.5 3.0 1 500µ 1m 2m 5m 10m 20m 50m 100m200m 500m OUTPUT CURRENT : IO (A) INPUT VOLTAGE : VI (off) (V) OUTPUT CURRENT : IO (A) Fig.1 Input voltage vs. output current (ON characteristics) Fig.2 Output current vs. input voltage (OFF characteristics) Fig. 3 DC current gain vs. output current 1 lO/lI=20 OUTPUT VOLTAGE : VO (on) (V) 500m Ta=100°C 25°C −40°C 200m 100m 50m 20m 10m 5m 2m 1m 500µ 1m 2m 5m 10m 20m 50m100m200m 500m OUTPUT CURRENT : IO (A) Fig.4 Output voltage vs. output current Rev.B 3/3 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1