Long Distance Reflective Switch OPB732, OPB732WZ OPB732 Features: PC board mounting (OPB732) 24” (610 mm) 26 AWG wired with mounting tabs (OPB732WZ) Non-contact infrared switch Up to 1” or more reflective distance depending on circuitry Product Photo Here OPB732WZ Description: OPB732 uses an Infrared LED and Phototransistor in a reflective switch configuration. The assembly is offered with either PCBoard through hole pins (OPB732) or 24” (610 mm), 26 AWG wires (OPB732WZ), and uses an opaque housing to reduce the sensor’s ambient light sensitivity. The emitter and sensor are protected by a clear window, providing a device that can operate in a dusty environment. The phototransistor can be configured as a Common Collector or Common Emitter device. While an object is in the reflective path of the device, light from the LED will be reflected back to the housing irradiating the surface (base) of the phototransistor. When Infrared light strikes the phototransistor, the transistor becomes forward biased and is considered to be in the “ON” state, providing an IC(ON) current proportional to the light striking the phototransistor. With the Infrared light from the LED not being reflected to the phototransistor, the phototransistor turns “OFF,” minimizing the IC(ON) current. Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information. Applications: Ordering Information Non-contact reflective object sensor Door sensor Assembly line automation Machine safety Machine automation End of travel sensor Equipment security Door sensor Part Number OPB732 850 nm OPB732WZ 3 4 2 0.150”/ see diagram 24" / 26 AWG Wire Pin # LED Green-1 Emitter White-2 Collector Red-3 Anode Black-4 Cathode 1 OPB732 RoHS LED Peak Lead Length / Spacing Wavelength OPB732WZ OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A .2 02/06 Page 1 of 3 Long Distance Reflective Switch OPB732, OPB732WZ Absolute Maximum Ratings (TA = 25o C unless otherwise noted) Storage Temperature -40° C to +100° C Operating Temperature -40° C to +85° C Lead Soldering Temperature (1/16” (1.6mm) from case for 5 seconds with soldering iron) (2) 260° C LED Forward Current 50 mA Peak Forward current (2 µs pulse width, 0.1% Duty Cycle) 1A Reverse DC Voltage 3V Power Dissipation 100 mW Output Photo Transistor Collector-Emitter Voltage 30 V Collector DC Current 50 mA Power Dissipation 100 mW Electrical Characteristics (TA = 25 C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS CONDITIONS Input LED (See OP240 for additional information, reference only) VF Forward Voltage - - 1.8 V IR Reverse Current - - 100 µA IF = 20 mA VR = 2 V Output Phototransistor (See OP550 for additional information, reference only) V(BR)CEO ICEO 30 - - V I C = 100 µA, EE = 0 mw/cm2 Collector-Emitter Dark Current - - 100 nA VCE = 10 V, EE = 0 mw/cm2 Collector-Emitter Saturation Voltage(4) - - 0.4 V IC = 250 µA, I F = 30 mA , (4) 0.25 - - mA VCE = 1 V, IF = 30 mA, (4) - - 50 µA VCE = 5 V, IF = 30 mA, No reflective surface Collector-Emitter Breakdown Voltage Coupled VCE(SAT) IC(ON) ICX On-State Collector Current(4) Cross Talk Notes: (1) All parameters tested using pulse technique. (2) RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. (3) Methanol or isopropanol are recommended as cleaning agents. The plastic housing is soluble in chlorinated hydrocarbons and keytones. (4) Distance = 1” (from front of package to a 90% diffuse reflective white card) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.2 02/06 Page 2 of 3 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Long Distance Reflective Switch OPB732, OPB732WZ IC(ON)IC(ON) vs Distance vs Distance(I(IF=30mA) F=30mA) 1.6 Normalized at 1.00 inches 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 Distance (inches) DC—Drive Circuit for LED & Phototransistor VCC V - VLED R = CC D ID RD RL VCC V - VCE RL = CC IL V - VLED RD = CC ID Inverted Output Light RD Light Output R L VEE (GND) V -V CE RL = CC I L VEE (GND) Pulsed - Driver Circuits forLED LED & & Phototransistor Phototransistor Pulsed—Drive Circuit for VCC V - VLED - VCE RD = CC ID RD RL Light Drive Ckt. V CC V - VCE RL = CC IL V - VLED - VCE RD = CC ID Inverted Output RD Light Output Drive Ckt. RL VEE (GND) V - VCE RL = CC IL VEE (GND) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A .2 02/06 Page 3 of 3