Gamma GM393 Low power dual differential comparator Datasheet

GM393
LOW POWER DUAL
DIFFERENTIAL COMPARATOR
Description
Features
The GM393 consists of two independent
precision voltage comparators with an offset
voltage specification as low as 2.0 mV max for
two comparators which were designed
specifically to operate from a single power
supply over a wide range of voltages. Operation
from split power supplies is also possible and
the low power supply current drain is
independent of the magnitude of the power
supply voltage. These comparators also have a
unique characteristic. In that, the input commonmode voltage range includes ground, even
though operated from a single power supply
voltage.
‹
Single- supply Range: ±1.0V to ±18V
‹
Wide supply voltage range: ±2.0V to
±36V
‹
Very low supply current drain (0.4 mA) -
‹
independent of supply voltage
‹
Low input biasing current: 25 nA
‹
Low input offset current: ±5 nA
‹
Maximum offset voltage: ±3 mV
‹
Input common-mode voltage range
includes ground
Application areas include limit comparators,
simple analog to digital converters; pulse,
square wave and time delay generators; wide
range VCO; MOS clock timers; multivibrators
and high voltage digital logic gates. The GM393
are designed to directly interface with TTL and
CMOS. When operated from both plus and
minus power supplies, the GM393 will directly
interface with MOS logic, where their low power
drain is a distinct advantage over standard
comparators.
‹
Differential input voltage range equal to
the power supply voltage
‹
Low output saturation voltage: 250 mV
at 4 mA
‹
Output voltage compatible with TTL,
DTL, ECL, MOS and CMOS logic
systems
The GM393 is available in DIP-8 and SOP-8
packages.
Application
High precision comparators
Wide Range VCO
Simple Analog to Digital Converters
MOS Clock Timer
GM393V1.00
Pulse, Square Wave Generators
1
GM393
LOW POWER DUAL
DIFFERENTIAL COMPARATOR
Connecting Diagram
(Top View)
Output A
1
8
Inverting
Input A-
2
7
NON - Inverting
Input A+
GND
-
3
A
+
+
B
-
4
VCC
Output B
6
Inverting
Input B-
5
NON - Inverting
Input B+
SOP-8, DIP-8 PACKAGE
Marking Information and Pin Configurations (Top View)
SO8
7.
DIP8
6. Input B
Output B
-
7.
5. Input B +
8. VCC
6. Input B 5. Input B +
Output B
8. VCC
GM393
AYWW
GM393
AYWW
1. Output A
2.
1. Output A
4.
Gnd
Input A -
3.
Input A +
2.
4. Gnd
3. Input A +
Input A -
GM393V1.00
A: Assembly / Test site code
Y: Year
WW: Week
2
Ordering Information
Ordering Number
Package
Shipping
GM393D8T
DIP-8
60 Units / Tube
GM393S8T
SOP-8
100 Units / Tube
GM393S8R
SOP-8
2,500 Units / Tape & Reel
www.gammamicro.com.tw
GM393
LOW POWER DUAL
DIFFERENTIAL COMPARATOR
Absolute Maximum Ratings
PARAMETER
RATINGS
UNITS
±18 or 36
V
Input Current
50
mA
Input Voltage
-0.3 to +32
V
Supply Voltage
Power dissipation
DIP 8
780
SO 8
510
mW
Operating Temperature Range
-40 to 125
℃
Storage Temperature
- 65 to 150
℃
260
℃
Lead Temperature (soldering 10 sec.)
Block Diagram
VCC
VIN +
VOUT
GM393V1.00
VIN -
3
GM393
LOW POWER DUAL
DIFFERENTIAL COMPARATOR
Electrical Characteristics (VCC = 5V, at specified free-air temperature, unless otherwise
specified)
Parameter
Symbol
Condition
Input offset Voltage
VIO
VCC = 5V to Max
VIC = VICR min
VO = 1.4V
Input Offest Current
IIO
VO = 1.4V
Input Bias Current
IIB
VO =1.4V
Min
TA = 25℃
Typ
Max
±2
±5
Full Range
TA = 25℃
±5
Full Range
±50
nA
±150
TA = 25℃
-20
Full Range
-250
nA
400
TA = 25℃
0 to VCC-1.5V
Full Range
0 to VCC-2.0V
VICR
High-Level output
Voltage
VOL
IOL = 4mA, VID = 1V
Large-Signal
Differential Voltage
Amplification
AVD
VCC = 15V,
VO = 1V to 11V
RL = 15K to VCC
TA = 25℃
High Level Output
Current
IOH
VOH = 5V, VID = 1V
TA = 25℃
0.1
VOH = 30V, VID = 1V
Full Range
1
Low Level Output
Current
IOL
VOH = 1.5V, VID = -1V
TA = 25℃
Supply Current
ICC
RL = ∞, VCC = 5V
TA = 25℃
RL = ∞, VCC = 30V
Full Range
Response Time
(Note 1)
mV
9
Common-Mode Input
Voltage Range**
RL Connected to
5V through 5.1k.
CL = 15pF
Unit
TA = 25℃
V
150
Full Range
400
mV
700
50
200
V/mV
50
nA
µA
6
mA
0.8
1.0
2.5
100mV input
step with 5mV
overdrive
1.3
TTL - level input
step
0.3
mA
µs
All characteristics are measured under open loop conditions with zero common-mode input voltage unless otherwise specified.
"MAX" VCC for testing purposes is 30V. Full range is 0°C to 70°C.
** The voltage at either input or common - mode should not be allowed to go negative by more than 0.3V. The upper end of the
common - mode voltage range is VCC - 1.5V, but either or both inputs can go to 30V without damage.
GM393V1.00
Note 1: CL includes probe and jig capacitance. The response time specified is the interval between the input step function and the
instant when the output crosses 1.4V.
4
GM393
LOW POWER DUAL
DIFFERENTIAL COMPARATOR
Typical Performance Characteristics
80
10
Out of
Saturation
60
TA = -55°C
50
TA = 0°C
40
TA = 25°C
30
20
TA = 70°C
TA = 125°C
10
0
0
5
10
15
20
25
30
35
40
VCC, Supply Voltage (VDC)
Figure 1. Input Bias Current versus Power
Supply Voltage
1.0
1.0
TA = 125°C
0.1
TA = 25°C
TA = -55°C
0.01
0.001
0.01
0.1
1.0
10
100
ISINK, Output Sink Current (mA)
Figure 2. Output Saturation Voltage v.s.
Output Sink Current
TA = -55°C
TA = 0°C
0.8
TA = 25°C
0.6
TA = 70°C
0.4
TA = 125°C
0.2
0.0
0
RL = ∞
5
10
15
20
25
30
35
40
VCC, Supply Voltage (VDC)
Figure 3. Power Supply Current versus
Power Supply Voltage
GM393V1.00
ICC, Supply Current (mA)
VOL, Saturation Voltage (VDC)
IIB, Input Bias Current (nA)
70
5
GM393
LOW POWER DUAL
DIFFERENTIAL COMPARATOR
Package Outline Dimensions – SO 8
0.189 - 0.197
(4.800 - 5.004)
0.228 - 0.244
(5.791 - 6.198)
0.016 - 0.050
(0.406 - 0.270)
D
0.014 - 0.020
(0.356 - 0.508)
0.050
(1.270)
TYP
0.150 - 0.157
(3.810 - 3.988)
0.053 - 0.059
(1.346 - 1.753)
SEATING PLAN
0.004 - 0.010
(0.012 - 0.254)
8.0
MAX
0.008 - 0.010
(0.203 - 0.254)
Package Outline Dimensions – DIP 8
0.250 +/- 0.005
(6.350 +/- 0.127)
0.370 - 0.400
(9.474 - 10.150)
0.300 - 0.320
(7.620 - 8.128)
0.06
(1.524)
GM393V1.00
0.145 - 0.200
(3.683 - 5.080)
6
0.125 - 0.140
(3.175 - 3.556)
0.045 +/- 0.015
(1.143 +/- 0.183)
0.108 +/- 0.003
(0.457 +/- 0.076)
0.100 +/- 0.010
(2.540 +/- 0.254)
J
0.009 - 0.010
(0.299 - 0.381)
95 +/- 5
GM393
LOW POWER DUAL
DIFFERENTIAL COMPARATOR
GM
Circuit Type
393
Circuit Type
S8
R
Package Type
Shipping Type
S8: SO 8
D8: DIP 8
R: Taping & Reel
T: Tube
GM393V1.00
Ordering Number
1
7
Similar pages