a Simultaneous Sampling Video Rate Codec ADV7202 FEATURES Four 10-Bit Video DACs (4:2:2, YCrCb, RGB I/P Supported) 10-Bit Video Rate Digitization at up to 54 MHz AGC Control (ⴞ6 dB) Front End 3-Channel Clamp Control Up to Five CVBS Input Channels, Two Component YUV, Three S-Video, or a Combination of the Above. Simultaneous Digitization of Two CVBS Input Channels Aux 8-Bit SAR ADC @ 843 kHz Sampling Giving up to Eight General-Purpose Inputs I2C Compatible Interface with I2C Filter RGB Inputs for Picture-on-Picture of the RGB DACs Optional Internal Reference Power Save Mode APPLICATIONS Picture-on-Picture Video Systems Simultaneous Video Rate Processing Hybrid Set-Top Box TV Systems Direct Digital Synthesis/I-Q Demodulation Image Processing GENERAL DESCRIPTION The ADV7202 is a video rate sampling codec. It has the capability of sampling up to five NTSC/PAL/SECAM video I/P signals. The resolution on the front end digitizer is 12 bits; 2 bits (12 dB) are used for gain and offset adjustment. The digitizer has a conversion rate of up to 54 MHz. The ADV7202 can have up to eight auxiliary inputs that can be sampled by an 843 kHz SAR ADC for system monitoring. The back end consists of four 10-bit DACs that run at up to 200 MHz and can be used to output CVBS, S-Video, Component YCrCb, and RGB. This codec also supports Picture-on-Picture. The ADV7202 can operate at 3.3 V or 5 V. Its monolithic CMOS construction ensures greater functionality with lower power dissipation. The ADV7202 is packaged in a small 64-lead LQFP package. FUNCTIONAL BLOCK DIAGRAM XTAL AIN1P AIN1M SHA AND CLAMP AIN2P AIN2M AIN3P AIN3M AIN4P AIN4M AIN5P AIN5M AIN6P AIN6M DOUT DAC_DATA [9:0] [9:0] 10-BIT ADC BLOCK D/A 12-BIT 12-BIT SHA AND CLAMP I/P I/P MUX MUX OSD I/P “S” DAC0 A/D A/D 10-BIT SHA AND CLAMP D/A ADC LOGIC DAC1 DAC LOGIC 10-BIT 8-BIT 843kHz A/D A/D D/A DAC2 10-BIT D/A DAC3 ADV7202 I2C REV. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 2002 ADV7202* PRODUCT PAGE QUICK LINKS Last Content Update: 11/29/2017 COMPARABLE PARTS DISCUSSIONS View a parametric search of comparable parts. View all ADV7202 EngineerZone Discussions. DOCUMENTATION SAMPLE AND BUY Application Notes Visit the product page to see pricing options. • AN-205: Video Formats and Required Load Terminations • Low Cost, Two-Chip, Voltage -Controlled Amplifier and Video Switch TECHNICAL SUPPORT Data Sheet Submit a technical question or find your regional support number. • ADV7202: Simultaneous Sampling Video Rate CODEC Data Sheet DOCUMENT FEEDBACK Submit feedback for this data sheet. DESIGN RESOURCES • ADV7202 Material Declaration • PCN-PDN Information • Quality And Reliability • Symbols and Footprints This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified. ADV7202–SPECIFICATIONS 5 V SPECIFICATIONS (AVDD/DVDD = 5 V ⴞ 5%, V REF = 1.235 V, RSET = 1.2 k⍀, Parameter STATIC PERFORMANCE_DAC Resolution (Each DAC) Accuracy (Each DAC) Integral Nonlinearity Differential Nonlinearity Min Typ –1.5 10 10 ± 0.6 –0.6/0.1 VIDEO ADC Resolution Accuracy Integral Nonlinearity Differential Nonlinearity Input Voltage Range2 SNR AUX ADC Resolution Differential Nonlinearity Integral Nonlinearity Input Voltage Range DIGITAL INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Leakage Current, IIN Input Capacitance, CIN DIGITAL OUTPUTS Output High Voltage, VOH Output Low Voltage, VOL Three-State Leakage Current Output Capacitance Digital Output Access Time, t14 Digital Output Hold Time, t15 ANALOG OUTPUTS Output Current Range DAC-to-DAC Matching Output Compliance, VOC Output Impedance, ROUT Output Capacitance, COUT Analog Output Delay3 DAC Output Skew VOLTAGE REFERENCE Reference Range, VREFDAC Reference Range, VREFADC Reference Range, VREFADC Max Unit Test Conditions +0.5 Bits Bits LSB LSB 10-Bit Operation 10-Bit Operation 12 Bits 12 ± 2.5 ± 0.7 Bits LSB LSB 12 Bit 12 Bit 62 57 dB dB 27 MHz Clock 54 MHz Clock 8 ± 0.4 ± 0.4 Bits LSB LSB V –VREFADC 2 VREFADC 2 0.8 ±2 6 2.4 0.4 10 10 6 5 4.33 3 0 4.6 1.4 50 30 5.5 0.06 1.17 2.1 (Including 2 Bits for Gain Ranging) 2.2 V Ref. +VREFADC 0 4.10 all specifications TMIN to TMAX1, unless otherwise noted.) 1.235 2.2 1.1 1.30 2.30 Guaranteed No Missing Codes V V µA pF V V µA pF ns ns ISOURCE = 400 µA ISINK = 1.6 mA mA % V kΩ pF ns ns RSET = 1.2 kΩ, RL = 300 Ω V V V See Figure 13 IOUT = 0 mA Programmable 1.1 V or 2.2 V NOTES 1 0°C to 70°C. 2 SHA gain = 1, half range for SHA gain = 2, see Table II. 3 Output delay measured from 50% of the rising edge of the clock to the 50% point of full-scale transition. Specifications subject to change without notice. –2– REV. 0 ADV7202 5 V SPECIFICATIONS (AVDD/DVDD = 5 V ⴞ 5%, VREF = 1.235 V, RSET = 1.2 k⍀, all specifications TMIN to TMAX, unless otherwise noted.) Parameter Min Typ Max Unit 4.75 5 5.25 V 22 12 115 mA mA mA mA µA ms Test Conditions 1 POWER REQUIREMENTS AVDD/DVDD Normal Power Mode IDAC2 IDSC3 IADC4 IADC4 Sleep Mode Current5 Power-Up Time MPU PORT6—I2C SCLOCK Frequency SCLOCK High Pulsewidth, t1 SCLOCK Low Pulsewidth, t2 Hold Time (Start Condition), t3 Setup Time (Start Condition), t4 Data Setup Time, t5 SDATA, SCLOCK Rise Time, t6 SDATA, SCLOCK Fall Time, t7 Setup Time (Stop Condition), t8 95 65 400 4 0 0.6 1.3 0.6 400 0.6 100 300 300 0.6 NOTES 1 All DACs and ADCs on. 2 IDAC is the DAC supply current. 3 IDSC is the digital core supply current. 4 IADC is the ADC supply current. 5 This includes I ADC, IDAC, and IDSC. 6 Guaranteed by characterization. Specifications subject to change without notice. REV. 0 –3– kHz µs µs µs µs ns ns ns µs RSET = 1.2 kΩ, RL = 300 Ω Inputs at Supply Max Power YUV Mode CVBS Input Mode Internal Reference After this period the first clock is generated. Relevant for Repeated Start Condition ADV7202–SPECIFICATIONS 5 V SPECIFICATIONS (AVDD/DVDD = 4.75 V – 5.25 V, V 1 REF = 1.235 V, RSET = 1.2 k⍀, all specifications TMIN to TMAX , unless otherwise noted.) Parameter Min PROGRAMMABLE GAIN AMPLIFIER Video ADC Gain Typ –6 Max Unit Condition2 +6 dB Setup Conditions 3 CLAMP CIRCUITRY Clamp Fine Source/Sink Current Clamp Coarse Source/Sink Current CLOCK CONTROL4 DACCLK0/DACCLK1 DACCLK15, 6, 7 DACCLK1 Data Setup Time, t127 Data Hold Time, t137 Min Clock High Time, t107 Min Clock Low Time, t117 Pipeline Delay8 Video ADC RESET CONTROL RESET Low Time µA mA 4.0 0.8 27 1.5 1.5 MHz MHz MHz ns ns ns ns 4 Clock Cycles 10 ns 200 27 1.5 1.5 Dual CLK Dual Edge Mode Single Edge Single Clock Mode 4:2:2 Mode All Input Modes NOTES 1 Temperature range T MIN to TMAX: 0oC to 70oC. 2 The max/min specifications are guaranteed over this range. The max/min values are typical over 4.75 V to 5.25 V range. 3 External clamp capacitor = 0.1 µF. 4 TTL input values are 0 V to 3 V, with input rise/fall times ≤3 ns, measured between the 10% and 90% points. Timing reference points at 50% for inputs and outputs. Analog output load ≤10 pF. 5 Maximum clock speed determined by setup and hold conditions. 6 Single DAC only. 7 Guaranteed by characterization. 8 Output delay measured from the 50% point of the rising edge of CLOCK to the 50% point of full-scale transition. Specifications subject to change without notice. –4– REV. 0 ADV7202 3.3 V SPECIFICATIONS (AVDD/DVDD = 3.3 V ⴞ 5%, VREF = 1.235 V, RSET = 1.2 k⍀, all specifications TMIN to TMAX1, unless otherwise noted.) Parameter Min Typ Max Unit Test Conditions 10-Bit Operation 10-Bit Operation STATIC PERFORMANCE_DAC Resolution (Each DAC) Accuracy (Each DAC) Integral Nonlinearity Differential Nonlinearity 10 10 ±1 –0.8/0.1 Bits Bits LSB LSB VIDEO ADC Resolution 12 Bits 12 ±4 ±1 Bits LSB LSB Accuracy Integral Nonlinearity Differential Nonlinearity Differential Input Voltage Range2 SNR AUX ADC Resolution Differential Nonlinearity Integral Nonlinearity Input Voltage Range DIGITAL INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current, IIN Input Capacitance, CIN DIGITAL OUTPUTS Output High Voltage, VOH Output Low Voltage, VOL Three-State Leakage Current Output Capacitance Digital Output Access Time, t14 Digital Output Hold Time, t15 ANALOG OUTPUTS Output Current DAC-to-DAC Matching Output Compliance, VOC Output Impedance, ROUT Output Capacitance, COUT Analog Output Delay3 DAC Output Skew VOLTAGE REFERENCE Reference Range, VREFADC Reference Range, VREFDAC –VREFADC +VREFADC 60 55 dB dB 8 ± 0.5 ± 0.5 Bits LSB LSB V 0 2 VREFADC 2 0.8 ±1 10 12 Bit 12 Bit See Table II 27 MHz Clock, fIN = 100 kHz 54 MHz Clock V V µA pF V V µA pF ns ns ISOURCE = 400 µA ISINK = 1.6 mA RSET = 1.2 kΩ, RL = 300 Ω DAC 0, 1, and 2 50 30 5.5 0.06 mA % V kΩ pF ns ns 1.100 1.235 V V 2.4 0.4 10 10 6 5 4.33 4 0 1.4 NOTES 1 0°C to 70°C. 2 SHA gain = 1, half range for SHA gain = 2, see Table II. 3 Output delay measured from 50% of the rising edge of the clock to the 50% point of full-scale transition. Specifications subject to change without notice. REV. 0 (Including 2 Bits for Gain Ranging) 2.2 V Ref. –5– See Figure 13 IOUT = 0 mA ADV7202–SPECIFICATIONS 3.3 V SPECIFICATIONS (AVDD/DVDD = 3.3 V ⴞ 5%, VREF = 1.235 V, RSET = 1.2 k⍀, all specifications TMIN to TMAX, unless otherwise noted.) Parameter Min Typ Max Unit 3.14 3.3 3.46 V Test Conditions 1 POWER REQUIREMENTS AVDD/DVDD Normal Power Mode IDAC2 IDSC3 IADC4 Sleep Mode Current5 Power-Up Time MPU PORT6—I2C SCLOCK Frequency SCLOCK High Pulsewidth, t1 SCLOCK Low Pulsewidth, t2 Hold Time (Start Condition), t3 Setup Time (Start Condition), t4 Data Setup Time, t5 SDATA, SCLOCK Rise Time, t6 SDATA, SCLOCK Fall Time, t7 Setup Time (Stop Condition), t8 18 8 80 350 4 0 0.6 1.3 0.6 mA mA mA µA ms 400 0.6 100 300 300 0.6 kHz µs µs µs µs ns ns ns µs Inputs at Supply Internal Reference After this period, the first clock is generated. Relevant for Repeated Start Condition NOTES 1 All DACs and ADCs on. 2 IDAC is the DAC supply current. 3 IDSC is the digital core supply current. 4 IADC is the ADC supply current. 5 This includes IADC, IDAC, and IDSC. 6 Guaranteed by characterization. Specifications subject to change without notice. –6– REV. 0 ADV7202 3.3 V SPECIFICATIONS (AVDD/DVDD = 3.3 V ⴞ 5%, V 1 REF = 1.235 V, RSET = 1.2 k⍀, all specifications TMIN to TMAX , unless otherwise noted.) Parameter Min PROGRAMMABLE GAIN AMPLIFIER Video ADC Gain Typ –6 Max Unit +6 dB Condition2 3 CLAMP CIRCUITRY Clamp Fine Source/Sink Current Clamp Coarse Source/Sink Current CLOCK CONTROL4 DACCLK0/DACCLK1 DACCLK15, 6, 7 DACCLK17 Data Setup Time, t12 Data Hold Time, t13 Min Clock High Time, t107 Min Clock Low Time, t117 Pipeline Delay8 Video ADC RESET CONTROL RESET Low Time 4 0.8 µA mA Up/Down Up/Down 27 180 27 2 2 3 3 MHz MHz MHz ns ns ns ns Dual CLK Dual Edge Mode Single Edge Single Clock Mode 4:2:2 Mode All Input Modes 4 Clock Cycles 10 ns NOTES 1 Temperature range T MIN to TMAX: 0oC to 70oC. 2 The max/min specifications are guaranteed over this range. The max/min values are typical over 4.75 V to 5.25 V range. 3 External clamp capacitor = 0.1 µF. 4 TTL input values are 0 V to 3 V, with input rise/fall times ≤3 ns, measured between the 10% and 90% points. Timing reference points at 50% for inputs and outputs. Analog output load ≤10 pF. 5 Maximum clock speed determined by setup and hold conditions. 6 Single DAC only. 7 Guaranteed by characterization. 8 Output delay measured from the 50% point of the rising edge of CLOCK to the 50% point of full-scale transition. Specifications subject to change without notice. REV. 0 –7– ADV7202 ABSOLUTE MAXIMUM RATINGS 1 AVDD to AVSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V DVDD to DVSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Ambient Operating Temperature (TA) . . . . . . . . 0°C to 70°C Storage Temperature (TS) . . . . . . . . . . . . . . –65°C to +150°C Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . 150°C Lead Temperature (Soldering, 10 secs) . . . . . . . . . . . . . 300°C Vapor Phase Soldering (1 minute) . . . . . . . . . . . . . . . . . 220°C IOUT to GND2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to VAA NOTES 1 Stresses above those listed under Absolute Maximum Ratings may cause permanen t damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2 Analog output short circuit to any power supply or common can be of an indefinite duration. ORDERING INFORMATION Model Temperature Range Package Description Package Option ADV7202 0°C to 70°C 64-Lead Plastic Quad Flatpack (LQFP) ST-64 CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the ADV7202 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. WARNING! ESD SENSITIVE DEVICE DAC_DATA8 DAC_DATA9 DAC_DATA7 DAC_DATA5 DVDD DVSS DAC_DATA6 DAC_DATA4 DACCLK0 DACCLK1 DAC_DATA2 DAC_DATA3 DAC_DATA1 SDA SYNC_OUT DAC_DATA0 PIN CONFIGURATION 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 SYNC_IN 1 SCL 2 ALSB 3 48 RESET PIN 1 IDENTIFIER 47 RSET 46 VREFDAC XTAL0 4 45 COMP XTAL1 5 AVDD_ADC 6 44 DAC0_OUT 43 DAC1_OUT AVSS_ADC 7 AIN1P 8 42 AVDD_DAC ADV7202 41 AVSS_DAC TOP VIEW (Not to Scale) AIN1M 9 AIN2P 10 AIN2M 11 40 DAC2_OUT 39 DAC3_OUT 38 OSDIN0 AIN3P 12 AIN3M 13 37 OSDIN1 AIN4P 14 AIN4M 15 AIN5P 16 35 DOUT0 36 OSDIN2 34 DOUT1 33 DOUT2 –8– DOUT5 DOUT4 DOUT3 DOUT7 DOUT6 DOUT8 CAP1 OSDEN DOUT9 CML CAP2 DVSS REFADC AIN6P AIN6M AIN5M 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 REV. 0 ADV7202 PIN FUNCTION DESCRIPTIONS Pin No. Mnemonic Input/ Output 1 SYNC_IN I 2 3 SCL ALSB I I 4 XTAL0 I 5 XTAL1 O 6 7 8–19 20 21 22 AVDD_ADC AVSS_ADC AIN1–AIN6 DVSS REFADC CML P G I G I/O O 23, 24 CAP2, CAP1 I 25 OSDEN I 26–35 36 37 38 39 40 41 42 43 44 45 DOUT[9:0] OSDIN2 OSDIN1 OSDIN0 DAC3_OUT DAC2_OUT AVSS_DAC AVDD_DAC DAC1_OUT DAC0_OUT COMP O I I I O O G P O O O 46 VREFDAC I/O 47 RSET I 48 49–52, 55, 56, 59–62 53 54 57, 58 63 RESET DAC_DATA[9:0] I I DVSS DVDD DACCLK[1:0] SYNC_OUT G P I O 64 SDA I/O REV. 0 Function This signal can be used to synchronize the updating of clamps. Polarity is programmable via I2C. MPU Port Serial Interface Clock Input This signal sets up the LSB of the MPU address. MPU address = 2cH, ALSB = 0, MPU address = 2eH, ALSB = 1. When this pin is tied high, the I2C filter is activated, which reduces noise on the I2C interface. When this pin is tied low, the input bandwidth on the I2C lines is increased. Input terminal for crystal oscillator or connection for external oscillator with CMOS-compatible square wave clock signal. Second Terminal for Crystal Oscillator. Not connected if external clock source is used. ADC Supply Voltage (5 V or 3.3 V) Ground for ADC Supply Analog Signal Inputs. Can be configured differentially or single-ended. Ground for Digital Core Supply Voltage Reference Input or Programmable Reference Out. Common-Mode Level for ADCs. Connect a 0.1 µF capacitor from CML pin to AVSS_ADC. ADC Capacitor Network. Connect a 0.1 µF capacitor from each CAP pin to AVSS_ADC and a 10 µF capacitor across the two CAP pins. Enable data from OSDIN0–OSDIN2 to be switched to the outputs when set to a logic high. ADC Data Output Third Input Channel for On-Screen Display Second Input Channel for On-Screen Display First Input Channel for On-Screen Display General-Purpose Analog Output Analog Output. Can be used to output CVBS, R, or U. Ground for DAC Supply DAC Supply Voltage (5 V or 3.3 V) Analog Output. Can be used to output CVBS, Y, G, or Luma. Analog Output. Can be used to output CVBS, V, B, or Chroma. Compensation pin for DACs. Connect 0.1 µF capacitor from COMP pin to AVDD_DAC. DAC Voltage Reference Output Pin, Nominally 1.235 V. Can be driven by an external voltage reference. Used to control the amplitude of the DAC output current, 1200 Ω resistor gives an I max of 4.33 mA. Master Reset (Asynchronous) DAC Input Data for Four Video Rate DACs Ground for Digital Core Supply Supply Voltage for Digital Core (5 V or 3.3 V) DAC Clocks Output Sync Signal, which goes to a high state while Cr data sample from a YCrCb data stream or C data from a Y/C data stream is output on DOUT[9:0]. MPU Port Serial Data Input/Output –9– ADV7202 FUNCTIONAL DESCRIPTION Analog Inputs Table II. Analog Input Signal Range The ADV7202 has the capability of sampling up to five CVBS video input signals, two component YUV, or three S-Video inputs. Eight auxiliary general-purpose inputs are also available. Table I shows the analog signal input options available and programmable by I2C. When configured for auxiliary input mode, the CVBS inputs are single-ended with the second differential input internally set to VREFADC. The resolution on the front end digitizer is 12 bits; 2 bits (12 dB) are used for gain and offset adjustment. The digitizer has a conversion rate of up to 54 MHz. The eight auxiliary inputs can be used for system monitoring, etc. and are sampled by an 843 kHz* SAR ADC. The analog input signal range will be dependent on the value of VREFADC and the SHA gain see (Table II). Three on-screen display inputs OSDIN[2:0] mux to the DAC outputs to enable support for Picture-on-Picture applications. Table I. Analog Input Signal Data Register Setting 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 Description CVBS in on AIN1 CVBS in on AIN2 CVBS in on AIN3 Reserved CVBS in on AIN5 CVBS in on AIN6 Y/C, Y on AIN1, C on AIN4 Y/C, Y on AIN2, C on AIN3 YUV, Y on AIN2, U on AIN3, V on AIN6 CVBS on AIN1 and 8 AUX. I/Ps AIN3–AIN6*. CVBS on AIN2 and 8 AUX. I/Ps AIN3–AIN6*. SHA Used Sync_Out I/P Mode SHA VREFOUT (V) Gain Input Range (V) Min Max Differential Differential Differential Differential Single-Ended Single-Ended Single-Ended Single-Ended 2.2 2.2 1.1 1.1 2.2 2.2 1.1 1.1 –2.2 –1.1 –1.1 –0.55 0 1.1 0 0.55 1 2 1 2 1 2 1 2 +2.2 +1.1 +1.1 +0.55 4.4 3.3 2.2 1.65 Digital Inputs The DAC digital inputs on the ADV7202 [9:0] are TTL compatible. Data may be latched into the device in three different modes, programmable via I2C. DAC Mode 1, single clock, single edge (see Figure 10) uses only the rising edge of DACCLK1 to latch data into the device. DACCLK0 is a data line that goes high to indicate that the data is for DAC0. Subsequent data-words go to the next DAC in sequence. 0 0 1 1 0 2 0, 1 0, 1 0, 1, 2 Figure 1 Figure 1 Figure 1 DAC Mode 2, dual edge, dual clock (see Figure 11) clocks data in on both edges of DACCLK0 and DACCLK1. Using this option, data can be latched into the device at four times the clock speed. All four DACs are used in this mode. Figure 1 Figure 1 Figure 2 Figure 2 Figure 3 DAC Mode 3, 4:2:2 mode (see Figure 12). Using this option, 4:2:2 video data is latched in using DACCLK1, while DACCLK0 is used as a data line that is brought to a high state when Cr data is input; hence Y will appear on DAC1, Cr on DAC2, and Cb on DAC0. 0 Figure 1 0 Figure 1 Analog Outputs *AUX inputs are single-ended. All other inputs are differential. Analog outputs [DAC0–DAC3] consist of four 10-bit DACs that run at up to 54 MHz or up to 200 MHz if only DAC0 is used. These outputs can be used to output CVBS, S-Video, Component YCrCb, and RGB. Digital Outputs Video data will be clocked out on DOUT[9:0] on the rising edge of XTAL0 (see Figure 13). Auxiliary data can be read out via I2C compatible MPU port. I2C Control I2C operation allows both reading and writing of system registers. Its operation is explained in detail in the MPU Port Description section. *Fclk/32, 843 kHz for nominal 27 MHz –10– REV. 0 ADV7202 The first three bits give the integer value 3, hence these will be set to ‘011.’ The remaining nine bits will have to be set to give the fractional value 0.65, 512 ⫻ 0.65 = 333 = ‘101001101.’ From Equation 2 it can be seen that the Clamp Level is subtracted from the signal before AGC is applied and then added on again afterwards; hence, if the AGC Gain is set to a value of one, the result would be as follows: VIDEO CLAMPING AND AGC CONTROL When analog signal clamping is required, the input signal should be ac-coupled to the input via a capacitor, the clamping control is via the MPU port. The AGC is implemented digitally. For correct operation, the user must program the clamp value to which the signal has been clamped into the ADV7202 I2C Register. This allows the user to specify which signal level is unaffected by the AGC. The digital output signal will be a function of the ADC output, the AGC Gain, and the Clamp Level and can be represented as follows: DOUT = AGC Gain × [ ADC _ DATA – Clamp Level ] + Clamp Level (AGC Gain = 1) DOUT = ADC _ DATA – Clamp Level + Clamp Level = ADC _ Data (1) FUNCTIONAL DESCRIPTION Clamp and AGC Control DOUT will be a 10-bit number (0–1023), the AGC Gain defaults to 2 and can have a value between 0 to 7.99. The Clamp Level is a 10-bit number (0–1023) equal to the 7-bit I2C value ⫻ 16 (Clamp Level CR06-CR00); the ADC value can be regarded as a 10-bit number (0–1023) for the equation. It should be noted that the ADC resolution is 12 bits. The above equation is used to give a basic perspective and is mathematically correct. The ADV7202 has a front end 3-channel clamp control. To perform an accurate AGC gain operation, it is necessary to know to what level the user is clamping the black level; this value is programmable in Clamp Register 0 CR00–CR06. Each channel has a fine and coarse clamp; the clamp direction and its duration are programmable. Synchronization of the clamps and AGC to the input signal is possible using the SYNC_IN control pin and setting mode Register CR14 to Logic Level “1.” Using this method, it is possible to ensure that AGC and clamping are only applied outside the active video area. When the clamps are operational, Equation 1 shows how the ADV7202 ensures that the level to which the user is clamping is unaffected by the AGC loop. When no clamps are operational, the operation should be regarded as a straightforward gain-andlevel shift. Control Signals The function and operation of the SYNC_IN signal is described in the Clamp and AGC Control section. The SYNC_OUT will go high while Cr data from a YCrCb data stream or C data from a Y/C data stream has been output on DOUT[9:0] (see Figures 1 to 3). Equation 1 maps the ADC input voltage range to its output. AGC Gain The AGC gain can be set to a value from 0 to 7.99. The AGC Gain Register holds a 12-bit number that corresponds to the required gain. The first three MSBs hold the gain integer value while the remaining nine bits hold the gain fractional value. The new AGC multiplier is latched when the MSB register is written to. Example: The user requires a gain of 3.65. I2C Filter A selectable internal I2C filter allows significant noise reduction on the I2C interface. In setting ALSB high, the input bandwidth on the I2C lines is reduced and pulses of less than 50 ns are not passed to the I2C controller. Setting ALSB low allows greater input bandwidth on the I2C lines. XTAL0 DOUT [9:0] CVBS CVBS CVBS CVBS CVBS CVBS CVBS SYNC_OUT Figure 1. SYNC_OUT Output Timing, CVBS Input XTAL0 DOUT [9:0] Y C Y C Y C SYNC_OUT Figure 2. SYNC_OUT Output Timing, Y/C (S-VIDEO) Input REV. 0 (2) –11– Y ADV7202 XTAL0 DOUT [9:0] CR Y CB Y CR Y CB SYNC_OUT Figure 3. SYNC_OUT Output Timing, YCrCb Input MPU PORT DESCRIPTION A Logic “0” on the LSB of the first byte means that the master will write information to the peripheral. A Logic “1” on the LSB of the first byte means that the master will read information from the peripheral. The ADV7202 supports a 2-wire serial (I2C-compatible) microprocessor bus driving multiple peripherals. Two inputs, serial data (SDA) and serial clock (SCL), carry information between any device connected to the bus. Each slave device is recognized by a unique address. The ADV7202 has four possible slave addresses for both read and write operations. These are unique addresses for each device and are illustrated in Figure 4. The LSB sets either a read or write operation. Logic Level “1” corresponds to a read operation, while Logic Level “0” corresponds to a write operation. A1 is set by setting the ALSB pin of the ADV7202 to Logic Level “0” or Logic Level “1.” When ALSB is set to “0,” there is greater input bandwidth on the I2C lines, which allows high speed data transfers on this bus. When ALSB is set to “1,” there is reduced input bandwidth on the I2C lines, which means that pulses of less than 50 ns will not pass into the I2C internal controller. This mode is recommended for noisy systems. 0 0 1 0 1 1 A1 The ADV7202A acts as a standard slave device on the bus. The data on the SDA pin is eight bits long, supporting the 7-bit addresses plus the R/W bit. It interprets the first byte as the device address and the second byte as the starting subaddress. The subaddresses auto-increment, allowing data to be written to or read from the starting subaddress. A data transfer is always terminated by a Stop condition. The user can access any unique subaddress register one-by-one, without updating all the registers. Stop and Start conditions can be detected at any stage during the data transfer. If these conditions are asserted out of sequence with normal read and write operations, they cause an immediate jump to the idle condition. During a given SCL high period, the user should only issue one Start condition, one Stop condition, or a single Stop condition followed by a single Start condition. If an invalid subaddress is issued by the user, the ADV7202 will not issue an acknowledge and will return to the idle condition. If in auto-increment mode, the user exceeds the highest subaddress, the following action will be taken: X ADDRESS CONTROL SET UP BY ALSB 1. In read mode, the highest subaddress register contents will continue to be output until the master device issues a no-acknowledge. This indicates the end of a read. A no-acknowledge condition is where the SDA line is not pulled low on the ninth pulse. READ/WRITE CONTROL 0 1 DISABLED ENABLED Figure 4. Slave Address To control the various devices on the bus, the following protocol must be followed. First, the master initiates a data transfer by establishing a Start condition, defined by a high-to-low transition on SDA while SCL remains high. This indicates that an address/ data stream will follow. All peripherals respond to the Start condition and shift the next eight bits (7-bit address + R/W bit). The bits are transferred from MSB down to LSB. The peripheral that recognizes the transmitted address responds by pulling the data line low during the ninth clock pulse. This is known as an Acknowledge Bit. All other devices withdraw from the bus at this point and maintain an idle condition. The idle condition is where the device monitors the SDA and SCL lines waiting for the Start condition and the correct transmitted address. The R/W bit determines the direction of the data. 2. In write mode, the data for the invalid byte will not be loaded into any subaddress register, a no-acknowledge will be issued by the ADV7202, and the part will return to the idle condition. Figure 5 illustrates an example of data transfer for a read sequence and the Start and Stop conditions. SDATA SCLOCK –12– S 1–7 8 9 1–7 8 9 START ADDR R/W ACK SUBADDRESS ACK 1–7 DATA 8 9 P ACK STOP Figure 5. Bus Data Transfer REV. 0 ADV7202 WRITE SEQUENCE S SLAVE ADDR A(S) SUB ADDR A(S) DATA LSB = 0 READ SEQUENCE S SLAVE ADDR A(S) S = START BIT P = STOP BIT A(S) DATA A(S) P LSB = 1 SUB ADDR A(S) S SLAVE ADDR A(S) = ACKNOWLEDGE BY SLAVE A(M) = ACKNOWLEDGE BY MASTER A(S) DATA A(M) DATA A(M) P A(S) = NO-ACKNOWLEDGE BY SLAVE A(M) = NO-ACKNOWLEDGE BY MASTER Figure 6. Write and Read Sequence t5 t3 t3 SDA t6 t1 SCL t2 t7 t4 t8 2 Figure 7. I C MPU Port Timing Diagram t 12 DACCLK1 t 10 t10 – CLOCK HIGH TIME t11 – CLOCK LOW TIME t12 – DATA SETUP TIME t13 – DATA HOLD TIME t 13 t 11 DATA [9:0] DACCLK0 DATA DATA Figure 8. Input Data Format Timing Diagram Single Clock t 12 t 12 t 13 DACCLK0 DACCLK1 DAC_DATA[9:0] DATA t 13 t 12 DATA DATA DATA t 13 t 13 t 12 t 11 t 10 Figure 9. Input Data Format Timing Diagram Dual Clock REV. 0 –13– DATA t10 – CLOCK HIGH TIME t11 – CLOCK LOW TIME t12 – DATA SETUP TIME t13 – DATA HOLD TIME ADV7202 DIGITAL DATA INPUT TIMING DIAGRAMS A1 A0 A2 A3 DACCLK1 AT A3, NEW DAC0 DATA IS CLOCKED IN AND A0, A1, AND A2 ARE SENT TO THE DACs. DATA APPEARS AT THE OUTPUT DACs TWO CLOCK CYCLES AFTER BEING SENT TO THE DACs. DACCLK0 DAC_DATA [9:0] DAC0 DAC1 DAC2 DAC0 DAC1 DAC2 DAC0 Figure 10. DAC Mode 1, Single Clock, Single Edge Input Data Format Timing Diagram* *The figure shows three DAC usages. DACCLK0 is a data line that indicates the data is for DAC0. A1 A2 A3 A4 A1 DAC1 DATA CLOCKED IN. DACCLK0 A2 DAC2 DATA CLOCKED IN. A3 DAC3 DATA CLOCKED IN. DACCLK1 DAC_DATA [9:0] DAC1 DAC2 DAC3 DAC0 DAC1 DAC2 DAC3 DAC0 A4 NEW DAC0 DATA IS CLOCKED IN AND A0, A1, A2, AND A3 ARE SENT TO THE DACs. DATA APPEARS AT THE OUTPUT TWO CLOCK CYCLES AFTER BEING SENT TO THE DACs. Figure 11. DAC Mode 2, Dual Clock, Dual Edge Input Data Format Timing Diagram A0 A1 A2 A3 A4 DACCLK1 AT A4, PREVIOUS A0, A2, AND A3 DATA IS SENT TO THE DACs. AT A2, A1 DATA IS SENT TO THE DACs. DATA APPEARS AT THE OUTPUT DACs 2 CLOCK CYCLES AFTER BEING SENT TO THE DACs. DACCLK0 DAC_DATA [9:0] DAC0 DAC1 DAC2 DAC1 DAC0 DAC1 DAC2 Figure 12. DAC Mode 3, 4:2:2 Input Data Format Timing Diagram t 15 t 14 XTAL0 t 15 OUTPUT ADC O/P DOUT[9:0] SYNC_OUT, SYNC_IN DATA DATA t14 – ACCESS TIME t15 – HOLD TIME Figure 13. Digital O/P Timing –14– REV. 0 ADV7202 XTAL0 DOUT [9:0] DATA DATA DATA DATA DATA DATA DATA DATA Figure 14. Standard Mode Digital Data O/P Format REGISTER ACCESS REGISTER PROGRAMMING The MPU can write to or read from all of the registers of the ADV7202 except the Subaddress Registers, which are write-only. The Subaddress Register determines which register the next read or write operation accesses. All communications with the part through the bus start with an access to the Subaddress Register. A read/write operation is then performed from/to the target address which then increments to the next address until a Stop command on the bus is performed. The following section describes the functionality of each register. All registers can be read from as well as written to. Subaddress Register (SR7–SR0) The Communications Register is an 8-bit write-only register. After the part has been accessed over the bus, and a read/write operation is selected, the subaddress is set up. The Subaddress Register determines to/from which register the operation takes place. Figure 15 shows the various operations under the control of the Subaddress Register. “0” should always be written to SR7. Register Select (SR6–SR0) These bits are set up to point to the required starting address. SR7 SR6 SR5 SR3 SR4 SR2 SR1 ADV7202 REGISTER ADDRESS SR6 SR5 SR4 SR3 SR2 SR1 SR0 00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h 16h 17h 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 MODE REGISTER 0 MODE REGISTER 1 MODE REGISTER 2 MODE REGISTER 3 AGC REGISTER 0 AGC REGISTER 1 CLAMP REGISTER 0 CLAMP REGISTER 1 CLAMP REGISTER 2 CLAMP REGISTER 3 TIMING REGISTER VREF ADJUST REGISTER RESERVED RESERVED RESERVED RESERVED AUX REGISTER 0 AUX REGISTER 1 AUX REGISTER 2 AUX REGISTER 3 AUX REGISTER 4 AUX REGISTER 5 AUX REGISTER 6 AUX REGISTER 7 Figure 15. Subaddress Registers REV. 0 –15– SR0 ADV7202 MODE REGISTER 0 MR0 (MR07–MR00) (Address (SR4–SR0) = 00H) External Reference Enable (MR01) Setting this bit to “1” enables an external voltage reference for the ADC. Figure 16 shows the various operations under the control of Mode Register 0. Voltage Reference Power-Down (MR02) Setting this bit to “1” causes the internal DAC voltage reference to power down. MR0 BIT DESCRIPTION ADC Reference Voltage (MR00) ADC Power-Down (MR03) This control bit is used to select the ADC reference voltage. When this bit is set to “0,” a reference voltage of 1.1 V is selected. When the bit is set to “1,” a reference voltage of 2.2 V is selected. Setting this bit to “1” causes the video rate ADC to power down. Power-Down (MR04) Setting this bit to “1” puts the device into power-down mode. Reserved (MR05–MR07) Zero must be written to these bits. MR07 MR06 MR05 MR04 MR03 MR02 ADC REF VOLTAGE VREF POWER-DOWN POWER-DOWN MR00 MR02 MR04 0 1 MR00 MR01 0 1 NORMAL POWER-DOWN ADC POWER-DOWN MR07–MR05 0 1 1.1V 2.2V EXT REF ENABLE MR03 ZERO MUST BE WRITTEN TO THESE BITS 0 1 NORMAL POWER-DOWN MR01 NORMAL POWER-DOWN 0 1 INTERNAL EXTERNAL Figure 16. Mode Register 0 Dual Edge Clock (MR14) MODE REGISTER 1 MR1 (MR17–MR10) (Address (SR4–SR0) = 01H) Setting this bit to “1” allows data to be read into the DACs on both edges of the clock; hence, data may be read in at twice the clock frequency. See Figure 17. If this bit is set to “0,” the data will only be strobed on the rising edge of the clock. Figure 17 shows the various operations under the control of Mode Register 1. Dual Clock (MR15) MR1 BIT DESCRIPTION DAC0 Control (MR10) Setting this bit to “0” enables DAC0; otherwise, this DAC is powered down. Setting this bit to “1” allows the use of two clocks to strobe data into the DACs. See Figure 17. It is possible to clock data in with only one clock and use the second clock to contain timing information. DAC1 Control (MR11) 4:2:2 Mode (MR16) Setting this bit to “0” enables DAC1; otherwise, this DAC is powered down. Setting this bit to “1” enables data to be input in 4:2:2 format. 4:2:2 mode will only work if MR14 and MR15 register bits are set to zero. DAC2 Control (MR12) Setting this bit to “0” enables DAC2; otherwise, this DAC is powered down. DAC Input Invert (MR17) Setting this bit to “1” causes the input data to the DACs to be inverted allowing for an external inverting amplifier. DAC3 Control (MR13) Setting this bit to “0” enables DAC3; otherwise, this DAC is powered down. MR17 MR16 MR15 DAC I/P INVERT MR13 DISABLE ENABLE 0 1 4:2:2 MODE MR16 SINGLE EDGE DUAL EDGE 0 1 DUAL CLOCK 0 1 DAC0 CONTROL MR12 MR15 DISABLE ENABLE MR10 MR11 DAC2 CONTROL MR14 0 1 MR12 DUAL EDGE CLOCK MR17 0 1 MR14 MR10 NORMAL POWER-DOWN DAC3 CONTROL MR13 SINGLE CLK DUAL CLK 0 1 0 1 NORMAL POWER-DOWN DAC1 CONTROL MR11 NORMAL POWER-DOWN 0 1 NORMAL POWER-DOWN Figure 17. Mode Register 1 –16– REV. 0 ADV7202 MODE REGISTER 2 MR2 (MR20–MR27) (Address (SR4–SR0) = 02H) SHA1 Control (MR25) Figure 18 shows the various operations under the control of Mode Register 2. SHA2 Control (MR26) Setting this bit to “0” enables SHA1; otherwise, this SHA is powered down. Setting this bit to “0” enables SHA2; otherwise, this SHA is powered down. MR2 BIT DESCRIPTION Analog Input Configuration (MR20–MR23) AUX Control (MR27) This control selects the analog input configuration, up to five CVBS input channels, or two component YUV, or three S-Video and eight auxiliary inputs. See Figure 18 for details. Setting this bit to “0” enables the auxiliary ADC; otherwise, Aux ADC is powered down. SHA0 Control (MR24) Setting this bit to “0” enables SHA0; otherwise, this SHA is powered down (SHA = Sample and Hold Amplifier). MR27 MR26 MR25 AUX CONTROL MR24 MR23 MR22 SHA0 CONTROL MR27 ANALOG INPUT CONFIGURATION MR24 0 1 NORMAL POWER-DOWN 0 1 SHA2 CONTROL NORMAL POWER-DOWN MR23 MR22 MR21 MR20 0 0 0 0 0 0 0 0 1 1 1 SHA1 CONTROL MR26 0 1 MR20 MR21 MR25 NORMAL POWER-DOWN 0 1 NORMAL POWER-DOWN 0 0 0 0 1 1 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 CVBS IN ON AIN1 CVBS IN ON AIN2 CVBS IN ON AIN3 RESERVED CVBS IN ON AIN5 CVBS IN ON AIN6 Y/C IN ON AIN1, AIN4 Y/C IN ON AIN2, AIN3 YUV IN ON AIN2, AIN3, AIN6 CVBS IN ON AIN1, 8 AUX INPUTS CVBS IN ON AIN2, 8 AUX INPUTS Figure 18. Mode Register 2 MODE REGISTER 3 MR3 (MR30–MR37) (Address (SR4–SR0) = 03H) Voltage Clamp (MR33) Figure 19 shows the various operations under the control of Mode Register 3. Setting this bit to “1” puts the digital outputs into high impedance. Setting this bit to “1” will enable the voltage clamps. Output Enable (MR34) MR3 BIT DESCRIPTION Clamp Current (MR30) SYNC Polarity (MR35) Setting this bit to “1” enables differential mode for the analog inputs; otherwise, the inputs are single-ended. See Figure 19. This bit controls the polarity of the SYNC_IN pin. If the bit is set to “0,” a logic low pulse corresponds to H-Sync. If the bit is “1,” a logic high pulse corresponds to H-Sync. This sync in pulse can then be used to control the synchronization of AGC/Clamping. See AR12. SHA Gain (MR32) Reserved (MR36–MR37) Setting this bit to “0” enables SHA gain of 1. If the bit is set to “1,” the SHA gain is 2. The SHA gain will limit the input signal range. See Figure 19. Zero must be written to both these registers. Setting this bit to “1” enables the halving of all clamp currents. Analog Input Mode (MR31) MR37 MR36 MR35 MR37–MR36 MR34 MR33 MR32 OUTPUT ENABLE SHA GAIN MR34 ZERO MUST BE WRITTEN TO THESE REGISTERS 0 1 NORMAL HIGH Z 0 1 SYNC POLARITY MR30 1 2 LOW HIGH 0 1 VOLTAGE CLAMP MR33 0 1 –17– NORMAL HALF ANALOG INPUT MR31 OFF ON Figure 19. Mode Register 3 REV. 0 CLAMP CURRENT MR32 MR35 0 1 MR30 MR31 0 1 SINGLE-ENDED DIFFERENTIAL ADV7202 AGC REGISTER 0 AR0 (AR00–AR07) (Address (SR4–SR0) = 04H) AGC REGISTER 1 AR1 (AR08–AR15) (Address (SR4–SR0) = 05H) Figure 20 shows the various operations under the control of AGC Register 0. Figure 20 shows the various operations under the control of AGC Register 1. AR0 BIT DESCRIPTION AGC Multiplier (AR00–AR07) AR1 BIT DESCRIPTION AGC Multiplier (AR08–AR11) This register holds the last eight bits of the 12-bit AGC multiplier word. These registers hold the first four bits of the 12-bit AGC multiplier word. AGC Sync Enable (AR12) Setting this bit to “1” forces the AGC to wait until the next sync pulse before switching on. Reserved (AR13–AR15) Zero must be written to these registers. AR07 AR15 AR14 AR13 AR12 AR11 AR05 AR10 AR04 AR03 AR09 AGC SYNC ENABLE AR15–AR13 ZERO MUST BE WRITTEN TO THESE REGISTERS AR06 AR01 AR00 AR08 AGC MULTIPLIER AR12 0 1 AR02 AR11–AR00 OFF ON 12-BIT AGC MULTIPLIER AR00, HOLDS THE LSB, AR11 THE MSB Figure 20. AGC Registers 0–1 –18– REV. 0 ADV7202 CLAMP REGISTER 0 CR1 BIT DESCRIPTION Fine Clamp On Time (CR10–CR12) CR0 (CR00–CR07) There are three fine clamp circuits on the chip. This word controls the number of clock cycles for which the fine clamps are switched on per video line. The clamp is switched on after a SYNC pulse is received on the SYNC_IN pin, provided the relevant enabling bit is set (see CR16). (Address (SR4–SR0) = 06H) Figure 21 shows the various operations under the control of Clamp Register 0. CR0 BIT DESCRIPTION Clamp Level/16 (CR00–CR06) To perform an accurate AGC gain operation, it is necessary to know to what level the user is clamping the black level. This black level is then subtracted from the 10-bit ADC output before gaining. It is then added on again afterwards. It should be noted that this register is seven bit and will hold the value of Clamp Value/16. Coarse Clamp On Time (CR13–CR15) Reserved (CR07) Synchronize Clamps (CR16) Zero must be written to this bit. Setting this bit to “1” forces the clamps to wait until the next sync pulse before switching on. There are three coarse clamp circuits on the chip. This I2C word controls the number of clock cycles for which the fine clamps are switched on per video line. The clamp is switched on after a SYNC pulse is received on the SYNC_IN pin, provided the relevant enabling bit is set (see CR16). CLAMP REGISTER 1 CR1 (CR10–CR17) (Address (SR4–SR0) = 07H) Reserved (CR17) Zero must be written to this bit. Figure 22 shows the various operations under the control of Clamp Register 1. CR07 CR06 CR05 CR07 CR04 CR03 CR02 CR01 CR00 CLAMP LEVEL ZERO MUST BE WRITTEN TO THIS BIT CR06–CR00 7-BIT [6:0] CLAMP LEVEL, CR00 HOLDS THE LSB, CR06 THE MSB Figure 21. Clamp Register 0 CR17 CR16 CR17 ZERO MUST BE WRITTEN TO THIS BIT SYNCHRONIZE CLAMPS CR16 0 1 OFF ON CR15 CR14 CR13 CR12 COARSE CLAMP ON TIME CR15 CR14 CR13 FINE CLAMP ON TIME CR12 CR11 CR10 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 2 CLOCK CYCLES 4 CLOCK CYCLES 8 CLOCK CYCLES 16 CLOCK CYCLES 32 CLOCK CYCLES 64 CLOCK CYCLES 128 CLOCK CYCLES 256 CLOCK CYCLES Figure 22. Clamp Register 1 REV. 0 CR10 CR11 –19– 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 2 CLOCK CYCLES 4 CLOCK CYCLES 8 CLOCK CYCLES 16 CLOCK CYCLES 32 CLOCK CYCLES 64 CLOCK CYCLES 128 CLOCK CYCLES 256 CLOCK CYCLES ADV7202 CLAMP REGISTER 2 CR2 (CR20–CR27) (Address (SR4–SR0) = 08H) Fine Clamp 1 ON/OFF (CR23) Figure 23 shows the various operations under the control of Clamp Register 2. Fine Clamp 2 Up/Down (CR24) This bit switches fine clamp number 1 on for the prescribed number of clock cycles (CR10–CR12). This bit controls the direction of fine clamp number 2, valid only if the clamp is enabled. CR2 BIT DESCRIPTION Fine Clamp 0 Up/Down (CR20) Fine Clamp 2 ON/OFF (CR25) This bit controls the direction of fine clamp number 0, valid only if the clamp is enabled. This bit switches fine clamp number 2 on for the prescribed number of clock cycles (CR10–CR12). Fine Clamp 0 ON/OFF (CR21) Reserved (CR26–CR27) This bit switches fine clamp number 0 on for the prescribed number of clock cycles (CR10–CR12). Zero must be written to these registers. Fine Clamp 1 Up/Down (CR22) This bit controls the direction of fine clamp number 1, valid only if the clamp is enabled. CR27 CR26 CR25 CR24 CR23 FINE CLAMP 2 UP/DOWN CR27–CR26 0 1 CR22 DOWN UP 0 1 CR20 CR21 FINE CLAMP 1 UP/DOWN CR24 ZERO MUST BE WRITTEN TO THESE REGISTERS CR22 FINE CLAMP 0 UP/DOWN CR20 DOWN UP 0 1 FINE CLAMP 2 ON/OFF FINE CLAMP 1 ON/OFF FINE CLAMP 0 ON/OFF CR25 CR23 CR21 0 1 OFF ON 0 1 OFF ON 0 1 DOWN UP OFF ON Figure 23. Clamp Register 2 CLAMP REGISTER 3 CR3 (CR30–CR37) (Address (SR4–SR0) = 09H) Coarse Clamp 1 Up/Down (CR32) Figure 24 shows the various operations under the control of Clamp Register 3. Coarse Clamp 1 ON/OFF (CR33) This bit controls the direction of coarse clamp number 1, valid only if the clamp is enabled. This bit switches coarse clamp number 1 on for the prescribed number of clock cycles (CR13–CR15). CR3 BIT DESCRIPTION Coarse Clamp 0 Up/Down (CR30) Coarse Clamp 2 Up/Down (CR34) This bit controls the direction of coarse clamp number 0, valid only if the clamp is enabled. This bit controls the direction of coarse clamp number 2, valid only if the clamp is enabled. Coarse Clamp 0 ON/OFF (CR31) Coarse Clamp 2 ON/OFF (CR35) This bit switches coarse clamp number 0 on for the prescribed number of clock cycles (CR13–CR15). This bit switches coarse clamp number 2 on for the prescribed number of clock cycles (CR13–CR15). Reserved (CR36–CR37) Zero must be written to these registers. CR36 CR37 CR35 CR34 CR33 COARSE CLAMP 2 UP/DOWN CR37–CR36 ZERO MUST BE WRITTEN TO THESE REGISTERS COARSE CLAMP 0 UP/DOWN CR32 DOWN UP 0 1 CR30 CR31 COARSE CLAMP 1 UP/DOWN CR34 0 1 CR32 CR30 DOWN UP 0 1 DOWN UP COARSE CLAMP 2 ON/OFF COARSE CLAMP 1 ON/OFF COARSE CLAMP 0 ON/OFF CR35 CR33 CR31 0 1 OFF ON 0 1 OFF ON 0 1 OFF ON Figure 24. Clamp Register 3 –20– REV. 0 ADV7202 TIMING REGISTER TR (TR00–TR07) (Address (SR4–SR0) = 0AH) Duty Cycle Equalizer (TR03) When this bit is set to “1,” the clock duty cycle equalizer circuit is active. This will only have an effect on the ADC operation. The digital core clock will not be affected. Figure 25 shows the various operations under the control of the Timing Register. Clock Delay (TR05–TR06) Using these two bits, it is possible to insert a delay in the clock signal to the digital core. These bits control the insertion of the delay. TR BIT DESCRIPTION Crystal Oscillator Circuit (TR00) If this bit is set to “0,” the internal oscillator circuit will be disabled. Disabling the oscillator circuit is possible when an external clock module is used, thus saving power. Reserved (TR02, TR04, TR07) Zero must be written to the bits in these registers. ADC Bias Currents (TR01) If this bit is set to “1,” all analog bias currents will be doubled. TR07 TR06 TR05 TR04 TR02 TR03 CRYSTAL OSCILLATOR CIRCUIT TR07 TR04 TR02 ZERO MUST BE WRITTEN TO THIS BIT ZERO MUST BE WRITTEN TO THIS BIT ZERO MUST BE WRITTEN TO THIS BIT DUTY CYCLE EQUALIZER CLOCK DELAY TR06 TR05 0 0 1 1 0 1 0 1 TR03 0ns 4ns 6ns 8ns 0 1 TR00 TR01 TR00 0 1 DISABLE ENABLE ADC BIAS CURRENTS TR01 INACTIVE ACTIVE 0 1 NORMAL DOUBLE Figure 25. Timing Register 0 VREF ADJUST REGISTER VR (VR00–VR07) (Address (SR4–SR0) = 0BH) ADC Reference Voltage Adjust (VR04–VR06) Figure 26 shows the various operations under the control of the VREF Adjust Register. Reserved (VR07) By setting the value of this 3-bit word, it is possible to trim the ADC internal voltage reference VREFADC. Zero must be written to this register. VR BIT DESCRIPTION Reserved (VR00) This register is reserved and “1” must be written to this bit. Reserved (VR01–VR03) Zero must be written to these registers. VR07 VR06 VR05 VR03 VR04 VR07 VR02 VR03–VR01 ZERO MUST BE WRITTEN TO THIS BIT ZERO MUST BE WRITTEN TO THESE BITS ADC REFERENCE VOLTAGE ADJUST VR06 VR05 VR04 0 0 0 0 1 1 1 1 0 1 0 1 0 1 0 1 0 0 1 1 0 0 1 1 DEFAULT NOMINAL +14mV +28mV +42mV –14mV –28mV –42mV –56mV Figure 26. ADC VREF Register REV. 0 –21– VR01 VR00 VR00 ONE MUST BE WRITTEN TO THIS BIT ADV7202 AUXILIARY MONITORING REGISTERS AU (AU00–AU07) (Address (SR4–SR0) = 10H) There are eight Auxiliary Monitoring Registers. These registers are read-only; when the device is configured for auxiliary inputs, AU07 AU06 AU05 AU04 they will display a value corresponding to the converted auxiliary input. Auxiliary Register 0 will contain the value of the converted auxiliary 0 input, Auxiliary Register 1 the value of the converted auxiliary 1 input, and so on to Auxiliary Register 7. AU03 AU02 AU01 AU00 AU09 AU08 AU17 AU16 AU25 AU24 AUX REGISTER 0 AU07–AU00 8-BIT [7:0] VALUE CORRESPONDING TO AUX0 INPUT VALUE Figure 27. AUX Register 0 AU15 AU14 AU13 AU12 AU11 AU10 AUX REGISTER 1 AU15–AU08 8-BIT [7:0] VALUE CORRESPONDING TO AUX1 INPUT VALUE Figure 28. AUX Register 1 AU23 AU22 AU21 AU20 AU19 AU18 AUX REGISTER 2 AU23–AU16 8-BIT [7:0] VALUE CORRESPONDING TO AUX2 INPUT VALUE Figure 29. AUX Register 2 AU31 AU30 AU29 AU28 AU27 AU26 AUX REGISTER 3 AU31–AU24 8-BIT [7:0] VALUE CORRESPONDING TO AUX3 INPUT VALUE Figure 30. AUX Register 3 –22– REV. 0 ADV7202 AU39 AU38 AU37 AU36 AU35 AU34 AU33 AU32 AU41 AU40 AU49 AU48 AU57 AU56 AUX REGISTER 4 AU39–AU32 8-BIT [7:0] VALUE CORRESPONDING TO AUX4 INPUT VALUE Figure 31. AUX Register 4 AU47 AU46 AU45 AU44 AU43 AU42 AUX REGISTER 5 AU47–AU40 8-BIT [7:0] VALUE CORRESPONDING TO AUX5 INPUT VALUE Figure 32. AUX Register 5 AU55 AU54 AU53 AU52 AU51 AU50 AUX REGISTER 6 AU55–AU48 8-BIT [7:0] VALUE CORRESPONDING TO AUX6 INPUT VALUE Figure 33. AUX Register 6 AU63 AU62 AU61 AU60 AU59 AU58 AUX REGISTER 7 AU63–AU56 8-BIT [7:0] VALUE CORRESPONDING TO AUX7 INPUT VALUE Figure 34. AUX Register 7 REV. 0 –23– ADV7202 CLAMP CONTROL The clamp control has two modes of operation, if the synchronize clamp control bit CR16 (Bit-6 address 07h) is set, then the clamps that are enabled will be switched on for the programmed time when triggered by the Sync_IN control signal, this control signal is edge detected and its polarity can be set by MR35 (Bit 5 Address 03h). If the synchronize clamp control bit is set to zero, when enabled each clamp will switch on for the programmed time. The clamp control bits are edge detected and the bits must first be reset to zero before the clamps can be switched on again. DAC TERMINATION AND LAYOUT CONSIDERATIONS Resistor RSET is connected between the RSET pin and AVSS and is used to control the amplitude of the DAC output current. I MAX = 5.196 RSET Amps (3) Therefore, a recommended RSET value of 1200 Ω will enable an IMAX of 4.43 mA. VMAX = RLOAD × IMAX, RLOAD should have a value of 300 Ω. The ADV7202 has four analog outputs—DAC0, DAC1, DAC2, and DAC3. For cable driving the DACs should be used with an external buffer. Suitable op amps are the AD8057 or AD8061. PC BOARD LAYOUT CONSIDERATIONS Power planes should encompass a digital power plane (DVDD) and an analog power plane (AVDD). The analog power plane should contain the ADCs and all associated circuitry, including VREF circuitry. The digital power plane should contain all logic circuitry. The analog and digital power planes should be individually connected to the common power plane at one single point through a suitable filtering device such as a ferrite bead. DAC output traces on a PCB should be treated as transmission lines. It is recommended that the DACs be placed as close as possible to the output connector, with the analog output traces being as short as possible (less than three inches). The DAC termination resistors should be placed as close as possible to the DAC outputs and should overlay the PCB’s ground plane. As well as minimizing reflections, short analog output traces will reduce noise pickup due to neighboring digital circuitry. Supply Decoupling Noise on the analog power plane can be further reduced by the use of decoupling capacitors. Optimum performance is achieved by the use of 0.1 µF ceramic capacitors. Each of the group of AVDD or DVDD pins should be individually decoupled to ground. This should be done by placing the capacitors as close as possible to the device with the capacitor leads as short as possible, thus minimizing lead inductance. The ADV7202 is optimally designed for the lowest noise performance, both radiated and conducted noise. To complement the excellent noise performance of the ADV7202, it is imperative that great care be given to the PC board layout. Digital Signal Interconnect The layout should be optimized for lowest noise on the ADV7202 power and ground lines. This can be achieved by shielding the digital inputs and providing good decoupling. The lead length between groups of AVDD, AVSS, DVDD, and DVSS pins should be kept as short as possible to minimize inductive ringing. Due to the high clock rates used, long clock lines to the ADV7202 should be avoided to minimize noise pickup. It is recommended that a four-layer printed circuit board be used, with power and ground planes separating the layer of the signal carrying traces of the components and solder side layer. Placement of components should be considered to separate noisy circuits, such as crystal clocks, high speed logic circuitry, and analog circuitry. Analog Signal Interconnect There should be separate analog and digital ground planes (AVSS and DVSS). The digital signal lines should be isolated as much as possible from the analog outputs and other analog circuitry. Digital signal lines should not overlay the analog power plane. Any active pull-up termination resistors for the digital inputs should be connected to the digital power plane and not the analog power plane. The ADV7202 should be located as close as possible to the output connectors, thus minimizing noise pickup and reflections due to impedance mismatch. For optimum performance, the analog outputs should each be source and load terminated, as shown in Figure 35. The termination resistors should be as close as possible to the ADV7202 to minimize reflections. Any unused inputs should be tied to the ground. –24– REV. 0 ADV7202 POWER SUPPLY DECOUPLING FOR EACH POWER SUPPLY GROUP AVDD 0.1F 10F AVDD DVDD DVDD 0.1F 0.1F 10F 6, 42 54 46 45 COMP 0.1F VREFDAC AVDD DVDD AIN1–AIN6 DAC0 44 300⍀ DOUT[9:0] DAC1 43 DAC_DATA[9:0] 300⍀ 0.1F UNUSED INPUTS SHOULD BE GROUNDED ⴙ 10F 0.1F 24 CAP1 DAC2 40 300⍀ 23 CAP2 ADV7202 DAC3 39 DVDD 300⍀ 4.7k⍀ 3 ALSB SCL DVDD 5k⍀ MPU BUS SDA 64 48 RESET CML 22 4.7F 6.3V 27MHz CLOCK OSDEN 25 4.7k⍀ 0.1F REFADC 21 4 XTAL0 DVDD AVSS DVSS 7, 41 10F RSET 47 53, 20 1.2k⍀ Figure 35. Suggested Schematic REV. 0 5k⍀ 2 100⍀ 4.7k⍀ ⴙ DVDD DVDD 100⍀ –25– 0.1F ADV7202 OUTLINE DIMENSIONS 64-Lead Plastic Quad Flatpack [LQFP] (ST-64B) Dimensions shown in millimeters 0.75 0.60 0.45 12.00 BSC 1.60 MAX 64 49 1 48 SEATING PLANE TOP VIEW 10.00 BSC (PINS DOWN) 1.45 1.40 1.35 0.15 0.05 0.20 0.09 SEATING PLANE 7ⴗ 3.5ⴗ 0ⴗ 0.08 MAX COPLANARITY VIEW A 16 33 32 17 0.50 BSC VIEW A ROTATED 90ⴗ CCW 0.27 0.22 0.17 COMPLIANT TO JEDEC STANDARDS MS-026BCD –26– REV. 0 –27– –28– PRINTED IN U.S.A. C02602–0–10/02(0)