Shanghai Lunsure Electronic Technology Co.,Ltd Tel:0086-21-37185008 Fax:0086-21-57152769 MR2400FR MR2410FR Features • • • • • • Glass Passivated Die Low Forward Voltage Drop High Current Capability High Surge Current Low Leakage Anode To Tab Configuration 24 Amp Rectifier Maximum Ratings • • • , )- ' "65°/150° ) - ' "65°/!.° Thermal Resistance Juncetion to Case (R C /W Ojc):0.8 °C 5'6 %' 0 ' (0 7 8 ) %' 08 ) %'9 * () 8 ) MR2400FR 50V 35V 50V MR2401FR 100V 70V 100V MR2402FR 200V 140V 200V MR2404FR 400V 280V 400V MR2406FR 600V 420V 600V MR2408FR 800V 560V 800V MR2410FR 1000V 700V 1000V Electrical Characteristics @ 25°C Unless Otherwise Specified Average Forward Current Peak Forward Surge Current Maximum Instantaneous Forward Voltage Maximum DC Reverse Current At Rated DC Blocking Voltage Maximum Reverse Recovery Time Typical Junction Capacitance IF(AV) 24.0A Tc =125°C IFSM 300A 8.3ms, half sine DIMENSIONS INCHES VF 1.15V IFM = 24.0A; Ta= 25°C* IR 25µA 1.0µA Tc = 25°C Tc = 100°C Trr 100ns to. 250ns. 95pF IF=0.5A, IR=1.0A, Irr=0.25A Measured at 1.0MHz, VR=4.0V CJ *Pulse test: Pulse width 300 µsec, Duty cycle 1% ! " www.cnelectr.com M M FR2400FR thru FR2410FR Figure 1 Typical Forward Characteristics 20 Figure 2 Forward Derating Curve 10 30 6 Amps 4 25 2 20 1 15 6 Amps 4 10 2 5 25°C Single Phase, Half Wave 60Hz Resistive or Inductive Load 1 .5 0 25 0 50 .4 100 125 150 °C Average Forward Rectified Current - Amperesversus Ambient Temperature - °C .2 .1 75 .6 .8 1.0 1.2 1.4 1.6 Volts Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts Figure 3 Maximum Non-Repetitive Forward Surge Current 300 250 200 150 Amps 100 50 0 1 2 4 6 8 10 20 40 00 60 80 100 Cycles Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles www.cnelectr.com FR2400FR thr FR2410FR Figure 4 Typical Reverse Characteristics 100 60 40 20 10 6 4 TA=100°C 2 µAmps 1 .6 .4 .2 .1 TA=25°C .06 .04 .02 .01 2 4 80 80 10 12 14 Volts Instantaneous Reverse Leakage Current - MicroAmperesversus Percent Of Rated Peak Reverse Voltage - Volts Reverse Recovery Time Characteristic And Test Circuit Diagram 50Ω 10Ω trr +0.5A 0 25Vdc 1Ω Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive Oscilloscope Note 1 Pulse Generator Note 2 -0.25 -1.0 1cm Set Time Base for 20/100ns/cm www.cnelectr.com