Video ICs Single chip Hi-Fi audio signal processor BH7800K The BH7800K incorporates the functions for a VHS audio signal processing system on a single chip. The circuits on the chip are a peak-noise reduction processor (PNR), an FM modulator / demodulator circuit, an I / O switcher, an automatic FM detector circuit, an FM bandpass filter, and a regulator circuit. Applications •VCRs •1)Features Operates off dual ± power supply which allows a large reduction in the number of coupling capacitors required. A built-in regulator makes it easy to construct a power supply system. 2) A two-line SSB (Synchronized Serial Bus) control decoder circuit is provided, allowing the various IC modes to be set using serial control. 3) A four line input switcher is included (tuner, BS, and line 1 / 2). The output switcher can switch between STEREO, LEFT, and RIGHT, and Hi-Fi, MIX, and NORMAL, and a BS MONITOR function is also provided. 4) The PNR processor and FM modulator / demodulator circuit have reversed characteristics at recording and playback. In addition, the adjustment for carrier frequency and FM deviation / playback level are common. 5) The built-in bandpass filter excels at attenuation of other channels, and can be directly coupled to the playback amplifier. The FM recording output block has a high-performance low-pass filter to produce sine wave output. 6) Slope-control-type FM-switching-noise compensation circuit. 7) Envelope detector circuit and noise-detector-type automatic FM detector circuit. 8) VCO that uses the color signal sub-carrier frequency fSC (NTSC: 3.59545MHz, PAL: 4.433619MHz) and auto-adjusting BPF circuit ensure stable adjustment with no fluctuation due to mounting stress or time. •Absolute maximum ratings (Ta = 25°) Parameter Applied voltage Symbol Limits Unit VCC 18, 36pin ··························· 6.0 V VEE 39pin ······························ – 6.0 V VIN 5, 6, 32pin ························ 6.5 V VIN Pins other than the above ··· 6.0 V Pd 850∗ mW Operating temperature Topr – 10 ~ + 70 °C Storage temperature Tstg – 55 ~ + 125 °C Power dissipation ∗ Reduced by 8.5mW for each increase in Ta of 1°C over 25°C when mounted on a 70mm × 70mm, t = 1.6mm glass epoxy board. 1 Video ICs BH7800K LINE2 R IN MUTE CTRL NORMAL OUT LINE L OUT LINE R OUT MIX OUT MIX ALC NORMAL IN NR TC R WTNG R NR EMPH R •Block diagram 33 32 31 30 29 28 27 26 25 24 23 MIX AMP LINE2 L IN 34 22 DC FB R PNR 21 FM REC OUT VREFP 35 FM OUT SW MODEM VCC 36 ERP 37 20 AUDIO HEAD SW PULSE IN AMP LINE 19 FM ALC LINE AMP D.O COM. GND 38 18 VCCM REG VEE 39 LINE1 R IN 40 17 VCO FO ADJ VCO BPF AUTO ADJUST OUTPUT SWITCH FM BPF 16 BPF ADJ LINE1 L IN 41 15 GNDM ERM 42 ALC ENVE LOPE MODEM INPUT BS R IN 43 ENVE OUT / ADJ FLAG / Hi-Fi DET 13 FM PB IN SWITCH DATA DECODER PNR 1 2 3 4 5 6 7 8 9 10 11 TUNER L IN TUNER M IN HiFi ALC SCL SDA GNDD FSC IN NR TC L WTNG L NR EMPH L 12 DC FB L TUNER R IN BS L IN 44 2 14 Hi-Fi DET Video ICs BH7800K •Pin descriptions Pin No. Pin name 2, 1, 3 TUNER IN L, R, M Tuner input (L, R, M) Function Voltage 0.0V Format 150kΩ 4 Hi-Fi ALC ALC time constant setting for Hi-Fi audio 0.0V EF (NPN) ~ 200Ω 5 SCL CLOCK input for SSB control — B (PNP) 6 SDA DATA input for SSB bus control — B (PNP) 7 GNDD GND for serial control — — 8 FSC IN fSC input for VCO and BPF adjustment 0.0V 200kΩ 9, 25 NR TC L, R PNR attack and recovery time setting Attack R: 530Ω, Recovery R: 6.5kΩ – 5.0V — 10, 24 WTNG L, R Waiting characteristic, treble time constant (external C = 0.0047µF) 0.0V — 11, 23 NR EMPH L, R NR emphasis time constant setting (External C = 0.0047µF) 0.0V — 12, 22 DC FB L, R PNR operating reference potential point 0.0V 23kΩ 13 FM PB IN Playback FM input 1320mVP-P Typ. Input coupling capacitor (GND ~ VCC) 0.0V 100kΩ 14 ENVE OUT / ADJ FLAG / Hi-Fi DET FM Lch signal component envelope output / Hi-Fi DET output / ADJ FLAG output for ADJ EE: 0.8V PB: 1.0V EE: 50kΩ PB, ADJ: EF (NPN) 15 GNDM GND for PNR, MODEM and BPF 0.0V — 16 BPF f0 ADJ Center frequency adjustment for FM BPF 1.9V EF (NPN) ~ 200Ω 17 VCO f0 ADJ VCO control current setting 2.5V EF (NPN) 18 VCCM VCC for MODEM and BPF 5.0V — 19 FM ALC FM ALC time constant setting 0.0V EF (NPN) ~ 2.5kΩ 20 AHSWP IN Audio head switching pulse input — B (PNP) 21 FM REC OUT EE: recording FM output , sine wave output PB: FM BPF output monitor 3.3V EF (NPN) ~ 200Ω 26 NORMAL IN Normal input 0.0V 100kΩ MIX ALC ALC time constant setting for mixer amplifier Attack and recovery time setting 27 28 – 5.0V EF (NPN) ~ 500Ω MIX OUT Mixer amplifier output for RF converter 0.0V 30, 29 LINE L, R OUT Line output 0.0V 330Ω 31 NORMAL OUT Normal output 0.0V EF (P-P) 32 EF (NPN) MUTE CTRL Line output mute control input — 3kΩ ( > 2.5V) LINE2 L, R IN Line2 input (L, R) 0.0V 150kΩ 35 VREFP VCC / 2 reference voltage (power on detect and pre-charge functions) 2.5V 10kΩ 36 VCC VCC regulator 5.0V — 37 ERP VCC regulator error output 5.0V C (NPN) 38 GND I / O switch GND 39 VEE VEE regulator 34, 33 41, 40 42 44, 43 LINE1 IN L, R LINE1 input (L, R) ERM VEE regulator error output BS IN L, R BS input (L, R) 0.0V — – 5.0V — 0.0V – 5.0V 0.0V 150kΩ C (PNP) 150kΩ Note: EF: emitter follower, P-P: push pull, B: base, and C: collector. All numerical values are standardized values. 3 Video ICs BH7800K •Input / output circuits TUNER L / R / M IN (2, 1, 3pin) BS L / R IN (44, 43pin) LINE1 L / R IN (41, 40pin) LINE2 L / R IN (34, 33pin) VCC – 2.0V (2, 3, 33, 34, 40, 41, 43, 44pin) 3k 1 2.0V 150k VEE GND LINE L / R OUT (30, 29pin) MIX OUT (28pin) VCC VCC 200 50 28 25k (29pin) 330 5k 200 30 26k 47k 11.56k 50 30k VEE VEE GND GND FM REC OUT (21pin) FM PB IN (13pin) VCC VCC 200 3.5V 200 25k 25k 20p 2k 21 13 PB 3p 4 8k 12.5k 100k VEE VEE GND GND Video ICs BH7800K AHSWP IN (20pin) ENVE OUT / ADJ FLAG / Hi-Fi DET (14pin) VCC VCC PB 200 42.5k 30k 5k 14 20 50k VEE VEE GND GND SCL (5pin) SDA (6pin) FSC IN (8pin) VCC VCC 2k 8 30k 5 (6pin) 100k 3V 50k 100k VEE VEE GND MUTE CTRL (32pin) 32 VCC 2.5V 51k 10k 2k 200 16k 50k 10k VEE GND 5 Video ICs BH7800K •Electrical characteristics (unless otherwise noted, Ta = 25°, UNREG – Vcc = + 10V, UNREG – V • Output switch control (W1bit5, W1bit4, W1bit3) • BS L2 Through / LINE MUTE control (W1bit2, W1bit1) • LINE AMP gain control (W1bit7, W1bit6) • FM output cotrol (W5bit5) • FM OUT switch control (W2bit4, W2bit3, W2bit2) • NTSC / PAL control (W2bit0) • Recording MUTE (W2bit1) • Hi-Fi MUTE (W1bit0) • Normal input switch control (W3bit4, W3bit3) • Hi-Fi ALC control (W3bit0) • ENVELOPE GAIN (Typ. / + 4dB / + 6dB) control (W4bit4, W4bit3) ) • FM detector level control (W4bit7, W4bit6) • ENVE characteristic control (W4bit5) • DAC TEST control (W4bit2) • MUTE control (pin 32) Signal frequency f = 1kHz • INPUT condition 1: TU / BS / LINE1 / LINE2 VIN = – 20dBV • INPUT condition 2: TU / BS / LINE1 / LINE2 VIN = – 9.8dBV • INPUT condition 3: TU / BS / LINE1 / LINE2 VIN = – 5.0dBV MODEM carrier frequency NTSC Lch 1.30MHz MODEM carrier frequency NTSC Rch 1.70MHz MODEM carrier frequency PAL Lch 1.40MHz MODEM carrier frequency PAL Rch 1.80MHz fsc NTSC 3.579545MHz fsc PAL 4.433619MHz 6 EE = – 10V) : STEREO : BSL2 Through / LINE MUTE OFF : Typ. (+ 9.8dB) : FM OUTPUT ON : FM REC output, MIX ratio 1 (-12.5dB) : NTSC : Recording MUTE : OFF : Hi-Fi MIX : OFF : Typ. : Typ. : FNORM detect, no ENVE output : OFF : L (MUTE) Video ICs BH7800K Parameter Symbol Min. Typ. Max. Unit Conditions [REGULATOR] Quiesent current (positive supply) EE IqP EE 30.0 40.0 53.0 mA EE MODE, after carrier frequency adjustment with no input Quiesent current (positive supply) PB IqP PB 40.0 54.0 72.0 mA PB MODE, carrier frequency adjustment FNORM, after BPF adjustment Quiesent current (negative supply) EE IqM EE – 20.0 – 15.0 – 11.0 mA EE MODE, after carrier frequency adjustment with no input Quiesent current (negative supply) PB IqM PB – 22.0 – 16.0 – 12.0 mA PB MODE, carrier frequency adjustment FNORM, after BPF adjustment Regulator input voltage (positive) VCC 4.75 5.10 5.45 Regulator input voltage (negative) VEE – 5.35 – 5.00 – 4.65 V V [EE THROUGH] (INPUT: TU IN L / R, LINE1 IN L / R, LINE2 IN L / R, BS IN L / R OUTPUT: LINE OUT L / R) Line output level VOEE – 11.4 Channel balance (L / R) CBEE – 0.8 – 10.2 dBV INPUT condition 1 0.0 – 9.0 0.8 dB INPUT condition 1 INPUT condition 1,∗1 Distortion THDEE — 0.017 0.10 % Maximum output level VOMEE 9.0 10.7 — dBV THD = 1%,∗1 – 3.8 – 1.8 + 0.2 dBV INPUT condition 2 ALC ON THDALC — 0.03 0.25 Output residual noise VONEE — – 94.0 – 86.0 dBV Relevant input shorted to GND,∗2 Crosstalk CTEE — – 88.0 – 75.0 dBV Relevant input: shorted to GND,∗2 Non-relevant input: Input condition 2,∗2 Muting level MTEE — – 103 – 90 dBV INPUT condition 2,∗2 ALC level VALC ALC distortion % (INPUT: TU L / R / M IN, BS L / R IN, LINE1 L / R IN, LINE2 L / R IN Normal out output level VONORM [BS / L2 THROUGH] (INPUT: BS / LINE2 L / R IN VOBS VOL2 Output level – 21.5 THDBS THDL2 — Output residual noise VONBS VONL2 — Line amplifier gain1 – 18.5 – 10.2 – 9.0 0.005 0.08 – 99.0 VOMIX dBV VIN = – 20.0dBV % dBV + 9.0 + 9.8 + 10.6 dB – 7.2 – 6.0 – 4.8 Distortion THDMIX — 0.08 0.50 MIX ALC level VALCMIX – 4.2 – 2.7 – 1.2 ∗2: DIN INPUT condition 1 L & R input together,∗1 – 86.0 [MIX AMP] (INPUT: TU IN L / R, LINE1 IN L / R, LINE2 IN L / R, BS IN L / R ∗1: B.W. = 0.4 to 30kHz dBV VIN = – 20.0dBV,∗1 BS IN pin shorted to GND,∗2 OUTPUT: LINE OUT L / R) VOLINE1 Output level OUTPUT: NORMAL OUT) OUTPUT: LINE OUT L / R) – 11.4 Distortion [LINE AMP] (INPUT: NORMAL IN – 20.0 INPUT condition 2,∗1 ALC ON VIN = – 20dBV OUTPUT: MIX OUT) dBV % dBV INPUT condition 1 L & R input together INPUT condition 1 L & R input together,∗1 INPUT condition 2 L & R input together AUDIO 7 Video ICs BH7800K Parameter Symbol Min. Typ. Max. Unit Conditions [MODEM REC MODE] (INPUT: TUNER IN L / R, LINE1 IN L / R, LINE2 IN L / R, BS IN L / R NTSC carrier frequency PAL carrier frequency Frequency deviation Maximum frequency deviation FM output level Carrier 2nd harmonic Carrier 3rd harmonic OUTPUT: FM REC OUT) Lch fNOL 1.2925 1.2975 1.3025 MHz Rch fNOR 1.6940 1.6990 1.7040 MHz Lch fPOL 1.3930 1.3980 1.4030 MHz Rch fPOR 1.7945 1.7995 1.8045 MHz Lch DEVL 44.0 50.0 56.0 ± kHz Rch DEVR 44.0 50.0 56.0 ± kHz Lch DEVMax.L 118 140 162 ± kHz Rch DEVMax.R 118 140 162 ± kHz Lch VOFML 310 355 410 mVP-P FM OUT SW: FM L mode Rch VOFMR 320 365 420 mVP-P Lch f2L — – 53.0 – 40.0 dB Rch f2R — – 48.0 – 40.0 dB Lch f3L — – 52.0 – 40.0 dB Rch f3R — – 55.0 – 42.0 dB FM OUT SW: FM R mode Spectrum ratio of 2nd harmonic with respect to fundamental Lch: FM L mode, Rch: FM R mode Spectrum ratio of 3rd harmonic with respect to fundamental Lch: FM L mode, Rch: FM R mode – 12.5 – 10.7 dB Spectrum ratio 1.30MHz / 1.70MHz FM MIX ratio (FM MIX1 mode) fLR – 14.3 No input, after automatic adjustment No input, after automatic adjustment INPUT condition 1 INPUT condition 3 (f = 10kHz) [MODEM PB MODE] (INPUT: FM PB IN, OUTPUT: LINE OUT L / R) (After BPF f0 adjustment, VIN = 1320mVP-P, 1.30MHz, 1.70MHz MIX IN) Demodulation output level 1 Lch VODL – 12.4 – 10.2 – 8.0 dBV DEVL = ± 50.0kHz, f = 1kHz Rch VODR – 12.4 – 10.2 – 8.0 dBV DEVR = ± 50.0kHz, f = 1kHz Lch VODL2 VODL – 10.0 VODL – 7.8 VODL – 5.6 dBV DEVL = ± 50.0kHz, f = 10kHz VODR2 VODR – 10.0 VODR – 7.8 VODR – 5.6 dBV DEVR = ± 50.0kHz, f = 10kHz Demodulation output level 2 Rch Demodulation distortion Demodulation noise level Lch THDDL — 0.12 0.35 % DEVL = ± 50.0kHz, f = 1kHz,∗1 Rch THDDR — 0.13 0.35 % DEVR = ± 50.0kHz, f = 1kHz,∗1 Lch VONDL — – 98.0 – 85.0 dBV Rch VONDR — – 98.0 – 85.0 dBV Unmodulated ∗2 [Recording→playback overall characteristics] (EE···INPUT: LINE IN L / R, OUTPUT: LINE OUT L / R) (PB···INPUT: FM PB IN, OUTPUT: LINE OUT L / R) Lch VRPL – 1.2 0.0 + 1.2 dB Line output recording / playback level difference Rch VRPR – 1.2 0.0 + 1.2 dB Carrier frequency, after adjusting BPF EE mode: INPUT condition 1 PB mode: FM PB IN = 1320mVP-P f = 1.30MHz, 1.70MHz 1: 1 MIX, The difference between the EE and PB line out levels when input is DEV = DEVL,R (the frequency deviation given above) [FM BPF] (INPUT: FM PB IN, OUTPUT: BPF MONITOR L / R) BPF L / R level difference NTSC ∆VBPFN – 5.0 0.0 5.0 dB After automatic adjustment, NTSC f = 1.505MHz, VIN = 400mVP-P BPF L / R level difference PAL ∆VBPFP – 5.0 0.0 5.0 dB After automatic adjustment, PAL f = 1.605MHz, VIN = 400mVP-P ∗1: B.W. = 0.4 to 30kHz 8 ∗2: DIN AUDIO Video ICs Parameter BH7800K Symbol Min. Typ. Max. Unit Conditions (LcH, RcH mix input signal level 1320mVP-P (RATIO 1: 1)) 〈NTSC Lch〉 1.30MHz insertion loss 1.15MHz attenuation 1.45MHz attenuation 1.70MHz attenuation – 14.1 dB 1.30MHz + 1.70MHz FM ALC ON A T T NLC – 5.3 A T T NLC – 2.3 dB 1.15MHz + 1.70MHz A T T NLC – 5.0 A T T NLC – 2.5 dB 1.45MHz + 1.70MHz — A T T NLC – 30.0 dB 1.30MHz + 1.70MHz A T T NLC – 20.1 – 17.1 A T T NL A T T NLC – 9.8 A T T NLC – 8.1 1.15 A T T NL 1.45 A T T NL 1.70 — 〈NTSC Rch〉 1.70MHz insertion loss 1.55MHz attenuation 1.85MHz attenuation 1.30MHz attenuation A T T NRC – 21.3 – 18.3 – 15.3 dB 1.30MHz + 1.70MHz FM ALC ON A T T NR A T T NRC – 8.8 A T T NRC – 5.7 A T T NRC – 3.4 dB 1.55MHz + 1.30MHz A T T NRC – 9.5 A T T NRC – 4.7 A T T NRC – 1.4 dB 1.85MHz + 1.30MHz — — A T T NRC – 30.0 dB 1.30MHz + 1.70MHz – 12.9 dB 1.40MHz + 1.80MHz A T T PLC – 30.0 dB 1.40MHz + 1.80MHz – 14.3 dB 1.40MHz + 1.80MHz A T T PRC – 30.0 dB 1.40MHz + 1.80MHz 1.55 A T T NR 1.85 A T T NR 1.30 〈PAL Lch〉 1.40MHz insertion loss 1.80MHz attenuation A T T PLC A T T PL 1.80 – 18.9 — – 15.9 — PAL Rch 1.80MHz insertion loss 1.40MHz attenuation A T T PRC A T T PR 1.40 – 20.3 — – 17.3 — [FNORM→Hi-Fi recovery delay circuit] Return delay time τFNDLY 110 125 140 mS Delay time from input of FM PB IN (1.30MHz, 1.70MHz 1: 1 MIX) 1320mVP-P to rise of ENVE OUT AUDIO HEAD PULSE IN : f = 30Hz, 5VP-P, rectangular wave (INPUT: FM PB IN, OUTPUT: ENVE OUT) 〈Envelope output circuit〉 0dB = 1320mVP-P, 1.30MHz & 1.70MHz MIX input Envelope output level SP0 VENVSP0 — 0 100 mV No signal, STANDARD MODE Envelope output level SP1 VENVSP1 2.08 2.58 3.08 V VIN = 0dB, STANDARD MODE Envelope output level SP2 VENVSP2 3.70 3.95 4.20 V VIN = + 10dB, STANDARD MODE Envelope output level EP1 VENVEP1 1.96 2.46 2.96 V VIN = – 4dB, + 4dB MODE L mode holding voltage VH5L 0.0 — 0.5 V H mode holding voltage VH5H 2.5 — VCC V [Control system mode holding voltage] 〈CLOCK IN〉 9 Video ICs BH7800K Parameter Symbol Min. Typ. Max. Unit L mode holding voltage VH6L 0.0 H mode holding voltage VH6H 2.5 — 0.5 V — VCC V MUTE holding voltage VH32L 0.0 DC MUTE holding voltage VH32H 3.9 — 1.0 V — VCC V Conditions 〈DATA IN〉 〈MUTE CTRL〉 NORMAL IN MIX OUT LINE L OUT LINE R OUT 1k 22k 22k 22k MUTE CTRL NORMAL OUT •Measurement circuit VEE 1k 0.022µ 0.0047µ 10µ 2.2M 47µ 1500p 1500p VEE LINE2 R IN S33 33 32 31 30 29 28 27 26 25 24 23 P.OFF: H LINE2 L IN 1k S34 Tr.35 220µ MIX AMP 34 22 PNR R35 0.01µ 35 21 4.7µ 100µ 4.7k 0.022µ D.O COM. LINE AMP 38 20 18 47µ REG 27k 39 VEE 100µ 1k 17 VCO BPF AUTO ADJUST OUTPUT SWITCH 40 LINE1 R IN 27k FMBPF 41 15 S41 4.7k 42 ALC ENVE LOPE MODEM 43 BS R IN 13 DATA DECODER 44 12 S44 1 2 3 4 5 6 7 8 9 1k S2 1k S3 TUNER L IN Fig.1 FSC IN DATA CLOCK VEE TUNER M IN 10 10µ S1 2.2M 1k 47µ TUNER R IN 11 ENVELOPE / Hi-Fi DET / ADJ FLAG FM PB IN 220µ PNR 0.022µ 1k 47k SWITCH S43 BS L IN 14 Hi-Fi DET INPUT 0.0047µ 1k UNREG VEE 10 16 S40 LINE1 L IN 1k AHSWP IN 19 AMP LINE 37 UNREG VCC FM REC OUT 10k MODEM 36 VCC FM OUT SW Video ICs BH7800K Circuit operation •Function table The BH7800K includes the following functions on one chip. No. Block name Main function Pin numbers Power supply 35 ~ 39, 42 UNREG—VCC: + 10V UNREG—VEE: – 10V GND: 38 1 Regulator · ± 5V regulator (VCC, VEE) · Anti-pop circuit (ANTI—POP) 2 SSB control · SSB data decoder 5~7 VCC3 (internal power supply) GND: 7 3 Input switcher · TUNER (L, R, M) / LINE 1, 2 (L,R) / BS (L, R) switch 33, 34, 40, 41 43, 44 1~3 VCC (internally wired) VEE (internally wired) GND: 38 Output switcher · Line amplifier: + 9.8dB, + 10.8dB, + 12.0dB, + 14.8dB · STEREO / LEFT / RIGHT / NORMAL switch · MIX ON / OFF switch · Mute switch · MIXER amplifier for RF converter (with ALC function) · BS / LINE2 through mode 27 ~ 30 32 VCC (internally wired) VEE (internally wired) GND: 38 PNR processor · 20kHz line low-pass filter (secondary LPF) · 20kHz PNR low-pass filter (secondary LPF) · PNR processor (MOA, CCA, WTNG, DET) · Emphasis / de-emphasis (EMPH / DEEMPH) · Switching noise slope-control type differential compensation circuit 9 ~ 12 22 ~ 25 VCC (internally wired) VEE (internally wired) GND: 38 Modulator · FM modulation circuit (VCO, DEV) · FM demodulation / FM BPF MONITOR output switch (FMOUT SW) : FM MIX1 to 4, FM L, FM R, BPF L, BPF R · Recording FM treble cutoff filter (FM LPF) · Over modulation limiter (AUDIO LIM) · Playback FM limiter (FM LIM) · VCO, BPF automatic adjustment circuit (AUTO AUDIO ADJUST) · NTSC / PAL switch function · Auto adjustment complete FLAG output circuit (ADJ FLAG) 8, 14 17, 21 VCC: 18 VEE (internally wired) GND: 15 8 FM detector control · D.O.detector circuit (D.O. DET) · Auto FM detector circuit (noise detect method) (FM DET) : Typ. , + 30%, – 10% · Envelope detector circuit (ENVE) · Hold pulse generator 14, 20 VCC: 18 (internally wired) GND: 15 9 FM BPF · FM bandpass filter (FM BPF) · NTSC / PAL switch function · FM input automatic level adjust circuit (FM ALC: ON / OFF) 4 6 7 13, 16, 19 VCC: 18 GND: 15 11 Video ICs BH7800K NORMAL IN 22k MIX OUT LINE R OUT LINE L OUT NORMAL OUT 22k MUTE CTRL •Application example 1500p 33 32 31 30 29 28 27 0.022µ 10µ 47µ LINE2 R IN 26 25 0.0047µ VEE 2.2M 1500p VEE 24 23 P.OFF: H LINE2 L IN Tr.35 220µ MIX AMP 34 R35 22 PNR 35 21 4.7µ MODEM 36 VCC FM OUT SW 100µ 38 20 AUDIO HEAD SWITCH PULSE IN 0.022µ 19 AMP LINE 37 D.O COM. LINE AMP UNREG VCC 4.7k FM REC OUT 18 47µ REG 27k 39 VEE 100µ SWITCH 27k FMBPF 15 42 ALC ENVE LOPE MODEM INPUT 13 SWITCH DATA DECODER 1 2 3 4 5 6 7 8 9 2.2M 47µ TUNER R IN TUNER L IN 10 11 fsc IN DATA VEE CLOCK TUNER M IN 12 0.0047µ 44 FM PB IN 220µ PNR 10µ BS L IN 43 ENVELOPE / Hi-Fi DET / ADJ FLAG 14 Hi-Fi DET 0.022µ 4.7k BS R IN 16 41 LINE1 L IN UNREG VEE VCO BPF AUTO ADJUST OUTPUT 40 LINE1 R IN 17 Fig.2 notes •TheOperation VCO oscillation frequency and frequency deviation, and the BPF center frequency are directly influenced by the temperature characteristics of the setting resistors connected to pins 16 and 17. Use metal-film components. 12 Video ICs BH7800K •Electrical characteristic curves – 10 – 10 – 20 – 20 1.4MHz 1.7MHz GAIN: Gv (dB) 1.3MHz GAIN: Gv (dB) Rch Lch Rch Lch – 30 – 40 1.8MHz – 30 – 40 – 50 – 50 0.75 1.50 2.25 0.85 1.60 2.35 FREQUENCY: f (MHz) FREQUENCY: f (MHz) Fig. 3 FM BPF frequency characteristics (NTSC) Fig. 4 FM BPF frequency characteristics (PAL) •External dimensions (Units: mm) 14.0 ± 0.3 10.0 ± 0.2 23 22 44 12 2.15 ± 0.1 0.05 1 0.8 11 0.35 ± 0.1 1.2 14.0 ± 0.3 10.0 ± 0.2 33 34 0.15 ± 0.1 0.15 QFP44 13