2-output LDO series regulator BA33C25FP/HFP Description Dimension (Unit : mm) BA33C25FP/HFP is a 2-output LDO series regulator IC. Output current is 1A at maximum and output voltage accuracy is +/-2%. This IC incorporates over-current protection and thermal protection circuits. 1.5±0.2 BA33C25FP 2.3±0.2 6.5±0.2 +0.2 5.1−0.1 0.5±0.1 Features 1) 3.3V/1A, 2.5V/1A 2) Output voltage accuracy: +/-2% 3) PNP output and LDO voltage type 4) Built-in output current limit circuit protects the IC from destruction by short 5) Built-in temperature protection circuit protects the IC from thermal destruction by overload state 6) TO252-5 package, HRP-5 package 3 4 5 1.27 0.5 0.5±0.1 1.0±0.2 TO252-5 BA33C25HFP 1.905±0.1 0.835±0.2 1 2 3 4 5 Applications S 0.08±0.05 DVD-ROM, DVD-RW, HDD Symbol Limits VCC 18 Pd Unit V ∗1 2300 Topr -40 ~ +105 Tstg -55 ~ +150 ∗1 Derating : 18.4mW/˚C for operation above Ta ≥ 25˚C PCB (70mmx70mm, t=1.6mm) glass epoxy mounting. (Thermal via on the board.) (Board surface copper foil area: 10.5mmX10.5mm) (2 layer board (Back copper foil area: 15mmX15mm) Recommended Operating Conditions (Ta=25˚C) Parameter Input supply voltage 3.3V output current 2.5V output voltage mW ˚C ˚C Symbol Min. Typ. Max. Unit VCC Io1 4.1 - - - 16.0 1 1 V A Io2 0.73±0.1 D 0 .0 8 S HRP-5 Absolute Maximum Ratings (Ta=25˚C) Parameter 1.72 A 1.523±0.15 8.0±0.13 (7.49) 8.82±0.1 (5.59) 10.54±0.13 1.017±0.2 9.39±0.125 1.2575 Applied voltage Power dissipation Operating temperature range Storage temperature range 1.5 2 0.8 1 2.5 9.5±0.5 5.5±0.2 2-C0.5 4.5° + 5.5° − 4.5° 0.27 + 0.1 − 0.05 Electrical characteristics (Unless otherwise noted; Ta=25˚C, Vcc=5V) Parameter Symbol Min. Typ. Max. Unit Conditions Ib - 0.8 1.5 mA Vo1 3.234 3.3 3.366 V Io1=500mA ∆Vd1 - 0.25 0.50 V Io1=500mA, Vcc=3.135V Io1 1.0 - - Ripple rejection 1 R.R. 1 50 58 - Input stability 1 Reg.I1 - 5 30 Reg.L1 - 30 75 - ±0.01 - IOS1 - 300 - Vo2 2.450 2.5 - 2.550 - V 58 - dB f=120Hz, ein=1Vrms, Io2=200mA 5 30 mV Vcc=4.1 → 16V, Io2=500mA 30 Io2=0mA → 1A ±0.01 75 - mV 270 - mA Vcc=16V Bias current Io=0mA, Io2=0mA <3.3V output> Output voltage 1 Min. I/O voltage difference 1 Output current capacity 1 Load stability 1 Output voltage temperature coefficient 1 ∗2 Output short current 1 <2.5V output> Output voltage 2 Tcvo1 Io2 Output current capacity 2 1.0 Ripple rejection 2 R.R. 2 Input stability 2 Reg.I2 50 - Reg.L2 - Load stability 2 Output voltage temperature coefficient 2 ∗2 Tcvo2 - Output short current 2 IOS2 ∗This product is not designed for protection against radioactive rays. ∗2 Design guaranteed (All total inspection is not performed.) A dB f=120Hz, ein=1Vrms, Io1=200mA mV Vcc=4.1 → 16V, Io1=500mA mV Io1=0mA → 1A % /˚C Io1=5mA, Tj=0~125˚C mA Vcc=16V Io2=500mA A % / ˚C Io1=5mA, Tj=0~125˚C Block Diagram BA33C25FP/HFP Vcc Vcc Reference Voltage Current Limit Sat. Prevention Vcc Thermal Shut Down Vcc N.C. Current Limit GND(FIN) Vcc Sat. Prevention Vo1 Vo2 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document use silicon as a basic material. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.0