LM5060 www.ti.com SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 LM5060 High-Side Protection Controller with Low Quiescent Current Check for Samples: LM5060 FEATURES APPLICATIONS • • • • 1 2 • • • • • • • • • • Available in Automotive Grade / AEC Q-100 Wide Operating Input Voltage Range: +5.5V to +65V Less than 15 µA Quiescent Current in Disabled Mode Controlled Output Rise Time for Safe Connection of Capacitive Loads Charge Pump Gate Driver for External NChannel MOSFET Adjustable Under-Voltage Lock-Out (UVLO) with Hysteresis UVLO Serves as Second Enable Input for Systems Requiring Safety Redundancy Programmable Fault Detection Delay Time MOSFET Latched off After Load Fault is Detected Active Low Open Drain POWER GOOD (nPGD) Output Adjustable Input Over-Voltage Protection (OVP) Immediate Restart After Over-Voltage Shutdown Automotive Body Electronics Industrial Power Distribution and Control PACKAGE • 10-Lead VSSOP DESCRIPTION The LM5060 high-side protection controller provides intelligent control of a high-side N-Channel MOSFET during normal on/off transitions and fault conditions. In-rush current is controlled by the nearly constant rise time of the output voltage. A power good output indicates when the output voltage reaches the input voltage and the MOSFET is fully on. Input UnderVoltage Lock-Out, with hysteresis, is provided as well as programmable input Over-Voltage Protection. An enable input provides remote On / Off control. The programmable Under-Voltage Lock-Out input can be used as second enable input for safety redundancy. A single capacitor programs the initial start-up VGS fault detection delay time, the transition VDS fault detection delay time, and the continuous OverCurrent VDS fault detection delay time. When a detected fault condition persists longer than the allowed fault delay time, the MOSFET is latched off until either the Enable input or the Under-Voltage Lock-Out input is toggled low and then high. Typical Application VIN VOUT SENSE GATE OUT VIN LM5060 UVLO OVP STATUS EN TIMER High = Fault, Low= OK nPGD High = On, Low= Off GND GND EN GND 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2009–2013, Texas Instruments Incorporated LM5060 SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 www.ti.com Connection Diagram VIN 2 OVP 3 UVLO 4 EN 5 10 GATE LM5060Q1MM SENSE 1 9 OUT 8 nPGD 7 TIMER 6 GND Figure 1. 10-Lead VSSOP See Package Number DGS0010A PIN DESCRIPTIONS Pin No. Name Description Applications Information 1 SENSE Input Voltage Sense A constant current sink (16 μA typical) at the SENSE pin flows through an external resistor to set the threshold for fault detection. 2 VIN Supply Voltage Input The operating voltage range is 5.5V to 65V. The internal power-on-reset (POR) circuit typically switches to the active state when the VIN pin is greater than 5.1V. A small ceramic bypass capacitor close to this pin is recommended to suppress noise. OVP Over-Voltage Protection Comparator Input An external resistor divider from the system input voltage sets the Over-Voltage turn-off threshold. The GATE pin is pulled low when OVP exceeds the typical 2.0V threshold, but the controller is not latched off. Normal operation resumes when the OVP pin falls below typically 1.76V. Under-Voltage LockOut Comparator Input The UVLO pin is used as an input Under-Voltage Lock-Out by connecting this pin to a resistor divider between input supply voltage and ground. The UVLO comparator is activated when EN is high. A voltage greater than typically 1.6V at the UVLO pin will release the pull down devices on the GATE pin and allow the output to gradually rise. A constant current sink (5.5 µA typical) is provided to ensure the UVLO pin is low in an open circuit condition. A voltage less than 0.8V on the EN pin switches the LM5060 to a low current shutdown state. A voltage greater than 2.0V on the EN pin enables the internal bias circuitry and the UVLO comparator. The GATE pin pull-up bias is enabled when both EN and UVLO are in the high state. A constant current sink (6 µA typical) is provided to ensure the EN pin is low in an open circuit condition. 3 4 UVLO 5 EN Enable Input 6 GND Circuit ground 7 TIMER Timing capacitor 8 nPGD Fault Status 9 OUT Output VoltageSense 10 GATE Gate drive output An external capacitor connected to this pin sets the VDS fault detection delay time. If the TIMER pin exceeds the 2.0V threshold condition, the LM5060 will latch off the MOSFET and remain off until either the EN, UVLO or VIN (POR) input is toggled low and then high. An open drain output. When the external MOSFET VDS decreases such that the OUT pin voltage exceeds the SENSE pin voltage, the nPGD indicator is active (low = no fault). Connect to the output rail (external MOSFET source). Internally used to detect VDS and VGS conditions. Connect to the external MOSFET’s gate. A charge-pump driven constant current source (24 µA typical) charges the GATE pin. An internal zener clamps the GATE pin at typically 16.8V above the OUT pin. The ΔV/Δt of the output voltage can be reduced by connecting a capacitor from the GATE pin to ground. These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 2 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 LM5060 www.ti.com SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 Absolute Maximum Ratings (1) (2) VIN to GND (3) (4) -0.3V to 75V SENSE, OUT to GND (5) -0.3V to 75V GATE to GND (3) (5) -0.3V to 75V EN, UVLO to GND (4) -0.3V to 75V nPGD, OVP to GND -0.3V to 75V TIMER to GND -0.3V to 7V ESD Rating, HBM (6) 2 kV −65°C to + 150°C Storage Temperature Peak Reflow Temperature (7) 260°C Junction Temperature 150°C (1) (2) (3) (4) (5) (6) (7) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur, including in-operability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. Operating Range conditions indicate the conditions at which the device is functional and the device should not be operated beyond such conditions. For ensured specifications and conditions, see the Electrical Characteristics table. If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications. The GATE pin voltage is typically 12V above the VIN pin when the LM5060 is enabled. Therefore, the Absolute Maximum Rating for VIN (75V) applies only when the LM5060 is disabled, or for a momentary surge to that voltage since the Absolute Maximum Rating for the GATE pin is also 75V. The minimum voltage of -1V is allowed if the current is limited to below -25 mA. Also it is assumed that the negative voltage on the pins only occur during reverse battery condition when a positive supply voltage (Vin) is not applied. The minimum voltage of -25V is allowed if the current is limited to below -25 mA. Also it is assumed that the negative voltage on the pins only occur during reverse battery condition when a positive supply voltage (VIN) is not applied. The Human Body Model (HBM) is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. Applicable standard is JESD22–A114–C. Soldering process must comply with Texas Instruments' Reflow Temperature Profile specifications. Reflow temperature profiles are different for lead-free and non-lead-free packages. Refer to the Packaging Data Book available from Texas Instruments, or : www.ti.com/packaging Operating Ratings (1) VIN Supply Voltage 5.5V to 65V EN Voltage 0.0V to 65V UVLO Voltage 0.0V to 65V nPGD Off Voltage 0V to 65V nPGD Sink Current 0mA to 5mA −40°C to + 125°C Junction Temperature Range (1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur, including in-operability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. Operating Range conditions indicate the conditions at which the device is functional and the device should not be operated beyond such conditions. For ensured specifications and conditions, see the Electrical Characteristics table. Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 3 LM5060 SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 www.ti.com Electrical Characteristics Unless otherwise stated the following conditions apply: VIN = 14V, EN =2.00V, UVLO =2.00V, OVP = 1.50V, and TJ = 25°C. Limits in standard type are for TJ = 25°C only; limits in boldface type apply over the operating junction temperature (TJ) range of -40°C to +125°C. Minimum and Maximum limits are ensured through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference purposes only. Symbol Parameter Conditions Min Typ Max Units VIN Pin IIN-EN Input Current, Enabled Mode - 1.4 1.7 mA IIN-DIS Input Current, Disabled Mode EN = 0.50V - 9 15 µA IIN-STB Input Current, Standby Mode UVLO = 0.00V - 0.56 0.80 mA POREN Power On Reset Threshold at VIN VIN Rising - 5.1 5.46 V POREN Hysteresis VIN Falling - 500 - mV IOUT-EN OUT Pin Bias Current, Enabled OUT = VIN, Normal Operation 5.0 8 11.0 µA IOUT-DIS OUT Pin Leakage Current, Disabled (1) Disabled, OUT = 0V, SENSE = VIN - 0 - μA POREN-HYS OUT Pin SENSE Pin ISENSE Threshold Programming Current SENSE Pin Bias Current 13.6 16 18.0 µA VOFFSET VDS Comparator Offset Voltage SENSE - OUT Voltage for Fault Detection -7.0 0 7.0 mV IRATIO ISENSE and IOUT-EN Current Ratio ISENSE / IOUT-EN 1.70 2.0 2.30 OVP Pin Threshold Voltage Rising 1.88 2.0 2.12 V - 240 - mV OVP Input OVPTH OVP Threshold OVPHYS OVP Hysteresis OVPDEL OVP Delay Time Delay from OVP Pin > OVPTH to GATE low - 9.6 - µs OVPBIAS OVP Pin Bias Current OVP = 1.9V - 0 0.50 µA UVLOTH UVLO Threshold UVLO Pin Threshold Voltage Rising 1.45 1.6 1.75 V UVLOHYS UVLO Hysteresis 120 180 230 mV UVLOBIAS UVLO Pin Pull-Down Current 3.8 5.5 7.2 µA ENTHH High-level input voltage 2.00 - - V ENTHL Low-level input voltage - - 0.80 V ENHYS EN Threshold Hysteresis - 200 - mV ENBIAS EN Pin Pull-down current - 6 8.0 µA 17 24 31 µA UVLO Input EN Input Gate Control (GATE Pin) IGATE Gate Charge (Sourcing) Current On-state On-state IGATE-OFF Gate Discharge (Sinking) Current Off state UVLO = 0.00V - 2.2 - mA IGATE-FLT Gate Discharge (Sinking) Current Fault state OUT < SENSE - 80 - mA Gate output voltage in normal operation GATE - VIN Voltage GATE Pin Open 10 12 14 V VGS Status Comparator Threshold voltage GATE - OUT threshold voltage for TIMER voltage reset and TIMER current change 3.50 5 6.50 V Zener Clamp between GATE Pin and OUT Pin IGATE-CLAMP = 0.1mA - 16.8 - V VGATE VGATE-TH VGATE-CLAMP (1) 4 The GATE pin voltage is typically 12V above the VIN pin when the LM5060 is enabled. Therefore, the Absolute Maximum Rating for VIN (75V) applies only when the LM5060 is disabled, or for a momentary surge to that voltage since the Absolute Maximum Rating for the GATE pin is also 75V. Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 LM5060 www.ti.com SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 Electrical Characteristics (continued) Unless otherwise stated the following conditions apply: VIN = 14V, EN =2.00V, UVLO =2.00V, OVP = 1.50V, and TJ = 25°C. Limits in standard type are for TJ = 25°C only; limits in boldface type apply over the operating junction temperature (TJ) range of -40°C to +125°C. Minimum and Maximum limits are ensured through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference purposes only. Symbol Parameter Conditions VTMRH Timer Fault Threshold TIMER Pin Voltage Rising VTMRL Timer Re-enable Threshold TIMER pin Voltage Falling ITIMERH Timer Charge Current for VDS Fault ITIMERL ITIMERR Min Typ Max Units - 2.0 - V - 0.30 - V TIMER Charge current after Start-Up. VGS = 6.5V 8.5 11 13.0 µA Timer Start-Up Charge Current TIMER Charge current during Start-Up. VGS = 3.5V 4.0 6 7.0 µA Timer Reset Discharge Current TIMER Pin = 1.5V 4.4 6 8.2 mA Fault to GATE Low delay TIMER Pin > 2.0V No load on GATE pin - 5 - µs Timer (TIMER Pin) tFAULT Power Good (nPGD Pin) PGDVOL Output low voltage ISINK = 2 mA - 80 205 mV PGDIOH Off leakage current VnPGD = 10V - 0.02 1.00 µA Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 5 LM5060 SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 www.ti.com Typical Performance Characteristics 6 VIN Pin Current vs. VIN Pin Voltage VGATE, VIN Voltage vs. Input Voltage Figure 2. Figure 3. OUT Pin Current (IOUT-EN) vs. VIN Voltage GATE Current (IGATE) vs VIN Voltage Figure 4. Figure 5. SENSE Current (ISENSE) vs VIN Voltage nPGD Low Voltage (PGDVOL vs Sink Current) Figure 6. Figure 7. Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 LM5060 www.ti.com SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 Typical Performance Characteristics (continued) GATE Pull-Down Current Off (IGATE-OFF) vs. GATE Voltage EN Threshold Voltage (ENTH) vs. Temperature Figure 8. Figure 9. UVLO Threshold Voltage (UVLOTH) vs. Temperature GATE Pull-Down Current Fault (IGATE-FLT) vs. GATE Voltage Figure 10. Figure 11. UVLO, EN Current vs. Temperature OVP Threshold (OVPTH), Hysteresis (OVPHYS) vs. Temperature Figure 12. Figure 13. Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 7 LM5060 SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 www.ti.com Typical Performance Characteristics (continued) VGS Comparator Threshold Voltage (VGATE-TH) vs. Temperature VDS Comparator Offset Voltage (VOFFSET) vs. Temperature Figure 14. Figure 15. GATE Current (IGATE) vs. Temperature GATE Output Voltage (VGATE) vs. Temperature Figure 16. Figure 17. Gate Pull-Down Current - Fault (IGATE-FLT) vs. Temperature Figure 18. 8 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 LM5060 www.ti.com SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 Typical Performance Characteristics (continued) VIN Pin Current (IEN) vs EN Voltage nPGD Low Voltage (PGDVOL) vs. Temperature Figure 19. Figure 20. Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 9 LM5060 SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 www.ti.com Block Diagram GATE OUT LM5060 VIN IGATE 24 PA Charge Pump 16.8V 1 k: VGS Status Comparator IOUT-EN 8 PA VGATE-TH 5V Normal OFF OUT+5V VDS Fault Comparator IGATE-OFF 2.2 mA 500: SENSE Fault OFF ISENSE 16 PA IGATE-FLT 80 mA nPGD PGOOD 6 PA: Start-Up Fault Timer 11 PA: O-C (VDS) Fault Timer One shot 5 PA OVP 6 PA OV OVPTH 2.0V UVLOTH 1.6V TIMER UVLO ITIMERR 6 mA UVLOBIAS 5.5 PA nEN S Q Reset Latch 1.5V R EN ENBIAS 6 PA VTMRL 0.3V Enable Bias Circuit Fault GND Q S Fault Latch VTMRH 2.0V R VIN POR nEN + POR POREN 5.1V 10 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 LM5060 www.ti.com SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 Q1 VIN VOUT RS SENSE GATE OUT VIN R4 R10 LM5060 UVLO R8 R11 R9 STATUS EN High = Fault, Low= OK OVP TIMER C1 nPGD GND High = On, Low= Off EN GND GND Figure 21. Basic Application Circuit Functional Description The LM5060 is designed to drive an external high-side N-channel MOSFET. Over-Current protection is implemented by sensing the voltage drop across the MOSFET. When an adjustable voltage drop threshold is exceeded, and an adjustable time period has elapsed, the MOSFET is disabled. Over-Voltage Protection (OVP) and Under-Voltage Lock-Out (UVLO) monitoring of the input line is also provided. A low state on the enable pin will turn off the N-channel MOSFET and switch the LM5060 into a very low quiescent current off state. An active low power good output pin is provided to report the status of the N-channel MOSFET. The waiting time before the MOSFET is turned off after a fault condition is detected can be adjusted with an external timer capacitor. Since the LM5060 uses a constant current source to charge the gate of the external N-channel MOSFET, the output voltage rise time can be adjusted by adding external gate capacitance. This is useful when starting up into large capacitive loads. POWER-UP SEQUENCE The basic application circuit is shown in Figure 21 and a normal start-up sequence is shown in Figure 22. Startup of the LM5060 is initiated when the EN pin is above the (ENTHH) threshold (2.0V). At start-up, the timer capacitor is charged with a 6 µA (typical) current source while the gate of the external N-channel MOSFET is charged through the GATE pin by a 24 µA (typical) current source. When the gate-to-source voltage (VGS) reaches the VGATE-TH threshold (typically 5V) the VGS sequence ends, the timer capacitor is quickly discharged to 0.3V, and begins charging the timer capacitor with a11 µA current source. The timer capacitor will charge until either the VDS Comparator indicates that the drain-to-source voltage (VDS) has been reduced to a nominal value (i.e. no fault) or the voltage on the timer capacitor has reached the VTMRH threshold (i.e. fault). The VDS Comparator monitors the voltage difference between the SENSE pin and the OUT pin. The SENSE pin voltage is user programmed to be lower than the input supply voltage by selecting a suitable sense resistor value. When the OUT pin voltage exceeds the voltage at the SENSE pin, the nPGD pin is asserted low (i.e. no fault) and the timer capacitor is discharged. STATUS CONDITIONS Output responses of the LM5060 to various input conditions is shown in Table 1. The input parameters include Enable (EN), Under-Voltage Lock-Out (UVLO), Over-Voltage Protection (OVP), input voltage (VIN), Start-Up Fault (VGS) and Run Fault (VDS) conditions. The output responses are the VIN pin current consumption, the GATE charge current, the TIMER capacitor charge (or discharge) current, the GATE discharge current if the timer capacitor voltage has reached the VTMRH threshold (typically 2V), as well as the status of nPGD. Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 11 LM5060 SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 www.ti.com VTMRH 11 PA VTIMER 6 PA VTMRL VGATE-TH VGS transition region nPGD Fault VGS Status EN VGS < 5V OFF OK VGS > 5V ON Figure 22. Voltages During Normal Start Up Sequence Table 1. Overview of Operating Conditions Input Conditions Outputs Status UVLO OVP (typ) VIN (typ) SENSE-OUT GATEOUT VIN Current (typ) L L - >5.10V NA NA 0.009 mA 2.2 mA sink Low NA NA Disabled L H - >5.10V NA NA 0.009 mA 2.2 mA sink Low NA NA Disabled EN H L <2V >5.10V H L >2V >5.10V H H <2V >5.10V H H <2V >5.10V SENSE>OUT SENSE<OUT SENSE>OUT SENSE<OUT SENSE>OUT SENSE<OUT SENSE>OUT GATE Current (typ) TIMER GATE after TIMER > 2V nPG D NA 0.56 mA 2.2 mA sink Low NA NA 0.56 mA 80 mA sink Low NA <5V 1.4 mA 24 µA source 6 µA source 80 mA sink H Low NA L >5V 1.4 mA 24 µA source 11 µA source 80 mA sink H Low NA L SENSE<OUT H H >2V >5.10V H H <2V <5.10V (1) SENSE>OUT SENSE<OUT NA H NA 1.4 mA 80 mA sink Low NA NA 1.4 mA 2.2 mA sink (See (1)) Low NA L H L H L H Standby Standby Enabled Enabled Over Voltage Power on reset The 2.2 mA sink current is valid for with the VIN pin ≥ 5.1V. When the VIN pin < 5.1V the sink current is lower. See ‘GATE Pin Off Current vs. VIN’ plot in Typical Performance Characteristics. GATE CONTROL A charge pump provides bias voltage above the input and output voltage to enhance the N-Channel MOSFET’s gate. When the system voltage is initially applied and both EN and UVLO are above their respective thresholds, the GATE pin is charged by the 24 µA (typical) current source. During normal operating conditions, the GATE pin voltage is clamped to approximately 16.8V above the OUT pin (i.e. VGS) by an internal zener. When either the UVLO input or the EN input is low, or when VIN is below the Power-On Reset voltage of 5.10V (typical), the GATE pin is discharged with a 2.2 mA (typical) current sink. When the timer capacitor is charged up to the VTMRH threshold (typically 2V) a fault condition is indicated and the gate of the external N-Channel MOSFET is discharged at a 80 mA (typical) rate . Additionally, when the OVP pin voltage is higher than the OVPTH threshold (typically 2V) a fault is indicated and the gate of the external NChannel MOSFET is discharged at the same 80 mA (typical) rate. 12 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 LM5060 www.ti.com SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 FAULT TIMER An external capacitor connected from the TIMER pin to the GND pin sets the fault detection delay time. If the voltage on the TIMER capacitor reaches the VTMRH threshold (2V typical) a fault condition is indicated. The LM5060 will latch off the MOSFET by discharging the GATE pin at a 80mA (typical) rate, and will remain latched off until either the EN pin, the UVLO pin, or the VIN pin is toggled low and then high. The block diagram of the LM5060 shows the details of the TIMER pin. There are three relevant components to the TIMER pin’s function: 1. A constant 6 µA (typical) current source driving the TIMER pin. This current source is active when EN, UVLO, and VIN are all high. 2. A second current source (5 µA typical) is activated, for a total charge current of 11 µA (typical), only when the VGS sequence has completed successfully. 3. A pull-down current sink for the TIMER pin which resets the timer by discharging the timer capacitor. If EN, UVLO or VIN is low, or when OVP is high, the timer capacitor is discharged. (a) When the VDS Fault Comparator detects a fault, (SENSE pin voltage higher than OUT pin voltage) the timer capacitor pull down is disabled and the timer capacitor is allowed to charge at the 11 µA (typical) rate. During Start-Up, the timer behaves as follows: After applying sufficient system voltage and enabling the LM5060 by pulling the EN and UVLO pins high, the timer capacitor will be charged with a 6 µA (typical) current source. The timer capacitor is discharged when the voltage difference between the GATE pin and the OUT pin (i.e. VGS of the external N-Channel MOSFET) reaches the VGATE-TH threshold (typically 5V). After discharging, the timer capacitor is charged with 11 µA until either the VTMRH threshold (typically 2V) is reached, or the sensed VDS voltage falls below the threshold of the VDS Fault Comparator, indicating the output voltage has reached the desired steady state level. The timer capacitor voltage waveforms are illustrated in Figure 22, Figure 23 and Figure 24. A timer capacitor is always necessary to allow some finite amount of time for the gate to charge and the output voltage to rise during startup. If an adequate timer capacitor value is not used, then the 6 µA of charge current would cause the TIMER pin voltage to reach the VTMRH fault threshold (typically 2V) prematurely and the LM5060 will latch off since a fault condition would have been indicated. Although not recommended, the timer function can be disabled by connecting the TIMER pin directly to GND. With this condition the TIMER pin voltage will never reach the VTMRH fault threshold (2V typical). The end result is that the fault latch-off protection is completely disabled, while the nPGD pin will continue to reflect the VDS Fault Comparator output. VGS CONSIDERATIONS The VGS Status Comparator shown in the LM5060 block diagram accomplishes two purposes: 1. As the gate of the external MOSFET is charged, the VGS voltage transitions from cut-off, through an active region, and into the ohmic region. The LM5060 provides two fault timer modes to monitor these transitions. The TIMER pin capacitor is initially charged with a constant 6 µA (typical) until either the MOSFET VGS reaches the VGATE–TH threshold (typically 5V) indicating that the MOSFET channel is at least somewhat enhanced, or the voltage on the TIMER pin reaches the VTMRH threshold (typically 2V) indicating a fault condition. If the MOSFET VGS reaches 5V threshold before the TIMER pin reaches the typical 2V timer fault threshold, the timer capacitor is then discharged to 300 mV, and then begins charging with 11 µA current source while the MOSFET transitions through the active region. The lower timer capacitor charge current during the initial start-up sequence allows more time before a fault is indicated. The turn-on time of the MOSFET will vary with input voltage, load capacitance, load resistance, as well as the MOSFET characteristics. 2. Figure 23 shows a start-up waveform with excessive gate leakage. The initial charge current on the timer capacitor is 6 µA (typical), while the simultaneous charge current to the gate is 24 µA (typical). Due to excessive gate leakage, the 24 µA is not able to charge the gate to the required typical 5V VGS threshold and the VDS Fault Comparator will indicate a fault when the timer capacitor is charged to the VTMRH fault threshold. When the timer capacitor voltage reaches theVTMRH fault threshold (typically 2V) the MOSFET gate is discharged at an 80 mA (typical) rate. Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 13 LM5060 SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 www.ti.com VTRMRH VTIMER 6 PA Fault Latch VTRMRL GATE pin will be discharged to GND at 80 mA rate VGATE-TH VGS nPGD Fault VGS < 5V VGS Status EN OFF ON Figure 23. Voltages During Startup with VGS Gate Leakage Condition VDS FAULT CONDITION The LM5060 includes a VDS Fault Comparator that senses the voltage difference between the SENSE pin and the OUT pin. If the voltage at the OUT pin falls lower than the voltage at the SENSE pin, the VDS Fault Comparator will trip and switch the nPGD pin to a high impedance state. It will also initiate charging of the capacitor on the TIMER pin with a 6 µA (typical) current source if VGS is less than than 5V, or a 11 µA (typical) current source if VGS is higher than 5V. If the voltage on the TIMER pin reaches the typical 2V fault threshold, the gate of the N-Channel MOSFET is pulled low with a 80 mA (typical) sink current. Figure 24 illustrates a VDS fault condition during start-up. The nPGD pin never switches low because the VDS fault comparator detects excessive VDS voltage throughout the entire sequence. OVER-CURRENT FAULT The VDS Fault Comparator can be used to implement an Over-Current shutdown function. The VDS Fault Comparator monitors the voltage difference between the SENSE pin and the OUT pin. This is, essentially, the same voltage that is across the N-Channel MOSFET RDS(ON) less the threshold voltage that is set by the series resistor on the SENSE pin. The value of capacitor on the TIMER pin, the capacitor charge current (ITIMERH, 11 uA typical), along with the TIMER pin fault threshold (VTMRH) will determine the how long the N-Channel MOSFET will be allowed to conduct excessive current before the MOSFET is turned-off. When this delay time expires, the gate is discharged at a 80 mA rate. The LM5060 is intended for applications where precise current sensing is not required, but some level of fault protection is needed. Examples are applications where inductance or impedance in the power path limits the current rise in a short circuit condition. The Safe Operating Area (SOA) of the external N-Channel MOSFET should be carefully considered to ensure the peak drain-to-source current and the duration of the fault delay time is within the SOA rating of the MOSFET. Also note that the RDS(ON) variations of the external N-Channel MOSFET will affect the accuracy of the OverCurrent detection. RESTART AFTER OVER-CURRENT FAULT EVENT When a VDS fault condition has occurred and the TIMER pin voltage has reached 2V, the LM5060 latches off the external MOSFET. In order to initiate a restart, either the EN pin, the VINpin, or the UVLO pin must be toggled low and then high. 14 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 LM5060 www.ti.com SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 VTMRH 11 PA 6 PA VTIMER Fault Latch VTMRL GATE pin will be discharged to GND at 80 mA rate VGS = 5V VGS VGATE-TH transition region nPGD Fault VGS < 5V VGS Status EN OFF VGS > 5V ON Figure 24. Voltages During Startup with VDS Fault Condition ENABLE The LM5060 Enable pin (EN) allows for remote On/Off control. The Enable pin on/off thresholds are CMOS compatible. The external N-Channel MOSFET can be remotely switched Off by forcing the EN pin below the lower input threshold, ENTHL (800 mV). The external N-Channel MOSFET can be remotely switched On by forcing the EN pin above the upper input threshold, ENTHH (2.00V). Figure 25 shows the threshold levels of the Enable pin. When the EN pin is less than 0.5V (typical) the LM5060 enters a low current (disabled) state. The current consumption of the VIN pin in this condition is 9 µA (typical). up to 65V ON 2.0V (ENTHH) 1.5V (typical) 200 mV (hysterisis) 0.8V (ENTHL) 0.5V (disabled) OFF disabled Figure 25. Enable Function Threshold Levels UNDER-VOLTAGE LOCK-OUT (UVLO) The Under-Voltage Lock-Out function will turn off the external N-Channel MOSFET with a 2.2 mA (typical) current sink at the GATE pin. Figure 26 shows the threshold levels of the UVLO input. A resistor divider as shown in Figure 21 with R10 and R11 sets the voltage at which the UVLO function engages. The UVLO pin may also be used as a second enable pin for applications requiring a redundant, or secondary, shut-down control. Unlike the EN pin function, the UVLO function does not switch the LM5060 to the low current (disabled) state. If the Under-Voltage Lock-Out function is not needed, the UVLO pin should be connected to the VIN pin. The UVLO pin should not be left floating as the internal pull-down will keep the UVLO active. Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 15 LM5060 SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 www.ti.com In addition to the programmable UVLO function, an internal Power-On-Reset (POR) monitors the voltage at the VIN pin and turns the MOSFET Off when VIN falls below typically 5.10V. up to 65V OK 1.6V (UVLOTH) 180 mV (hysterisis) UVLO Figure 26. Under-Voltage Lock-Out Threshold Levels OVER-VOLTAGE PROTECTION (OVP) The Over-Voltage Protection function will turn off the external N-Channel MOSFET if the OVP pin voltage is higher than the OVPTH threshold (typically 2V). A resistor divider made up with R8 and R9, shown in Figure 21, sets the Over-Voltage Protection threshold. An internal 9.6 µs timer filters the output of the Over-Voltage Comparator to prevent noise from triggering an OVP event. An OVP event lasting longer than typically 9.6 µs will cause the GATE pin to be discharged with an 80 mA current sink and will cause the capacitor on the TIMER pin to be discharged. If the Over-Voltage Protection function is not needed, the OVP pin should be connected to GND. The OVP pin should not be left floating. RESTART AFTER OVP EVENT After the OVP function has been activated and the gate of the external N-Channel MOSFET has been pulled low, the OUT pin is likely to be low as well. However, an OVP condition will not cause the VDS Fault Comparator to latch off of the LM5060 because the capacitor on the TIMER pin is also discharged during an OVP event. After the OVP pin falls below the lower threshold (typically 1.76V), the LM5060 will re-start as described in the normal start-up sequence and shown in Figure 22. The EN, VIN, or UVLO pins do not need to be toggled low to high to re-enable the MOSFET after an OVP event. nPGD Pin The nPGD pin is an open drain connection that indicates when a VDS fault condition has occurred. If the SENSE pin voltage is higher than the OUT pin voltage the state of the nPGD pin will be high impedance. In the typical application, as shown in Figure 21, the voltage at the nPGD pin will be high during any VDS fault condition. The nPGD state is independent of the fault timer function. The resistance R4 should be selected large enough to safely limit the current into the nPGD pin. Limiting the nPGD low state current below 5 mA is recommended. 16 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 LM5060 www.ti.com SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 APPLICATION INFORMATION VDS FAULT DETECTION and SELECTING SENSE PIN RESISTOR RS The LM5060 monitors the VDS voltage of the external N-Channel MOSFET. The drain to source voltage threshold (VDSTH), which is set with the resistor RS, is shown in Figure 27; VDSTH = (RS x ISENSE) - VOFFSET (1) The MOSFET drain to source current threshold is: IDSTH = VDSTH RDS(ON) where • • • RDS(ON) is the resistive drop of the pass element Q1 in Figure 27 VOFFSET is the offset voltage of the VDS comparator ISENSE (16 µA typical) is the threshold programming current VIN (2) VOUT Q1 RS SENSE GATE OUT VIN LM5060 Figure 27. Setting the VDS Threshold TURN-ON TIME To slow down the output rise time a capacitor from the GATE pin to GND may be added. The turn on time depends on the threshold level of the N-Channel MOSFET, the gate capacitance of the MOSFET as well as the optional capacitance from the GATE pin to GND. Figure 28 shows the slow down capacitor C1. Reducing the turn-on time allows the MOSFET (Q1), to slowly charge a large load capacitance. Special care must be taken to keep the MOSFET within its safe operating area. If the MOSFET turns on too slow, the peak power losses may damage the device. VIN VOUT Q1 C1 RS SENSE GATE OUT VIN LM5060 Figure 28. Turn-On Time Extension Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 17 LM5060 SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 www.ti.com FAULT DETECTION DELAY TIME To allow the gate of the MOSFET adequate time to change, and to allow the MOSFET to conduct currents beyond the protection threshold for a brief period of time, a fault delay timer function is provided. This feature is important when drive loads which require a surge of current in excess of the normal ON current upon start up, or at any point in time, such as lamps and motors. A single low leakage capacitor (CTIMER) connected from the TIMER (pin 7), to ground sets the delay time interval for both the VGS status detection at start-up and for the subsequent VDS Over-Current fault detection. When the LM5060 is enabled under normal operating conditions the timer capacitor will begin charging at a 6 μA (typical) rate while simultaneously charging the gate of the external MOSFET at a 24 μA (typical) rate. The gateto-source voltage (VGS) of the external MOSFET is expected to reach the 5V (typical) threshold before the timer capacitor has charged to the VTMRH threshold (2V typical) in order to avoid being shutdown. While VGS is less than the typical 5V threshold (VGATE-TH), the VDS start-up fault delay time is calculated from: VDS Fault Delay = VTIMERH x CTIMER ITIMERL where • ITMRL is typically 6 μA and VTMRH is typically 2V (3) If the CTIMER value is 68 nF (0.068μF) the VGS start-up fault delay time would typically be: VDS Fault Delay = ((2V x 0.068 μF) / 6 μA) = 23 ms (4) When the LM5060 has successfully completed the start-up sequence by reaching a VGS of 5V within the fault delay time set by the timer capacitor (CTIMER), the capacitor is quickly discharged to 300mV (typical) and the charge current is increased to 11 μA (typical) while the gate of the external MOSFET is continued to be charge at a 24 μA (typical) rate. The external MOSFET may not be fully enhanced at this point in time and some additional time may be needed to allow the gate-to-source voltage (VGS) to charge to a higher value. The drain-to-source voltage (VDS) of the external MOSFET must fall below the VDSTH threshold set by RS and ISENSE before the timer capacitor has charged to the VTMRH threshold (2V typical) to avoid a fault. When VGS is greater than the typical 5V threshold (VGATE-TH), the VDS transition fault delay time is calculated from: VDS Fault Delay = (VTIMERH - VTMRL) x CTIMER ITIMERH where • • • ITMRH is typically 11 μA VTMRH is typically 2V VTMRL is typically 300 mV (5) If the CTIMER value is 68 nF(0.068 μF) the VDS transition fault delay time would typically be: VDS Fault Delay = (((2V-0.3V) x 0.068 μF) / 11 μA) = 10 ms (6) Should a subsequent load current surge trip the VDS Fault Comparator, the timer capacitor discharge transistor turns OFF and the 11 μA (typical) current source begins linearly charging the timer capacitor. If the surge current, with the detected excessive VDS voltage, lasts long enough for the timer capacitor to charge to the timing comparator threshold (VTMRH) of typically 2V, the LM5060 will immediately discharge the MOSFET gate and latch the MOSFET off. The VDS fault delay time during an Over-Current event is calculated from: VDS Fault Delay = VTIMERH x CTIMER ITIMERH where • • ITMRH is typically 11 μA VTMRH is typically 2V (7) If the CTIMER value is 68 nF(0.068 μF) the VDS Over-Current fault delay time would typically be: VDS Fault Delay = ((2V x 0.068 μF) / 11 μA) = 12 ms 18 Submit Documentation Feedback (8) Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 LM5060 www.ti.com SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 Since a single capacitor is used to set the delay time for multiple fault conditions, it is likely that some compromise will need to be made between a desired delay time and a practical delay time. MOSFET SELECTION The external MOSFET (Q1) selection should be based on the following criteria: • The BVDSS rating must be greater than the maximum system voltage (VIN), plus ringing and transients which can occur at VIN when the circuit is powered on or off. • The maximum transient current rating should be based on the maximum worst case VDS fault current level. • MOSFETs with low threshold voltages offer the advantage that during turn on they are more likely to remain within their safe operating area (SOA) because the MOSFET reaches the ohmic region sooner for a given gate capacitance. • The safe operating area (SOA) of the MOSFET device and the thermal properties should be considered relative to the maximum power dissipation possible during startup or shutdown. • RDS(ON) should be sufficiently low that the power dissipation at maximum load current ((IL(MAX))2 x RDS(ON)) does not increase the junction temperature above the manufacturer’s recommendation. • If the device chosen for Q1 has a maximum VGS rating less than 16V, an external zener diode must be added from gate to source to limit the applied gate voltage. The external zener diode forward current rating should be at least 80 mA to conduct the full gate pull-down current during fault conditions. INPUT and OUTPUT CAPACITORS Input and output capacitors are not necessary in all applications. Any current that the external MOSFET conducts in the on-state will decrease very quickly as the MOSFET turns off. All trace inductances in the design including wires and printed circuit board traces will cause inductive voltage kicks during the fast termination of a conducting current. On the input side of the LM5060 circuit this inductive kick can cause large positive voltage spikes, while on the output side, negative voltage spikes are generated. To limit such voltage spikes, local capacitance or clamp circuits can be used. The necessary capacitor value depends on the steady state input voltage level, the level of current running through the MOSFET, the inductance of circuit board traces as well as the transition speed of the MOSFET. Since the exact amount of trace inductance is hard to predict, careful evaluation of the circuit board is the best method to optimize the input or output capacitance or clamp circuits. UVLO, OVP The UVLO and OVP thresholds are programmed to enable the external MOSFET (Q1) when the input supply voltage is within the desired operating range. If the supply voltage is low enough that the voltage at the UVLO pin is below the UVLO threshold, Q1 is switched off by a 2.2 mA (typical) current sink at the GATE pin, denying power to the load. The UVLO threshold has approximately 180 mV of hysteresis. If the supply voltage is high enough that the voltage at the OVP pin is above the OVP threshold, the GATE pin is pulled low with a 80 mA current sink. Hysteresis is provided for each threshold. The OVP threshold has approximately 240 mV of hysteresis. Option A: The configuration shown in Figure 29 requires three resistors (R1, R2, and R3) to set the thresholds. Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 19 LM5060 SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 www.ti.com VIN VIN LM5060 R1 UVLOTH 1.60V UVLO UVLOBIAS 5.5 PA R2 OVP OVPTH 2.00V R3 Figure 29. UVLO and OVP Thresholds Set By R1, R2 and R3 The procedure to calculate the resistor values is as follows: 1. Select R1 based on current consumption allowed in the resistor divider, including UVLOBIAS, and consideration of noise sensitivity. A value less than 100 kΩ is recommended, with lower values providing improved immunity to variations in ULVOBIAS. 2. Calculate R3 with the following formula: UVLOTH x R1 R3 = + R1 VINMIN - UVLOTH - (UVLOBIAS x R1) VINMAX UVLOBIAS x R1 OVPTH OVPTH (9) 3. Calculate R2 with the following formula: R2 = UVLOBIAS x R1 x R3 R3 x VINMAX - R3 - R1 OVPTH OVPTH (10) VINMIN is the minimum and VINMAX is the maximum input voltage of the design specification. All other variables can be found in the Electrical Characteristics table of this document. To calculate the UVLO lower threshold including its hysteresis for falling VIN, use (UVLOTH-UVLOHYS) instead of UVLOTH in the formulas above. To calculate the OVP lower threshold including hysteresis for falling VIN, use (OVPTH-OVPHYS) instead of OVPTH. With three given resistors R1, R2, and R3, the thresholds can be calculated with the formulas below: VINMAX = R1 x VINMIN = OVPTH R3 UVLOTH R2 + R3 + UVLOBIAS + R2 x OVPTH R3 + OVPTH + UVLOBIAS x R1 + UVLOTH (11) Also in these two formulas, the respective lower threshold value including the hysteresis is calculated by using (UVLOTH-UVLOHYS) instead of UVLOTH, and (OVPTH-OVPHYS) instead of OVPTH. The worst case thresholds, over the operating temperature range, can be calculated using the respective min and max values in bold font in the Electrical Characteristics . Option B: UVLO and OVP can be independently adjusted using two resistor dividers as shown in Figure 30. 20 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 LM5060 www.ti.com SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 VIN VIN LM5060 R10 UVLO R8 UVLOTH 1.60V UVLOBIAS 5.5 PA R11 OVP OVPTH 2.00V R9 Figure 30. Programming the Thresholds with Resistors R8-R11 Choose the upper UVLO thresholds to ensure operation down to the lowest required operating input voltage (VINMIN). Select R11 based on resistive divider current consumption and noise sensitivity. A value less than 100 kΩ is recommended, with lower values providing improved immunity to variations in ULVOBIAS. R10 = VINMIN - UVLOTH UVLOBIAS + UVLOTH R11 (12) To calculate the UVLO low threshold including its hysteresis, use (UVLOTH-UVLOHYS) instead of UVLOTH in the formula above. Choose the lower OVP threshold to ensure operation up to the highest VIN voltage required (VINMAX). Select R9 based on resistive divider current consumption A value less than 100 kΩ is recommended. R8 = R9 x VINMAX - OVPTH OVPTH (13) To calculate the OVP low threshold including hysteresis, use (OVPTH-OVPHYS) instead of OVPTH. Where the R9R11 resistor values are known, the threshold voltages are calculated from the following: VINMAX = OVPTH + R8 x OVPTH R9 VINMIN = UVLOTH + R10 x UVLOBIAS + UVLOTH R11 (14) Also in these two formulas, the respective low value including the threshold hysteresis is calculated by using (UVLOTH-UVLOHYS) instead of UVLOTH and (OVPTH-OVPHYS) instead of OVPTH. The worst case thresholds, over the operating temperature range, can be calculated using the respective minimum and maximum values in bold font in the Electrical Characteristics. Option C: The OVP function can be disabled by grounding the OVP pin. The UVLO thresholds are set as described in Figure 30. POWER GOOD INDICATOR A resistor between a supply voltage and the nPGD pin limits the current into the nPGD pin in a logic low condition. A nPGD pin sink current in the range of 1 mA to 5 mA is recommended. The example in Figure 31 connects the nPGD pull-up resistor R4 to the VIN pin. Any positive supply voltage less than 65V may be used instead of VIN. Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 21 LM5060 SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 www.ti.com VIN LM5060 R4 nPGD VDS fault signal Status GND Figure 31. Circuitry at the nPGD Pin INPUT BYPASS CAPACITOR Some input capacitance from the VIN pin to the GND pin may be necessary to filter noise and voltage spikes from the VIN rail. If the current through Q1 in Figure 21 is very large a sudden shutdown of Q1 will cause an inductive kick across the line input and pc board trace inductance which could damage the LM5060. In order to protect the VIN pin as well as SENSE, OVP, UVLO, and nPGD pins from harm, a larger bulk capacitor from VIN to GND may be needed to reduce the amplitude of the voltage spikes. Protection diodes or surge suppressors may also be used to limit the exposure of the LM5060 pins to voltages below their maximum operating ratings. THERMAL CONSIDERATIONS In normal operation the LM5060 dissipates very little power so that thermal design may not be very critical. The power dissipation is typically the 2 mA input current times the input voltage. If the application is driving a large capacitive load application, upon shutdown of the LM5060, the load capacitor may partially, or fully, discharge back through the LM5060 circuitry if no other loads consume the energy of the pre-charged load capacitor. One application example where energy is dissipated by the LM5060 is a motor drive application with a large capacitor load. When the LM5060 is turned off, the motor might also turn off such that total residual energy in the load capacitor is conducted through the OUT pin to ground. The power dissipated within the LM5060 is determined by the discharge current of 80 mA and the voltage on the load capacitor. LARGE LOAD CAPACITANCE Figure 32 shows an application with a large load capacitance CL. Assume a worst case turn off scenario where Vin remains at the same voltage as CL and RL is a high impedance. The body diode of Q1 will not conduct any current and all the charge on CL is dissipated through the LM5060 internal circuitry. The dotted line in Figure 32 shows the path of this current flow. Initially the power dissipated by the LM5060 is calculated with the formula: P = IGATE-FLT x VOUT where • IGATE-FLT is the sink current of the LM5060 gate control (15) In applications with a high input voltage and very large output capacitance, the discharge current can be limited by an additional discharge resistor RO in series with the OUT pin as shown in Figure 33. This resistor will influence the current limit threshold, so the value of RS will need to be readjusted. 22 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 LM5060 www.ti.com SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 VIN VOUT Q1 CL RL RS GATE SENSE OUT Fault OFF IGATE-FLT 80 mA GND LM5060 Figure 32. Discharge Path of Possible Load Capacitor In applications exposed to reverse polarity on the input and a large load capacitance on the output, a current limiting resistor in series with the OUT pin is required to protect the LM5060 OUT pin from reverse currents exceeding 25 mA. Figure 33 shows the resistor RO in the trace to the OUT pin. VIN VOUT Q1 CL RS RL RO GATE SENSE OUT Fault OFF IGATE-FLT 80 mA GND LM5060 Figure 33. Current Limiting Resistor RO for Special Cases If a RO resistor in the OUT path is used, the current sensing will become less accurate since RO has some variability as well as the current into the OUT pin. The OUT pin current is specified in the Electrical Characteristics section as IOUT-EN. A RO resistor design compromise for protection of the OUT pin and a maintaining VDS sensing accuracy can be achieved. See the REVERSE POLARITY PROTECTION WITH A RESISTOR for more details on how to calculate a reasonable RO value. REVERSE POLARITY PROTECTION WITH DIODES Figure 34 shows the LM5060 in an automotive application with reverse polarity protection. The second N-channel MOSFET Q2 is used to prevent the body diode of Q1 from conducting in a reverse VIN polarity situation. The zener diode D3 is used to limit VIN voltage transients which will occur when Q1 and Q2 are shut off quickly. In some applications the inductive kick is handled by input capacitors and D3 can be omitted. In reverse polarity protected applications, the input capacitors will see the reverse voltage. To avoid stressing input capacitors with reverse polarity, a transorb circuit implemented with D3 and D2 may be used. Diode D1 in Figure 34 protects the VIN pin in the event of reverse polarity. The resistor R1 protects the GATE pin from reverse currents exceeding 25 mA in the reverse polarity situation. This GATE resistor would slow down the shutdown of Q1 and Q2 dramatically. To prevent a slow turn off in fault conditions, D5 is added to bypass the current limiting resistor R1. Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 23 LM5060 SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 www.ti.com When Q1 and Q2 are turned on, R1 does not cause any delay because the GATE pin is driven with a 24 µA current source. D6, Q3 and R2 protect Q2 from VGS damage in the event of reverse input polarity. Diodes D5 and D7 are only necessary if the output load is highly capacitive. Such a capacitive load in combination with a high reverse polarity input voltage condition can exceed the power rating of the internal zener diode between OUT pin and GATE pin as well as the internal diode between the OUT pin and SENSE pin. External diodes D5 and D7 should be used in reverse polarity protected applications with large capacitive loads. Figure 34 Example Circuit Specification Operating Voltage Range 9V to 24V Current max 30A OVP setting 27V typical UVLO setting 9V typical Status Q1 75A, 40V D7 Q2 75A, 40V VOUT VIN R4 10 k: R3 12 k: R5 49.9 k: D3 36V D1 SENSE UVLO R6 5.62 k: R7 5.11 k: D6 GATE LM5060 OVP EN R1 2 k: nPGD VIN D2 Q3 0.6A, 40V D4 D5 OUT GND TIMER C2 100 nF R2 10 k: C1 68 nF Enable GND GND Figure 34. Application with Reverse Polarity Protection with Diodes for OUT Pin Protection REVERSE POLARITY PROTECTION WITH A RESISTOR An alternative to using external diodes to protect the LM5060 OUT pin in the reverse polarity input condition is a resistor in series with the OUT pin. Adding an OUT pin resistor may require modification of the resistor in series with the SENSE pin. A resistor in series with the OUT pin will limit the current through the internal zener diode between OUT and GATE as well as through the diode between OUT and SENSE. The value of these resistors should be calculated to limit the current through the diode across the input terminals of the VDS fault comparator to be no more than 4 mA. Figure 35 shows the internal circuitry relevant for calculating the values of the resistor RO in the OUT path to limit the current into the OUT pin to 4 mA. VOUT VIN LM5060 RS RO 25 mA max SENSE 4 mA max 1 k: 500: OUT IOUT-EN 8 PA ISENSE 16 PA VDS Fault Comparator Figure 35. Current Limiting Resistor for Negative SENSE Condition 24 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 LM5060 www.ti.com SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 When calculating the minimum RO resistor required to limit the current into the OUT pin, the internal current sources of 8 µA and 16 µA may be neglected. The following formulas can be used to calculate the resistor value RO(MIN) which is necessary to keep the IO current to less than 4 mA. Case A for situations where VOUT > VIN and reverse polarity situation is present. See Figure 35. VIN is negative, but the voltage at the SENSE pin can roughly be assumed to be 0.0V due to the internal diode from the SENSE pin to GND. RO(MIN) = VOUT - (4 mA x 1.5 k:) 4 mA (16) In this case, VIN also has to be limited to a negative voltage so that reverse current through the SENSE pin does not exceed 25 mA. RS(MIN) = VIN 25 mA (17) VIN VOUT LM5060 RS RO 4 mA max SENSE 1 k: 500: OUT IOUT-EN ISENSE 8 PA 16 PA VDS Fault Comparator Figure 36. Current Limiting Resistor in the OUT Path for OUT > SENSE Condition Case B for situations where VOUT > VIN and there is no reverse polarity situation present. See Figure 36. VIN is positive and VOUT is also positive, but VOUT is higher than VIN: RO(MIN) = (VOUT - VIN) - (RS + 1.5 k: 4 mA (18) In this case the voltage on the SENSE pin should not exceed 65V. Case C for situations where VOUT < VIN and both VIN and VOUT are positive as well. In such cases there is no risk of excessive OUT pin current. No current limiting resistors are necessary. Both the SENSE and OUT voltages should be limited to less than 65V. VIN VOUT LM5060 RS RO 25 mA max SENSE 1 k: 500: ISENSE OUT IOUT-EN 16 PA 8 PA VDS Fault Comparator Figure 37. Current Limiting Resistor for Negative OUT Conditions Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 25 LM5060 SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 www.ti.com Case D for situations where VOUT < VIN, while VOUT is negative and VIN is positive. See Figure 37. RO needs to be selected to protect the OUT pin from currents exceeding 25 mA. RO(MIN) = VOUT 25 mA (19) FAULT DETECTION WITH RS AND RO Figure 38 shows an example circuit where the OUT pin is protected against a reverse battery situation with a current limiting resistor RO. When using resistor RO in the OUT pin path, the resistor RS has to be selected taking the RO resistor into account. The LM5060 monitors the VDS voltage of an external N-Channel MOSFET. The VDS fault detection voltage is the drain to source voltage threshold (VDSTH). The formula below calculates a proper RS resistor value for a desired VDSTH taking into account the voltage drop across the RO resistor. RS = VDSTH RO x IOUT-EN VOFFSET + ISENSE ISENSE ISENSE (20) VOFFSET is the offset voltage between the SENSE pin and the OUT pin, ISENSE is the threshold programming current, and IOUT-EN is the OUT pin bias current. When RS and RO have been selected, the following formula can be used for VDSTH min and max calculations: VDSTH = ISENSE x RS - RO + VOFFSET IRATIO (21) The MOSFET drain-to-source current threshold is: IDSTH = VDSTH RDS(ON) where • RDS(ON) is the on resistance of the pass element Q1 in Figure 21 (22) CIRCUIT EXAMPLE OF REVERSE POLARITY PROTECTION WITH RESISTOR Figure 38 shows an example circuit which is protected against reverse polarity using resistor R8 instead of the diodes D5 and D7 of Figure 34. Figure 38 Example Circuit Specification Operating Voltage Range 9V to 24V Current max 30A OVP setting 27V typical UVLO setting 9V typical Q1 75A, 40V VIN D R3 12 k: D2 R5 49.9 k: D VOUT Q3 0.6A, 40V D1 R1 2 k: nPGD VIN D5 GATE UVLO LM5060 R6 5.62 k: OUT OVP EN Enable S D4 SENSE R7 5.11 k: S R4 10 k: Status D3 36V Q2 75A, 40V C2 100 nF GND TIMER R8 10 k: C1 68 nF R2 10 k: GND GND Figure 38. Application with Reverse Polarity Protection with a Resistor for OUT Pin Protection 26 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 LM5060 www.ti.com SNVS628F – OCTOBER 2009 – REVISED APRIL 2013 REVISION HISTORY Changes from Revision E (April 2013) to Revision F • Page Changed layout of National Data Sheet to TI format .......................................................................................................... 26 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated Product Folder Links: LM5060 27 PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) LM5060MM/NOPB ACTIVE VSSOP DGS 10 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SXAB LM5060MMX/NOPB ACTIVE VSSOP DGS 10 3500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SXAB LM5060Q1MM/NOPB ACTIVE VSSOP DGS 10 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SZAB LM5060Q1MMX/NOPB ACTIVE VSSOP DGS 10 3500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SZAB (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 OTHER QUALIFIED VERSIONS OF LM5060, LM5060-Q1 : • Catalog: LM5060 • Automotive: LM5060-Q1 NOTE: Qualified Version Definitions: • Catalog - TI's standard catalog product • Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 24-Apr-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM5060MM/NOPB VSSOP DGS 10 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM5060MMX/NOPB VSSOP DGS 10 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM5060Q1MM/NOPB VSSOP DGS 10 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM5060Q1MMX/NOPB VSSOP DGS 10 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 24-Apr-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM5060MM/NOPB VSSOP DGS 10 1000 210.0 185.0 35.0 LM5060MMX/NOPB VSSOP DGS 10 3500 367.0 367.0 35.0 LM5060Q1MM/NOPB VSSOP DGS 10 1000 203.0 190.0 41.0 LM5060Q1MMX/NOPB VSSOP DGS 10 3500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated