ASM3P2760A Peak EMI Reducing Solution Features The ASM3P2760A uses the most efficient and optimized modulation profile approved by the FCC and is implemented by using a proprietary all digital method. • Generates an EMI optimized clock signal at the output. • Integrated loop filter components. The ASM3P2760A modulates the output of a single PLL in order to “spread” the bandwidth of a synthesized clock, and more importantly, decreases the peak amplitudes of its harmonics. This results in significantly lower system EMI compared to the typical narrow band signal produced by oscillators and most frequency generators. Lowering EMI by increasing a signal’s bandwidth is called ‘spread spectrum clock generation.’ • Operates with a 3.3V / 2.5V Supply. • Operating current less than 4mA. • CMOS design. • Input frequency range: 6MHz to 12MHz for 2.5V. 6MHz to 13MHz for 3.3V. • Generates a 1X low EMI spread spectrum clock of the input frequency. • Frequency deviation: ±0.65% @ 8MHz. Applications • Available in 6L-TSOP (6L-TSOT-23) Package. The ASM3P2760A is targeted towards all portable devices like MP3 players and digital still cameras. Product Description The ASM3P2760A is a versatile spread spectrum frequency modulator designed specifically for a wide range of clock frequencies. The ASM3P2760A reduces electromagnetic interference (EMI) at the clock source, allowing system wide reduction of EMI of all clock dependent signals. The ASM3P2760A allows significant system cost savings by reducing the number of circuit board layers, ferrite beads and shielding that are traditionally required to pass EMI regulations. Key Specifications Description Specification Supply voltages VDD = 3.3V / 2.5V Cycle-to-Cycle Jitter ±200pS (typ) Output Duty Cycle 45/55% Modulation Rate Equation FIN/256 Frequency Deviation ±0.65% @ 8MHz Block Diagram VDD PD PLL Modulation XIN XOUT Crystal Oscillator Frequency Divider Feedback Divider Phase Detector Loop Filter VCO Output Divider ModOUT VSS ©2010 SCILLC. All rights reserved. JANUARY 2010 – Rev. 2 Publication Order Number: ASM3P2760/D ASM3P2760A Pin Configuration (6L-TSOP Package) PD 1 XOUT 2 ASM3P2760A XIN / CLKIN 3 6 VSS 5 ModOUT 4 VDD Pin Description Pin# Pin Name 1 Type PD Description I Power-down control pin. Pull low to enable power-down mode. Connect to VDD if not used. 2 XOUT O Crystal connection. If using an external reference, this pin must be left unconnected. 3 XIN / CLKIN I Crystal connection or external reference frequency input. This pin has dual functions. It can be connected either to an external crystal or an external reference clock. 4 VDD P Power supply for the entire chip. 5 ModOUT O Spread spectrum clock output. 6 VSS P Ground connection. Absolute Maximum Ratings Symbol VDD, VIN TSTG Parameter Rating Unit Voltage on any pin with respect to Ground -0.5 to +4.6 V Storage temperature -65 to +125 °C Ts Max. Soldering Temperature (10 sec) 260 °C TJ Junction Temperature 150 °C 2 KV TDV Static Discharge Voltage (As per JEDEC STD22- A114-B) Note: These are stress ratings only and are not implied for functional use. Exposure to absolute maximum ratings for prolonged periods of time may affect device reliability. Operating Conditions Parameter VDD Description Supply Voltage Min Max Unit 2.375 3.6 V 0 70 °C TA Operating Temperature (Ambient Temperature) CL Load Capacitance 15 pF CIN Input Capacitance 7 pF Rev. 2 | Page 2 of 7 | www.onsemi.com ASM3P2760A DC Electrical Characteristics for 2.5V Supply Symbol Parameter VIL Min Typ Max Unit V Input low voltage VSS-0.3 0.8 VIH Input high voltage 2.0 VDD+0.3 V IIL Input low current -35 µA IIH Input high current 35 µA IXOL XOUT output low current (@ 0.5V, VDD = 2.5V) 3 mA IXOH XOUT output high current (@ 1.8V, VDD = 2.5V) 3 mA VOL Output low voltage (VDD = 2.5V, IOL = 8mA) VOH Output high voltage (VDD = 2.5V, IOH = 8mA) 0.6 IDD Static supply current ICC Dynamic supply current (2.5V, 8MHz and no load) 1.8 1 VDD tON 10 Operating Voltage 2.5 2.375 Power-up time (first locked cycle after power-up) ZOUT V V 2.5 2 Output impedance 50 µA mA 2.625 V 5 mS - Ω Notes: 1. XIN / CLKIN pin and PD pin are pulled low. 2. VDD and XIN / CLKIN input are stable, PD pin is made high from low. AC Electrical Characteristics for 2.5V Supply Symbol CLKIN ModOUT fd Min Typ Max Unit Input frequency 6 12 MHz Output frequency 6 12 MHz Input Frequency = 6MHz ±1.0 Input Frequency = 12MHz ±0.45 Frequency Deviation % 1 Output rise time (measured from 0.7V to 1.7V) 0.4 1.2 1.4 nS 1 Output fall time (measured from 1.7V to 0.7V) 0.4 0.9 1.1 nS tLH tHL Parameter tJC Jitter (cycle-to-cycle) tD Output duty cycle ±200 45 Note: 1. tLH and tHL are measured into a capacitive load of 15pF. Rev. 2 | Page 3 of 7 | www.onsemi.com 50 pS 55 % ASM3P2760A DC Electrical Characteristics for 3.3V Supply Symbol Parameter VIL Min Typ Max Unit V Input low voltage VSS-0.3 0.8 VIH Input high voltage 2.0 VDD+0.3 V IIL Input low current -35 µA IIH Input high current 35 µA IXOL XOUT output low current (@ 0.4V, VDD = 3.3V) 3 mA IXOH XOUT output high current (@ 2.5V, VDD = 3.3V) 3 mA VOL Output low voltage (VDD = 3.3 V, IOL = 8mA) VOH Output high voltage (VDD = 3.3 V, IOH = 8mA) 0.4 IDD Static supply current ICC Dynamic supply current (3.3V, 8MHz and no load) 2.5 1 VDD 10 Operating Voltage tON µA 3.0 2.7 mA 3.3 2 Power-up time (first locked cycle after power up) ZOUT V V Output impedance 3.6 V 5 mS Ω 45 Notes: 1. XIN / CLKIN pin and PD pin are pulled low. 2. VDD and XIN / CLKIN input are stable; PD pin is made high from low. AC Electrical Characteristics for 3.3V Supply Symbol CLKIN ModOUT fd Min Typ Max Unit Input frequency 6 13 MHz Output frequency 6 13 MHz Input Frequency = 6MHz ±1.0 Input Frequency = 13MHz ±0.4 Frequency Deviation % 1 Output rise time (measured at 0.8V to 2.0V) 0.5 1.3 1.5 nS 1 Output fall time (measured at 2.0V to 0.8V) 0.4 1.0 1.2 nS tLH tHL Parameter tJC Jitter (cycle-to-cycle) tD Output duty cycle ±200 45 Note: 1. tLH and tHL are measured into a capacitive load of 15pF. Rev. 2 | Page 4 of 7 | www.onsemi.com 50 pS 55 % ASM3P2760A Typical Crystal Specifications Fundamental AT cut parallel resonant crystal Nominal frequency 8MHz Frequency tolerance ± 50 ppm or better at 25°C Operating temperature range -25°C to +85°C Storage temperature -40°C to +85°C Load capacitance(CP) 18pF Shunt capacitance 7pF maximum ESR 25 Ω Note: Note: CL is Load Capacitance and Rx is used to prevent oscillations at overtone frequency of the Fundamental frequency. Typical Crystal Interface Circuit R Rx Crystal CL CL CL = 2*(CP – CS), Where CP = Load capacitance of crystal CS = Stray capacitance due to CIN, PCB, Trace etc. Typical Application Schematic VDD C1 0.1µF C2 2.2µF VDD ASM3P2760A Rs ModOUT VSS Rev. 2 | Page 5 of 7 | www.onsemi.com ModOUT Clock ASM3P2760A Package Information 6L-TSOP Package Dimensions Symbol Inches Min A Millimeters Max Min Max 0.04 1.00 A1 0.00 0.004 0.00 0.10 A2 0.033 0.036 0.84 0.90 b 0.012 0.02 0.30 0.50 H 0.005 BSC 0.127 BSC D 0.114 BSC 2.90 BSC B 0.06 BSC 1.60 BSC e 0.0374 BSC 0.950 BSC C 0.11 BSC 2.80 BSC L 0.0118 0.02 0.30 0.50 θ 0° 4° 0° 4° Rev. 2 | Page 6 of 7 | www.onsemi.com ASM3P2760A Ordering Information Part Number Marking ASM3P2760AF-06OR E4L Package Type Temperature 6L-TSOP(6L-TSOT-23), TAPE & REEL, Pb Free 0°C to +70°C A “microdot” placed at the end of last row of marking or just below the last row toward the center of package indicates Pb-free. Licensed under US Patent #5,488,627 and #5,631,921. Note: This product utilizes US Patent #6,646,463 Impedance Emulator Patent issued to PulseCore Semiconductor, dated 11-11-2003. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. U.S Patent Pending; Timing-Safe and Active Bead are trademarks of PulseCore Semiconductor, a wholly owned subsidiary of ON Semiconductor. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative