SURFACE MOUNT SUPER FAST RECTIFIER ESM1A THRU ESM1J VOLTAGE RANGE 50 to 600Volts FORWARD CURRENT 1.0 Ampere FEATURES • • • • • • DO-213AB For surface mounted applications Glass passivated chip junction Low leakage current Fast switchig Plastic package has underwrites laboratory flammability Classification 94V-0 High temperature soldering guaranteed 250℃/10 seconds at terminals MECHANICAL DATA • • • • Dimensions in inches and (millimeters) Case: molded plastic Polarity: band indicate cathode Mounting position: Any Weight: 0.12 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% SYMBOLS Maximum Repetitive Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T T=100℃ Peak Forward Surge Current 8.3ms single half sine wave superimposed on rated load (JEDEC Method) Maximum Instantaneous Forward Voltage at 1.0A TA = 25℃ Maximum DC Reverse Current at rated DC Blocking Voltage at TA = 125℃ Typical Reverse Recovery Time (NOTE 1) Typical Junction Capacitance (Note 2) Typical Thermal Resistance (Note 3) Operating and Storage Temperature Range VRRM VRMS VDC I(AV) ESM 1A 50 35 50 ESM 1B 100 70 100 ESM 1C 150 105 150 ESM 1D 200 140 200 1.0 IFSM VF ESM 1G 400 280 400 ESM 1J 600 420 600 30 095 Trr CJ RθJT TJ,TSTG 1.25 Notes: 1. Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A 2. Measured at 1.0MHz and applied reverse voltage of 4.0 Volts. 3. Thermal resistance Junction to terminal 6.0mm2 copper pads to each terminal. Web Site: www.cnmic.com UNITS Volts Volts Volts Amps Amps 5.0 100 35 15 40 -55 to +150 IR E-mail: [email protected] ESM 1E 300 210 300 1.7 Volts µA ns PF ℃/W ℃ SURFACE MOUNT SUPER FAST RECTIFIER ESM1A THRU ESM1J VOLTAGE RANGE 50 to 600Volts FOEWARD CURRENT 1.0 Ampere RATINGS AND CHARACTERISTIC CURVES ESM1A THRU ESM1J FIG.1-MAXMUM FORWARD CURRENT FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT DERATING CURVE 1.0 0.8 0.6 0.4 Resistive or Inductive Load 0.2 P.C.B Mounted 0.2x0.2"(5.0x5.0mm) Copper Pad Areas 0 80 90 100 110 120 130 140 150 PEAK FORWARD SURGE CURRENT,(A) AVERAGE FORWARD CURRENT(A) 1.2 30 8.3ms Single Half Sine-Wave (JEDEC Method)T =110° c T 25 20 15 10 5.0 0 1 10 100 NUMBER OF CYCLES AT 60 Hz FIG.4-TYPICAL REVERSE LEAKAGE CHARACTERISTICS 0.01 0.001 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE,(V) FIG.5-TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE,(pF) 60 T =25° J C Pulse Width=300us 1% Duty Cycle 50 40 30 20 10 0 0.1 1.0 10 100 INSTANTANEOUS REVERSE CURRENT,(uA) T J=25° C Pulse Width=300us 1% Duty Cycle TRANSIENT THERMAL IMPEDANCE(℃/W) ES M 1J M ES M1 0.1 A -1 D 1E -1 G 1.0 ES INSTANTANEOUS FORWARD CURRENT,(A) FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 5.0 1000 T J=125° C 100 10 T J=75° C 1.0 T =25° J C 0.1 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FIG.6-TRANSIENT THERMAL IMPEDANCE 100 Mounted on 0.20x0.27"(5.0x7.0mm) Copper Land Areas 10 1 0.1 1.0 10 100 T,PULSE DURATION(SEC.) REVRESE VOLTAGE,(V) E-mail: [email protected] Web Site: www.cnmic.com