JC Series 2:1 Wide Input Range Single and Dual Output 2 Watt DC/DC Converter FEATURES ● Low Cost ● 1500VDC Isolation ● Efficiency up to 81% ● Low Ripple and Noise ● MTBF > 1,000,000 Hours ● Internal SMT Construction ● UL 94V-0 Package Material ● 2:1 Wide Input Voltage Range ● Complies with EN55022 Class A ● Temperature Performance –40°C to +71°C SPECIFICATIONS: JC Series All specifications are based on 25oC, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. SPECIFICATION TEST CONDITIONS Min Nom Max Unit INPUT (Vin) Input Voltage Range Start Voltage Under Voltage Shutdown Input Surge Voltage (1000ms) Reverse Polarity Input Current Reflected Ripple Current Short Circuit Input Power Input Filter OUTPUT (Vo) Output Voltage Range Output Voltage Accuracy Output Voltage Balance Load Regulation Line Regulation Output Power Output Current Range Ripple & Noise (20MHz) Ripple & Noise (20MHz) Ripple & Noise (20MHz) Transient Recovery Time Transient Response Deviation Temperature Coefficient PROTECTION Over Power Protection Short Circuit Protection Input Fuse Recommendation 5V input models 12V input models 24V input models 48V input models 5V input models 12V input models 24V input models 48V input models 5V input models 12V input models 24V input models 48V input models 5V input models 12V input models 24V input models 48V input models All models 4.5 9 18 36 3.5 4.5 8 16 -0.7 -0.7 -0.7 -0.7 All models All models Over Line, Load, and Temperature 25% Load Step Change 25% Load Step Change 120 Wall Industries, Inc. 37 Industrial Drive Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 9 18 36 75 4.5 9 18 36 4 8.5 17 34 11 25 50 100 1 See Table 1500 Pi Filter See Table ±1.0 ±2.0 ±1.0 ±2.0 ±0.5 ±0.75 ±0.3 ±0.5 2 See Table 30 50 75 15 100 300 ±3 ±5 ±0.01 ±0.02 Dual Output, Balanced Loads Io = 25% to 100% Vin = Min to Max 5V input models 12V input models 24V input models 48V input models 5 12 24 48 4 7 12 24 3.5 6.5 11 22 VDC VDC VDC VDC VDC VDC VDC VDC VDC VDC VDC VDC VDC VDC VDC VDC A mW % % % % W mVpk-pk mVpk-pk mVrms μs % %/°C % Continuous 1000mA Slow-Blow Type 500mA Slow-Blow Type 250mA Slow-Blow Type 120mA Slow-Blow Type JC Series 2:1 Wide Input Range Single and Dual Output 2 Watt DC/DC Converter SPECIFICATION (CONTINUED) TEST CONDITIONS GENERAL Efficiency Switching Frequency Isolation Voltage Rated Isolation Voltage Test Isolation Resistance Isolation Capacitance Maximum Capacitive Load Internal Power Dissipation ENVIRONMENTAL Operating Temperature (Ambient) Operating Temperature (Case) Storage Temperature Lead Temperature Humidity Cooling MTBF PHYSICAL Weight Dimensions Case Material Min Nom Max See Table 300 60 seconds Flash Tested for 1 second 500VDC 100KHz, 1V 1500 1650 1000 250 420 See Table 1800 -40 -40 -40 1.5mm from case for 10 seconds MIL-HDBK-217F @ 25°C, Ground Benign +71 +90 +125 260 95 Free air convection 1,000,000 Hours Unit KHz VDC VDC MΩ pF mW °C °C °C °C % 0.13oz (3.75 grams) 24.0(L) x 13.7(W) x 8.0(H) mm Non-conductive black plastic OUTPUT VOLTAGE / CURRENT RATING CHART Model Number JC5S33-500 JC5S5-400 JC5S12-167 JC5S15-134 JC5D5-200 JC5D12-83 JC5D15-67 JC12S33-500 JC12S5-400 JC12S12-167 JC12S15-134 JC12D5-200 JC12D12-83 JC12D15-67 JC24S33-500 JC24S5-400 JC24S12-167 JC24S15-134 JC24D5-200 JC24D12-83 JC24D15-67 JC48S33-500 JC48S5-400 JC48S12-167 JC48S15-134 JC48D5-200 JC48D12-83 JC48D15-67 Output Voltage Input Voltage 5 VDC (4.5 – 9 VDC) 12VDC (9 – 18 VDC) 24VDC (18 – 36 VDC) 48VDC (36 – 75 VDC) 3.3 VDC 5 VDC 12 VDC 15 VDC ±5 VDC ±12 VDC ±15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC ±5 VDC ±12 VDC ±15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC ±5 VDC ±12 VDC ±15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC ±5 VDC ±12 VDC ±15 VDC Output Current Min Max 125mA 100mA 42mA 33mA ±50mA ±21mA ±17mA 125mA 100mA 42mA 33mA ±50mA ±21mA ±17mA 125mA 100mA 42mA 33mA ±50mA ±21mA ±17mA 125mA 100mA 42mA 33mA ±50mA ±21mA ±17mA 500mA 400mA 167mA 134mA ±200mA ±83mA ±67mA 500mA 400mA 167mA 134mA ±200mA ±83mA ±67mA 500mA 400mA 167mA 134mA ±200mA ±83mA ±67mA 500mA 400mA 167mA 134mA ±200mA ±83mA ±67mA Input Current (Typ) Reflected Ripple Current (Typ) No Load Max Load 40mA 20mA 10mA 8mA 471mA 548mA 534mA 582mA 667mA 615mA 598mA 184mA 217mA 209mA 220mA 242mA 224mA 226mA 96mA 109mA 109mA 108mA 119mA 112mA 110mA 49mA 57mA 53mA 55mA 62mA 57mA 57mA 100mA 25mA 15mA 10mA Wall Industries, Inc. 37 Industrial Drive Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 Efficiency (Typ) 70% 73% 75% 73% 64% 69% 71% 73% 77% 80% 80% 73% 78% 78% 72% 77% 80% 81% 74% 78% 80% 71% 73% 79% 79% 71% 77% 77% Max Capacitive Load 2200μF 1000μF 170μF 110μF 470μF 100μF 47μF 2200μF 1000μF 170μF 110μF 470μF 100μF 47μF 2200μF 1000μF 170μF 110μF 470μF 100μF 47μF 2200μF 1000μF 170μF 110μF 470μF 100μF 47μF JC Series 2:1 Wide Input Range Single and Dual Output 2 Watt DC/DC Converter NOTES 1. 2. 3. 4. Specifications typical at +25°C, resistive load, nominal input voltage, rated output current unless otherwise noted. Transient Recovery Time is measured to within 1% error band for a step change in output of 75% to 100%. Ripple and noise measured at 20MHz bandwidth. The JC Series requires a minimum load on the output to maintain specified regulation. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 5. All DC/DC converters should be externally fused on the front end for protection. 6. Other input and output voltages may be available, please contact factory. 7. Specifications subject to change without notice. BLOCK DIAGRAMS Input Voltage Transient Rating Wall Industries, Inc. 37 Industrial Drive Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 JC Series 2:1 Wide Input Range Single and Dual Output 2 Watt DC/DC Converter MECHANICAL DRAWING Tolerance: Millimeters X.X±0.25 X.XX±0.13 Inches X.XX±0.01 X.XXX±0.005 Pin: ±0.05 ±0.002 Pin 1 7 8 9 10 16 PIN CONNECTIONS Single Output Dual Output -Vin -Vin NC NC NC Common +Vout +Vout -Vout -Vout +Vin +Vin Wall Industries, Inc. 37 Industrial Drive Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 JC Series 2:1 Wide Input Range Single and Dual Output 2 Watt DC/DC Converter DESIGN & FEATURE CONSIDERATONS Input Source Impedance The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the power module. In applications where power is supplied over long lines and output loading is high, it may be necessary to use a capacitor at the input to ensure startup. By using a good quality low Equivalent Series Resistance (ESR < 1.0Ω at 100kHz) capacitor of 8.2μF for the 5V input devices, a 3.3μF for the 12V input devices, and a 1.5μF for the 24V and 48V devices. A capacitor mounted close to the power module helps ensure stability of the unit. Maximum Capacitive Load The JC Series has a limitation of maximum connected capacitance on the output. The power module may operate in current limiting mode during start-up, affecting the ramp-up and the startup time. The maximum capacitance can be found in the “Output Voltage / Current Rating Chart.” Over Current Protection To provide protection in a fault (output overload) condition, the unit is equipped with internal current limiting circuitry and can endure current limiting for an unlimited duration. At the point of current-limit inception, the unit shifts from voltage control to current control. The unit operates normally once the output current is brought back into its specified range. Thermal Considerations Many conditions affect the thermal performance of the power module, such as orientation, airflow over the module, and board spacing. To avoid exceeding the maximum temperature rating of the components inside the power module, the case temperature must be kept below 90°C. The derating curves are determined from measurements obtained in an experimental apparatus. Wall Industries, Inc. 37 Industrial Drive Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 JC Series 2:1 Wide Input Range Single and Dual Output 2 Watt DC/DC Converter Efficiency vs Input Voltage ( Single Output ) Efficiency vs Input Voltage ( Dual Output ) Efficiency vs Output Load ( Single Output ) Efficiency vs Output Load ( Dual Output ) Derating Curve Wall Industries, Inc. 37 Industrial Drive Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 JC Series 2:1 Wide Input Range Single and Dual Output 2 Watt DC/DC Converter TEST CONFIGURATIONS Input Reflected-Ripple Current Test Setup Input reflected-ripple current is measured with an inductor Lin (4.7uH) and Cin (220uF, ESR < 1.0Ω at 100 KHz) to simulate source impedance. Capacitor Cin offsets possible battery impedance. Current ripple is measured at the input terminals of the module. Measurement bandwidth is 0-500 KHz. Peak-to-Peak Output Noise Measurement Test Use a Cout 0.47uF ceramic capacitor. Scope measurement should be made by using a BNC socket, measurement bandwidth is 0-20MHz. Position the load between 50mm and 75mm from the DC/DC Converter. Wall Industries, Inc. 37 Industrial Drive Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 JC Series 2:1 Wide Input Range Single and Dual Output 2 Watt DC/DC Converter Output Ripple Reduction A good quality low ESR capacitor placed as close as possible across the load will give the best ripple and noise performance. To reduce output ripple, it is recommended to use 3.3uF capacitors at the output. COMPANY INFORMATION: Wall Industries, Inc. has created custom and modified units for over 40 years. Our in-house research and development engineers will provide a solution that exceeds your performance requirements on time and on budget. Our ISO9001-2000 certification is just one example of our commitment to producing a high quality, well documented product for our customers. Our past projects demonstrate our commitment to you, our customer. Wall Industries, Inc. has a reputation for working closely with its customers to ensure each solution meets or exceeds form, fit and function requirements. We will continue to provide ongoing support for your project above and beyond the design and production phases. Give us a call today to discuss your future projects. Contact Wall Industries for further information: Phone: Toll Free: Fax: E-mail: Web: Address: (603)778-2300 (888)587-9255 (603)778-9797 [email protected] www.wallindustries.com 5 Watson Brook Rd. Exeter, NH 03833 Wall Industries, Inc. 37 Industrial Drive Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797