MC10EP17, MC100EP17 3.3V / 5VECL Quad Differential Driver/Receiver Description The MC10/100EP17 is a 4-bit differential line receiver based on the EP17 device. The >3.0 GHz maximum frequency provided by the high frequency outputs makes the device ideal for buffering of very high speed oscillators. The VBB pin, an internally generated voltage supply, is available to this device only. For single-ended input conditions, the unused differential input is connected to VBB as a switching reference voltage. VBB may also rebias AC coupled inputs. When used, decouple VBB and VCC via a 0.01 mF capacitor and limit current sourcing or sinking to 0.5 mA. When not used, VBB should be left open. The design incorporates two stages of gain, internal to the device, making it an excellent choice for use in high bandwidth amplifier applications. Inputs of unused gates can be left open and will not affect the operation of the rest of the device. All VCC and VEE pins must be externally connected to power supply to guarantee proper operation. The 100 Series contains temperature compensation. • 220 ps Typical Propagation Delay • Maximum Frequency >3.0 GHz Typical • PECL Mode Operating Range: VCC = 3.0 V to 5.5 V • • • • • MARKING DIAGRAMS* 20 TSSOP−20 DT SUFFIX CASE 948E MCXXX EP17 ALYWG G 1 20 20 MCXXXEP17 AWLYYWWG 1 SO−20 DW SUFFIX CASE 751D Features • http://onsemi.com 1 20 with VEE = 0 V NECL Mode Operating Range: VCC = 0 V with VEE = −3.0 V to −5.5 V Open Input Default State Safety Clamp on Inputs Q Output Will Default LOW with Inputs Open or at VEE VBB Output Pb−Free Packages are Available* 1 QFN−20 MN SUFFIX CASE 485E XXXX EP17 ALYWG G XXX = 10 or 100 A = Assembly Location L, = Assembly Lot WL = Wafer Lot Y, YY = Year W, WW = Work Week G or G = Pb−Free Package (Note: Microdot may be in either location) *For additional marking information, refer to Application Note AND8002/D. ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 8 of this data sheet. *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. © Semiconductor Components Industries, LLC, 2006 December, 2006 − Rev. 7 1 Publication Order Number: MC10EP17/D MC10EP17, MC100EP17 VCC Q0 Q0 Q1 Q1 Q2 Q2 Q3 Q3 VEE 20 19 18 17 16 15 14 13 12 11 Table 1. PIN DESCRIPTION 1 2 3 4 5 6 7 8 9 10 VCC D0 D0 D1 D1 D2 D2 D3 D3 VBB PIN FUNCTION D[0:3]*, D[0:3]* ECL Differential Data Inputs Q[0:3], Q[0:3] ECL Differential Data Outputs VBB Reference Voltage Output VCC Positive Supply VEE Negative Supply EP Exposed Pad * Pins will default LOW when left open. Figure 1. 20−Lead Pinout (Top View) and Logic Diagram Exposed Pad D0 VCC VCC Q0 Q0 20 19 18 17 16 D0 1 15 Q1 D1 2 14 Q1 D1 3 D2 4 12 Q2 D2 5 11 Q3 MC10/100EP17 6 NOTE: 7 8 9 13 Q2 10 D3 D3 VBB VEE Q3 The Exposed Pad (EP) on package bottom must be attached to a heat−sinking conduit. The Exposed Pad may only be electrically connected to VEE. Figure 1. QFN−20 Pinout (Top View) Table 2. ATTRIBUTES Characteristics Value Internal Input Pulldown Resistor 75 kW Internal Input Pullup Resistor ESD Protection N/A Human Body Model Machine Model Charged Device Model Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1) SOIC−20 TSSOP−20 QFN−20 Flammability Rating Oxygen Index: 28 to 34 Transistor Count > 2 kV > 100 V > 2 kV Pb Pkg Pb−Free Pkg Level 1 Level 1 N/A Level 1 Level 3 Level 1 UL 94 V−0 @ 0.125 in 259 Devices Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 1. For additional information, see Application Note AND8003/D. http://onsemi.com 2 MC10EP17, MC100EP17 Table 3. MAXIMUM RATINGS Symbol Rating Unit VCC PECL Mode Power Supply Parameter VEE = 0 V Condition 1 Condition 2 6 V VEE NECL Mode Power Supply VCC = 0 V −6 V VI PECL Mode Input Voltage NECL Mode Input Voltage VEE = 0 V VCC = 0 V 6 −6 V V Iout Output Current Continuous Surge 50 100 mA mA IBB VBB Sink/Source ± 0.5 mA TA Operating Temperature Range −40 to +85 °C Tstg Storage Temperature Range −65 to +150 °C qJA Thermal Resistance (Junction−to−Ambient) 0 lfpm 500 lfpm 20 TSSOP 20 TSSOP 140 100 °C/W °C/W qJC Thermal Resistance (Junction−to−Case) Standard Board 20 TSSOP 23 to 41 °C/W qJA Thermal Resistance (Junction−to−Ambient) 0 lfpm 500 lfpm 20 SOIC 20 SOIC 90 60 °C/W °C/W qJC Thermal Resistance (Junction−to−Case) Standard Board 20 SOIC 30 to 35 °C/W qJA Thermal Resistance (Junction−to−Ambient) 0 lfpm 500 lfpm QFN−20 QFN−20 47 33 °C/W °C/W qJC Thermal Resistance (Junction−to−Case) Standard Board QFN−20 18 °C/W Tsol Wave Solder 265 265 °C VI v VCC VI w VEE Pb Pb−Free Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Table 4. 10EP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 2) −40°C Symbol Characteristic Min Typ 25°C Max Min Typ 85°C Max Min Typ Max Unit IEE Power Supply Current 42 50 65 44 52 66 46 54 68 mA VOH Output HIGH Voltage (Note 3) 2165 2290 2415 2230 2355 2480 2290 2415 2540 mV VOL Output LOW Voltage (Note 3) 1365 1490 1615 1430 1555 1680 1490 1615 1740 mV VIH Input HIGH Voltage (Single−Ended) 2090 2415 2155 2480 2215 2540 mV VIL Input LOW Voltage (Single−Ended) 365 1690 1430 1755 1490 1815 mV VBB Output Voltage Reference 1790 1990 1855 2055 1915 2115 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 4) 3.3 2.0 3.3 2.0 3.3 V IIH Input HIGH Current 150 mA IIL Input LOW Current 1890 2.0 150 0.5 1955 150 0.5 0.5 2015 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 2. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to −2.2 V. 3. All loading with 50 W to VCC − 2.0 V. 4. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. http://onsemi.com 3 MC10EP17, MC100EP17 Table 5. 10EP DC CHARACTERISTICS, PECL VCC = 5.0 V, VEE = 0 V (Note 5) Symbol IEE Characteristic Power Supply Current Min −40°C Typ Max Min 25°C Typ Max Min 85°C Typ Max 42 50 65 44 52 66 46 54 68 Unit mA VOH Output HIGH Voltage (Note 6) 3865 3990 4115 3930 4055 4180 3990 4115 4240 mV VOL Output LOW Voltage (Note 6) 3065 3190 3315 3130 3255 3380 3190 3315 3440 mV VIH Input HIGH Voltage (Single−Ended) 3790 4115 3855 4180 3915 4240 mV VIL Input LOW Voltage (Single−Ended) 3065 3390 3130 3455 3190 3515 mV VBB Output Voltage Reference 3490 3690 3555 3755 3615 3815 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 7) 5.0 2.0 5.0 2.0 5.0 V IIH Input HIGH Current 150 mA IIL Input LOW Current 3590 2.0 3655 150 3715 150 0.5 0.5 0.5 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 5. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to −0.5 V. 6. All loading with 50 W to VCC − 2.0 V. 7. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Table 6. 10EP DC CHARACTERISTICS, NECL VCC = 0 V; VEE = −5.5 V to −3.0 V (Note 8) Min −40°C Typ Max Min 25°C Typ Max Min 85°C Typ Max 42 50 65 44 52 66 46 54 68 Unit mA Output HIGH Voltage (Note 9) −1135 −1010 −885 −1070 −945 −820 −1010 −885 −760 mV Output LOW Voltage (Note 9) −1935 −1810 −1685 −1870 −1745 −1620 −1810 −1685 −1560 mV VIH Input HIGH Voltage (Single−Ended) −1210 −885 −1145 −820 −1085 −760 mV VIL Input LOW Voltage (Single−Ended) −1935 −1610 −1870 −1545 −1810 −1485 mV VBB Output Voltage Reference −1510 −1310 −1445 −1245 −1385 −1185 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 10) 0.0 V IIH Input HIGH Current 150 mA IIL Input LOW Current Symbol IEE Characteristic Power Supply Current VOH VOL −1410 VEE + 2.0 0.0 VEE + 2.0 150 0.5 −1345 0.0 VEE + 2.0 150 0.5 −1285 0.5 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 8. Input and output parameters vary 1:1 with VCC. 9. All loading with 50 W to VCC − 2.0 V. 10. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. http://onsemi.com 4 MC10EP17, MC100EP17 Table 7. 100EP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 11) −40°C 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 47 55 63 50 58 66 54 62 70 mA Output HIGH Voltage (Note 12) 2155 2280 2405 2155 2280 2405 2155 2280 2405 mV VOL Output LOW Voltage (Note 12) 1355 1480 1605 1355 1480 1605 1355 1480 1605 mV VIH Input HIGH Voltage (Single−Ended) 2075 2420 2075 2420 2075 2420 mV VIL Input LOW Voltage (Single−Ended) 1355 1675 1355 1675 1355 1675 mV VBB Output Voltage Reference 1775 1975 1775 1975 1775 1975 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 13) 3.3 2.0 3.3 2.0 3.3 V IIH Input HIGH Current 150 mA IIL Input LOW Current Symbol Characteristic IEE Power Supply Current VOH 1875 2.0 1875 150 0.5 1875 150 0.5 0.5 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 11. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to −2.2 V. 12. All loading with 50 W to VCC − 2.0 V. 13. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Table 8. 100EP DC CHARACTERISTICS, PECL VCC = 5.0 V, VEE = 0 V (Note 14) −40°C 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 47 55 63 50 58 66 54 62 70 mA Output HIGH Voltage (Note 15) 3855 3980 4105 3855 3980 4105 3855 3980 4105 mV VOL Output LOW Voltage (Note 15) 3055 3180 3305 3055 3180 3305 3055 3180 3305 mV VIH Input HIGH Voltage (Single−Ended) 3775 4120 3775 4120 3775 4120 mV VIL Input LOW Voltage (Single−Ended) 3055 3375 3055 3375 3055 3375 mV VBB Output Voltage Reference 3475 3675 3475 3675 3475 3675 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 16) 5.0 2.0 5.0 2.0 5.0 V IIH Input HIGH Current 150 mA IIL Input LOW Current Symbol Characteristic IEE Power Supply Current VOH 3575 2.0 150 0.5 3575 150 0.5 0.5 3575 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 14. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to −0.5 V. 15. All loading with 50 W to VCC − 2.0 V. 16. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. http://onsemi.com 5 MC10EP17, MC100EP17 Table 9. 100EP DC CHARACTERISTICS, NECL VCC = 0 V; VEE = −5.5 V to −3.0 V (Note 17) −40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 47 55 63 50 58 66 54 62 70 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 18) −1145 −1020 −895 −1145 −1020 −895 −1145 −1020 −895 mV VOL Output LOW Voltage (Note 18) −1945 −1820 −1695 −1945 −1820 −1695 −1945 −1820 −1695 mV VIH Input HIGH Voltage (Single−Ended) −1225 −880 −1225 −880 −1225 −880 mV VIL Input LOW Voltage (Single−Ended) −1945 −1625 −1945 −1625 −1945 −1625 mV VBB Output Voltage Reference −1525 −1325 −1525 −1325 −1525 −1325 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 19) 0.0 V IIH Input HIGH Current 150 mA IIL Input LOW Current −1425 VEE + 2.0 0.0 −1425 VEE + 2.0 150 0.5 0.0 −1425 VEE + 2.0 150 0.5 0.5 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 17. Input and output parameters vary 1:1 with VCC. 18. All loading with 50 W to VCC − 2.0 V. 19. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Table 10. AC CHARACTERISTICS VCC = 0 V; VEE = −3.0 V to −5.5 V or VCC = 3.0 V to 5.5 V; VEE = 0 V (Note 20) −40°C Symbol Min Characteristic fmax Maximum Frequency (Figure 2) tPLH, tPHL Propagation Delay to Output Differential 10 Series 100 Series tJITTER CLOCK Random Jitter (RMS) @ v 1.0 GHz @ v 1.5 GHz @ v 2.0 GHz @ v 2.5 GHz @ v 3.0 GHz VPP Input Voltage Swing (Differential Configuration) tr tf Output Rise/Fall Times (20% − 80%) Typ 25°C Max Min >3 Q, Q 125 150 Typ 85°C Max Min >3 200 220 275 300 0.132 0.143 0.148 0.129 0.129 0.2 0.3 0.3 0.3 0.3 150 800 1200 100 160 220 150 180 Typ Max >3 220 250 300 320 0.147 0.159 0.146 0.131 0.142 0.2 0.3 0.3 0.3 0.3 150 800 1200 100 170 230 200 200 Unit GHz ps 260 290 350 360 0.154 0.156 0.169 0.147 0.168 0.3 0.3 0.3 0.3 0.3 150 800 1200 mV 120 190 250 ps ps NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 20. Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 W to VCC − 2.0 V. http://onsemi.com 6 800 8 700 7 600 6 500 5 400 4 300 3 200 2 ÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉ 100 0 0 1000 2000 1 (JITTER) 3000 4000 5000 JITTER OUT ps (RMS) VOUTpp (mV) MC10EP17, MC100EP17 ÉÉ ÉÉ 6000 FREQUENCY (MHz) Figure 2. Fmax/Jitter Q Zo = 50 W D Receiver Device Driver Device Q D Zo = 50 W 50 W 50 W VTT VTT = VCC − 2.0 V Figure 3. Typical Termination for Output Driver and Device Evaluation (See Application Note AND8020/D − Termination of ECL Logic Devices.) http://onsemi.com 7 MC10EP17, MC100EP17 ORDERING INFORMATION Package Shipping † MC10EP17DT TSSOP−20 75 Units / Rail MC10EP17DTG TSSOP−20 (Pb−Free) 75 Units / Rail MC10EP17DTR2 TSSOP−20 2500 / Tape & Reel MC10EP17DTR2G TSSOP−20 (Pb−Free) 2500 / Tape & Reel MC10EP17DW SOIC−20 38 Units / Rail MC10EP17DWG SOIC−20 (Pb−Free) 38 Units / Rail MC10EP17DWR2 SOIC−20 1000 / Tape & Reel MC10EP17DWR2G SOIC−20 (Pb−Free) 1000 / Tape & Reel MC10EP17MNG QFN−20 (Pb−Free) 92 Units / Rail MC10EP17MNTXG QFN−20 (Pb−Free) 3000 / Tape & Reel MC100EP17DT TSSOP−20 75 Units / Rail MC100EP17DTG TSSOP−20 (Pb−Free) 75 Units / Rail MC100EP17DTR2 TSSOP−20 2500 / Tape & Reel MC100EP17DTR2G TSSOP−20 (Pb−Free) 2500 / Tape & Reel MC100EP17DW SOIC−20 38 Units / Rail MC100EP17DWG SOIC−20 (Pb−Free) 38 Units / Rail MC100EP17DWR2 SOIC−20 1000 / Tape & Reel MC100EP17DWR2G SOIC−20 (Pb−Free) 1000 / Tape & Reel MC100EP17MNG QFN−20 (Pb−Free) 92 Units / Rail MC100EP17MNTXG QFN−20 (Pb−Free) 3000 / Tape & Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Resource Reference of Application Notes AN1405/D − ECL Clock Distribution Techniques AN1406/D − Designing with PECL (ECL at +5.0 V) AN1503/D − ECLinPSt I/O SPiCE Modeling Kit AN1504/D − Metastability and the ECLinPS Family AN1568/D − Interfacing Between LVDS and ECL AN1672/D − The ECL Translator Guide AND8001/D − Odd Number Counters Design AND8002/D − Marking and Date Codes AND8020/D − Termination of ECL Logic Devices AND8066/D − Interfacing with ECLinPS AND8090/D − AC Characteristics of ECL Devices http://onsemi.com 8 MC10EP17, MC100EP17 PACKAGE DIMENSIONS TSSOP−20 CASE 948E−02 ISSUE C 20X 0.15 (0.006) T U 2X L K REF 0.10 (0.004) S L/2 20 M T U S V K K1 ÍÍÍÍ ÍÍÍÍ ÍÍÍÍ S J J1 11 B −U− PIN 1 IDENT SECTION N−N 0.25 (0.010) N 1 10 M 0.15 (0.006) T U S A −V− NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE −W−. N F DETAIL E −W− C G D H DETAIL E 0.100 (0.004) −T− SEATING DIM A B C D F G H J J1 K K1 L M PLANE SOLDERING FOOTPRINT* 7.06 1 0.65 PITCH 16X 0.36 16X 1.26 DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 9 MILLIMETERS MIN MAX 6.40 6.60 4.30 4.50 −−− 1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.27 0.37 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.252 0.260 0.169 0.177 −−− 0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.011 0.015 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ MC10EP17, MC100EP17 PACKAGE DIMENSIONS SO−20 WB CASE 751D−05 ISSUE G A 20 q X 45 _ E h 1 10 20X B B 0.25 M T A S B S A L H M 10X 0.25 NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS OF B DIMENSION AT MAXIMUM MATERIAL CONDITION. 11 B M D 18X e A1 SEATING PLANE C T http://onsemi.com 10 DIM A A1 B C D E e H h L q MILLIMETERS MIN MAX 2.35 2.65 0.10 0.25 0.35 0.49 0.23 0.32 12.65 12.95 7.40 7.60 1.27 BSC 10.05 10.55 0.25 0.75 0.50 0.90 0_ 7_ MC10EP17, MC100EP17 PACKAGE DIMENSIONS QFN−20 CASE 485E−01 ISSUE O NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION D APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 MM FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. −X− A M −Y− N B 0.25 (0.010) T 0.25 (0.010) T R J C 0.08 (0.003) T −T− K SEATING PLANE E H DIM A B C D E F G H J K L M N P R MILLIMETERS MIN MAX 4.00 BSC 4.00 BSC 0.80 1.00 0.23 0.35 2.75 2.85 2.75 2.85 0.50 BSC 1.38 1.43 0.20 REF 0.00 0.05 0.35 0.45 2.00 BSC 2.00 BSC 1.38 1.43 0.60 0.80 INCHES MIN MAX 0.157 BSC 0.157 BSC 0.031 0.039 0.009 0.014 0.108 0.112 0.108 0.112 0.020 BSC 0.054 0.056 0.008 REF 0.000 0.002 0.014 0.018 0.079 BSC 0.079 BSC 0.054 0.056 0.024 0.031 G L 6 10 5 11 1 15 F 20 D 16 NOTE 3 0.10 (0.004) M P T X Y ECLinPS is a trademark of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 11 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC10EP17/D