ICS84329B Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER GENERAL DESCRIPTION FEATURES The ICS84329B is a general purpose, single output high frequency synthesizer and a HiPerClockS™ member of the HiPerClockS™ family of High Performance Clock Solutions from ICS. The VCO operates at a frequency range of 250MHz to 700MHz. The VCO frequency is programmed in steps equal to the value of the crystal frequency divided by 16. The VCO and output frequency can be programmed using the serial or parallel interfaces to the configuration logic. The output can be configured to divide the VCO frequency by 1, 2, 4, and 8. Output frequency steps as small as 125kHz to 1MHz can be achieved using a 16MHz crystal depending on the output dividers. • Fully integrated PLL, no external loop filter requirements ICS • One differential 3.3V LVPECL output • Parallel resonant crystal oscillator interface • Output frequency range: 31.25MHz to 700MHz • VCO range: 250MHz to 700MHz • Parallel interface for programming counter and output dividers during power-up • Serial 3 wire interface • RMS Period jitter: 5.5ps (maximum) • Cycle-to-cycle jitter: 35ps (maximuml) • 3.3V supply voltage • 0°C to 70°C ambient operating temperature • Available in both standard and lead-free RoHS compliant packages VEE TEST VCC VEE XTAL_IN OSC XTAL_OUT S_CLOCK 26 18 N1 S_DATA 27 17 N0 S_LOAD 28 16 M8 28-Lead PLCC 1 15 V Package 2 14 11.6mm x 11.4mm x 4.1mm 3 13 Top View M7 12 M4 VCCA ÷ 16 nc nc XTAL_IN PLL M6 M5 M3 VEE TEST VCC VCC VEE S_CLOCK 1 32 31 30 29 28 27 26 25 24 nc S_DATA 2 23 N1 S_LOAD 3 22 N0 VCCA 4 VCCA 5 nc 6 nc 7 18 M5 XTAL_IN 8 17 9 10 11 12 13 14 15 16 M4 ICS84329B 32-Lead LQFP 21 Y package 20 7mm x 7mm x 1.4mm 19 Top View M8 M7 M6 nc M3 M2 M1 M0 nP_LOAD OE XTAL_OUT www.icst.com/products/hiperclocks.html 1 M2 9 10 11 nFOUT N0:N1 8 FOUT TEST M0:M8 7 VCC CONFIGURATION INTERFACE LOGIC 6 M1 0 5 M0 ÷M FOUT nFOUT nP_LOAD VCO 4 OE 1 ÷1 ÷2 ÷4 ÷8 ICS84329B XTAL_OUT PHASE DETECTOR 84329BV FOUT VCC 25 24 23 22 21 20 19 OE S_LOAD S_DATA S_CLOCK nP_LOAD nFOUT PIN ASSIGNMENT BLOCK DIAGRAM REV. B JANUARY 18, 2006 ICS84329B Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER FUNCTIONAL DESCRIPTION NOTE: The functional description that follows describes operation using a 16MHz crystal. Valid PLL loop divider values for different crystal or input frequencies are defined in the Input Frequency Characteristics, Table 6, NOTE 1. N output divider. On the LOW-to-HIGH transition of the nP_LOAD input, the data is latched and the M divider remains loaded until the next LOW transition on nP_LOAD or until a serial event occurs. The TEST output is Mode 000 (shift register out) when operating in the parallel input mode. The relationship between the VCO frequency, the crystal frequency fxtal and the M divider is defined as follows: fVCO = 16 x M The ICS84329B features a fully integrated PLL and therefore requires no external components for setting the loop bandwidth. A series-resonant, fundamental crystal is used as the input to the on-chip oscillator. The output of the oscillator is divided by 16 prior to the phase detector. With a 16MHz crystal this provides a 1MHz reference frequency. The VCO of the PLL operates over a range of 250MHz to 700MHz. The output of the M divider is also applied to the phase detector. The M value and the required values of M0 through M8 are shown in Table 3B, Programmable VCO Frequency Function Table. Valid M values for which the PLL will achieve lock are defined as 250 ≤ M ≤ 511. The frequency out is defined as follows: fout fVCO fxtal M x = = N N 16 The phase detector and the M divider force the VCO output frequency to be M times the reference frequency by adjusting the VCO control voltage. Note that for some values of M (either too high or too low), the PLL will not achieve lock. The output of the VCO is scaled by a divider prior to being sent to each of the LVPECL output buffers. The divider provides a 50% output duty cycle. Serial operation occurs when nP_LOAD is HIGH and S_LOAD is LOW. The shift register is loaded by sampling the S_DATA bits with the rising edge of S_CLOCK. The contents of the shift register are loaded into the M divider when S_LOAD transitions from LOW-to-HIGH. The M divide and N output divide The programmable features of the ICS84329B support two values are latched on the HIGH-to-LOW transition of S_LOAD. input modes to program the M divider and N output divider. If S_LOAD is held HIGH, data at the S_DATA input is passed The two input operational modes are parallel and serial. Fig- directly to the M divider on each rising edge of S_CLOCK. ure 1 shows the timing diagram for each mode. In parallel mode The serial mode can be used to program the M and N bits and the nP_LOAD input is LOW. The data on inputs M0 through test bits T2:T0. The internal registers T2:T0 determine the state M8 and N0 through N1 is passed directly to the M divider and of the TEST output as follows: T2 T1 T0 TEST Output fOUT 0 0 0 Shift Register Out fOUT 0 0 1 High fOUT 0 1 0 PLL Reference Xtal ÷ 16 fOUT 0 1 1 VCO ÷ M fOUT (non 50% Duty M divider) 1 0 0 fOUT fOUT LVCMOS Output Frequency < 200MHz 1 0 1 Low fOUT 1 1 0 S_CLOCK ÷ M S_CLOCK ÷ N divider (non 50% Duty Cycle M divider) 1 1 1 fOUT ÷ 4 fOUT SERIAL LOADING S_CLOCK T2 S_DATA t S_LOAD S T1 T0 N1 N0 M8 M7 M6 M5 M4 M3 M2 M1 M0 t H nP_LOAD t S PARALLEL LOADING M0:M8, N0:N1 M, N nP_LOAD t S t H S_LOAD Time FIGURE 1. PARALLEL & SERIAL LOAD OPERATIONS 84329BV www.icst.com/products/hiperclocks.html 2 REV. B JANUARY 18, 2006 ICS84329B Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER TABLE 1. PIN DESCRIPTIONS Name Type Description VCCA XTAL_IN, XTAL_OUT Power Analog supply pin. Input Cr ystal oscillator interface. XTAL_IN is the input. XTAL_OUT is the output. OE Input Pullup nP_LOAD Input Pullup M0, M1, M2, M3, M4, M5, M6, M7, M8 Input Pullup N0, N1 Input Pullup VEE Power TEST Output VCC Power nFOUT, FOUT Output S_CLOCK Input Pulldown S_DATA Input Pulldown S_LOAD Input Pulldown NOTE: Pullup and Pulldown refer to internal Output enable. When logic HIGH, the outputs are enabled (default). When logic LOW, the outputs are disabled and drive differential low: FOUT = LOW, nFOUT = HIGH. LVCMOS / LVTTL interface levels. Parallel load input. Determines when data present at M8:M0 is loaded into M divider, and when data present at N1:N0 sets the N output divide value. LVCMOS / LVTTL interface levels. M divider inputs. Data latched on LOW-to-HIGH transistion of nP_LOAD input. LVCMOS / LVTTL interface levels. Determines N output divider value as defined in Table 3C Function Table. LVCMOS / LVTTL interface levels. Negative supply pins. Test output which is used in the serial mode of operation. LVCMOS / LVTTL interface levels. Core supply pins. Differential output for the synthesizer. 3.3V LVPECL interface levels. Clocks the serial data present at S_DATA input into the shift register on the rising edge of S_CLOCK. LVCMOS / LVTTL interface levels. Shift register serial input. Data sampled on the rising edge of S_CLOCK. LVCMOS / LVTTL interface levels. Controls transition of data from shift register into the M divider. LVCMOS / LVTTL interface levels. input resistors. See Table 2, Pin Characteristics, for typical values. TABLE 2. PIN CHARACTERISTICS Symbol Parameter CIN Input Capacitance Test Conditions Minimum Typical 4 Maximum Units pF RPULLUP Input Pullup Resistor 51 kΩ RPULLDOWN Input Pulldown Resistor 51 kΩ 84329BV www.icst.com/products/hiperclocks.html 3 REV. B JANUARY 18, 2006 ICS84329B Integrated Circuit Systems, Inc. TABLE 3A. PARALLEL AND 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER SERIAL MODE FUNCTION TABLE Inputs nP_LOAD M N S_LOAD S_CLOCK S_DATA X X X X X X L Data Data X X X ↑ Data Data L X X H X X L ↑ Data H X X ↑ L Data H X X ↓ L Data H X X L NOTE: L = LOW H = HIGH X = Don't care ↑ = Rising edge transition ↓ = Falling edge transition X X Conditions Reset. M and N bits are all set HIGH. Data on M and N inputs passed directly to M divider and N output divider. TEST mode 000. Data is latched into input registers and remains loaded until next LOW transition or until a serial event occurs. Serial input mode. Shift register is loaded with data on S_DATA on each rising edge of S_CLOCK. Contents of the shift register are passed to the M divider and N output divider. M divide and N output divide values are latched. Parallel or serial input do not affect shift registers. TABLE 3B. PROGRAMMABLE VCO FREQUENCY FUNCTION TABLE 256 128 64 32 16 8 4 2 1 M8 M7 M6 M5 M4 M3 M2 M1 M0 0 1 0 0 1 1 1 0 0 1 1 0 1 • • • • VCO Frequency (MHz) M Divide 250 250 0 1 1 1 1 1 251 251 0 1 1 1 1 1 252 252 0 1 1 1 1 1 253 253 0 1 1 1 1 • • • • • • • • • • • • • • • • • • 509 509 1 1 1 1 1 1 1 0 1 510 510 1 1 1 1 1 1 1 1 0 511 511 1 1 1 1 1 1 1 1 1 NOTE 1: These M divide values and the resulting frequencies correspond to a crystal frequency of 16MHz. TABLE 3C. PROGRAMMABLE OUTPUT DIVIDER FUNCTION TABLE Inputs N1 N0 0 0 N Divider Value 1 Output Frequency (MHz) Minimum Maximum 250 700 0 1 2 125 35 0 1 0 4 62.5 175 1 1 8 31.25 87.5 84329BV www.icst.com/products/hiperclocks.html 4 REV. B JANUARY 18, 2006 ICS84329B Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER ABSOLUTE MAXIMUM RATINGS Supply Voltage, VCC 4.6V Inputs, VI -0.5V to VCC + 0.5V Outputs, IO Continuous Current Surge Current 50mA 100mA Package Thermal Impedance, θJA 37.8°C/W (0 lfpm) Storage Temperature, TSTG -65°C to 150°C NOTE: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only. Functional operation of product at these conditions or any conditions beyond those listed in the DC Characteristics or AC Characteristics is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability. TABLE 4A. POWER SUPPLY DC CHARACTERISTICS, VCC = VCCA = 3.3V±5%, TA = 0°C TO 70°C Symbol Parameter Test Conditions Minimum Typical Maximum Units VCC Core Supply Voltage 3.135 3.3 3.465 V VCCA Analog Supply Voltage 3.135 3.3 3.465 V ICC Power Supply Current 125 mA ICCA Analog Supply Current 15 mA Maximum Units TABLE 4B. LVCMOS / LVTTL DC CHARACTERISTICS, VCC = VCCA = 3.3V±5%, TA = 0°C TO 70°C Symbol Parameter Test Conditions Minimum Typical VIH Input High Voltage 2 VCC + 0.3 V VIL Input Low Voltage -0.3 0.8 V VCC = VIN = 3.465V 5 µA VCC = VIN = 3.465V 15 0 µA VOH M0-M8, N0, N1, OE, nP_LOAD Input High Current S_LOAD, S_DATA, S_CLOCK M0-M8, N0, N1, OE, nP_LOAD Input Low Current S_LOAD, S_DATA, S_CLOCK Output High Voltage; NOTE 1 VOL Output Low Voltage; NOTE 1 IIH IIL VCC = 3.465V, VIN = 0V -150 µA VCC = 3.465V, VIN = 0V -5 µA 2.6 V 0.5 V NOTE 1: Outputs terminated with 50Ω to VCC/2. See Parameter Measurement Information, 3.3V Output Load Test Circuit. TABLE 4C. LVPECL DC CHARACTERISTICS, VCC = VCCA = 3.3V±5%, TA = 0°C TO 70°C Symbol Parameter Test Conditions VOH Output High Voltage; NOTE 1 V OL Output Low Voltage; NOTE 1 VSWING Peak-to-Peak Output Voltage Swing Minimum Typical Maximum Units VCC - 1.4 VCC - 0.9 V VCC - 2.0 VCC - 1.7 V 0.6 1.0 V NOTE 1: Outputs terminated with 50Ω to VCC - 2V. 84329BV www.icst.com/products/hiperclocks.html 5 REV. B JANUARY 18, 2006 ICS84329B Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER TABLE 5. CRYSTAL CHARACTERISTICS Parameter Test Conditions Minimum Mode of Oscillation Typical Maximum Units Fundamental 25 MHz Equivalent Series Resistance (ESR) Frequency 10 50 Ω Shunt Capacitance 7 pF Drive Level 1 mW TABLE 6. INPUT FREQUENCY CHARACTERISTICS, VCC = VCCA = 3.3V±5%, TA = 0°C TO 70°C Symbol fIN Parameter Input Frequency Test Conditions XTAL; NOTE 1 Minimum Typical 10 Maximum Units 25 MHz S_CLOCK 50 MHz NOTE 1: For the cr ystal frequency range the M value must be set to achieve the minimum or maximum VCO frequency range of 250MHz or 700MHz. Using the minimum frequency of 10MHz valid values of M are 400 ≤ M ≤ 511. Using the maximum frequency of 25MHz valid values of M are 160 ≤ M ≤ 448. TABLE 7. AC CHARACTERISTICS, VCC = VCCA = 3.3V±5%, TA = 0°C TO 70°C Symbol Parameter FOUT Output Frequency Test Conditions t jit(per) Period Jitter, RMS; NOTE 1, 2 t jit(cc) Cycle-to-Cycle Jitter ; NOTE 1, 2 Minimum Typical Maximum Units 700 MHz fOUT ≥ 65MHz 5.5 ps fOUT < 65MHz 12 ps fOUT ≥ 50MHz 35 ps fOUT < 50MHz 50 ps 800 ps tR / tF Output Rise/Fall Time tS Setup Time 5 ns tH Hold Time 5 ns tL PLL Lock Time 20% to 80% 300 odc Output Duty Cycle See Parameter Measurement Information section. Characterized using a 16MHz XTAL. NOTE 1: This parameter is defined in accordance with JEDEC Standard 65 NOTE 2: See Applications section. 84329BV www.icst.com/products/hiperclocks.html 6 45 50 10 ms 55 % REV. B JANUARY 18, 2006 ICS84329B Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER PARAMETER MEASUREMENT INFORMATION 2V VCC , VCCA Qx SCOPE nFOUT FOUT tcycle n+1 ➤ LVPECL ➤ tcycle n ➤ ➤ nQx VEE t jit(cc) = tcycle n –tcycle n+1 1000 Cycles -1.3V ± 0.165V CYCLE-TO-CYCLE JITTER 3.3V OUTPUT LOAD AC TEST CIRCUIT nFOUT VOH FOUT VREF t PW t VOL 1σ contains 68.26% of all measurements 2σ contains 95.4% of all measurements 3σ contains 99.73% of all measurements 4σ contains 99.99366% of all measurements 6σ contains (100-1.973x10-7)% of all measurements odc = PERIOD t PW x 100% t PERIOD Histogram Reference Point Mean Period (Trigger Edge) (First edge after trigger) PERIOD JITTER OUTPUT DUTY CYCLE/PULSE WIDTH/PERIOD S_DATA S_CLOCK 80% t SET-UP 80% VSW I N G Clock Outputs S_LOAD 20% 20% tR t HOLD t SET-UP tF M0:M8 N0:N1 t HOLD nP_LOAD t SET-UP OUTPUT RISE/FALL TIME 84329BV SETUP AND HOLD www.icst.com/products/hiperclocks.html 7 REV. B JANUARY 18, 2006 ICS84329B Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER APPLICATION INFORMATION POWER SUPPLY FILTERING TECHNIQUES As in any high speed analog circuitry, the power supply pins are vulnerable to random noise. The ICS84329B provides separate power supplies to isolate any high switching noise from the outputs to the internal PLL. V CC and V CCA should be individually connected to the power supply plane through vias, and bypass capacitors should be used for each pin. To achieve optimum jitter performance, power supply isolation is required. Figure 2 illustrates how a 10Ω resistor along with a 10μF and a .01μF bypass capacitor should be connected to each VCCA pin. The 10Ω resistor can also be replaced by a ferrite bead. 3.3V VCC .01μF 10Ω .01μF 10μF VCCA FIGURE 2. POWER SUPPLY FILTERING CRYSTAL INPUT INTERFACE parallel resonant crystal and were chosen to minimize the ppm error. The optimum C1 and C2 values can be slightly adjusted for different board layouts. The ICS84329B has been characterized with 18pF parallel resonant crystals. The capacitor values, C1 and C2, shown in Figure 3 below were determined using a 25MHz, 18pF XTAL_IN C1 22p X1 18pF Parallel Cry stal XTAL_OUT C2 22p ICS84332 Figure 3. CRYSTAL INPUt INTERFACE RECOMMENDATIONS FOR UNUSED INPUT PINS INPUTS: LVCMOS CONTROL PINS: All control pins have internal pull-ups or pull-downs; additional resistance is not required but can be added for additional protection. A 1kΩ resistor can be used. 84329BV www.icst.com/products/hiperclocks.html 8 REV. B JANUARY 18, 2006 Integrated Circuit Systems, Inc. ICS84329B 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 14 12 Time (pS) 10 8 6 4 2 0 25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 425 450 475 500 525 Output Frequency (MHz) FIGURE 4A. RMS JITTER VS. fOUT (using a 16MHz XTAL) 60 50 Time (pS) 40 30 20 10 0 25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 425 450 475 500 525 Output Frequency (MHz) FIGURE 4B. CYCLE-TO-CYCLE JITTER 84329BV VS. fOUT (using a 16MHz XTAL) www.icst.com/products/hiperclocks.html 9 REV. B JANUARY 18, 2006 ICS84329B Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER LAYOUT GUIDELINE layout in the actual system will depend on the selected component types, the density of the components, the density of the traces, and the stack up of the P.C. board. M3 M2 M1 M0 nPLOAD OE The schematic of the ICS84329B layout example used in this layout guideline is shown in Figure 5A. The ICS84329B recommended PCB board layout for this example is shown in Figure 5B. This layout example is used as a general guideline. The C3 22p 16MHz,18pF 11 10 9 8 7 6 5 VCC M4 M5 M6 M7 M8 N2 N1 M [8 :0]= 11 00 1 00 0 0 (40 0 ) N[1 :0 ] =01 (Di vid e by 2) 12 13 14 15 16 17 18 M4 M5 M6 M7 M8 N0 N1 XTALIN nc nc VCCA S_LOAD S_DATA S_CLOCK 19 20 21 22 23 24 25 U1 M3 M2 M1 M0 nP_LOAD OE XTALOUT S P = S p ace (i .e. n ot i ntstal l e d) VCC 84329BV VCC X1 C4 22p 4 3 2 1 28 27 26 R7 10 VCCA C11 0.01u VEE TEST VCC VEE nFOUT FOUT VCC V CC=3 .3V C16 10u C1 0.1uF Zo = 50 Ohm Fou t = 2 00 M Hz RU10 1K RU11 SP RU12 1K C2 0.1u Zo = 50 Ohm OE nPLoad N0 RU9 SP N1 RU8 1K M8 RU7 1K M7 RU1 SP M1 M0 RU0 SP R2 50 RD0 1K RD1 1K RD7 SP RD8 SP RD9 1K RD10 SP RD6 1K R1 50 RD12 SP R3 50 FIGURE 5A. SCHEMATIC OF RECOMMENDED LAYOUT FOR 28 LEAD PLCC 84329BV www.icst.com/products/hiperclocks.html 10 REV. B JANUARY 18, 2006 ICS84329B Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER The following component footprints are used in this layout example: • The differential 50Ω output traces should have the same length. All the resistors and capacitors are size 0603. • Avoid sharp angles on the clock trace. Sharp angle turns cause the characteristic impedance to change on the transmission lines. POWER AND GROUNDING Place the decoupling capacitors C1, C2 and C3, as close as possible to the power pins. If space allows, placement of the decoupling capacitor on the component side is preferred. This can reduce unwanted inductance between the decoupling capacitor and the power pin caused by the via. • Keep the clock traces on the same layer. Whenever possible, avoid placing vias on the clock traces. Placement of vias on the traces can affect the trace characteristic impedance and hence degrade signal integrity. Maximize the power and ground pad sizes and number of vias capacitors. This can reduce the inductance between the power and ground planes and the component power and ground pins. • To prevent cross talk, avoid routing other signal traces in parallel with the clock traces. If running parallel traces is unavoidable, allow a separation of at least three trace widths between the differential clock trace and the other signal trace. The RC filter consisting of R7, C11, and C16 should be placed as close to the VCCA pin as possible. • Make sure no other signal traces are routed between the clock trace pair. CLOCK TRACES • The matching termination resistors should be located as close to the receiver input pins as possible. AND TERMINATION Poor signal integrity can degrade the system performance or cause system failure. In synchronous high-speed digital systems, the clock signal is less tolerant to poor signal integrity than other signals. Any ringing on the rising or falling edge or excessive ring back can cause system failure. The shape of the trace and the trace delay might be restricted by the available space on the board and the component location. While routing the traces, the clock signal traces should be routed first and should be locked prior to routing other signal traces. CRYSTAL The crystal X1 should be located as close as possible to the pins 4 (XTAL_IN) and 5 (XTAL_OUT). The trace length between the X1 and U1 should be kept to a minimum to avoid unwanted parasitic inductance and capacitance. Other signal traces should not be routed near the crystal traces. X1 C3 C4 U1 GND VCC PIN 2 C11 C16 VCCA PIN 1 VCCA R7 VIA Signals Traces C1 C2 50 Ohm Traces FIGURE 5B. PCB BOARD LAYOUT FOR ICS84329B 28 LEAD PLCC 84329BV www.icst.com/products/hiperclocks.html 11 REV. B JANUARY 18, 2006 ICS84329B Integrated Circuit Systems, Inc. TERMINATION FOR 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER LVPECL OUTPUTS The clock layout topology shown below is a typical termination for LVPECL outputs. The two different layouts mentioned are recommended only as guidelines. designed to drive 50Ω transmission lines. Matched impedance techniques should be used to maximize operating frequency and minmize signal distortion. Figures 6A and 6B show two different layouts which are recommended only as guidelines.Other suitable clock layouts may exist and it would be recommended that the board designers simulate to guarantee compatibility across all printed circuit and clock component process variations. FOUT and nFOUT are low impedance follower outputs that generate ECL/LVPECL compatible outputs. Therefore, terminating resistors (DC current path to ground) or current sources must be used for functionality. These outputs are 3.3V Zo = 50Ω 125Ω FOUT 125Ω FIN Zo = 50Ω Zo = 50Ω FOUT 50Ω 1 RTT = Z ((VOH + VOL) / (VCC – 2)) – 2 o Zo = 50Ω VCC - 2V RTT 84Ω FIGURE 6A. LVPECL OUTPUT TERMINATION 84329BV FIN 50Ω 84Ω FIGURE 6B. LVPECL OUTPUT TERMINATION www.icst.com/products/hiperclocks.html 12 REV. B JANUARY 18, 2006 ICS84329B Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER POWER CONSIDERATIONS This section provides information on power dissipation and junction temperature for the ICS84329B. Equations and example calculations are also provided. 1. Power Dissipation. The total power dissipation for the ICS84329B is the sum of the core power plus the power dissipated in the load(s). The following is the power dissipation for VCC = 3.3V + 5% = 3.465V, which gives worst case results. NOTE: Please refer to Section 3 for details on calculating power dissipated in the load. • • Power (core)MAX = VCC_MAX * IEE_MAX = 3.465V * 140mA = 485mW Power (outputs)MAX = 30mW/Loaded Output pair Total Power_MAX (3.465V, with all outputs switching) = 485mW + 30mW = 515mW 2. Junction Temperature. Junction temperature, Tj, is the temperature at the junction of the bond wire and bond pad and directly affects the reliability of the device. The maximum recommended junction temperature for HiPerClockSTM devices is 125°C. The equation for Tj is as follows: Tj = θJA * Pd_total + TA Tj = Junction Temperature θJA = Junction-to-Ambient Thermal Resistance Pd_total = Total Device Power Dissipation (example calculation is in section 1 above) TA = Ambient Temperature In order to calculate junction temperature, the appropriate junction-to-ambient thermal resistance θJA must be used. Assuming a moderate air flow of 200 linear feet per minute and a multi-layer board, the appropriate value is 31.1°C/W per Table 8A below. Therefore, Tj for an ambient temperature of 70°C with all outputs switching is: 70°C + 0.515W * 31.1°C/W = 86°C. This is well below the limit of 125°C. This calculation is only an example. Tj will obviously vary depending on the number of loaded outputs, supply voltage, air flow, and the type of board (single layer or multi-layer). TABLE 8A. THERMAL RESISTANCE θJA FOR 28-PIN PLCC, FORCED CONVECTION θJA by Velocity (Linear Feet per Minute) Multi-Layer PCB, JEDEC Standard Test Boards 0 200 500 37.8°C/W 31.1°C/W 28.3°C/W NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs. TABLE 8B. THERMAL RESISTANCE θJA FOR 32-PIN LQFP, FORCED CONVECTION θJA by Velocity (Linear Feet per Minute) 0 200 500 Single-Layer PCB, JEDEC Standard Test Boards 67.8°C/W 55.9°C/W 50.1°C/W Multi-Layer PCB, JEDEC Standard Test Boards 47.9°C/W 42.1°C/W 39.4°C/W NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs. 84329BV www.icst.com/products/hiperclocks.html 13 REV. B JANUARY 18, 2006 ICS84329B Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 3. Calculations and Equations. The purpose of this section is to derive the power dissipated into the load. LVPECL output driver circuit and termination are shown in the Figure 7. VCC Q1 VOUT RL 50 VCC - 2V FIGURE 7. LVPECL DRIVER CIRCUIT AND TERMINATION To calculate worst case power dissipation into the load, use the following equations which assume a 50Ω load, and a termination voltage of V - 2V. CC • For logic high, VOUT = V OH_MAX (V CC_MAX • -V OH_MAX OL_MAX CC_MAX CC_MAX – 0.9V ) = 0.9V For logic low, VOUT = V (V =V =V CC_MAX – 1.7V ) = 1.7V -V OL_MAX Pd_H is power dissipation when the output drives high. Pd_L is the power dissipation when the output drives low. Pd_H = [(V OH_MAX – (V CC_MAX - 2V))/R ] * (V CC_MAX L -V OH_MAX ) = [(2V - (V CC_MAX -V OH_MAX ))/R ] * (V CC_MAX L -V OH_MAX )= [(2V - 0.9V)/50Ω] * 0.9V = 19.8mW Pd_L = [(V OL_MAX – (V CC_MAX - 2V))/R ] * (V L CC_MAX -V OL_MAX ) = [(2V - (V CC_MAX -V OL_MAX ))/R ] * (V L CC_MAX -V OL_MAX )= [(2V - 1.7V)/50Ω] * 1.7V = 10.2mW Total Power Dissipation per output pair = Pd_H + Pd_L = 30mW 84329BV www.icst.com/products/hiperclocks.html 14 REV. B JANUARY 18, 2006 ICS84329B Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER RELIABILITY INFORMATION TABLE 9A. θJAVS. AIR FLOW TABLE FOR 28 LEAD PLCC θJA by Velocity (Linear Feet per Minute) Multi-Layer PCB, JEDEC Standard Test Boards 0 200 500 37.8°C/W 31.1°C/W 28.3°C/W NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs. TABLE 9B. θJAVS. AIR FLOW TABLE FOR 32 LEAD LQFP θJA by Velocity (Linear Feet per Minute) Single-Layer PCB, JEDEC Standard Test Boards Multi-Layer PCB, JEDEC Standard Test Boards 0 200 500 67.8°C/W 47.9°C/W 55.9°C/W 42.1°C/W 50.1°C/W 39.4°C/W NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs. TRANSISTOR COUNT The transistor count for ICS84329B is: 4408 Pin compatible with the MC12429 84329BV www.icst.com/products/hiperclocks.html 15 REV. B JANUARY 18, 2006 ICS84329B Integrated Circuit Systems, Inc. PACKAGE OUTLINE - V SUFFIX FOR 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 28 LEAD PLCC TABLE 10A. PACKAGE DIMENSIONS JEDEC VARIATION ALL DIMENSIONS IN MILLIMETERS SYMBOL MINIMUM MAXIMUM 28 N A 4.19 4.57 A1 2.29 3.05 A2 1.57 2.11 b 0.33 0.53 c 0.19 0.32 D 12.32 12.57 D1 11.43 11.58 D2 4.85 5.56 E 12.32 12.57 E1 11.43 11.58 E2 4.85 5.56 Reference Document: JEDEC Publication 95, MS-018 84329BV www.icst.com/products/hiperclocks.html 16 REV. B JANUARY 18, 2006 ICS84329B Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER PACKAGE OUTLINE - Y SUFFIX 32 LEAD LQFP TABLE 10B. PACKAGE DIMENSIONS JEDEC VARIATION ALL DIMENSIONS IN MILLIMETERS BBA SYMBOL MINIMUM NOMINAL MAXIMUM 32 N A -- -- 1.60 A1 0.05 -- 0.15 A2 1.35 1.40 1.45 b 0.30 0.37 0.45 c 0.09 -- 0.20 D 9.00 BASIC D1 7.00 BASIC D2 5.60 Ref. E 9.00 BASIC E1 7.00 BASIC E2 5.60 Ref. 0.80 BASIC e 0.60 0.75 L 0.45 θ 0° -- 7° ccc -- -- 0.10 Reference Document: JEDEC Publication 95, MS-026 84329BV www.icst.com/products/hiperclocks.html 17 REV. B JANUARY 18, 2006 ICS84329B Integrated Circuit Systems, Inc. 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER TABLE 11. ORDERING INFORMATION Part/Order Number Marking Package Shipping Packaging Temperature ICS84329BV ICS84329BV 28 Lead PLCC Tube 0°C to 70°C ICS84329BVT ICS84329BV 28 Lead PLCC 500 Tape & Reel 0°C to 70°C ICS84329BVLF ICS84329BVLF 28 Lead "Lead-Free" PLCC Tube 0°C to 70°C ICS84329BVLFT ICS84329BVLF 28 Lead "Lead-Free" PLCC 500 Tape & Reel 0°C to 70°C ICS84329BY ICS84329BY 32 Lead LQFP Tray 0°C to 70°C ICS84329BYT ICS84329BY 32 Lead LQFP 1000 Tape & Reel 0°C to 70°C ICS84329BYLF ICS84329BYLF 32 Lead "Lead-Free" LQFP Tray 0°C to 70°C ICS84329BYLFT ICS84329BYLF 32 Lead "Lead-Free" LQFP 1000 Tape & Reel 0°C to 70°C NOTE: Par ts thar are ordered with an "LF" suffix to the par t number are the Pb-Free configuration and are RoHS compliant. The aforementioned trademark, HiPerClockS™ is a trademark of Integrated Circuit Systems, Inc. or its subsidiaries in the United States and/or other countries. While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Incorporated (ICS) assumes no responsibility for either its use or for infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. 84329BV www.icst.com/products/hiperclocks.html 18 REV. B JANUARY 18, 2006 Integrated Circuit Systems, Inc. ICS84329B 700MHZ, LOW JITTER, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER REVISION HISTORY SHEET Rev Table A Page 1 1 B T5 T11 B T11 84329BV 2 6 17 8 8 18 Description of Change Features Section - added "Parallel resonant" to crystal bullet. Features Section - corrected Output frequency range from 25MHz to 31.25MHz. Added Lead-Free bullet. Updated Parallel & Serial Load Operations. Crystal Table - added Drive Level. Ordering Information Table - added Lead-Free par t numbers and note. Power Supply Filtering Techniques - added ferrite bead sentence. Added Recommendations for Unused Input and Output Pins. Ordering Information Table - added Lead-Free marking. www.icst.com/products/hiperclocks.html 19 Date 12/15/04 6/10/05 1/18/06 REV. B JANUARY 18, 2006