BYV32-50 THRU BYV32-200 FAST EFFICIENT PLASTIC RECTIFIER Reverse Voltage - 50 to 150 Volts Forward Current - 18.0 Amperes FEATURES TO-220AB 0.185 (4.70) 0.415 (10.54) MAX. 0.175 (4.44) 0.370 (9.40) 0.360 (9.14) 0.154 (3.91) 0.055 (1.39) DIA. 0.148 (3.74) 0.045 (1.14) 0.113 (2.87) 0.103 (2.62) 0.145 (3.68) 0.135 (3.43) 0.560 (14.22) 0.530 (13.46) 0.410 (10.41) 0.390 (9.91) 0.635 (16.13) 0.625 (15.87) 1 PIN 2 0.350 (8.89) 0.330 (8.38) 1.148 (29.16) 3 1.118 (28.40) 0.110 (2.79) 0.100 (2.54) 0.160 (4.06) 0.140 (3.56) 0.560 (14.22) 0.530 (13.46) ♦ Dual rectifier construction, positive centertap ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Glass passivated chip junctions ♦ Low power loss ♦ Low forward voltage, high current capability ♦ High surge capability ♦ Superfast recovery time for high efficiency ♦ High temperature soldering guaranteed: 250°C, 0.16" (4.06mm) from case for 10 seconds MECHANICAL DATA 0.105 (2.67) 0.095 (2.41) 0.037 (0.94) 0.027 (0.68) 0.105 (2.67) 0.095 (2.41) Case: JEDEC TO-220AB molded plastic body over passivated chips Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Weight: 0.08 ounce, 2.24 grams 0.022 (0.56) 0.014 (0.35) 0.205 (5.20) 0.195 (4.95) PIN 1 PIN 2 PIN 3 CASE Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS BYV32-50 BYV32-100 BYV32-150 BYV32-200 UNITS Maximum repetitive peak reverse voltage VRRM 50 100 150 200 Volts Maximum RMS voltage VRMS 35 70 105 140 Volts VDC 50 100 150 200 Volts Maximum DC blocking voltage Maximum average forward rectified current at TC=120°C I(AV) 18.0 Amps Peak forward surge current 10ms single half sine-wave superimposed at at TJ=150°C IFSM 150.0 Amps VF 1.15 0.85 Volts IR 10.0 600.0 µA Maximum reverse recovery time per leg (NOTE 1) trr 25.0 ns Typical junction capacitance per leg (NOTE 2) CJ 45.0 pF Maximum thermal resistance per leg (NOTE 3) RΘJA RΘJC 20.0 3.0 °C/W TJ, TSTG -65 to +150 °C Maximum instantaneous forward voltage per leg at: IF=20A IF=5.0A, TJ=100°C Maximum DC reverse current at rated DC blocking voltage TC=25°C TC=100°C Operating and storage temperature range NOTES: (1) Reverse recovery test conditions: IF=1A VR=30V, di/dt=100A/µs, Irr=10% IRM (2) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient and from junction to case per leg mounted on heatsink 4/98 RATINGS AND CHARACTERISTIC CURVES BYV32-50 THRU BYV32-200 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 20 RESISTIVE OR INDUCTIVE LOAD 18 16 12 8.0 4.0 0 0 50 100 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD CURRENT, AMPERES FIG.1 - FORWARD CURRENT DERATING CURVE 150 125 100 75 50 25 0 150 CASE TEMPERATURE, °C TJ=150°C 10ms SINGLE HALF SINE WAVE (JEDEC Method) 1 1,000 TJ = 25°C PULSE WIDTH = 300µs 1% DUTY CYCLE 10 1 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES 100 100 TC=100°C 10 1 INSTANTANEOUS FORWARD VOLTAGE, VOLTS TC=25°C 0.1 FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG 60 JUNCTION CAPACITANCE, pF 100 FIG. 4 - TYPICAL REVERSE CHARACTERISTICS PER LEG FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG INSTANTANEOUS FORWARD CURRENT, AMPERES 10 NUMBER OF CYCLES AT 50 HZ TJ=25°C f=1.0 MHZ Vsig=5mVp-p 50 40 30 20 10 0 1 10 REVERSE VOLTAGE, VOLTS 100 0 20 40 60 80 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 100