规格书编号 SPEC NO : HDBF07000E64SP01 产品 规 格书 SPECIFICATION CUSTOMER 客 户： PRODUCT 产 品： MODEL NO 型 号： SAW FILTER HDBF07000E64 SF6-4 PREPARED 编 制： CHECKED 审 核： APPROVED 批 准： D A T E 日 期： 2008-12-5 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 6 SAW FILTER HDBF07000E64 SF6-4 更改内容描述 Modify Content 备注 Remark 更改历史记录 History Record 更改日期 Date 2008.12.05 www.shoulder.cn 规格书编号 Spec. No. 产品型号 Part No. 客户产品型号 Customer No. SP01 Tel:0755-82916880 Fax:0755-82916881 修 改 了 Electronic Characteristics 中 的 相关内容 E-mail:[email protected] Page 2 of 6 SAW FILTER HDBF07000E64 SF6-4 1. SCOPE This specification shall cover the characteristics of SAW filter BF07000E64 2. ELECTRICAL SPECIFICATION DC Voltage VDC AC Voltage Vpp Operation temperature Storage temperature RF Power Dissipation 10V 10V 50Hz/60Hz -40℃ to +85℃ -40℃ to +85℃ 0dBm Electronic Characteristics Minimum Typical Center Frequency 中心频率 MHz Insertion Loss 插入损耗 dB BW3dB 3dB 带宽 70.0 - - 4.0 30.0 KHz 80 140 - Amplitude ripple in passband 带内波动 dB - Absolute Delay 时延 us - - 20 35 55 65 75 25 55 60 70 80 Attenuation 带外抑制 （偏离-6dB 点的频率） +/-50KHz +/-75KHz +/-125KHz +/-250KHz ≥+/-500KHz Input/output Impedance 阻抗 www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 dB - Maximum Ω E-mail:[email protected] ±0.4 9.6 - 50 Page 3 of 6 SAW FILTER HDBF07000E64 SF6-4 3. DIMENSION 4. TEST CIRCUIT * Actual matching values may vary due to PCB layout and parasitic 5. ENVIRONMENTAL CHARACTERISTICS www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 6 SAW FILTER HDBF07000E64 SF6-4 5-1 High temperature exposure Subject the device to +85℃ for 16 hours. Then release the filter into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in table 1. 5-2 Low temperature exposure Subject the device to -20℃ for 16 hours. Then release the device into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in table 1. 5-3 Temperature cycling Subject the device to a low temperature of -40℃for 30 minutes. Following by a high temperature of +80℃ for 30 Minutes. Then release the device into the room conditions for 24 hours prior to the measurement. It shall meet the specifications in table 1. 5-4 Resistance to solder heat Dip the device terminals no closer than 1.5mm into the solder bath at 260℃ ±10℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. The device shall meet the specifications in table 1. 5-5 Solderability Subject the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the terminals must be covered with new solder. It shall meet the specifications in table 1. 5-6 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1m 3 times. the device shall fulfill the specifications in table 1. 5-7 Vibration Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 Hz. The device shall fulfill the specifications in table 1. 5-8 Lead fatigue 5-8-1 Pulling test Weight along with the direction of lead without an shock 1kg. The device shall satisfy all the initial Characteristics. 5-8-2 Bending test Lead shall be subject to withstand against 90℃ bending with 450g weight in the direction of thickness. This operation shall be done toward both direction. The device shall show no evidence of damage and shall satisfy all the initial electrical characteristics. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 6 SAW FILTER HDBF07000E64 SF6-4 6. Typical frequency response 7. REMARK 6.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 6.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 6.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 6 of 6