Maxim MAX6346-T 5-pin up supervisory circuits with watchdog and manual reset Datasheet

MAX6316–MAX6322
5-Pin µP Supervisory Circuits with
Watchdog and Manual Reset
________________General Description
____________________________Features
The MAX6316–MAX6322 family of microprocessor (µP)
supervisory circuits monitors power supplies and
microprocessor activity in digital systems. It offers several combinations of push/pull, open-drain, and bidirectional (such as Motorola 68HC11) reset outputs, along
with watchdog and manual reset features. The Selector
Guide below lists the specific functions available from
each device. These devices are specifically designed
to ignore fast negative transients on VCC. Resets are
guaranteed valid for VCC down to 1V.
These devices are available in 26 factory-trimmed reset
threshold voltages (from 2.5V to 5V, in 100mV increments), featuring four minimum power-on reset timeout
periods (from 1ms to 1.12s), and four watchdog timeout
periods (from 6.3ms to 25.6s). Thirteen standard versions are available with an order increment requirement
of 2500 pieces (see Standard Versions table); contact
the factory for availability of other versions, which have
an order increment requirement of 10,000 pieces.
The MAX6316–MAX6322 are offered in a miniature
5-pin SOT23 package.
o Small 5-Pin SOT23 Package
o Available in 26 Reset Threshold Voltages
2.5V to 5V, in 100mV Increments
o Four Reset Timeout Periods
1ms, 20ms, 140ms, or 1.12s (min)
o Four Watchdog Timeout Periods
6.3ms, 102ms, 1.6s, or 25.6s (typ)
o Four Reset Output Stages
Active-High, Push/Pull
Active-Low, Push/Pull
Active-Low, Open-Drain
Active-Low, Bidirectional
o Guaranteed Reset Valid to VCC = 1V
o Immune to Short Negative VCC Transients
o Low Cost
o No External Components
________________________Applications
Portable Computers
Computers
Controllers
Intelligent Instruments
Portable/Battery-Powered Equipment
Embedded Control Systems
_______________Ordering Information
PART
MAX6316LUK_ _ _ _ - T
TEMP RANGE
PIN-PACKAGE
-40°C to +125°C
5 SOT23
MAX6316LUK_ _ _ _ / V + T -40°C to +125°C
5 SOT23
MAX6316MUK_ _ _ _ - T
-40°C to +125°C
5 SOT23
MAX6317HUK_ _ _ _ - T
-40°C to +125°C
5 SOT23
MAX6318HUK_ _ _ _ - T
-40°C to +125°C
5 SOT23
MAX6318MHUK_ _ _ _ - T
-40°C to +125°C
5 SOT23
Devices are available in both leaded and lead(Pb)-free packaging.
Specify lead-free by replacing “-T” with “+T” when ordering.
/V Denotes an automotive-qualified part.
Ordering Information continued at end of data sheet.
Typical Operating Circuit and Pin Configurations appear at
end of data sheet.
___________________________________________________________________Selector Guide
WATCHDOG
INPUT
MANUAL
RESET
INPUT
MAX6316L
MAX6316M
MAX6317H
MAX6318LH
PART
RESET OUTPUTS*
ACTIVE-LOW
PUSH/PULL
ACTIVE-HIGH
PUSH/PULL
ACTIVE-LOW
BIDIRECTIONAL
ACTIVE-LOW
OPEN-DRAIN
—
—
—
—
—
—
—
—
—
—
—
—
MAX6318MH
—
—
—
MAX6319LH
—
—
—
MAX6319MH
—
—
—
MAX6320P
—
—
—
MAX6321HP
—
—
—
MAX6322HP
—
—
—
*The MAX6318/MAX6319/MAX6321/MAX6322 feature two types of reset output on each device.
For pricing, delivery, and ordering information, please contact Maxim Direct
at 1-888-629-4642, or visit Maxim’s website at www.maximintegrated.com.
19-0496; Rev 11; 2/13
MAX6316–MAX6322
5-Pin µP Supervisory Circuits with
Watchdog and Manual Reset
ABSOLUTE MAXIMUM RATINGS
Voltage (with respect to GND)
VCC......................................................................-0.3V to +6V
RESET (MAX6320/MAX6321/MAX6322 only)...... -0.3V to +6V
All Other Pins.........................................-0.3V to (VCC + 0.3V)
Input/Output Current, All Pins .............................................20mA
Continuous Power Dissipation (TA = +70°C)
SOT23 (derate 7.1mW/°C above +70°C)...............571mW
Operating Temperature Range..........................-40°C to +125°C
Junction Temperature ......................................................+150°C
Storage Temperature Range..............................-65°C to +160°C
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow)
Leaded Package .........................................................+240°C
Lead-Free Package .....................................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VCC = 2.5V to 5.5V, TA = -40°C to +125°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
Operating Voltage Range
SYMBOL
VCC
CONDITIONS
MAX6316/MAX6317/MAX
6318/MAX6320/MAX6321
Supply Current
ICC
Reset Threshold
Temperature Coefficient
∆VTH/°C
Reset Threshold (Note 2)
VRST
MIN
TA = -40°C to +125°C
MAX6319/MAX6322:
MR unconnected
TYP
1.0
MAX
UNITS
5.5
V
VCC = 5.5V
10
20
VCC = 3.6V
5
12
VCC = 5.5V
3
12
VCC = 3.6V
3
8
µA
40
ppm/°C
TA = +25°C
VTH - 1.5%
VTH
VTH + 1.5%
TA = -40°C to +125°C
VTH - 2.5%
VTH
VTH + 2.5%
MAX63_ _ A_-T
1
1.4
2
MAX63_ _ B_-T
20
28
40
MAX63_ _ C_-T
140
200
280
MAX63_ _ D_-T
1120
1600
2240
Reset Threshold Hysteresis
3
Reset Active Timeout Period
tRP
VCC to RESET Delay
tRD
VCC falling at 1mV/µs
V
mV
ms
40
µs
PUSH/PULL RESET OUTPUT (MAX6316L/MAX6317H/MAX6318_H/MAX6319_H/MAX6321HP/MAX6322HP)
VOL
RESET Output Voltage
VOH
RESET Rise Time (MAX6316L,
MAX6318LH, MAX6319LH)
tR
VOL
RESET Output Voltage
VOH
VCC ≥ 1.0V, ISINK = 50µA
0.3
VCC ≥ 1.2V, ISINK = 100µA
0.3
VCC ≥ 2.7V, ISINK = 1.2mA
0.3
VCC ≥ 4.5V, ISINK = 3.2mA
0.4
VCC ≥ 2.7V, ISOURCE = 500µA
0.8 x VCC
VCC ≥ 4.5V, ISOURCE = 800µA
VCC - 1.5
Rise time is measured from 10% to 90%
of VCC; CL = 5pF, VCC = 3.3V (Note 3)
5
VCC ≥ 2.7V, ISINK = 1.2mA
V
25
ns
0.3
VCC ≥ 4.5V, ISINK = 3.2mA
0.4
VCC ≥ 1.8V, ISOURCE = 150µA
0.8 x VCC
VCC ≥ 2.7V, ISOURCE = 500µA
0.8 x VCC
VCC ≥ 4.5V, ISOURCE = 800µA
VCC - 1.5
V
Note 1: Overtemperature limits are guaranteed by design, not production tested.
Note 2: A factory-trimmed voltage divider programs the nominal reset threshold (VTH). Factory-trimmed reset thresholds are
available in 100mV increments from 2.5V to 5V (see Table 1 at end of data sheet).
Note 3: Guaranteed by design.
2
Maxim Integrated
MAX6316–MAX6322
5-Pin µP Supervisory Circuits with
Watchdog and Manual Reset
ELECTRICAL CHARACTERISTICS (continued)
(VCC = 2.5V to 5.5V, TA = -40°C to +125°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
BIDIRECTIONAL RESET OUTPUT (MAX6316M/MAX6318MH/MAX6319MH)
Transitional Flip-Flop Setup Time
RESET Output Rise Time
(Note 5)
tS
tR
(Note 4)
400
333
333
VCC = 3.0V, CL = 250pF
666
VCC = 5.0V, CL = 400pF
Active Pullup Enable Threshold
RESET Active Pullup Current
VPTH
VCC = 5.0V
ns
666
0.4
0.65
TA = -40°C to +85°C
4.2
4.7
5.2
TA = -40°C to +125°C
3.6
4.7
5.8
VCC = 5.0V
RESET Pullup Resistance
ns
VCC = 3.0V, CL = 120pF
VCC = 5.0V, CL = 200pF
V
20
mA
kΩ
OPEN-DRAIN RESET OUTPUT (MAX6320P/MAX6321HP/MAX6322HP)
RESET Output Voltage
Open-Drain Reset Output
Leakage Current
VOL
VCC > 1.0V, ISINK = 50µA
0.3
VCC > 1.2V, ISINK = 100µA
0.3
VCC > 2.7V, ISINK = 1.2mA
0.3
VCC > 4.5V, ISINK = 3.2mA
0.4
ILKG
1.0
V
µA
WATCHDOG INPUT (MAX6316/MAX6317H/MAX6318_H/MAX6320P/MAX6321HP)
Watchdog Timeout Period
WDI Pulse Width
WDI Input Threshold
WDI Input Current
(Note 7)
tWD
tWDI
VIL
VIH
IWDI
MAX63_ _ _W-T
4.3
6.3
9.3
MAX63_ _ _X-T
71
102
153
MAX63_ _ _Y-T
MAX63_ _ _Z-T
1.12
17.9
1.6
25.6
2.4
38.4
VIL = 0.3 x VCC, VIH = 0.7 x VCC
(Note 6)
50
VWDI = 0V, time average
0.7 x VCC
120
-20
s
ns
0.3 x VCC
WDI = VCC, time average
ms
160
-15
V
µA
MANUAL RESET INPUT (MAX6316_/MAX6317H/MAX6319_H/MAX6320P/MAX6322HP)
VIL
MR Input Threshold
VIH
VIL
VIH
MR Input Pulse Width
VTH > 4.0V
VTH < 4.0V
0.8
2.0
0.3 x VCC
0.7 x VCC
TA = -40°C to +85°C
1
TA = -40°C to +125°C
1.5
MR Glitch Rejection
MR to Reset Delay
Note 4:
Note 5:
Note 6:
Note 7:
µs
100
MR Pullup Resistance
35
VCC = 5V
V
52
230
ns
75
kΩ
ns
This is the minimum time RESET must be held low by an external pulldown source to set the active pullup flip-flop.
Measured from RESET VOL to (0.8 x VCC), RLOAD = ∞.
WDI is internally serviced within the watchdog period if WDI is left unconnected.
The WDI input current is specified as the average input current when the WDI input is driven high or low. The WDI input is
designed for a three-stated-output device with a 10µA maximum leakage current and capable of driving a maximum capacitive load of 200pF. The three-state device must be able to source and sink at least 200µA when active.
Maxim Integrated
3
MAX6316–MAX6322
5-Pin µP Supervisory Circuits with
Watchdog and Manual Reset
7
6
5
VCC = 3V
4
3
2
VCC = 1V
1
80
70
60
50
40
30
-40
-20
0
20
40
60
80
240
220
200
10
160
140
-20
0
20
40
60
80
-40
100
-20
20
0
40
60
80
100
TEMPERATURE (°C)
TEMPERATURE (°C)
MAX6316/MAX6317/MAX6318/MAX6320/MAX6321
NORMALIZED WATCHDOG TIMEOUT
PERIOD vs. TEMPERATURE
MAX6316toc04
1.05
1.04
1.03
1.02
1.01
1.00
0.99
0.98
0.97
0.96
0.95
NORMALIZED WATCHDOG TIMEOUT PERIOD
NORMALIZED RESET TIMEOUT
PERIOD vs. TEMPERATURE
NORMALIZED RESET TIMEOUT PERIOD
260
180
TEMPERATURE (°C)
1.05
1.04
1.03
1.02
1.01
1.00
0.99
0.98
0.97
0.96
0.95
-40
-20
0
20
40
60
80
100
-40
-20
0
20
40
60
80
TEMPERATURE (°C)
TEMPERATURE (°C)
MAXIMUM VCC TRANSIENT DURATION
vs. RESET THRESHOLD OVERDRIVE
MAX6316M/6318MH/6319MH
BIDIRECTIONAL
PULLUP CHARACTERISTICS
100
MAX6316toc07
MAX6316toc06
80
RESET OCCURS ABOVE LINES
70
TRANSIENT DURATION (µs)
280
20
-40
100
VCC = 5V
300
0
0
MAX6316toc03
90
MAX6316toc05
SUPPLY CURRENT (µA)
8
VCC FALLING AT 1mV/µs
VRST - VCC = 100mV
PROPAGATION DELAY (ns)
VCC = 5V
320
MAX6316toc02
9
100
RESET PROPAGATION DELAY (µs)
MAX6316toc01
10
MAX6316/MAX6317/MAX6319/MAX6320/MAX6322
MANUAL RESET TO RESET
PROPAGATION DELAY vs. TEMPERATURE
VCC FALLING TO RESET PROPAGATION
DELAY vs. TEMPERATURE
MAX6316/MAX6317/MAX6318/MAX6320/MAX6321
SUPPLY CURRENT vs. TEMPERATURE
VRST = 3.3V
60
+5V
74HC05
INPUT
PASSIVE
4.7kΩ
PULLUP
2V/div
4.7kΩ
100pF
VRST = 4.63V
50
+5V
40
VRST = 2.63V
INPUT
30
74HC05
100pF
20
VCC
RESET
MR GND
10
RESET, ACTIVE
PULLUP
2V/div
RESET
INPUT
5V/div
0
10
100
1000
200ns/div
RESET THRESHOLD OVERDRIVE (mV) VRST - VCC
4
Maxim Integrated
MAX6316–MAX6322
5-Pin µP Supervisory Circuits with
Watchdog and Manual Reset
______________________________________________________________Pin Description
PIN
MAX6316L
MAX6316M
MAX6320P
MAX6317H
MAX6318LH
MAX6318MH
MAX6321HP
MAX6319LH
MAX6319MH
MAX6322HP
NAME
FUNCTION
MAX6316L/MAX6318LH/MAX6319LH:
Active-Low, Reset Output. CMOS push/pull
output (sources and sinks current).
1
—
1
1
RESET
MAX6316M/MAX6318MH/MAX6319MH:
Bidirectional, Active-Low, Reset Output.
Intended to interface directly to microprocessors
with bidirectional resets such as the Motorola
68HC11.
MAX6320P/MAX6321HP/MAX6322HP:
Open-Drain, Active-Low, Reset Output. NMOS output (sinks current only). Connect a pullup resistor
from RESET to any supply voltage up to 6V.
—
1
3
3
RESET
2
2
2
2
GND
3
4
5
Maxim Integrated
3
4
5
—
4
5
4
—
5
Active-High, Reset Output. CMOS push/pull output
(sources and sinks current). Inverse of RESET.
Ground
MR
Active-Low, Manual Reset Input. Pull low to force a
reset. Reset remains asserted for the duration of
the Reset Timeout Period after MR transitions from
low to high. Leave unconnected or connected to
VCC if not used.
WDI
Watchdog Input. Triggers a reset if it remains
either high or low for the duration of the watchdog
timeout period. The internal watchdog timer clears
whenever a reset asserts or whenever WDI sees a
rising or falling edge. To disable the watchdog feature, leave WDI unconnected or three-state the driver connected to WDI.
VCC
Supply Voltage. Reset is asserted when VCC
drops below the Reset Threshold Voltage (VRST).
Reset remains asserted until VCC rises above
VRST and for the duration of the Reset Timeout
Period (tRP) once VCC rises above VRST.
5
MAX6316–MAX6322
5-Pin µP Supervisory Circuits with
Watchdog and Manual Reset
VCC
MAX6316–MAX6322
RESET
(ALL EXCEPT MAX6317)
RESET
GENERATOR
RESET
(ALL EXCEPT
MAX6316/MAX6320P)
VCC
1.23V
52kΩ
MR
(ALL EXCEPT
MAX6318/MAX6321)
WATCHDOG
TRANSITION
DETECTOR
WDI
(ALL EXCEPT
MAX6319/MAX6322)
WATCHDOG
TIMER
52kΩ
GND
Figure 1. Functional Diagram
_______________Detailed Description
A microprocessor’s (µP) reset input starts or restarts the
µP in a known state. The reset output of the MAX6316–
MAX6322 µP supervisory circuits interfaces with the
reset input of the µP, preventing code-execution errors
during power-up, power-down, and brownout conditions (see the Typical Operating Circuit). The MAX6316/
MAX6317/MAX6318/MAX6320/MAX6321 are also capable of asserting a reset should the µP become stuck in
an infinite loop.
the watchdog timeout period (tWD). Reset remains asserted for the specified reset active timeout period (tRP) after
VCC rises above the reset threshold, after MR transitions
low to high, or after the watchdog timer asserts the reset
(MAX6316_/MAX6317H/MAX6318_H/MAX6320P/
MAX6321HP). After the reset active timeout period (tRP)
expires, the reset output deasserts, and the watchdog
timer restarts from zero (Figure 2).
VCC
Reset Output
The MAX6316L/MAX6318LH/MAX6319LH feature an
active-low reset output, while the MAX6317H/
MAX6318_H/MAX6319_H/MAX6321HP/MAX6322HP
feature an active-high reset output. RESET is guaranteed to be a logic low and RESET is guaranteed to be a
logic high for VCC down to 1V.
The MAX6316–MAX6322 assert reset when VCC is below
the reset threshold (V RST ), when MR is pulled low
(MAX6316_/MAX6317H/MAX6319_H/MAX6320P/
MAX6322HP only), or if the WDI pin is not serviced within
6
1V
VRST
VRST
1V
GND
RESET
tRP
tRD
RESET
tRP
tRD
GND
Figure 2. Reset Timing Diagram
Maxim Integrated
MAX6316–MAX6322
5-Pin µP Supervisory Circuits with
Watchdog and Manual Reset
Bidirectional RESET Output
The MAX6316M/MAX6318MH/MAX6319MH are designed
to interface with µPs that have bidirectional reset pins,
such as the Motorola 68HC11. Like an open-drain output,
these devices allow the µP or other devices to pull the
bidirectional reset (RESET) low and assert a reset condition. However, unlike a standard open-drain output, it
includes the commonly specified 4.7kΩ pullup resistor
with a P-channel active pullup in parallel.
This configuration allows the MAX6316M/MAX6318MH/
MAX6319MH to solve a problem associated with µPs
that have bidirectional reset pins in systems where several devices connect to RESET (Figure 3). These µPs
can often determine if a reset was asserted by an external device (i.e., the supervisor IC) or by the µP itself
(due to a watchdog fault, clock error, or other source),
and then jump to a vector appropriate for the source of
the reset. However, if the µP does assert reset, it does
not retain the information, but must determine the
cause after the reset has occurred.
The following procedure describes how this is done in
the Motorola 68HC11. In all cases of reset, the µP pulls
RESET low for about four external-clock cycles. It then
releases RESET, waits for two external-clock cycles,
then checks RESET’s state. If RESET is still low, the µP
concludes that the source of the reset was external
and, when RESET eventually reaches the high state, it
jumps to the normal reset vector. In this case, storedstate information is erased and processing begins from
scratch. If, on the other hand, RESET is high after a
delay of two external-clock cycles, the processor
knows that it caused the reset itself and can jump to a
different vector and use stored-state information to
determine what caused the reset.
A problem occurs with faster µPs; two external-clock
cycles are only 500ns at 4MHz. When there are several
devices on the reset line, and only a passive pullup resistor is used, the input capacitance and stray capacitance
can prevent RESET from reaching the logic high state (0.8
VCC) in the time allowed. If this happens, all resets will
be interpreted as external. The µP output stage is guaranteed to sink 1.6mA, so the rise time can not be reduced
considerably by decreasing the 4.7kΩ internal pullup
resistance. See Bidirectional Pullup Characteristics in the
Typical Operating Characteristics.
The MAX6316M/MAX6318MH/MAX6319MH overcome
this problem with an active pullup FET in parallel with the
4.7kΩ resistor (Figures 4 and 5). The pullup transistor
holds RESET high until the µP reset I/O or the supervisory
circuit itself forces the line low. Once RESET goes below
VPTH, a comparator sets the transition edge flip-flop, indicating that the next transition for RESET will be low to
high. When RESET is released, the 4.7kΩ resistor pulls
RESET up toward VCC. Once RESET rises above VPTH
but is below (0.85 x VCC), the active P-channel pullup
turns on. Once RESET rises above (0.85 x VCC) or the
2µs one-shot times out, the active pullup turns off. The
parallel combination of the 4.7kΩ pullup and the
VCC
VCC
WDI*
MR**
68HC11
4.7kΩ
RESET
CIRCUITRY
RESET
RESET
RESET
CIRCUITRY
RESET***
CIN
MAX6316M
MAX6318MH
MAX6319MH
* MAX6316M/MAX6318MH
** MAX6316M/MAX6319MH
*** ACTIVE-HIGH PUSH/PULL MAX6318MH/MAX6319MH
CIN
CSTRAY
RESET
CIN
OTHER DEVICES
Figure 3. MAX6316M/MAX6318MH/MAX6319MH Supports Additional Devices on the Reset Bus
Maxim Integrated
7
MAX6316–MAX6322
5-Pin µP Supervisory Circuits with
Watchdog and Manual Reset
VCC
MAX6316M
MAX6318MH
MAX6319MH
LASERTRIMMED
RESISTORS
VCC
VREF
52kΩ
MR
RESET
GENERATOR
WATCHDOG ON
2µs ONE
SHOT
CIRCUITRY
WDI
(MAX6316M/
MAX6319MH)
(MAX6316M/
MAX6318MH)
VCC
2µs ONE SHOT
TRANSITION
FLIP-FLOP
R
Q
4.7kΩ
FF
S
RESET
ACTIVE PULLUP
ENABLE COMPARATOR
0.85VCC
0.65V
GND
Figure 4. MAX6316/MAX6318MH/MAX6319MH Bidirectional Reset Output Functional Diagram
8
Maxim Integrated
MAX6316–MAX6322
5-Pin µP Supervisory Circuits with
Watchdog and Manual Reset
P-channel transistor on-resistance quickly charges
stray capacitance on the reset line, allowing RESET to
transition from low to high within the required two electronic-clock cycles, even with several devices on the
reset line. This process occurs regardless of whether
the reset was caused by VCC dipping below the reset
threshold, the watchdog timing out, MR being asserted,
or the µP or other device asserting RESET. The parts do
not require an external pullup. To minimize supply current consumption, the internal 4.7kΩ pullup resistor disconnects from the supply whenever the MAX6316M/
MAX6318MH/MAX6319MH assert reset.
Open-Drain RESET Output
The MAX6320P/MAX6321HP/MAX6322HP have an
active-low, open-drain reset output. This output structure will sink current when RESET is asserted. Connect
a pullup resistor from RESET to any supply voltage up
to 6V (Figure 6). Select a resistor value large enough to
VCC
tRP
OR
µC RESET DELAY
RESET
0.7V
0.8 x VCC
tR
tS
RESET PULLED LOW
BY µC OR
RESET GENERATOR
ACTIVE
PULLUP
TURNS ON
Figure 5. Bidirectional RESET Timing Diagram
+3.3V
VCC
10kΩ
WDI**
RESET
5V SYSTEM
RESET***
MAX6320
MAX6321
MAX6322
GND
* MAX6320/MAX6322
** MAX6320/MAX6321
*** MAX6321/MAX6322
Figure 6. MAX6320P/MAX6321HP/MAX6322HP Open-Drain
RESET Output Allows Use with Multiple Supplies
Maxim Integrated
Manual-Reset Input
The MAX6316_/MAX6317H/MAX6319_H/MAX6320P/
MAX6322HP feature a manual reset input. A logic low on
MR asserts a reset. After MR transitions low to high, reset
remains asserted for the duration of the reset timeout period (tRP). The MR input is connected to VCC through an
internal 52kΩ pullup resistor and therefore can be left
unconnected when not in use. MR can be driven with
TTL-logic levels in 5V systems, with CMOS-logic levels in
3V systems, or with open-drain or open-collector output
devices. A normally-open momentary switch from MR to
ground can also be used; it requires no external
debouncing circuitry. MR is designed to reject fast,
negative-going transients (typically 100ns pulses). A
0.1µF capacitor from MR to ground provides additional
noise immunity.
The MR input pin is equipped with internal ESD-protection
circuitry that may become forward biased. Should MR be
driven by voltages higher than VCC, excessive current
would be drawn, which would damage the part. For
example, assume that MR is driven by a +5V supply other
than VCC. If VCC drops lower than +4.7V, MR’s absolute
maximum rating is violated [-0.3V to (VCC + 0.3V)], and
undesirable current flows through the ESD structure from
MR to VCC. To avoid this, use the same supply for MR as
the supply monitored by VCC. This guarantees that the
voltage at MR will never exceed VCC.
Watchdog Input
+5.0V
MR*
register a logic low (see Electrical Characteristics), and
small enough to register a logic high while supplying all
input current and leakage paths connected to the RESET
line. A 10kΩ pullup is sufficient in most applications.
The MAX6316_/MAX6317H/MAX6318_H/MAX6320P/
MAX6321HP feature a watchdog circuit that monitors
the µP’s activity. If the µP does not toggle the watchdog
input (WDI) within the watchdog timeout period (tWD),
reset asserts. The internal watchdog timer is cleared by
reset or by a transition at WDI (which can detect pulses
as short as 50ns). The watchdog timer remains cleared
while reset is asserted. Once reset is released, the
timer begins counting again (Figure 7).
The WDI input is designed for a three-stated output
device with a 10µA maximum leakage current and the
capability of driving a maximum capacitive load of 200pF.
The three-state device must be able to source and sink at
least 200µA when active. Disable the watchdog function
by leaving WDI unconnected or by three-stating the driver
connected to WDI. When the watchdog timer is left open
circuited, the timer is cleared internally at intervals equal
to 7/8 of the watchdog period.
9
MAX6316–MAX6322
5-Pin µP Supervisory Circuits with
Watchdog and Manual Reset
VCC
tRST
RESET
tRP
tWD
VCC
MAX6316
MAX6318
MAX6319
tRP
VCC
WDI
GND
RESET
100kΩ
MAX6316/MAX6317
MAX6318/MAX6320
MAX6321
Figure 7. Watchdog Timing Relationship
Figure 8. Ensuring RESET Valid to VCC = 0V on Active-Low
Push/Pull and Bidirectional Outputs
Applications Information
MAX6317
MAX6318
MAX6319
MAX6321*
MAX6322*
Watchdog Input Current
The WDI input is internally driven through a buffer and
series resistor from the watchdog counter. For minimum
watchdog input current (minimum overall power consumption), leave WDI low for the majority of the watchdog timeout period. When high, WDI can draw as much
as 160µA. Pulsing WDI high at a low duty cycle will
reduce the effect of the large input current. When WDI
is left unconnected, the watchdog timer is serviced
within the watchdog timeout period by a low-high-low
pulse from the counter chain.
Negative-Going VCC Transients
These supervisors are immune to short-duration, negative-going VCC transients (glitches), which usually do
not require the entire system to shut down. Typically,
200ns large-amplitude pulses (from ground to VCC) on
the supply will not cause a reset. Lower amplitude pulses result in greater immunity. Typically, a VCC transient
that goes 100mV under the reset threshold and lasts
less than 4µs will not trigger a reset. An optional 0.1µF
bypass capacitor mounted close to VCC provides additional transient immunity.
Ensuring Valid Reset Outputs
Down to VCC = 0V
The MAX6316_/MAX6317H/MAX6318_H/MAX6319_H/
MAX6321HP/MAX6322HP are guaranteed to operate
properly down to VCC = 1V. In applications that require
valid reset levels down to VCC = 0V, a pulldown resistor
to active-low outputs (push/pull and bidirectional only,
Figure 8) and a pullup resistor to active-high outputs
(push/pull only, Figure 9) will ensure that the reset line
is valid while the reset output can no longer sink or
10
GND
VCC
100kΩ
VCC
RESET
*THIS SCHEMATIC DOES NOT WORK ON THE OPEN-DRAIN
OUTPUTS OF THE MAX6321/MAX6322.
Figure 9. Ensuring RESET Valid to VCC = 0V on Active-High
Push/Pull Outputs
source current. This scheme does not work with the
open-drain outputs of the MAX6320/MAX6321/MAX6322.
The resistor value used is not critical, but it must be
large enough not to load the reset output when VCC is
above the reset threshold. For most applications,
100kΩ is adequate.
Watchdog Software Considerations
(MAX6316/MAX6317/MAX6318/
MAX6320/MAX6321)
One way to help the watchdog timer monitor software
execution more closely is to set and reset the watchdog
input at different points in the program, rather than
pulsing the watchdog input high-low-high or low-highlow. This technique avoids a stuck loop, in which the
watchdog timer would continue to be reset inside the
loop, keeping the watchdog from timing out.
Maxim Integrated
MAX6316–MAX6322
5-Pin µP Supervisory Circuits with
Watchdog and Manual Reset
Figure 10 shows an example of a flow diagram where
the I/O driving the watchdog input is set high at the
beginning of the program, set low at the end of every
subroutine or loop, then set high again when the program returns to the beginning. If the program should
hang in any subroutine, the problem would be quickly
corrected, since the I/O is continually set low and the
watchdog timer is allowed to time out, causing a reset
or interrupt to be issued. As described in the Watchdog
Input Current section, this scheme results in higher time
average WDI current than does leaving WDI low for the
majority of the timeout period and periodically pulsing it
low-high-low.
START
SET WDI
HIGH
PROGRAM
CODE
POSSIBLE
INFINITE LOOP PATH
SUBROUTINE OR
PROGRAM LOOP
SET WDI LOW
RETURN
Figure 10. Watchdog Flow Diagram
__________________Pin Configurations
Typical Operating Circuit
TOP VIEW
RESET 1
GND 2
5 VCC
RESET 1
VIN
5 VCC
VCC
VCC
MAX6317
MAX6316
MAX6320
RESET
GND 2
RESET
MAX6316
MR 3
4 WDI
MR 3
RESET 1
GND 2
5 VCC
MAX6318
MAX6321
RESET 3
Maxim Integrated
RESET 1
GND 2
4 WDI
SOT23
MANUAL
RESET
SOT23
SOT23
µP
4 WDI
MR
GND
WDI
I/O
GND
5 VCC
MAX6319
MAX6322
RESET 3
4 MR
SOT23
11
MAX6316–MAX6322
5-Pin µP Supervisory Circuits with
Watchdog and Manual Reset
Table 1. Factory-Trimmed Reset Thresholds
PART
MIN
4.925
7.827
4.728
4.630
4.561
4.433
4.314
4.236
4.137
4.039
3.940
3.842
3.743
3.645
3.546
3.448
3.349
3.251
3.152
3.034
2.955
2.886
2.758
2.660
2.591
2.463
MAX63___50_ _-T
MAX63___49_ _-T
MAX63___48_ _-T
MAX63___47_ _-T
MAX63___46_ _-T
MAX63___45_ _-T
MAX63___44_ _-T
MAX63___43_ _-T
MAX63___42_ _-T
MAX63___41_ _-T
MAX63___40_ _-T
MAX63___39_ _-T
MAX63___38_ _-T
MAX63___37_ _-T
MAX63___36_ _-T
MAX63___35_ _-T
MAX63___34_ _-T
MAX63___33_ _-T
MAX63___32_ _-T
MAX63___31_ _-T
MAX63___30_ _-T
MAX63___29_ _-T
MAX63___28_ _-T
MAX63___27_ _-T
MAX63___26_ _-T
MAX63___25_ _-T
TA = +25°C
TYP
5.000
4.900
4.800
4.700
4.630
4.500
4.390
4.300
4.200
4.100
4.000
3.900
3.800
3.700
3.600
3.500
3.400
3.300
3.200
3.080
3.000
2.930
2.800
2.700
2.630
2.500
MAX
5.075
4.974
4.872
4.771
4.699
4.568
4.446
4.365
4.263
4.162
4.060
3.959
3.857
3.756
3.654
3.553
3.451
3.350
3.248
3.126
3.045
2.974
2.842
2.741
2.669
2.538
TA = -40°C to +125°C
MIN
MAX
4.875
5.125
4.778
5.023
4.680
4.920
4.583
4.818
4.514
4.746
4.388
4.613
4.270
4.490
4.193
4.408
4.095
4.305
3.998
4.203
3.900
4.100
3.803
3.998
3.705
3.895
3.608
3.793
3.510
3.690
3.413
3.588
3.315
3.485
3.218
3.383
3.120
3.280
3.003
3.157
2.925
3.075
2.857
3.000
2.730
2.870
2.633
2.768
2.564
2.696
2.438
2.563
Table 2. Standard Versions
RESET
THRESHOLD (V)
MINIMUM
RESET
TIMEOUT (ms)
TYPICAL
WATCHDOG
TIMEOUTS (s)
MAX6316LUK29CY-T
2.93
140
1.6
ACDE
MAX6316LUK46CY-T
4.63
140
1.6
ACDD
MAX6316MUK29CY-T
2.93
140
1.6
ACDG
PART
12
SOT
TOP
MARK
MAX6316MUK46CY-T
4.63
140
1.6
ACDF
MAX6317HUK46CY-T
4.63
140
1.6
ACDQ
MAX6318LHUK46CY-T
4.63
140
1.6
ACDH
MAX6318MHUK46CY-T
4.63
140
1.6
ACDJ
MAX6319LHUK46C-T
4.63
140
—
ACDK
MAX6319MHUK46C-T
4.63
140
—
ACDM
MAX6320PUK29CY-T
2.93
140
1.6
ACDO
Maxim Integrated
MAX6316–MAX6322
5-Pin µP Supervisory Circuits with
Watchdog and Manual Reset
Table 2. Standard Versions (continued)
MINIMUM
RESET
TIMEOUT (ms)
RESET
THRESHOLD (V)
PART
TYPICAL
WATCHDOG
TIMEOUTS (s)
SOT
TOP
MARK
ACDN
MAX6320PUK46CY-T
4.63
140
1.6
MAX6321HPUK46CY-T
4.63
140
1.6
ACGL
MAX6322HPUK46C-T
4.63
140
1.6
ACGN
Note: Thirteen standard versions are available, with a required order increment of 2500 pieces. Sample stock is generally held on standard versions only. The required order increment for nonstandard versions is 10,000 pieces. Contact factory for availability.
Table 3. Reset/Watchdog Timeout Periods
PART
RESET TIMEOUT PERIODS
SUFFIX
MIN
TYP
MAX
A
1
1.6
2
B
20
30
40
C
140
200
280
D
1.12
1.60
2.24
UNITS
ms
s
WATCHDOG TIMEOUT
W
4.3
6.3
9.3
X
71
102
153
Y
1.12
1.6
2.4
Z
17.9
25.6
38.4
__Ordering Information (continued)
ms
s
Chip Information
SUBSTRATE IS INTERNALLY CONNECTED TO V+
TEMP RANGE
PIN-PACKAGE
MAX6319LHUK_ _ _ - T
-40°C to +125°C
5 SOT23
MAX6319MHUK_ _ _ - T
-40°C to +125°C
5 SOT23
MAX6320PUK_ _ _ _ - T
-40°C to +125°C
5 SOT23
MAX6320PUK_ _ _ _ / V +T
-40°C to +125°C
5 SOT23
MAX6321HPUK_ _ _ - T
-40°C to +125°C
5 SOT23
MAX6322HPUK_ _ _ - T
-40°C to +125°C
5 SOT23
Devices are available in both leaded and lead-free packaging.
Specify lead-free by replacing “-T” with “+T” when ordering.
/V Denotes an automotive-qualified part.
Note: These devices are available with factory-set VCC reset
thresholds from 2.5V to 5V, in 0.1V increments. Insert the
desired nominal reset threshold (25 to 50, from Table 1) into the
blanks following the letters UK. All devices offer factory-programmed reset timeout periods. Insert the letter corresponding
to the desired reset timeout period (A, B, C, or D from Table 3)
into the blank following the reset threshold suffix. Parts that offer
a watchdog feature (see Selector Guide) are factory-trimmed to
one of four watchdog timeout periods. Insert the letter corresponding to the desired watchdog timeout period (W, X, Y, or Z
from Table 3) into the blank following the reset timeout suffix.
Package Information
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a
“+”, “#”, or “-” in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but the
drawing pertains to the package regardless of RoHS status.
Maxim Integrated
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
5 SOT23
U5+2
21-0057
90-0174
13
MAX6316–MAX6322
5-Pin µP Supervisory Circuits with
Watchdog and Manual Reset
Revision History
REVISION
NUMBER
REVISION
DATE
0
1/98
Initial release.
1
4/98
Update to show MAX6319 as an existing part.
1, 2, 12
2
7/98
Update specifications, Selector Guide, and Table 2.
1, 12, 14
3
1/99
Include extended temperature range in EC table globals, Table 1, Ordering
Information.
4
11/99
Update available products and versions in Table 2 and Ordering Information.
5
9/02
Addition of RESET rise time specification to Electrical Characteristics table.
6
12/05
Add lead-free option to Ordering Information.
7
11/07
Add automotive temperature to Ordering Information, Electrical Characteristics
table, Table 1, and updated Package Information.
8
8/09
Updated Ordering Information.
DESCRIPTION
PAGES
CHANGED
—
1, 2, 3, 12, 13, 14
1, 12, 14
1, 2
1, 13, 14
1, 2, 3, 12, 13, 14
13
9
6/10
Added automotive part and soldering temperatures.
10
10/11
Added automotive-qualified part ordering option for MAX6316 family
2, 13
1
11
2/13
Changed /V-T suffix to /V+T in Ordering Information
1
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent
licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and
max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
14 ________________________________Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000
© 2013 Maxim Integrated Products, Inc.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.