ON MT9J003D00STMUC2CBC1-200 1/2.3â inch 10 mp cmos digital image sensor Datasheet

MT9J003
MT9J003 1/2.3‐Inch 10 Mp
CMOS Digital Image Sensor
General Description
The ON Semiconductor MT9J003 is a 1/2.3-inch CMOS
active-pixel digital imaging sensor with an active pixel array of 3856
(H) x 2764 (V) including border pixels. It can support 10 megapixel
(3664 (H) x 2748 (V)) digital still images and a 1080 p (3840 (H) x
2160 (V)) digital video mode. It incorporates sophisticated on-chip
camera functions such as windowing, mirroring, column and row skip
modes, and snapshot mode. It is programmable through a simple
two-wire serial interface and has very low power consumption.
The MT9J003 digital image sensor features ON Semiconductor’s
breakthrough low-noise CMOS imaging technology that achieves
near-CCD image quality (based on signal-to-noise ratio and low-light
sensitivity) while maintaining the inherent size, cost, and integration
advantages of CMOS.
When operated in its default 4:3 still-mode, the sensor generates a
full resolution image at 15 frames per second (fps) using the HiSPi
serial interface. An on-chip analog-to-digital converter (ADC)
generates a 12-bit value for each pixel.
www.onsemi.com
ILCC48 10x10
CASE 847AK
ORDERING INFORMATION
See detailed ordering and shipping information on page 3 of
this data sheet.
Features
•
•
•
•
•
•
•
•
•
•
•
•
1080p Digital Video Mode
Simple Two-wire Serial Interface
Auto Black Level Calibration
Support for External Mechanical Shutter
Support for External LED or Xenon Flash
High Frame Rate Preview Mode with Arbitrary Down-size Scaling
from Maximum Resolution
Programmable Controls: Gain, Horizontal and Vertical Blanking,
Auto Black Level Offset Correction, Frame Size/rate, Exposure,
Left–right and Top–bottom Image Reversal, Window Size, and
Panning
Data Interfaces: Parallel or Four-lane Serial High-speed Pixel
Interface (HiSPi) Differential Signaling (Sub-LVDS)
On-die Phase-locked Loop (PLL) Oscillator
Bayer Pattern Downsize Scaler
Integrated Position-based Color and Lens Shading Correction
One-time Programmable Memory (OTPM) for Storing Module
Information
Applications
• Digital Video Cameras
• Digital Still Cameras
© Semiconductor Components Industries, LLC, 2009
February, 2017 − Rev. 5
1
Publication Order Number:
MT9J003/D
MT9J003
Table 1. KEY PARAMETERS
Parameter
Value
Optical Format
1/2.3-inch (4:3)
Active Imager Size
6.440 mm (H) x 4.616 mm (V), 7.923 mm Diagonal (Entire Sensor)
6.119 mm (H) x 4.589 mm (V), 7.649 mm Diagonal (Still Mode)
6.413 mm (H) x 3.607 mm (V), 7.358 mm Diagonal (Video Mode)
Active Pixels
3856 (H) x 2764 (V) (Entire Sensor)
3664 (H) x 2748 (V) (4:3, Still Mode)
3840 (H) x 2160 (V) (16:9, Video Mode)
Pixel Size
1.67 x 1.67 μm
Chief Ray Angle
0°, 13.4°
Color Filter Array
RGB Bayer Pattern
Shutter Type
Electronic Rolling Shutter (ERS) with Global Reset Release (GRR)
Maximum Data Rate
96 Mp/s
Maximum Master Clock
60 MHz
Input Clock Frequency
6–48 MHz
Maximum Data Rate
Frame Rate
Parallel
80 Mp/s at 80 MHz PIXCLK
HiSPi (4-lane)
2.8 Gbps
Still Mode, 4:3 (3664 (H) x 2748 (V)
Programmable up to 15 fps Serial I/F, 7.5 fps Parallel I/F
Preview Mode
VGA
30 fps with Binning
60 fps with Skip2bin2
1080p Mode
(1920 H x 1080 V)
60 fps Using HiSPi I/F
30 fps Using Parallel I/F
ADC Resolution
12-bit, On-die
Responsivity
0.31 V/lux-sec (550 nm)
Dynamic Range
65.2 dB
SNRMAX
Supply Voltage
Power Consumption
34 dB
I/O Digital
1.7–1.9 (V) (1.8 (V) Nominal)
or 2.4–3.1 (V) (2.8 (V) Nominal)
Digital
1.7–1.9 (V) (1.8 (V) Nominal)
Analog
2.4–3.1 (V) (2.8 (V) Nominal)
SLVS I/O
0.4−0.8 (V) (0.4 or 0.8 (V) Nominal)
Still Mode at 15 fps w/ Serial I/F
638 mW
Still Mode at 7.5 fps w/ Parallel I/F
388 mW
Preview
250 mW Low Power VGA
Standby
500 μW (Typical, EXTCLK Disabled)
Power Consumption
TBD
Package
48-pin iLCC (10 mm x 10 mm) Bare Die,
48pin Tiny PLCC (12 mm x 12 mm)
Operating Temperature
−30°C to +70°C (at Junction)
www.onsemi.com
2
MT9J003
ORDERING INFORMATION
Table 2. AVAILABLE PART NUMBERS
Product Description
Orderable Product Attribute Description †
10 MP 1” CIS
Die Sales, 200 μm Thickness
MT9J003I12STCU-DP
10 MP 1/2.3” CIS
Dry Pack with Protective Film
MT9J003I12STCU-DR
10 MP 1/2.3” CIS
Dry Pack without Protective Film
MT9J003I12STCV2-DP
10 MP 1/2.3” CIS
Dry Pack with Protective Film
MT9J003I12STCV2-TP
10 MP 1/2.3” CIS
Tape & Reel with Protective Film
MT9J003I12STMU-DP
10 MP 1/2.3” CIS
Dry Pack with Protective Film
Part Number
MT9J003D00STMUC2CBC1-200
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specification Brochure, BRD8011/D.
FUNCTIONAL OVERVIEW
The MT9J003 is a progressive-scan sensor that generates
a stream of pixel data at a constant frame rate. It uses an
on-chip, phase-locked loop (PLL) to generate all internal
clocks from a single master input clock running between
Active−Pixel
Sensor (APS)
Array
Analog Processing
6 and 48 MHz. The maximum output pixel rate is 80 Mp/s,
corresponding to a pixel clock rate of 80 MHz. A block
diagram of the sensor is shown in Figure 1.
Sync
Signals
Timing Control
ADC
Shading
Correction
Scaler
Control Registers
Limiter
FIFO
Data
Out
Two-wire
Serial
Interface
Figure 1. Block Diagram
setting. These registers can be accessed through a two-wire
serial interface.
The output from the sensor is a Bayer pattern; alternate
rows are a sequence of either green and red pixels or blue and
green pixels. The offset and gain stages of the analog signal
chain provide per-color control of the pixel data.
The control registers, timing and control, and digital
processing functions shown in Figure 1 are partitioned into
three logical parts:
• A sensor core that provides array control and data path
corrections. The output of the sensor core is a 12-bit
parallel pixel data stream qualified by an output data
clock (PIXCLK), together with LINE_VALID (LV) and
FRAME_VALID (FV) signals or a 4-lane serial
high-speed pixel interface (HiSPi).
• A digital shading correction block to compensate for
color/brightness shading introduced by the lens or chief
ray angle (CRA) curve mismatch.
The core of the sensor is a 10 Mp active-pixel array. The
timing and control circuitry sequences through the rows of
the array, resetting and then reading each row in turn. In the
time interval between resetting a row and reading that row,
the pixels in the row integrate incident light. The exposure
is controlled by varying the time interval between reset and
readout. Once a row has been read, the data from the
columns is sequenced through an analog signal chain
(providing offset correction and gain), and then through an
ADC. The output from the ADC is a 12-bit value for each
pixel in the array. The ADC output passes through a digital
processing signal chain (which provides further data path
corrections and applies digital gain).
The pixel array contains optically active and
light-shielded (“dark”) pixels. The dark pixels are used to
provide data for on-chip offset-correction algorithms
(“black level” control).
The sensor contains a set of control and status registers
that can be used to control many aspects of the sensor
behavior including the frame size, exposure, and gain
www.onsemi.com
3
MT9J003
• Additional functionality is provided. This includes a
exposure time. Additional I/O signals support the provision
of an external mechanical shutter.
horizontal and vertical image scaler, a limiter, a data
compressor, an output FIFO, and a serializer.
Pixel Array
The sensor core uses a Bayer color pattern, as shown in
Figure 2. The even-numbered rows contain green and red
pixels; odd-numbered rows contain blue and green pixels.
Even-numbered columns contain green and blue pixels;
odd-numbered columns contain red and green pixels.
The output FIFO is present to prevent data bursts by
keeping the data rate continuous. Programmable slew rates
are also available to reduce the effect of electromagnetic
interference from the output interface.
A flash output signal is provided to allow an external
xenon or LED light source to synchronize with the sensor
Column Readout Direction
..
.
Black Pixels
First Clear
Active Pixel
(100, 69)
Row
Readout
Direction
B G2 B G2 B
... G1 R G1 R G1
B G2 B G2 B
G1 R G1 R G1
Figure 2. Block Diagram
www.onsemi.com
4
MT9J003
OPERATING MODES
By default, the MT9J003 powers up with the serial pixel
data interface enabled. The sensor can operate in serial
HiSPi or parallel mode
For low-noise operation, the MT9J003 requires separate
power supplies for analog and digital power. Incoming
digital and analog ground conductors should be placed in
such a way that coupling between the two are minimized.
Both power supply rails should also be routed in such a way
that noise coupling between the two supplies and ground is
minimized.
CAUTION: ON Semiconductor does not recommend the
use of inductance filters on the power
supplies or output signals.
From
Controller
VDD_SLVS_TX
Master clock
(6–48 MHz)
HiSPi
Analog Analog
PHY I/O PLL
Power1 Power1 Power1 Power1
VDD_SLVS
VDD_IO VDD
1.5 kW2, 3
1.5 kW2
Digital
Digital I/0 Core
Power1
Power1
EXTCLK
VDD_PLL VAA VAA_PIX
SLVS_0P
SLVS_0N
SLVS_1P
SLVS_1N
SLVS_2P
SLVS_2N
SLVS_3P
SDATA
SCLK
GPI[3:0]4
SLVS_3N
SLVSC_P
SLVSC_N
RESET_BAR
SHUTTER
FLASH
TEST
GND_PLL DGND
VDD_IO
VDD
VDD_SLVS_TX VDD_PLL
VAA
1.
2.
3.
4.
5.
6.
7.
8.
9.
PIXGND
AGND
VAA_PIX
Digital
ground
Notes:
To
Controller
Analog
ground
All power supplies should be adequately decoupled.
ON Semiconductor recommends a resistor value of 1.5 kΩ, but it may be greater for slower two-wire speed.
This pull-up resistor is not required if the controller drives a valid logic level on SCLK at all times.
The GPI pins can be statically pulled HIGH or LOW to be used as module IDs, or they can be programmed to perform
special functions (TRIGGER, OE_N, SADDR, STANDBY) to be dynamically controlled.
VPP, which can be used during the module manufacturing process, is not shown in Figure 3. This pad is left unconnected
during normal operation.
The parallel interface output pads can be left unconnected if the serial output interface is used.
ON Semiconductor recommends that 0.1 μF and 10 μF decoupling capacitors for each power supply are mounted as
close as possible to the pad. Actual values and results may vary depending on layout and design considerations. Check
the MT9J003 demo headboard schematics for circuit recommendations
ON Semiconductor recommends that analog power planes are placed in a manner such that coupling with the digital
power planes is minimized.
The signal path between the HiSPi serial transmitter and receiver should be adequately designed to minimize any
trans-impedance mismatch and/or reflections on the data path.
Figure 3. Typical Configuration: Serial Four-Lane HiSPi Interface
www.onsemi.com
5
MT9J003
Master clock
(6–48 MHz)
PLL
Analog Analog
Power1 Power1 Power1
VDD_IO VDD VDD_TX0
1.5kΩ2, 3
1.5kΩ2
Digital
Digital I/0 Core
Power1 Power1
VDD_PLL VAA VAA_PIX
DOUT [11:0]
EXTCLK
PIXCLK
LINE_VALID
FRAME_VALID
SDATA
SCLK
SHUTTER
RESET_BAR
FLASH
GPI[3:0]4
TEST
VDD_IO
VDD
VDD_PLL
VAA
GND_PLL DGND
1.
2.
3.
4.
5.
6.
7.
8.
9.
PIX GND
AGND
VAA_PIX
Digital
ground
Notes:
To
controller
Analog
ground
All power supplies should be adequately decoupled.
ON Semiconductor recommends a resistor value of 1.5 kΩ, but it may be greater for slower two-wire speed.
This pull-up resistor is not required if the controller drives a valid logic level on SCLK at all times.
The GPI pins can be statically pulled HIGH or LOW to be used as module IDs, or they can be programmed to perform
special functions (TRIGGER, OE_N, SADDR, STANDBY) to be dynamically controlled.
VPP, which can be used during the module manufacturing process, is not shown in Figure 4. This pad is left unconnected
during normal operation.
The serial interface output pads can be left unconnected if the parallel output interface is used.
ON Semiconductor recommends that 0.1 μF and 10 μF decoupling capacitors for each power supply are mounted as
close as possible to the pad. Actual values and results may vary depending on layout and design considerations. Check
the MT9J003 demo headboard schematics for circuit recommendations.
ON Semiconductor recommends that analog power planes are placed in a manner such that coupling with the digital
power planes is minimized.
ON Semiconductor recommends that VDD_TX0 is tied to VDD when the sensor is using the parallel interface.
Figure 4. Typical Configuration: Parallel Pixel Data Interface
www.onsemi.com
6
MT9J003
SIGNAL DESCRIPTIONS
Table 3 provides signal descriptions for MT9J003 die. For
pad location and aperture information, refer to the MT9J003
die data sheet.
Table 3. SIGNAL DESCRIPTIONS
Pad Name
Pad Type
Description
EXTCLK
Input
Master Clock Input, 6–48 MHz
RESET_BAR
(XSHUTDOWN)
Input
Asynchronous active LOW reset. When asserted, data output stops and all internal registers
are restored to their factory default settings
SCLK
Input
Serial clock for access to control and status registers
GPI[3:0]
Input
General purpose inputs. After reset, these pads are powered-down by default;
this means that it is not necessary to bond to these pads. Any of these pads can be
configured to provide hardware control of the standby, output enable, SADDR select,
and shutter trigger functions.
Can be left floating if not used
TEST
Input
Enable manufacturing test modes. It should not be left floating. It can be tied to ground or
VDD_IO when used in parallel or HiSPi. It should be connected to DGND for normal operation
of the CCP2 configured sensor, or connected to VDD_IO power for the MIPI[-configured
sensor
SDATA
I/O
LINE_VALID
Output
LINE_VALID (LV) output. Qualified by PIXCLK
FRAME_VALID
Output
FRAME_VALID (FV) output. Qualified by PIXCLK
DOUT[11:0]
Output
Parallel pixel data output. Qualified by PIXCLK
PIXCLK
Output
Pixel clock. Used to qualify the LV, FV, and DOUT[11:0] outputs
FLASH
Output
Flash output. Synchronization pulse for external light source. Can be left floating if not used
SHUTTER
Output
Control for external mechanical shutter. Can be left floating if not used
VPP
Supply
Power supply used to program one-time programmable (OTP) memory. Disconnect pad
when not programming or when feature is not used
VDD_TX0
Supply
PHY power supply. Digital power supply for the MIPI or CCP2 serial data interface.
ON Semiconductor recommends that VDD_TX0 is always tied to VDD when using an
unpackaged sensor
VDD_SLVS
Supply
HiSPi power supply for data and clock output. This should be tied to VDD
VDD_SLVS_TX
Supply
Digital Power Supply for the HiSPi I/O
VAA
Supply
Analog Power Supply
VAA_PIX
Supply
Analog Power Supply for the Pixel Array
AGND
Supply
Analog Ground
Serial data from READs and WRITEs to control and status registers
VDD
Supply
Digital Power Supply
VDD_IO
Supply
I/O Power Supply
DGND
Supply
Common Ground for Digital and I/O
VDD_PLL
Supply
PLL Power Supply
GND_PLL
Supply
PLL Ground
PIXGND
Supply
Pixel Ground
SLVS_0P
Output
Lane 1 Differential HiSPi (LVDS) Serial Data (positive). Qualified by the SLVS Serial Clock
SLVS_0N
Output
Lane 1 Differential HiSPi (LVDS) Serial Data (negative). Qualified by the SLVS Serial Clock
SLVS_1P
Output
Lane 2 Differential HiSPi (LVDS) Serial Data (positive). Qualified by the SLVS Serial Clock
SLVS_1N
Output
Lane 2 Differential HiSPi (LVDS) Serial Data (negative). Qualified by the SLVS Serial Clock
SLVS_2P
Output
Lane 3 Differential HiSPi (LVDS) Serial Data (positive). Qualified by the SLVS Serial Clock
www.onsemi.com
7
MT9J003
Table 3. SIGNAL DESCRIPTIONS (continued)
SLVS_CP
Output
Differential HiSPi (LVDS) Serial Clock (positive). Qualified by the SLVS Serial Clock
SLVS_CN
Output
Differential HiSPi (LVDS) Serial Clock (positive). Qualified by the SLVS Serial Clock
GND
Lane 4 Differential HiSPi (LVDS) Serial Data (negative). Qualified by the SLVS Serial Clock
SLVS3_P
Output
SLVS3_N
SLVS_3N
SLVS2_P
Lane 4 Differential HiSPi (LVDS) Serial Data (positive). Qualified by the SLVS Serial Clock
SLVS2_N
Output
SLVSC_P
SLVS_3P
SLVSC_N
Lane 3 Differential HiSPi (LVDS) Serial Data (negative). Qualified by the SLVS Serial Clock
SLVS1_P
Output
SLVS1_N
SLVS_2N
SLVS0_P
Description
SLVS0_N
Pad Type
VDD_SLVS_TX
Pad Name
6
5
4
3
2
1
48
47
46
45
44
43
VDD_SLVS
7
42
AGND
VDD_IO
8
41
VAA
PIXGND
GND
13
36
VAA_PIX
VDD_IO
14
35
VAA_PIX
SDATA
15
34
NC
SCLK
16
33
NC
TEST
17
32
VAA
RESET_BAR
18
31
AGND
20
21
22
23
24
25
26
27
28
29
30
VPP
VDD
19
VDD_PLL
37
GND
12
FLASH
VDD
SHUTTER
VAA
GPI3
38
GPI2
NC
11
GPI1
VDD
EXTCLK
GPI0
NC
39
VDD_IO
40
GND
9
10
GND
Figure 5. HiSPi Package Pinout Diagram
www.onsemi.com
8
1
48
47
46
45
44
NC
DOUT2
2
GND
DOUT1
3
DOUT6
DOUT0
4
DOUT4
VDD_PLL
5
DOUT5
EXTCLK
6
DOUT3
GND
MT9J003
43
DOUT7
7
42
NC
DOUT8
8
41
PIXGND
VAA_PIX
PIXCLK
13
36
VAA
VDD
14
35
AGND
SCLK
15
34
VAA
SDATA
16
33
VPP
RESET_BAR
17
32
NC
VDD_IO
18
31
NC
19
20
21
22
23
24
25
26
27
28
29
30
GND
37
LINE_VALID
12
SHUTTER
VDD_IO
FRAME_VALID
VAA_PIX
FLASH
38
TEST
11
GND
DOUT11
GPI3
AGND
GPI2
DOUT10
GPI1
VAA
39
GPI0
40
VDD
9
10
DOUT9
Figure 6. 48−Pin iLCC Parallel Package Pinout Diagram
www.onsemi.com
9
MT9J003
OUTPUT DATA FORMAT
Serial Pixel Data Interface
standard video application where each line of active or
intra-frame blanking provided by the sensor is transmitted
at the same length. The packetized protocol will transmit
only the active data ignoring line-to-line and frame-to-frame
blanking data.
The HiSPi interface building block is a unidirectional
differential serial interface with four data and one double
data rate (DDR) clock lanes. One clock for every four serial
data lanes is provided for phase alignment across multiple
lanes. Figure 7 shows the configuration between the HiSPi
transmitter and the receiver.
The MT9J003 supports RAW8, RAW10, and RAW12
image data formats over a serial interface. The sensor
supports a 1 and 2-lane MIPI as well as the HiSPi interface.
These interfaces are not described in the data sheet.
High Speed Serial Pixel Interface
The High Speed Serial Pixel (HiSPi) interface uses four
data and one clock low voltage differential signaling
(LVDS) outputs.
• SLVS_CP, SLVS_CN
• SLVS_[0:3]P, SLVS_[0:3]N
The HiSPi interface supports two protocols, streaming
and packetized. The streaming protocol conforms to a
A camera containing
the HiSPi transmitter
Tx
PHY0
A host (DSP) containing
the HiSPi receiver
Dp0
Dp0
Dn0
Dn0
Dp1
Dp1
Dn1
Dn1
Dp2
Dp2
Dn2
Dn2
Dp3
Dp3
Dn3
Dn3
Cp0
Cp0
Cn0
Cn0
Rx
PHY0
Figure 7. HiSPi Transmitter and Receiver Interface Block Diagram
clock, the second on the following edge of clock. Figure 8
shows bit transmission. In this example, the word is
transmitted in order of MSB to LSB. The receiver latches
data at the rising and falling edge of the clock.
HiSPi Physical Layer
The HiSPi physical layer is partitioned into blocks of four
data lanes and an associated clock lane. Any reference to the
PHY in the remainder of this document is referring to this
minimum building block.
The PHY will serialize a 10-, 12-, 14- or 16-bit data word
and transmit each bit of data centered on a rising edge of the
TxPost
cp
…
cn
TxPre
dp
dn
…
MSB
1 UI
Figure 8. Timing Diagram
www.onsemi.com
10
LSB
MT9J003
DLL Timing Adjustment
data _lane 0
delay
del 2[2: 0]
delclock[2:0]
del 1[2: 0]
del 0[2: 0]
delay
delay
data _lane 1
clock_lane0
del 3[2: 0]
increase the setup or hold time at the receiver circuits and
can be used to compensate for skew introduced in PCB
design.
If the DLL timing adjustment is not required, the data and
clock lane delay settings should be set to a default code of
0x000 to reduce jitter, skew, and power dissipation.
The specification includes a DLL to compensate for
differences in group delay for each data lane. The DLL is
connected to the clock lane and each data lane, which acts as
a control master for the output delay buffers. Once the DLL
has gained phase lock, each lane can be delayed in 1/8 unit
interval (UI) steps. This additional delay allows the user to
delay
delay
data_lane2
data_lane3
Figure 9. Block Diagram of DLL Timing Adjustment
1 UI
dataN (de IN = 000)
cp (delclock = 000)
cp (delclock = 001)
cp (delclock = 010)
cp (delclock = 011)
cp (delclock = 100)
cp (delclock = 101)
cp (delclock = 110)
cp (delclock = 111)
increasing delclock_[2:0] increases clock delay
Figure 10. Delaying the clock_lane with Respect to data_lane
cp (delclock = 000)
dataN (delN = 000)
dataN (delN = 001)
dataN (delN = 010)
dataN (delN = 011)
dataN (delN = 100)
dataN (delN = 101)
dataN (delN = 110)
dataN (delN = 111)
increasing delN_[2:0] increases data delay
t
DLLSTEP
1 UI
Figure 11. Delaying data_lane with Respect to the clock_lane
www.onsemi.com
11
MT9J003
data. The streaming protocol will insert a SYNC code to
transmit each active data line and vertical blanking lines.
The packetized protocol will transmit a SYNC code to
note the start and end of each row. The packetized protocol
uses sync a “Start of Frame” (SOF) sync code at the start of
a frame and a “Start of Line” (SOL) sync code at the start of
a line within the frame. The protocol will also transmit an
“End of Frame” (EOF) at the end of a frame and an “End of
Line” (EOL) sync code at the end of a row within the frame
HiSPi Streaming Mode Protocol Layer
The protocol layer is positioned between the output data
path of the sensor and the physical layer. The main functions
of the protocol layer are generating sync codes, formatting
pixel data, inserting horizontal/vertical blanking codes, and
distributing pixel data over defined data lanes.
The HiSPi interface can only be configured when the
sensor is in standby. This includes configuring the interface
to transmit across 1, 2, or all 4 data lanes.
Protocol Fundamentals
Referring to Figure 12, it can be seen that a SYNC code
is inserted in the serial data stream prior to each line of image
Figure 12. Steaming vs. Packetized Transmission
www.onsemi.com
12
MT9J003
Parallel Pixel Data Interface
horizontal blanking and vertical blanking is programmable;
LV is HIGH during the shaded region of the figure. FV
timing is described in the “Output Data Timing (Parallel
Pixel Data Interface)”.
MT9J003 image data is read out in a progressive scan.
Valid image data is surrounded by horizontal blanking and
vertical blanking, as shown in Figure 13. The amount of
00 00 00 ..................................... 00 00 00
00 00 00 ..................................... 00 00 00
00 00 00 .................. 00 00 00
00 00 00 .................. 00 00 00
VERTICAL BLANKING
VERTICAL/HORIZONTAL
BLANKING
00 00 00 ..................................... 00 00 00
00 00 00 ..................................... 00 00 00
00 00 00 .................. 00 00 00
00 00 00 .................. 00 00 00
P0,0 P0,1 P0,2.....................................P0,n−1 P0,n
P1,0 P1,1 P1,2..................................... P1,n−1 P1,n
00 00 00 .................. 00 00 00
00 00 00 .................. 00 00 00
HORIZONTAL
BLANKING
VALID IMAGE
Pm−1,0 Pm−1,1................................. Pm−1,n−1 Pm−1,n 00 00 00 .................. 00 00 00
Pm,0 Pm,1................................. Pm,n−1 Pm,n
00 00 00 .................. 00 00 00
Figure 13. Spatial Illustration of Image Readout
Output Data Timing (Parallel Pixel Data Interface)
This allows PIXCLK to be used as a clock to sample the data.
PIXCLK is continuously enabled, even during the blanking
period. The MT9J003 can be programmed to delay the
PIXCLK edge relative to the DOUT transitions. This can be
achieved by programming the corresponding bits in the
row_speed register. The parameters P, A, and Q in Figure 15
are defined in Table 4.
MT9J003 output data is synchronized with the PIXCLK
output. When LV is HIGH, one pixel value is output on the
12-bit DOUT output every PIXCLK period. The pixel clock
frequency can be determined based on the sensor’s master
input clock and internal PLL configuration. The rising edges
on the PIXCLK signal occurs one-half of a pixel clock
period after transitions on LV, FV, and DOUT (see Figure 14).
LV
PIXCLK
P0 [11:0]
DOUT[11:0]
Blanking
P1 [11:0]
P2 [11:0]
P3 [11:0]
P4 [11:0]
P5 Pn−2 Pn−1[11:0]
Valid Image Data
Figure 14. Pixel Data Timing Example
www.onsemi.com
13
Pn [11:0]
Blanking
MT9J003
FV
LV
Number of
master clocks
P
A
Q
A
Q
A
P
Figure 15. Row Timing and FV/LV Signals
The sensor timing (shown in Table 4) is shown in terms of
pixel clock and master clock cycles (see Figure 14). The
default settings for the on-chip PLL generate
a pixel array clock (vt_pix_clk) of 160 MHz and an output
clock (op_pix_clk) of 40 MHz given a 20 MHz input clock
to the MT9J003. Equations for calculating the frame rate are
given in “Frame Rate Control”.
Table 4. ROW TIMING WITH HiSPi INTERFACE
Parameter
Name
Equation
Default Timing
PIXCLK_
PERIOD
Pixel Clock Period
1/vt_pix_clk_freq_mhz
1 Pixel Clock
= 6.25 ns
S
Skip (Subsampling)
Factor
For x_odd_inc = y_odd_inc = 3, S = 2.
For x_odd_inc = y_odd_inc = 7, S = 4.
otherwise, S = 1
For y_odd_inc = 3, S = 2
For y_odd_inc = 7, S = 4
For y_odd_inc = 15, S = 8
For y_odd_inc = 31, S = 16
For y_odd_inc = 63, S = 32
1
A
Active Data Time
(x_addr_end – x_addr_start + x_odd_inc) * 0.5 * PIXCLK_PERIOD/S
= 3775 – 112 + 12
1832 Pixel Clock
= 11.45 μs
P
Frame Start/end
Blanking
6 * PIXCLK_PERIOD
6 Pixel Clock
= 37.5 ns
Q
Horizontal Blanking
(line_length_pck – A) * PIXCLK_PERIOD
= 3694 – 1832
1862 Pixel Clock
= 11.63 μs
Row Time
line_length_pck * PIXCLK_PERIOD
3694 Pixel Clock
= 23.09 μs
N
Number of Rows
(y_addr_end – y_addr_start + y_odd_inc) / S = (2755 – 8 + 1)/1
2748 Rows
V
Vertical Blanking
((frame_length_lines – N) * (A + Q)) + Q – (2 * P)
= (2891 – 2748) * 3694 + 1862 − 12
530092 Pixel Clock
= 3.31 ms
T
Frame Valid Time
(N * (A + Q)) – Q + (2 * P)
= 2748*3694 – 1862 + 12
10149262 Pixel Clock
= 63.42 ms
F
Total Frame Time
line_length_pck * frame_length_lines * PIXCLK_PERIOD
= 2891 * 3694
10679354 Pixel Clock
= 66.75 ms
A+Q
www.onsemi.com
14
MT9J003
Table 5. ROW TIMING WITH PARALLEL INTERFACE
Parameter
Name
Equation
Default Timing
PIXCLK_
PERIOD
Pixel Clock Period
1/vt_pix_clk_freq_mhz
1 Pixel Clock
= 6.25 ns
S
Skip (Subsampling)
Factor
For x_odd_inc = y_odd_inc = 3, S = 2.
For x_odd_inc = y_odd_inc = 7, S = 4.
otherwise, S = 1
For y_odd_inc = 3, S = 2
For y_odd_inc = 7, S = 4
For y_odd_inc = 15, S = 8
For y_odd_inc = 31, S = 16
For y_odd_inc = 63, S = 32
1
A
Active Data Time
(x_addr_end – x_addr_start + x_odd_inc) * 0.5 * PIXCLK_PERIOD/S
= (3775 – 112+1)/2
1832 Pixel Clocks
= 11.45 μs
P
Frame Start/end
Blanking
6 * PIXCLK_PERIOD
6 Pixel Clocks
= 75 ns
Q
Array Horizontal
Blanking
(line_length_pck – A) * PIXCLK_PERIOD
= 7358 – 1832
5526 Pixel Clocks
= 34.5 μs
External horizontal
blanking is 30 pixel
clocks or 187 ns.
Row Time Limited by
Output Interface
Speed
x_output_size * clk_pixel/clk_op + 30
= 3664 * 160 MHz/80 MHz + 30
7358 Pixel Clocks
= 46.1 μs
N
Number of Rows
(y_addr_end − y_addr_start + y_odd_inc) / S
= (2755 – 8 + 1)/1
2748 rows
V
Vertical Blanking
((frame_length_lines – N) * (A + Q)) + Q – (2 * P)
= (2891 – 2748)*7358 + 1862 – 12
1054044 Pixel Clocks
= 6.59 ms
T
Frame Valid Time
(N * (A + Q)) – Q + (2 * P)
= 2748 * 7358 – 1862 + 12
20217934 Pixel Clocks
= 126.36 ms
F
Total Frame Time
line_length_pck * frame_length_lines * PIXCLK_PERIOD
= 2891 * 37358
21271978 Pixel Clocks
= 132.95 ms
A+Q
Table 6. ROW TIMING WITH PARALLEL INTERFACE USING LOW POWER MODE
Parameter
Name
Equation
Default Timing
PIXCLK_
PERIOD
Pixel Clock Period
1/vt_pix_clk_freq_mhz
1 Pixel Clock
= 12.5 ns
S
Skip (Subsampling)
Factor
For x_odd_inc = y_odd_inc = 3, S = 2.
For x_odd_inc = y_odd_inc = 7, S = 4.
otherwise, S = 1
For y_odd_inc = 3, S = 2
For y_odd_inc = 7, S = 4
For y_odd_inc = 15, S = 8
For y_odd_inc = 31, S = 16
For y_odd_inc = 63, S = 32
1
A
Active Data Time
(x_addr_end – x_addr_start + x_odd_inc) * 0.5 * PIXCLK_PERIOD/S
= (3775−112+1)/2
1832 Pixel Clocks
= 22.9 μs
P
Frame Start/end
Blanking
6 * PIXCLK_PERIOD
6 Pixel Clocks
= 75 ns
www.onsemi.com
15
MT9J003
Table 6. ROW TIMING WITH PARALLEL INTERFACE USING LOW POWER MODE (continued)
Parameter
Q
Name
Equation
Default Timing
Array Horizontal
Blanking
(line_length_pck – A) * PIXCLK_PERIOD
= 3694 – 1832
1862 Pixel Clocks
= 23.2 μs
External horizontal
blanking is 30 pixel
clocks or 375 ns.
Row Time Limited by
Output Interface
Speed
x_output_size * clk_pixel/clk_op + 30
= 3664 * 80 MHz/80 MHz + 30
3694 Pixel Clocks
= 46.1 μs
N
Number of Rows
(y_addr_end – y_addr_start + y_odd_inc) / S
= (2755 – 8 + 1)/1
2748 Rows
V
Vertical Blanking
((frame_length_lines – N) * (A + Q)) + Q – (2 * P)
= (2891 – 2748) * 7358 + 1862 – 12
530092 Pixel Clocks
= 6.63 ms
T
Frame Valid Time
(N * (A + Q)) – Q + (2 * P)
= 2748 * 3694 – 1862 + 12
10149262 Pixel Clocks
= 126.86 ms
F
Total Frame Time
line_length_pck * frame_length_lines * PIXCLK_PERIOD
= 2891 * 3694
10679354 Pixel Clocks
= 133.5 ms
A+Q
www.onsemi.com
16
MT9J003
Frame Rates at Common Resolutions
Table 7 shows examples of register settings to achieve
common resolutions and their frame rates.
Table 7. REGISTER SETTINGS FOR COMMON RESOLUTIONS
Resolution
3664x2748
(Full Resolution)
1920x1080
(1080p HDTV)
Interface
Frame
Rate
Subsampling
Mode
x_addr_start
x_addr_end
y_addr_start
y_addr_end
HiSPi
14.7 fps
N/A
112
3775
8
2755
Parallel
7.5 fps
HiSPi
59.94 fps
2 x 2 Summing
32
3873
296
2453
Parallel
29.97 fps
1280x720
(720p HDTV)
HiSPi and
Parallel
59.94 fps
2 x 2 Summing
32
3873
296
2453
1408x792 + 10% EIS
(720p HDTV + 10% EIS)
HiSPi and
Parallel
59.94 fps
2 x 2 Summing
624
3437
304
1885
640x480
(Low Power Monitor)
HiSPi and
Parallel
29.97 fps
Sum2Skip2
112
3769
8
2753
TWO-WIRE SERIAL REGISTER INTERFACE
The two-wire serial interface bus enables read/write
access to control and status registers within the MT9J003.
The interface protocol uses a master/slave model in which
a master controls one or more slave devices. The sensor acts
as a slave device. The master generates a clock (SCLK) that
is an input to the sensor and is used to synchronize transfers.
Data is transferred between the master and the slave on a
bidirectional signal (SDATA). SDATA is pulled up to VDD
off-chip by a 1.5 kΩ resistor. Either the slave or master
device can drive SDATA LOW-the interface protocol
determines which device is allowed to drive SDATA at any
given time.
The protocols described in the two-wire serial interface
specification allow the slave device to drive SCLKLOW; the
MT9J003 uses SCLK as an input only and therefore never
drives it LOW.
generating a stop condition; this is known as a “repeated
start” or “restart” condition.
Stop Condition
A stop condition is defined as a LOW-to-HIGH transition
on SDATA while SCLK is HIGH.
Data Transfer
Data is transferred serially, 8 bits at a time, with the MSB
transmitted first. Each byte of data is followed by an
acknowledge bit or a no-acknowledge bit. This data transfer
mechanism is used for the slave address/data direction byte
and for message bytes.
One data bit is transferred during each SCLK clock
period. SDATA can change when SCLK is LOW and must be
stable while SCLK is HIGH.
Slave Address
Bits [7:1] of this byte represent the device slave address
and bit [0] indicates the data transfer direction. A “0” in bit
[0] indicates a WRITE, and a “1” indicates a READ. The
default slave addresses used by the MT9J003 for the MIPI
configured sensor are 0x6C (write address) and 0x6D (read
address) in accordance with the MIPI specification.
Alternate slave addresses of 0x6E (write address) and 0x6F
(read address) can be selected by enabling and asserting the
SADDR signal through the GPI pad. But for the CCP2
configured sensor, the default slave addresses used are 0x20
(write address) and 0x21 (read address) in accordance with
the SMIA specification. Also, alternate slave addresses of
0x30 (write address) and 0x31 (read address) can be selected
by enabling and asserting the SADDR signal through the GPI
pad.
An alternate slave address can also be programmed
through R0x31FC.
Protocol
Data transfers on the two-wire serial interface bus are
performed by a sequence of low-level protocol elements:
1. a (repeated) start condition
2. a slave address/data direction byte
3. an (a no-) acknowledge bit
4. a message byte
5. a stop condition
The bus is idle when both SCLK and SDATA are HIGH.
Control of the bus is initiated with a start condition, and the
bus is released with a stop condition. Only the master can
generate the start and stop conditions.
Start Condition
A start condition is defined as a HIGH-to-LOW transition
on SDATA while SCLK is HIGH. At the end of a transfer, the
master can generate a start condition without previously
www.onsemi.com
17
MT9J003
place. This transfer takes place as two 8-bit sequences and
the slave sends an acknowledge bit after each sequence to
indicate that the byte has been received. The master then
transfers the data as an 8-bit sequence; the slave sends an
acknowledge bit at the end of the sequence. The master stops
writing by generating a (re)start or stop condition.
If the request was a READ, the master sends the 8-bit write
slave address/data direction byte and 16-bit register address,
the same way as with a WRITE request. The master then
generates a (re)start condition and the 8-bit read slave
address/data direction byte, and clocks out the register data,
eight bits at a time. The master generates an acknowledge bit
after each 8-bit transfer. The slave’s internal register address
is automatically incremented after every 8 bits are
transferred. The data transfer is stopped when the master
sends a no-acknowledge bit.
Message Byte
Message bytes are used for sending register addresses and
register write data to the slave device and for retrieving
register read data.
Acknowledge Bit
Each 8-bit data transfer is followed by an acknowledge bit
or a no-acknowledge bit in the SCLK clock period following
the data transfer. The transmitter (which is the master when
writing, or the slave when reading) releases SDATA. The
receiver indicates an acknowledge bit by driving SDATA
LOW. As for data transfers, SDATA can change when SCLK
is LOW and must be stable while SCLK is HIGH.
No-Acknowledge Bit
The no-acknowledge bit is generated when the receiver
does not drive SDATA LOW during the SCLK clock period
following a data transfer. A no-acknowledge bit is used to
terminate a read sequence.
Single READ From Random Location
This sequence (Figure 16) starts with a dummy WRITE to
the 16-bit address that is to be used for the READ. The
master terminates the WRITE by generating a restart
condition. The master then sends the 8-bit read slave
address/data direction byte and clocks out one byte of
register data. The master terminates the READ by
generating a no-acknowledge bit followed by a stop
condition. Figure 16 shows how the internal register address
maintained by the MT9J003 is loaded and incremented as
the sequence proceeds.
Typical Sequence
A typical READ or WRITE sequence begins by the
master generating a start condition on the bus. After the start
condition, the master sends the 8-bit slave address/data
direction byte. The last bit indicates whether the request is
for a read or a write, where a “0” indicates a write and a “1”
indicates a read. If the address matches the address of the
slave device, the slave device acknowledges receipt of the
address by generating an acknowledge bit on the bus.
If the request was a WRITE, the master then transfers the
16-bit register address to which the WRITE should take
Previous Reg Address, N
S
Slave
Address
0 A
S = Start Condition
P = Stop Condition
Sr = Restart Condition
A = Acknowledge
A = No-acknowledge
Reg
Address[15:8]
A
Reg Address, M
Reg
Address[7:0]
A Sr
Slave Address
1 A
Read Data
M+1
A
P
Slave to Master
Master to Slave
Figure 16. Single READ from Random Location
Single READ From Current Location
master terminates the READ by generating a
no-acknowledge bit followed by a stop condition. The figure
shows two independent READ sequences.
This sequence (Figure 17) performs a read using the
current value of the MT9J003 internal register address. The
Previous Reg Address, N
S
Slave Address
1 A
Read Data
Reg Address, N+1
A P
S
Slave Address
1 A
N+2
Read Data
A P
Figure 17. Single READ from Current Location
Sequential READ, Start From Random Location
has been transferred, the master generates an acknowledge
bit and continues to perform byte READs until “L” bytes
have been read.
This sequence (Figure 18) starts in the same way as the
single READ from random location (Figure 16). Instead of
generating a no-acknowledge bit after the first byte of data
www.onsemi.com
18
MT9J003
Previous Reg Address, N
S
Slave Address
0 A Reg Address[15:8]
M+1
Read Data
A Reg Address[7:0]
M+2
A
Read Data
Reg Address, M
A Sr
M+3
Slave Address
M+L−2
A
1 A
M+1
Read Data
M+L−1
Read Data
A
Read Data
A
M+L
A P
Figure 18. Sequential READ, Start from Random Location
Sequential READ, Start From Current Location
has been transferred, the master generates an acknowledge
bit and continues to perform byte READs until “L” bytes
have been read.
This sequence (Figure 19) starts in the same way as the
single READ from current location (Figure 17). Instead of
generating a no-acknowledge bit after the first byte of data
Previous Reg Address, N
S Slave Address 1 A
N+1
Read Data
A
N+2
Read Data
A
N+L−1
Read Data
A
N+L
Read Data
A
P
Figure 19. Sequential READ, Start from Current Location
Single WRITE to Random Location
then LOW bytes of the register address that is to be written.
The master follows this with the byte of write data. The
WRITE is terminated by the master generating a stop
condition.
This sequence (Figure 20) begins with the master
generating a start condition. The slave address/data
direction byte signals a WRITE and is followed by the HIGH
Previous Reg Address, N
S
Slave Address
0 A
Reg Address[15:8]
Reg Address, M
A
A
Reg Address[7:0]
M+1
A
A
Write Data
P
Figure 20. Single WRITE to Random Location
Sequential WRITE, Start at Random Location
has been transferred, the master generates an acknowledge
bit and continues to perform byte WRITEs until “L” bytes
have been written. The WRITE is terminated by the master
generating a stop condition.
This sequence (Figure 21) starts in the same way as the
single WRITE to random location (Figure 20). Instead of
generating a no-acknowledge bit after the first byte of data
Previous Reg Address, N
S
Slave Address
0 A
M+1
Write Data
Reg Address[15:8]
A
M+2
A
Write Data
Reg Address, M
Reg Address[7:0]
M+3
A
Write Data
M+L−2
A
Write Data
19
A
M+L−1
A
Figure 21. Sequential WRITE, Start at Random Location
www.onsemi.com
M+1
Write Data
M+L
A
A
P
MT9J003
PROGRAMMING RESTRICTIONS
The following sections list programming rules that must
be adhered to for correct operation of the MT9J003.
Table 8. DEFINITIONS FOR PROGRAMMING RULES
Definition
Name
xskip
xskip = 1 if x_odd_inc = 1; xskip = 2 if x_odd_inc = 3; xskip = 4 if x_odd_inc = 7
yskip
yskip = 1 if y_odd_inc = 1; yskip = 2 if y_odd_inc = 3; yskip = 4 if y_odd_inc = 7;
yskip = 8 if y_odd_inc = 15; yskip = 16 if y_odd_inc = 31; yskip = 32 if y_odd_inc = 63
image size generated by the scaler. The MT9J003 will
operate incorrectly if the x_output_size and y_output_size
are significantly larger than the output image. To understand
the reason for this, consider the situation where the sensor is
operating at full resolution and the scaler is enabled with a
scaling factor of 32 (half the number of pixels in each
direction). This situation is shown in Figure 22.
X Address Restrictions
The minimum column address available for the sensor is
24. The maximum value is 3879.
Effect of Scaler on Legal Range of Output Sizes
When the scaler is enabled, it is necessary to adjust the
values of x_output_size and y_output_size to match the
Core output: full resolution, x_output_size = x_addr_end − x_addr_start + 1
LINE_VALID
PIXEL_VALID
Scaler output: scaled to half size
LINE_VALID
PIXEL_VALID
Limiter output: scaled to half size, x_output_size = x_addr_end − x_addr_start + 1
LINE_VALID
PIXEL_VALID
Figure 22. Effect of Limiter on the Data Path
Because the scaler has reduced the amount of valid pixel
data without reducing the row time, the limiter attempts to
pad the row with (N/2) additional pixels. If this has the effect
of extending LV across the whole of the horizontal blanking
time, the MT9J003 will cease to generate output frames.
A correct configuration is shown in Figure 23, in addition
to showing the x_output_size reduced to match the output
size of the scaler. In this configuration, the output of the
limiter does not extend LV.
Figure 23 also shows the effect of the output FIFO, which
forms the final stage in the data path. The output FIFO
merges the intermittent pixel data back into a contiguous
stream. Although not shown in this example, the output
FIFO is also capable of operating with an output clock that
is at a different frequency from its input clock.
In Figure 22, three different stages in the data path (see
“Timing Specifications”) are shown. The first stage is the
output of the sensor core. The core is running at full
resolution and x_output_size is set to match the active array
size. The LV signal is asserted once per row and remains
asserted for N pixel times. The PIXEL_VALID signal
toggles with the same timing as LV, indicating that all pixels
in the row are valid.
The second stage is the output of the scaler, when the
scaler is set to reduce the image size by one-half in each
dimension. The effect of the scaler is to combine groups of
pixels. Therefore, the row time remains the same, but only
half the pixels out of the scaler are valid. This is signaled by
transitions in PIXEL_VALID. Overall, PIXEL_VALID is
asserted for (N/2) pixel times per row.
The third stage is the output of the limiter when the
x_output_size is still set to match the active array size.
www.onsemi.com
20
MT9J003
Core output: full resolution, x_output_size = x_addr_end − x_addr_start + 1
LINE_VALID
PIXEL_VALID
Scaler output: scaled to half size
LINE_VALID
PIXEL_VALID
Limiter output: scaled to half size, x_output_size = (x_addr_end − x_addr_start + 1)/2
LINE_VALID
PIXEL_VALID
Output FIFO: scaled to half size, x_output_size = (x_addr_end − x_addr_start + 1)/2
LINE_VALID
PIXEL_VALID
Figure 23. Timing of Data Path
Changing Registers While Streaming
The following registers should only be reprogrammed
while the sensor is in software standby:
• vt_pix_clk_div
• vt_sys_clk_div
• pre_pll_clk_div
• pll_multiplier
• op_pix_clk_div
• op_sys_clk_div
Output Data Timing
The output FIFO acts as a boundary between two clock
domains. Data is written to the FIFO in the VT (video
timing) clock domain. Data is read out of the FIFO in the OP
(output) clock domain.
When the scaler is disabled, the data rate in the VT clock
domain is constant and uniform during the active period of
each pixel array row readout. When the scaler is enabled, the
data rate in the VT clock domain becomes intermittent,
corresponding to the data reduction performed by the scaler.
A key constraint when configuring the clock for the output
FIFO is that the frame rate out of the FIFO must exactly
match the frame rate into the FIFO. When the scaler is
disabled, this constraint can be met by imposing the rule that
the row time on the serial data stream must be greater than
or equal to the row time at the pixel array. The row time on
the serial data stream is calculated from the x_output_size
and the data_format (8, 10, or 12 bits per pixel), and must
include the time taken in the serial data stream for start of
frame/row, end of row/frame and checksum symbols.
CAUTION: If this constraint is not met, the FIFO will
either underrun or overrun. FIFO underrun or
overrun is a fatal error condition that is
signalled through the data path_status
register (R0x306A).
Programming Restrictions When Using Global Reset
Interactions between the registers that control the global
reset imposes some programming restrictions on the way in
which they are used; these are discussed in ”Global Reset”.
www.onsemi.com
21
MT9J003
CONTROL OF THE SIGNAL INTERFACE
This section describes the operation of the signal interface
in all functional modes.
Parallel Pixel Data Interface
The parallel pixel data interface uses these output-only
signals:
• FV
• LV
• PIXCLK
• DOUT[11:0]
Serial Register Interface
The serial register interface uses these signals:
• SCLK
• SDATA
• SADDR (through the GPI pad)
The parallel pixel data interface is disabled by default at
power up and after reset. It can be enabled by programming
R0x301A. Table 10 shows the recommended settings.
When the parallel pixel data interface is in use, the serial
data output signals can be left unconnected. Set
reset_register[12] to disable the serializer while in parallel
output mode.
SCLK is an input-only signal and must always be driven
to a valid logic level for correct operation; if the driving
device can place this signal in High-Z, an external pull-up
resistor should be connected on this signal.
SDATA is a bidirectional signal. An external pull-up
resistor should be connected on this signal.
SADDR is a signal, which can be optionally enabled and
controlled by a GPI pad, to select an alternate slave address.
These slave addresses can also be programmed through
R0x31FC.
This interface is described in detail in ”Two-Wire Serial
Register Interface”.
Output Enable Control
When the parallel pixel data interface is enabled, its
signals can be switched asynchronously between the driven
and High-Z under pin or register control, as shown in
Table 9. Selection of a pin to use for the OE_N function is
described in ”General Purpose Inputs”.
Table 9. OUTPUT ENABLE CONTROL
OE_N Pin
Drive Signals R0x301A–B[6]
Description
Disabled
0
Interface High-Z
Disabled
1
Interface Driven
1
0
Interface High-Z
X
1
Interface Driven
0
X
Interface Driven
Configuration of the Pixel Data Interface
Fields in R0x301A are used to configure the operation of
the pixel data interface. The supported combinations are
shown in Table 10.
Table 10. CONFIGURATION OF THE PIXEL DATA INTERFACE
Serializer Disable
R0x301
A–B[12]
Parallel
Enable
R0x301A–B[7]
Standby
End-of-Frame
R0x301A–B[4]
0
0
1
Power up default.
Serial pixel data interface and its clocks are enabled. Transitions to soft
standby are synchronized to the end of frames on the serial pixel data
interface
1
1
0
Parallel pixel data interface, sensor core data output. Serial pixel data
interface and its clocks disabled to save power. Transitions to soft
standby are synchronized to the end of the current row readout on the
parallel pixel data interface
1
1
1
Parallel pixel data interface, sensor core data output. Serial pixel data
interface and its clocks disabled to save power. Transitions to soft
standby are synchronized to the end of frames in the parallel pixel data
interface
Description
www.onsemi.com
22
MT9J003
System States
The sensor’s operation is broken down into three separate
states: hardware standby, software standby, and streaming.
The transition between these states might take a certain
amount of clock cycles as outlined in Table 11.
The system states of the MT9J003 are represented as a
state diagram in Figure 24 and described in subsequent
sections. The effect of RESET_BAR on the system state and
the configuration of the PLL in the different states are shown
in Table 11.
Power supplies turned off
(asychronous from any state)
Powered Off
Por active
(only if POR is
on sensor)
POR = 0
RESET_BAR = 0
RESET _BAR transitions 1 −> 0
(asynchronous from any state )
Hardware
Standby
2400 EXTCLK
Cycles
Two-wire Serial
Interface Write
software_reset = 1
RESET_BAR = 1
Software reset initiated
(synchronous from any state)
Internal
Initialization
Initialization Timeout
Software
Standby
Two-wire Serial
Interface Write
mode_select = 1
PLL not locked
PLL Lock
Frame in
progress
PLL locked
Wait for Frame
End
Streaming
Two-wire Serial
Interface Write
mode_select = 0
Figure 24. MT9J003 System States
Table 11. RESET_BAR AND PLL IN SYSTEM STATES
State
EXTCLKs
PLL
Powered Off
−
VCO Powered Down (Note 1)
POR Active
−
Hardware Standby
0
Internal Initialization
1
Software Standby
PLL Lock
VCO Powering Up and Locking, PLL Output Bypassed
Streaming
VCO Running, PLL Output Active
Wait for Frame End
1. VCO = voltage-controlled oscillator.
www.onsemi.com
23
MT9J003
Power-On Reset Sequence
the operational value for the register (0x2800 if R0x0000 is
read).
When the sensor leaves software standby mode and
enables the VCO, an internal delay will keep the PLL
disconnected for up to 1ms so that the PLL can lock. The
VCO lock time is 200 μs(typical), 1 ms (maximum).
When power is applied to the MT9J003, it enters a
low-power hardware standby state. Exit from this state is
controlled by the later of two events:
1. The negation of the RESET_BAR input.
2. A timeout of the internal power-on reset circuit.
It is possible to hold RESET_BAR permanently
de-asserted and rely upon the internal power-on reset circuit.
When RESET_BAR is asserted it asynchronously resets
the sensor, truncating any frame that is in progress.
When the sensor leaves the hardware standby state it
performs an internal initialization sequence that takes 2400
EXTCLK cycles. After this, it enters a low-power software
standby state. While the initialization sequence is in
progress, the MT9J003 will not respond to READ
transactions on its two-wire serial interface. Therefore, a
method to determine when the initialization sequence has
completed is to poll a sensor register; for example, R0x0000.
While the initialization sequence is in progress, the sensor
will not respond to its device address and READs from the
sensor will result in a NACK on the two-wire serial interface
bus. When the sequence has completed, READs will return
Soft Reset Sequence
The MT9J003 can be reset under software control by
writing “1” to software_reset (R0x0103). A software reset
asynchronously resets the sensor, truncating any frame that
is in progress. The sensor starts the internal initialization
sequence, while the PLL and analog blocks are turned off.
At this point, the behavior is exactly the same as for the
power-on reset sequence.
Signal State During Reset
Table 12 shows the state of the signal interface during
hardware standby (RESET_BAR asserted) and the default
state during software standby. After exit from hardware
standby and before any registers within the sensor have been
changed from their default power-up values.
Table 12. SIGNAL STATE DURING RESET
Pad Name
Pad Type
EXTCLK
Input
Enabled. Must be driven to a valid logic level
RESET_BAR
(XSHUTDOWN)
Input
Enabled. Must be driven to a valid logic level
GPI[3:0]
Hardware Standby
Software Standby
Powered down. Can be left disconnected/floating
TEST
Enabled. Must be driven to a logic 0 for a serial CCP2-configured sensor, or 1 for a serial MIPI-configured sensor
SCLK
Enabled. Must be pulled up or driven to a valid logic level
SDATA
I/O
LINE_VALID
Output
Enabled as an input. Must be pulled up or driven to a valid logic level
High-Z. Can be left disconnected or floating
FRAME_VALID
DOUT[11:0]
PIXCLK
SLVS0_P
SLVS0_N
SLVS1_P
SLVS1_N
SLVS2_P
SLVS2_N
SLVS3_P
SLVS3_N
CLK_P
CLK_N
High-Z.
FLASH
SHUTTER
www.onsemi.com
24
Logic 0.
MT9J003
General Purpose Inputs
The gpi_status register is used to associate a function with
a general purpose input.
The MT9J003 provides four general purpose inputs. After
reset, the input pads associated with these signals are
powered down by default, allowing the pads to be left
disconnected/floating.
The general purpose inputs are enabled by setting
reset_register[8] (R0x301A). Once enabled, all four inputs
must be driven to valid logic levels by external signals. The
state of the general purpose inputs can be read through
gpi_status[3:0] (R0x3026).
In addition, each of the following functions can be
associated with none, one, or more of the general purpose
inputs so that the function can be directly controlled by a
hardware input:
• Output enable (see “Output Enable Control”)
• Trigger (see the sections below)
• Standby functions
• SADDR selection (see “Serial Register Interface”)
Streaming/Standby Control
The MT9J003 can be switched between its soft standby
and streaming states under pin or register control, as shown
in Table 13. Selection of a pin to use for the STANDBY
function is described in “General Purpose Inputs”. The state
diagram for transitions between soft standby and streaming
states is shown in Figure 24.
Table 13. STREAMING/STANDBY
Standby
Streaming R0x301A–B[2]
Description
Disabled
0
Soft Standby
Disabled
1
Streaming
−
0
Soft Standby
0
1
Streaming
1
−
Soft Standby
Trigger Control
as shown in Table 14. Selection of a pin to use for the
TRIGGER function is described in “General Purpose
Inputs”.
When the global reset feature is in use, the trigger for the
sequence can be initiated either under pin or register control,
Table 14. TRIGGER CONTROL
Trigger
Global Trigger R0x3160–1[0]
Description
Disabled
0
Idle
Disabled
1
Trigger
0
0
Idle
−
1
Trigger
1
−
Trigger
www.onsemi.com
25
MT9J003
PLL
clock applied on EXTCLK, a VCO to multiply the prescaler
output, and a set of dividers to generate the output clocks.
The clocking structure is shown in Figure 25.
The sensor contains a PLL for timing generation and
control. The PLL contains a prescaler to divide the input
External input clock
ext_clk_freq_mhz
EXTCLK
row_speed [2:0]
1 (1, 2, 4)
vt_pix_clk_div
3 (2, 3, 4, 5, 6,7, 8)
PLL output clock
clk_pixel
clk_pixel
1(1, 2, 4, 6, 8)
Divider
PLL input clock
vt pix
PLL internal VCO
pll_ip_clk_freq
clk
vt_pix_clk
frequency
Divider
vt sys clk
Divider
PLL
vt_sys_clk
Pre PLL
Multiplier
Divider
(m)
op sys clk
op_sys_clk
Divider
pre_pll_clk_div
(n)
2 (1−64)
pll_multiplier
(m)
64 (32−128)
op pix
clk
Divider
1(1, 2, 4, 6, 8)
op_pix_clk
clk_op
Divider
op_pix_clk_div
12 (8, 10, 12)
clk_op
row_speed [10:8]
1 (1, 2, 4)
Figure 25. Clocking Structure
Figure 25 shows the different clocks and the register
names. It also shows the default setting for each
divider/multiplier control register, and the range of legal
values for each divider/multiplier control register. The vt
and op sys clk Divider is hardwired in the design. The PLL
default settings support the HiSPi interface.
clk_pixel_freq_mhz +
From the diagram, the clock frequencies can be calculated
for the HiSPi interface using a 15 MHz input clock as
follows:
Internal pixel clock used to readout the pixel array:
15 MHz
ext_clk_freq_mhz
pll_multiplier
+
2 3
pre_pll_clk_div
vt_pix_clk_div
row_speed [2 : 0]
64
+ 160 MHz
1
(eq. 1)
64
+ 40 MHz
1
(eq. 2)
The external pixel clock used to output the data:
clk_op_freq_mhz +
15 MHz
ext_clk_freq_mhz
pll_multiplier
+
2 12
pre_pll_clk_div
op_pix_clk_div
row_speed [10 : 8]
Internal master clock:
vt_pix_clk_freq_mhz
2
(eq. 3)
The parameter limit register space contains registers that
declare the minimum and maximum allowable values for:
• The frequency allowable on each clock.
• The divisors that are used to control each clock.
•
The following factors determine what are valid values, or
combinations of valid values, for the divider/multiplier
control registers:
• The minimum/maximum frequency limits for the
associated clock must be met.
♦ pll_ip_clk_freq must be in the range 6–48 MHz.
Higher frequencies are preferred.
• PLL internal VCO frequency must be in the range
384–768 MHz.
•
•
The minimum/maximum value for the
divider/multiplier must be met.
♦ Range for m: 32–128.
♦ Range for (n): 1–64.
The op_pix_clk must never run faster than the
vt_pix_clk to ensure that the output data stream is
contiguous.
When using the HiSPi serial interface, the op_pix_clk
must be 1/4 of the vt_pix_clk.
The op_pix_clk_div divider must match the bit-depth
of the image when using HiSPi. For example,
op_pix_clk_div must be set to 12 for a 12-bit HiSPi
output. The is not required when using the parallel
interface.
When using the parallel interface, the op_pix_clk must
be half of the vt_pix_clk.
www.onsemi.com
26
MT9J003
• The output line time (including the necessary blanking)
• clk_op is used to load parallel pixel data from the
Although the PLL VCO input frequency range is
advertised as 6–48 MHz, superior performance is obtained
by keeping the VCO input frequency as high as possible.
The usage of the output clocks is shown below:
• clk_pixel is used by the sensor core to control the
timing of the pixel array. The sensor core produces one
12-bit pixel each vt_pix_clk period. The line length
(line_length_pck) and fine integration time
(fine_integration_time) are controlled in increments of
the clk_pixel period.
An example of the parallel configuration for the PLL will
uses an input clock of 10 MHz, an internal pixel clock of 160
MHz, and an output clock of 80 MHz. In this configuration:
• n=1
• m = 64
• vt_sys_clk_div = 2
• op_sys_clk_div = 1
• vt_pix_clk_div = 2
• op_pix_clk_div = 8
must be output in a time equal to or less than the time
defined by line_length_pck.
output FIFO. The output FIFO generates one pixel each
op_pix_clk period.
Internal pixel clock used to readout the pixel array:
clk_pixel_freq_mhz +
10 MHz
ext_clk_freq_mhz
pll_multiplier
+
1 2
pre_pll_clk_div
vt_pix_clk_div
row_speed [2 : 0]
64
+ 160 MHz
2
(eq. 4)
64
+ 80 MHz
8
(eq. 5)
The external pixel clock used to output the data:
clk_op_freq_mhz +
10 MHz
ext_clk_freq_mhz
pll_multiplier
+
1 1
pre_pll_clk_div
op_pix_clk_div
row_speed [10 : 8]
Programming the PLL Divisors
Clock Control
The PLL divisors must be programmed while the
MT9J003 is in the software standby state. After
programming the divisors, wait for the VCO lock time
before enabling the PLL. The PLL is enabled by entering the
streaming state.
An external timer will need to delay the entrance of the
streaming mode by 1 millisecond so that the PLL can lock.
The effect of programming the PLL divisors while the
MT9J003 is in the streaming state is undefined.
The MT9J003 uses an aggressive clock-gating
methodology to reduce power consumption. The clocked
logic is divided into a number of separate domains, each of
which is only clocked when required.
When the MT9J003 enters a low-power state, almost all
of the internal clocks are stopped. The only exception is that
a small amount of logic is clocked so that the two-wire serial
interface continues to respond to READ and WRITE
requests.
www.onsemi.com
27
MT9J003
FEATURES
Scaler
and distinguish various module types based on lens, IR-cut
filter, or other properties.
During the programming process, a dedicated pin for high
voltage needs to be provided to perform the anti-fusing
operation. This voltage (VPP) would need to be 8.5 V +3%.
Instantaneous VPP cannot exceed 9 V at any time. The
completion of the programming process will be
communicated by a register through the two-wire serial
interface.
Because this programming pin needs to sustain a higher
voltage than other input/output pins, having a dedicated high
voltage pin (VPP) minimizes the design risk. If the module
manufacturing process can probe the sensor at the die or
PCB level (that is, supply all the power rails, clocks,
two-wire serial interface signals), then this dedicated high
voltage pin does not need to be assigned to the module
connector pinout. However, if the VPP pin needs to be
bonded out as a pin on the module, the trace for VPP needs
to carry a maximum of 1mA is needed for programming
only. This pin should be left floating once the module is
integrated to a design. If the VPP pin does not need to be
bonded-out as a pin on the module, it should be left floating
inside the module.
The programming of the OTP memory requires the sensor
to be fully powered and remain in software standby with its
clock input applied. The information will be programmed
through the use of the two-wire serial interface, and once the
data is written to an internal register, the programming host
machine will apply a high voltage to the programming pin,
and send a program command to initiate the anti-fusing
process. After the sensor has finished programming the OTP
memory, a status bit will be set to indicate the end of the
programming cycle, and the host machine can poll the
setting of the status bit through the two-wire serial interface.
Only one programming cycle for the 16-bit word can be
performed.
Reading the OTP memory data requires the sensor to be
fully powered and operational with its clock input applied.
The data can be read through a register from the two-wire
serial interface.
The steps below describe the process to program and
verify the programmed data in the OTP memory:
1. Apply power to all the power rails of the sensor
(VDD, VDD_IO, VAA, VAA_PIX, VDD_PLL, and
VDD_TX0).
z Set VAA to 3.1 V during OTP memory
programming phase.
z VPP needs to be floated during this phase.
z Other supplies at nominal.
2. Provide 24 MHz EXTCLK clock input. The PLL
settings are discussed at the end of the document.
3. Perform the proper reset sequence to the sensor.
4. Place the sensor in soft standby
(sensor default state upon power-up) or ensure the
The MT9J003 sensor includes scaling capabilities. This
allows the user to generate full field-of-view, low resolution
images. Scaling is advantageous because it uses all pixel
values to calculate the output image which helps to avoid
aliasing. It is also more convenient than binning because the
scale factor varies smoothly and the user is not limited to
certain ratios of size resolution.
The scaling factor is programmable in 1/16 steps.
ScaleFactor +
♦
♦
scale_n
16
+
scale_m
scale_m
(eq. 6)
scale_n is fixed at 16.
scale_m is adjustable with R0x0404
Legal values for m are 16 through 128. The user has
the ability to scale from 1:1 (m = 16) to 1:8
(m = 128).
Shading Correction
Lenses tend to produce images whose brightness is
significantly attenuated near the edges. There are also other
factors causing color plane nonuniformity in images
captured by image sensors. The cumulative result of all these
factors is known as image shading. The MT9J003 has an
embedded shading correction module that can be
programmed to counter the shading effects on each
individual Red, GreenB, GreenR, and Blue color signal.
The Correction Function
Color-dependent solutions are calibrated using the sensor,
lens system and an image of an evenly illuminated,
featureless gray calibration field. From the resulting image,
register values for the color correction function
(coefficients) can be derived.
The correction functions can then be applied to each pixel
value to equalize the response across the image as follows:
Pcorrected (row, col) + Psensor (row, col)
♦
f(row, col)
(eq. 7)
where P are the pixel values and f is the color
dependent correction functions for each color
channel.
Each function includes a set of color-dependent
coefficients defined by registers R0x3600–3726. The
function’s origin is the center point of the function used in
the calculation of the coefficients. Using an origin near the
central point of symmetry of the sensor response provides
the best results. The center point of the function is
determined by ORIGIN_C (R0x3782) and ORIGIN_R
(R0x3784) and can be used to counter an offset in the system
lens from the center of the sensor array.
One-Time Programmable Memory
The MT9J003 has a two-byte OTP memory that can be
utilized during module manufacturing to store specific
information about the module. This feature provides system
integrators and module manufacturers the ability to label
www.onsemi.com
28
MT9J003
12. Remove high voltage and float VPP pin.
13. Power down the sensor.
14. Apply nominal power to all the power rails of the
sensor VDD, VDD_IO, VAA, VAA_PIX and
VDD_PLL). VPP must be floated.
15. Set EXTCLK to normal or customer defined
operating frequency.
16. Perform the proper reset sequence to the sensor.
17. Initiate the OTP memory reading process by
setting R0x304A[4] to the value 0x0010.
18. Poll the register bit R0x304A[6] until bit set to “1”
to check for read completion.
19. Read the 16 bit word data from the R0x304E.
streaming is turned OFF when the part is in active
mode.
5. VPP ramps to 8.5 V in preparation to program.
Power supply (VPP) slew rate should be slower
than 1 V/μs.
6. Program R0x3052 to the value 0x045C.
7. Program R0x3054 to the value 0XEA99.
8. Write the 16 bit word data by programming
R0x304C.
9. Initiate the OTP memory programming process by
programming R0x304A[0] to the value 0x0001.
10. Check R0x304A [2] = 1, until bit is set to “1” to
check for program completion.
11. Repeat steps 9 and 10 two more times.
Power Supplies
RESET_BAR
EXTCLK
SCLK/SDATA
VPP
Information to be
programmed to the register.
Initiate programming
and poll status bit.
Read programmed
values for status.
Figure 26. Sequence for Programming the MT9J003
SENSOR READOUT CONFIGURATION
Image Acquisition Modes
MT9J003 switches cleanly from the old
integration time to the new while only generating
frames with uniform integration. See “Changes to
Integration Time” in the MT9J003 Register
Reference.
2. Global reset mode:
This mode can be used to acquire a single image at
the current resolution. In this mode, the end point
of the pixel integration time is controlled by an
external electromechanical shutter, and the
MT9J003 provides control signals to interface to
that shutter. The operation of this mode is
described in detail in ”Global Reset”.
The MT9J003 supports two image acquisition modes:
1. Electronic rolling shutter (ERS) mode:
This is the normal mode of operation. When the
MT9J003 is streaming; it generates frames at a
fixed rate, and each frame is integrated (exposed)
using the ERS. When the ERS is in use, timing
and control logic within the sensor sequences
through the rows of the array, resetting and then
reading each row in turn. In the time interval
between resetting a row and subsequently reading
that row, the pixels in the row integrate incident
light. The integration (exposure) time is controlled
by varying the time between row reset and row
readout. For each row in a frame, the time between
row reset and row readout is fixed, leading to a
uniform integration time across the frame. When
the integration time is changed (by using the
two-wire serial interface to change register
settings), the timing and control logic controls the
transition from old to new integration time in such
a way that the stream of output frames from the
The benefit of using an external electromechanical shutter
is that it eliminates the visual artifacts associated with ERS
operation. Visual artifacts arise in ERS operation,
particularly at low frame rates, because an ERS image
effectively integrates each row of the pixel array at a
different point in time.
www.onsemi.com
29
MT9J003
Window Control
Readout Modes
The sequencing of the pixel array is controlled by the
x_addr_start, y_addr_start, x_addr_end, and y_addr_end
registers. For both parallel and serial interfaces, the output
image size is controlled by the x_output_size and
y_output_size registers.
Horizontal Mirror
When the horizontal_mirror bit is set in the
image_orientation register, the order of pixel readout within
a row is reversed, so that readout starts from x_addr_end and
ends at x_addr_start. Figure 27 shows a sequence of 6 pixels
being read out with horizontal_mirror = 0 and
horizontal_mirror = 1. Changing horizontal_mirror causes
the Bayer order of the output image to change; the new
Bayer order is reflected in the value of the pixel_order
register.
Pixel Border
The default settings of the sensor provide a 3840
(H) x 2748 (V) image. A border of up to 8 pixels (4 in
binning) on each edge can be enabled by reprogramming the
x_addr_start, y_addr_start, x_addr_end, y_addr_end,
x_output_size, and y_output_size registers accordingly.
This provides a total active pixel array of 3856 (H) x 2764
(V) including border pixels.
LINE_VALID
horizontal_mirror = 0
DOUT[11:0]
G0[11:0] R0[11:0] G1[11:0] R1[11:0] G2[11:0] R2[11:0]
horizontal_mirror = 1
DOUT[11:0]
R2[11:0] G2[11:0] R1[11:0] G1[11:0] R0[11:0] G0[11:0]
Figure 27. Effect of Horizontal Mirror on Readout Order
being read out with vertical_flip = 0 and vertical_flip = 1.
Changing vertical_flip causes the Bayer order of the output
image to change; the new Bayer order is reflected in the
value of the pixel_order register.
Vertical Flip
When the vertical_flip bit is set in the image_orientation
register, the order in which pixel rows are read out is
reversed, so that row readout starts from y_addr_end and
ends at y_addr_start. Figure 28 shows a sequence of 6 rows
FRAME_VALID
vertical_flip = 0
DOUT[11:0]
vertical_flip = 1
DOUT[11:0]
Row0[11:0]
Row1[11:0]
Row2[11:0]
Row3[11:0] Row4[11:0]
Row5[11:0]
Row5[11:0]
Row4[11:0]
Row3[11:0]
Row2[11:0] Row1[11:0]
Row0[11:0]
Figure 28. Effect of Horizontal Mirror on Readout Order
www.onsemi.com
30
MT9J003
array. The most common subsampling used is either a 2x2
or 4x4 where every 2nd or 4th pixel is read in the x and y
direction.
Subsampling
The MT9J003 supports subsampling. This feature allows
the sensor to read out a sample of pixels available on the
2 x 2 skipping
Full Resolution
Figure 29. Pixel Array Readout Without Subsampling and With 2x2 Skipping
Pixel skipping can be configured up to 4x in the
x-direction and 32x in the y-direction. Skipping pixels in the
x-direction will reduce the row-time while skipping in the
y-direction will reduce the number of rows readout from the
sensor. Skipping in both directions will reduce the
frame-time and is a common method used to increase the
sensor frame-rate. Skipping will introduce image artifacts
from aliasing.
Skip 2x
Skip 32x, 16x, or 8x
Skip 4x
Figure 30. Combinations of Pixel Skipping in the MT9J003 Sensor
www.onsemi.com
31
MT9J003
The subsampling feature can also bin or sum the skipped
pixels. Pixel binning will sample pixels and average the
value together in the analog domain. Summing will add the
charge or voltage values of the neighboring pixels together.
2 x 2 Binning or Summing
Binning
Summing
v
avg
avg
avg
e−
avg
e−
v
Figure 31. Pixel Binning and Summing
summing and skipping implementation will sum
neighboring pixels on the same color plane and skip over the
adjacent group of pixels.
Figure 32 shows that neighboring pixels are summed
together. In the case that a subsampling factor of 4x or
greater is used with summing, the neighboring pixels will
also be summed together.
The pixel summing must be done with adjacent pixels
within the same color plane. The pixel binning can be
configured to combine adjacent pixels or to combine every
other pixel.
The pixel subsampling can be configured as a
combination of skipping and binning or summing. This type
of subsampling is typically used to achieve the best
combination of pixel responsivity and frame rate. The
Figure 32. Pixel Skipping Combined with Summing or Binning
Table 15 shows the different combinations of
subsampling available with the MT9J003 sensor. The sensor
cannot combine pixels using two different methods in the
same direction. This means that bin-xy and sum-y are not
valid combinations with the sensor. As well, the bin-xy is
limited to a skip of 4x in the vertical direction.
www.onsemi.com
32
MT9J003
Table 15. SUBSAMPLING COMBINATIONS
Skip Y
Skip X
1
2
4
8
16
32
Bin X
Bin XY
Sum X
Sum XY
1
–
2
Y
–
–
–
–
Y
–
4
Y
–
Y
–
1
–
–
–
Y
2
Y
Y
Y
Y
4
Y
Y
Y
Y
1
–
–
–
Y
2
Y
Y
Y
Y
4
Y
Y
Y
Y
1
–
–
–
Y
2
Y
–
Y
Y
4
Y
–
Y
Y
1
–
–
–
Y
2
Y
–
Y
Y
4
Y
–
Y
Y
1
–
–
–
Y
2
Y
–
Y
Y
4
Y
–
Y
Y
Frame Rate Control
can be determined as the largest value found in Equation 8.
These are the required values for either the array readout or
the bandwidth available to the parallel or serial interface.
The frame-time is calculated as the row-time multiplied
by the number of rows (frame_length_lines). The row-time
is referred to in these calculations as the number of pixel
clocks read per row (line_length_pck) multiplied by the
vt_pix_clk frequency.
The formulas for calculating the frame rate of the
MT9J003 are shown below.
The line length is programmed in pixel clock periods
through the register line_length_pck. The minimum value
Absolute Minimum Array Line Length Pck
minimum line_length_pck = min_line_length_pck (see
Table 16, “Minimum Row Time and Blanking Numbers”)
Array Readout Line Length Pck
ȱx_addr_end–x_addr_start ) x_odd_inc ) min_line_blanking_pckȳ
ȧ
ȧ
x_odd_inc)1
)
2x(
Ȳ
ȴ
2
Interface Line Length Pck
ǒ
x_output_size
Ǔ
op_pix_clk
) 30 (For Parallel)
vt_pix_clk
ǒx_output_size
Ǔ
4
determines the frame-rate of the output interface. The
frame-rate using HiSPi will always be higher than using the
parallel interface. Values for min_line_blanking_pck are
provided in “Minimum Row Time”.
The frame length is programmed directly in number of
lines in the register frame_line_length. For a specific
window size, the minimum frame length is shown in
Equation 11:
(eq. 9)
op_pix_clk
) 30 (ForHiSPi) (eq. 10)
vt_pix_clk
Note that line_length_pck will be the maximum of the
three equations. The second equation describes the
limitations from the readout of the pixel array while the third
minimumframe_length_lines +
ǒ
(eq. 8)
y_addr_end * y_addr_start ) 1
) min_frame_blanking_lines
subsampling factor
www.onsemi.com
33
Ǔ
(eq. 11)
MT9J003
The frame rate can be calculated from these variables and
the pixel clock speed as shown in Equation 12:
frame rate +
vt_pixel_clock_mhz
1 10 6
(eq. 12)
line_length_pck_xframe_length_lines
If coarse_integration_time is set larger than
frame_length_lines the frame size will be expanded to
coarse_integration_time + 1.
Minimum Row Time
The minimum row time and blanking values with default
register settings are shown in Table 16.
Table 16. MINIMUM ROW TIME AND BLANKING NUMBERS
No Row Binning
Register
row_speed[2:0]
Row Binning
1
2
4
1
2
4
min_line_blanking_pck
0x046E
0x029A
0x01B0
0x0822
0x046C
0x0292
min_line_length_pck
0x0670
0x03E0
0x02F0
0x0CC0
0x0660
0x03D8
Parallel − line_length_pck > (x_output_size) *
“vt_pix_clk period” / “op_pix_clk period” +
0x005E.
HiSPi (4-lane) − line_length_pck >
(1/4)*(x_output_size) * “vt_pix_clk period” /
“op_pix_clk period” + 0x005E.
In addition, enough time must be given to the output FIFO
so it can output all data at the set frequency within one row
time.
There are therefore three checks that must all be met when
programming line_length_pck:
1. line_length_pck> min_line_length_pck in
Table 16.
2. line_length_pck > 0.5 * (x_addr_end −
x_addr_start + x_odd_inc)/((1+x_odd_inc)/2) +
min_line_blanking_pck in Table 16.
3. The row time must allow the FIFO to output all
data during each row.
Minimum Frame Time
The minimum number of rows in the image is 2, so
min_frame_length_lines
will
always
equal
(min_frame_blanking_lines + 2).
Table 17. MINIMUM FRAME TIME AND BLANKING NUMBERS
Register
min_frame_blanking_lines
0x008F
min_frame_length_lines
0x0091
time_max_margin. Values for different mode combinations
are shown in Table 18.
Fine Integration Time Limits
The limits for the fine_integration_time can be found
from fine_integration_time_min and fine_integration_
Table 18. FINE_INTEGRATION_TIME LIMITS
No Row Binning
Register
row_speed[2:0]
1
2
fine_integration_time_min
0x03F2
fine_integration_time_max_margin
0x027E
Row Binning
4
1
2
4
0x020A
0x094
0x07B2
0x03AE
0x010C
0x012E
0x0108
0x050E
0x0276
0x0224
www.onsemi.com
34
MT9J003
Fine Correction
For the fine_integration_time limits, the fine_correction
constant will change with the pixel clock speed and binning
mode. These values are shown in Table 19.
Table 19. FINE_CORECTION VALUES
No Row Binning
Register
Row Binning
row_speed[2:0]
1
2
4
1
2
4
fine_correction
0x09C
0x048
0x01E
0x0134
0x094
0x044
Low Power Mode
achieved with low power mode are lower than in full power
mode.
Because only internal pixel clock speeds of 1, 2, and 4 are
supported, low power mode combined with pc_speed[2:0]
= 4 is an illegal combination.
Any limitations related to changing the internal pixel
clock speed will also apply to low power mode, because it
automatically changes the pixel clock speed. Therefore, the
limiter registers need to be reprogrammed to match the new
internal pixel clock frequency.
The MT9J003 sensor supports a low power mode, which
can be entered by programming register bit read_mode[9].
Setting this bit will do the following:
• Double the value of pc_speed[2:0] internally. This
means halving the internal pixel clock frequency.
• Lower currents in the analog domain. This can be done
by setting a low power bit in the static control register.
The current will be halved where appropriate in the
analog domain.
Integration Time
Note that enabling the low power mode will not put the
sensor in subsampling mode. This will have to be
programmed separately as described earlier in this
document. Low power is independent of the readout mode
and can also be enabled in full resolution mode. Because the
pixel clock speed is halved, the frame rates that can be
The integration (exposure) time of the MT9J003 is
controlled
by
the
fine_integration_time
and
coarse_integration_time registers.
The limits for the fine integration time are defined by:
fine_integration_time_min ≤ fine_integration_time ≤ (line_length_pck–fine_integration_time_max_margin)
(eq. 13)
The limits for the coarse integration time are defined by:
coarse_integration_time_min t coarse_integration_time
(eq. 14)
The actual integration time is given by:
((coarse_integration_time line_length_pck) ) fine_integration_time)
(vt_pix_clk_freq_mhz 10 6)
(eq. 15)
coarse_integration_time t+ (frame_length_lines * coarse_integration_time_max_margin)
(eq. 16)
integration_time +
It is required that:
If this limit is exceeded, the frame time will automatically
be
extended
to
(coarse_integration_time
+
coarse_integartion_time_max_margin) to accommodate
the larger integration time.
www.onsemi.com
35
MT9J003
ON Semiconductor Gain Model
The registers provide three 2x and one 4x analog gain
stages. The first analog gain stage has a granularity of 64
steps over 2x gain. A digital gain from 1−7x can also be
applied.
The ON Semiconductor gain model uses color-specific
registers to control both analog and digital gain to the sensor.
These registers are:
• global_gain
• greenR_gain
• red_gain
• blue_gain
• greenB_gain
analog gain + (8ń(8 * g(colamp) t 11 : 9 u)x(1 ) color_gain[8])(1 ) color_gain[7])(color_gain[6 : 0]ń64)
Bits 11 to 9 are also restricted to 0, 4, and 6. This limits the
particular gain stage to 4x.
(eq. 17)
As a result of the different gain stages, analog gain levels
can be achieved in different ways. The recommended gain
sequence is shown below in Table 20.
Table 20. RECOMMENDED GAIN STAGES
Desired Gain
Recommended Gain Register Setting
1–1.98
0x1040–0x107F
2–3.97
0x1840–0x187F
4–7.94
0x1C40–0x1C7F
8–15.875
0x1CC0–0x1CFF
16–31.75
0x1DC0–0x1DFF
Flash Control
integration time. This can be avoided either by first enabling
mask bad frames (write reset_register[9] = 1) before the
enabling the flash or by forcing a restart (write
reset_register[1] = 1) immediately after enabling the flash;
the first bad frame will then be masked out, as shown in
Figure 35. Read-only bit flash[14] is set during frames that
are correctly integrated; the state of this bit is shown in
Figures 33, 34, and 35.
The MT9J003 supports both xenon and LED flash
through the FLASH output signal. The timing of the FLASH
signal with the default settings is shown in Figure 33, and in
Figure 34 and Figure 35. The flash and flash_count registers
allow the timing of the flash to be changed. The flash can be
programmed to fire only once, delayed by a few frames
when asserted, and (for xenon flash) the flash duration can
be programmed.
Enabling the LED flash will cause one bad frame, where
several of the rows only have the flash on for part of their
FRAME_VALID
Flash STROBE
State of triggered bit
(R0x3046−7[14])
Figure 33. Xenon Flash Enabled
www.onsemi.com
36
MT9J003
FRAME_VALID
Flash STROBE
State of triggered bit
(R0x3046−7[14])
Bad frame
Flash enabled
during this frame
Bad frame
Good frame
Good frame
Flash disabled
during this frame
Notes: 1. Integration time = number of rows in a frame.
2. Bad frames will be masked during LED flash operation when mask bad frames bit field is set (R0x301A[9] = 1).
3. An option to invert the flash output signal through R0x3046[7] is also available.
Figure 34. LED Flash Enabled
FRAME_VALID
Flash STROBE
State of triggered bit
(R0x3046−7[14])
Masked out
frame
Flash enabled
and a restart
triggered
Masked out
frame
Good frame
Good frame
Flash disabled
and a restart
triggered
Figure 35. LED Flash Enabled Following Forced Restart
Global Reset
4. All of the rows of the pixel array are taken out of
reset simultaneously. All rows start to integrate
incident light. The electromechanical shutter may
be open or closed at this time.
5. If the electromechanical shutter has been closed, it
is opened.
6. After the desired integration time
(controlled internally or externally to the
MT9J003), the electromechanical shutter is closed.
7. A single output frame is generated by the sensor
with the usual LV, FV, PIXCLK, and DOUT timing.
As soon as the output frame has completed (FV
de-asserts), the electromechanical shutter may be
opened again.
8. The sensor automatically resumes operation in
ERS mode.
Global reset mode allows the integration time of the
MT9J003 to be controlled by an external electromechanical
shutter. Global reset mode is generally used in conjunction
with ERS mode. The ERS mode is used to provide
viewfinder information, the sensor is switched into global
reset mode to capture a single frame, and the sensor is then
returned to ERS mode to restore viewfinder operation.
Overview of Global Reset Sequence
The basic elements of the global reset sequence are:
1. By default, the sensor operates in ERS mode and
the SHUTTER output signal is LOW. The
electromechanical shutter must be open to allow
light to fall on the pixel array. Integration time is
controlled by the coarse_integration_time and
fine_integration_time registers.
2. A global reset sequence is triggered.
3. All of the rows of the pixel array are placed in
reset.
This sequence is shown in Figure 36. The following
sections expand to show how the timing of this sequence is
controlled.
www.onsemi.com
37
MT9J003
ERS
Row Reset
Integration
Readout
ERS
Figure 36. Overview of Global Reset Sequence
automatically resumes operation in ERS mode. The first
frame integrated with ERS will be generated after a delay of
approximately:
((13 + coarse_integration_time) * line_length_pck)
This sequence is shown in Figure 37.
While operating in ERS mode, double-buffered registers
are updated at the start of each frame in the usual way.
During the global reset sequence, double-buffered registers
are updated just before the start of the readout phase.
Entering and Leaving the Global Reset Sequence
A global reset sequence can be triggered by a register
write to global_seq_trigger[0] (global trigger, to transition
this bit from a 0 to a 1) or by a rising edge on a
suitably-configured GPI input (see “Trigger Control”).
When a global reset sequence is triggered, the sensor waits
for the end of the current row. When LV de-asserts for that
row, FV is de-asserted 6 PIXCLK periods later, potentially
truncating the frame that was in progress.
The global reset sequence completes with a frame
readout. At the end of this readout phase, the sensor
Trigger
Wait for end of current row
ERS
Row Reset
Automatic at end of frame readout
Integration
Readout
ERS
Figure 37. Entering and Leaving a Global Reset Sequence
As soon as the global_rst_end count has expired, all rows
in the pixel array are simultaneously taken out of reset and
the pixel array begins to integrate incident light.
Programmable Settings
The registers global_rst_end and global_read_start allow
the duration of the row reset phase and the integration phase
to be controlled, as shown in Figure 38. The duration of the
readout phase is determined by the active image size.
Trigger
Automatic at end of frame readout
Wait for end of current row
ERS
Row Reset
Integration
Readout
ERS
global_rst_end
global_read_start
Figure 38. Controlling the Reset and Integration Phases of the Global Reset Sequence
point at which the shutter closes. Finally, the shutter opens
again after the end of the readout phase. In shutter example
2, the shutter is open during the initial ERS sequence and
closes sometime during the row reset phase. The shutter both
opens and closes during the integration phase. The pixel
array is integrating incident light for the part of the
integration phase during which the shutter is open. As for the
previous example, the shutter opens again after the end of
the readout phase.
Control of the Electromechanical Shutter
Figure 39 shows two different ways in which a shutter can
be controlled during the global reset sequence. In both cases,
the maximum integration time is set by the difference
between global_read_start and global_rst_end. In shutter
example 1, the shutter is open during the initial ERS
sequence and during the row reset phase. The shutter closes
during the integration phase. The pixel array is integrating
incident light from the start of the integration phase to the
www.onsemi.com
38
MT9J003
Trigger
Wait for end of current row
ERS
Row Reset
Automatic at end of frame readout
Integration
Readout
ERS
global_rst_end
global_read_start
maximum integration time
actual integration time
SHUTTER Example 1
shutter open
shutter closed
shutter open
shutter closed
shutter open
actual integration time
SHUTTER Example 2
shutter open
closed
shutter open
Figure 39. Control of the Electromechanical Shutter
The MT9J003 provides a SHUTTER output signal to
control (or help the host system control) the
electromechanical shutter. The timing of the SHUTTER
output is shown in Figure 40. SHUTTER is de-asserted by
default. The point at which it asserts is controlled by the
programming of global_shutter_start. At the end of the
global reset readout phase, SHUTTER de-asserts
approximately 2 * line_length_pck after the de-assertion of
FV.
This programming restriction must be met for correct
operation:
global_read_start >global_shutter_start
It is essential that the shutter remains closed during the
entire row readout phase (that is, until FV has de-asserted for
the frame readout); otherwise, some rows of data will be
corrupted (over-integrated).
It is essential that the shutter closes before the end of the
integration phase. If the row readout phase is allowed to start
before the shutter closes, each row in turn will be integrated
for one row-time longer than the previous row.
After FV de-asserts to signal the completion of the readout
phase, there is a time delay of approximately 10 *
line_length_pck before the sensor starts to integrate
light-sensitive rows for the next ERS frame. It is essential
that the shutter be opened at some point in this time window;
otherwise, the first ERS frame will not be uniformly
integrated.
Trigger
Automatic at end of frame readout
Wait for end of current row
ERS
Row Reset
Integration
Readout
ERS
global_rst_end
~2*line_length_pck
global_read_start
global_shutter_start
SHUTTER
Figure 40. Controlling the SHUTTER Output
global reset sequence. The FLASH output will assert a fixed
number of cycles after the start of the integration phase and
will remain asserted for a time that is controlled by the value
of the flash_count register, as shown in Figure 41.
Using FLASH with Global Reset
If global_seq_trigger[2] = 1 (global flash enabled) when
a global reset sequence is triggered, the FLASH output
signal will be pulsed during the integration phase of the
www.onsemi.com
39
MT9J003
Trigger
Wait for end of current row
ERS
Row Reset
Automatic at end of frame readout
Integration
Readout
ERS
global_rst_end
(fixed)
flash_count
FLASH
Figure 41. Using FLASH With Global Reset
When the trigger is de-asserted to end integration, the
integration phase is extended by a further time given by
global_read_start – global_shutter_start. Usually this
means that global_read_start should be set to
global_shutter_start + 1.
The operation of this mode is shown in Figure 42. The
figure shows the global reset sequence being triggered by the
GPI2 input, but it could be triggered by any of the GPI inputs
or by the setting and subsequence clearing of the
global_seq_trigger[0] under software control.
The integration time of the GRR sequence is defined as:
External Control of Integration Time
If global_seq_trigger[1] = 1 (global bulb enabled) when
a global reset sequence is triggered, the end of the
integration phase is controlled by the level of trigger
(global_seq_trigger[0] or the associated GPI input). This
allows the integration time to be controlled directly by an
input to the sensor.
This operation corresponds to the shutter “B” setting on a
traditional camera, where “B” originally stood for “Bulb”
(the shutter setting used for synchronization with a
magnesium foil flash bulb) and was later considered to stand
for “Brief” (an exposure that was longer than the shutter
could automatically accommodate).
IntegrationTime +
[global_read_start–global_shutter_start–global_rst_end]
global_scale
vt_pix_clk_freq_mhz
(eq. 18)
Where:
global_read_start + (2 16
global_shutter_start + (2 16
(eq. 19)
global_read_start2[7 : 0] ) global_read_start1[15 : 0]
global_shutter_start2[7 : 0] ) global_shutter_start1[15 : 0]
(eq. 20)
These programming restrictions must be met for correct
operation of bulb exposures:
• global_read_start > global_shutter_start
• global_shutter_start > global_rst_end
• global_shutter_start must be smaller than the exposure
time (that is, this counter must expire before the trigger
is de-asserted)
The integration equation allows for 24-bit precision when
calculating both the shutter and readout of the image. The
global_rst_end has only 16-bit as the array reset function
and requires a short amount of time.
The integration time can also be scaled using
global_scale. The variable can be set to
0–512, 1–2048, 2–128, and 3–32.
Trigger
Wait for end of current row
ERS
Row Reset
Automatic at end of frame readout
Integration
global_rst_end
Readout
ERS
global_read_start − global_shutter_start
GPI2
Figure 42. Global Reset Bulb
www.onsemi.com
40
MT9J003
frame out of the serial pixel data interface, including the
addition of two lines of embedded data. The values of the
coarse_integration_time
and
fine_integration_time
registers within the embedded data match the programmed
values of those registers and do not reflect the integration
time used during the global reset sequence.
Retriggering the Global Reset Sequence
The trigger for the global reset sequence is edge-sensitive;
the global reset sequence cannot be retriggered until the
global trigger bit (in the global_seq_trigger register) has
been returned to “0,” and the GPI (if any) associated with the
trigger function has been de-asserted.
The earliest time that the global reset sequence can be
retriggered is the point at which the SHUTTER output
de-asserts; this occurs approximately 2 * line_length_pck
after the negation of FV for the global reset readout phase.
The frame that is read out of the sensor during the global
reset readout phase has exactly the same format as any other
ERS
Row Reset
Global Reset and Soft Standby
If the mode_select[stream] bit is cleared while a global
reset sequence is in progress, the MT9J003 will remain in
streaming state until the global reset sequence (including
frame readout) has completed, as shown in Figure 43.
Integration
Readout
ERS
mode_select[streaming]
system state
Streaming
Figure 43. Entering Soft Standby During a Global Reset Sequence
www.onsemi.com
41
Software
Standby
MT9J003
SENSOR CORE DIGITAL DATA PATH
Test Patterns
test_pattern_mode (R0x0600–1). The test patterns are listed
in Table 21.
The MT9J003 supports a number of test patterns to
facilitate system debug. Test patterns are enabled using
Table 21. TEST PATTERNS
test_pattern_mode
Description
0
Normal operation: no test pattern
1
Solid color
2
100% color bars
3
Fade-to-gray color bars
4
PN9 link integrity pattern (only on sensors with serial interface)
256
Walking 1s (12-bit value)
257
Walking 1s (10-bit value)
258
Walking 1s (8-bit value)
Test patterns 0–3 replace pixel data in the output image
(the embedded data rows are still present). Test pattern 4
replaces all data in the output image (the embedded data
rows are omitted and test pattern data replaces the pixel
data).
HiSPi Test Patterns
Test patterns specific to the HiSPi are also generated. The
test patterns are enabled by using test_enable (R0x31C6 − 7)
and controlled by test_mode (R0x31C6[6:4]).
Table 22. HiSPi TEST PATTERNS
Description
test_mode
0
Transmit a constant 0 on all enabled data lanes
1
Transmit a constant 1 on all enabled data lanes
2
Transmit a square wave at half the serial data rate on all enabled data lanes
3
Transmit a square wave at the pixel rate on all enabled data lanes
4
Transmit a continuous sequence of pseudo random data, with no SAV code, copied on all enabled data lanes
5
Replace data from the sensor with a known sequence copied on all enabled data lanes
are programmable in R0x31E8–R0x31EE. Both even and
odd cursor positions and widths are supported.
Each cursor can be inhibited by setting its width to “0.”
The programmed cursor position corresponds to the x and y
addresses of the pixel array. For example, setting
horizontal_cursor_position to the same value as
y_addr_start would result in a horizontal cursor being drawn
starting on the first row of the image. The cursors are opaque
(they replace data from the imaged scene or test pattern).
The color of each cursor is set by the values of the Bayer
components in the test_data_red, test_data_greenR,
test_data_blue and test_data_greenB registers. As a
consequence, the cursors are the same color as test pattern
1 and are therefore invisible when test pattern 1 is selected.
When vertical_cursor_position = 0x0FFF, the vertical
cursor operates in an automatic mode in which its position
advances every frame. In this mode the cursor starts at the
column associated with x_addr_start = 0 and advances by a
For all of the test patterns, the MT9J003 registers must be
set appropriately to control the frame rate and output timing.
This includes:
• All clock divisors
• x_addr_start
• x_addr_end
• y_addr_start
• y_addr_end
• frame_length_lines
• line_length_pck
• x_output_size
• y_output_size
Test Cursors
The MT9J003 supports one horizontal and one vertical
cursor, allowing a crosshair to be superimposed on the image
or on test patterns 1–3. The position and width of each cursor
www.onsemi.com
42
MT9J003
the value of image_orientation can be understood from these
implementation details:
• The test cursors are inserted last in the data path, the
cursor is applied with out any sensor corrections.
• The drawing of a cursor starts when the pixel array row
or column address is within the address range of cursor
start to cursor start + width.
• The cursor is independent of image orientation.
step-size of 8 columns each frame, until it reaches the
column associated with x_addr_start = 2040, after which it
wraps (256 steps). The width and color of the cursor in this
automatic mode are controlled in the usual way.
The effect of enabling the test cursors when the
image_orientation register is non-zero is not defined by the
design specification. The behavior of the MT9J003 is shown
in Figure 44 and the test cursors are shown as translucent, for
clarity. In practice, they are opaque (they overlay the imaged
scene). The manner in which the test cursors are affected by
Horizontal mirror = 0, Vertical flip = 0
Vertical cursor start
Horizontal mirror = 1, Vertical flip = 0
Readout
Direction
Vertical cursor start
Readout
Direction
Horizontal mirror = 1, Vertical flip = 1
Horizontal cursor start
Horizontal mirror = 0, Vertical flip = 1
Horizontal cursor start
Readout
Direction
Horizontal cursor start
Horizontal cursor start
Readout
Direction
Vertical cursor start
Vertical cursor start
Figure 44. Test Cursor Behavior With Image Orientation
www.onsemi.com
43
MT9J003
TIMING SPECIFICATIONS
Power-Up Sequence
4. After the last power supply is stable, enable
EXTCLK.
5. Assert RESET_BAR for at least 1ms.
6. Wait 2400 EXTCLKs for internal initialization
into software standby.
7. Configure PLL, output, and image settings to
desired values
8. Set mode_select = 1 (R0x0100).
9. Wait 1 ms for the PLL to lock before streaming
state is reached.
The recommended power-up sequence for the MT9J003
is shown in Figure 45. The available power supplies−
VDD_IO, VDD, VDD_TX, VDD_PLL, VAA, VAA_PIX,
VDD_SLVS, VDD_SLVS_TX− can be turned on at the same time
or have the separation specified below.
1. Turn on VDD_IO power supply.
2. After 1–500 ms, turn on VDD and VDD_TX power
supply.
3. After 1–500 ms, turn on VDD_PLL and
VAA/VAA_PIX power supplies.
VDD_IO
t1
VDD, VDD_SLVS, VDD_TX
t2
VDD_PLL
VAA, VAA_PIX
VDD_SLVS_TX
t3
t4
EXTCLK
t5
RESET_BAR
t6
Hard
Reset
t7
Internal
INIT
Software
Standby
PLL
Lock
Streaming
Figure 45. Power−Up Sequence
Table 23. POWER-UP SEQUENCE
Definition
Symbol
Min
Typ
Max
Unit
VDD_IO to VDD, VDD_TX Time
t1
0
–
500
ms
VDD, VDD_TX to VDD_PLL Time
t2
0
–
500
ms
VDD, VDD_TX to VAA/VAA_PIX Time
t3
0
–
500
ms
VAA, VAA_PIX to VDD_SLVS_TX
t4
−
–
500
ms
Active Hard Reset
t5
1
–
−
ms
Internal Initialization
t6
2400
–
−
EXTCLKs
PLL Lock Time
t7
1
–
−
ms
1. Digital supplies must be turned on before analog supplies.
Power-Down Sequence
1. Disable streaming if output is active by setting
mode_select = 0 (R0x0100).
2. The soft standby state is reached after the current
row or frame, depending on configuration, has
ended.
The recommended power-down sequence for the
MT9J003 is shown in Figure 46. The available power
supplies− VDD_IO, VDD, VDD_TX0, VDD_PLL, VAA,
VAA_PIX, VDD_SLVS, VDD_SLVS_TX− can be turned off
at the same time or have the separation specified below.
www.onsemi.com
44
MT9J003
3. Assert hard reset by setting RESET_BAR to a
logic “0.”
4. Turn off the VAA/VAA_PIX and VDD_PLL power
supplies.
5. After 1–500 ms, turn off VDD and VDD_TX0
power supply.
6. After 1–500 ms, turn off VDD_IO power supply.
t5
VDD_IO
VDD, VDD_SLVS, VDD_TX
VDD_PLL
t4
VAA, VAA_PIX
t3
VDD_SLVS_TX
t2
EXTCLK
RESET_BAR
t1
Hard
Reset
Software
Standby
Streaming
Turning Off Power Supplies
Figure 46. Test Cursor Behavior With Image Orientation
Table 24. POWER-DOWN SEQUENCE
Definition
Symbol
Min
Typ
Max
Unit
Hard reset
t1
1
–
–
ms
VDD_SLVS_TX to VDD time
t2
0
–
500
ms
VDD/VAA/VAA_PIX to VDD time
t3
0
–
500
ms
VDD_PLL to VDD time
t4
0
–
500
ms
VDD to VDD_IO time
t5
0
–
500
ms
Hard Standby and Hard Reset
2. The soft standby state is reached after the current
row or frame, depending on configuration, has
ended.
3. Assert RESET_BAR (active LOW) to reset the
sensor.
4. The sensor remains in hard standby state if
RESET_BAR remains in the logic “0” state.
The hard standby state is reached by the assertion of the
RESET_BAR pad (hard reset). Register values are not
retained by this action, and will be returned to their default
values once hard reset is completed. The minimum power
consumption is achieved by the hard standby state. The
details of the sequence are described below and shown in
Figure 47.
1. Disable streaming if output is active by setting
mode_select = 0 (R0x0100).
www.onsemi.com
45
MT9J003
EXTCLK
mode_select
R0x0100
next row/frame
Logic “1”
Logic “0”
RESET_BAR
Streaming
Soft Standby
Hard Standby from Hard Reset
Figure 47. Hard Standby and Hard Reset
Soft Standby and Soft Reset
2. The soft standby state is reached after the current
row or frame, depending on configuration, has
ended.
The MT9J003 can reduce power consumption by
switching to the soft standby state when the output is not
needed. Register values are retained in the soft standby state.
Once this state is reached, soft reset can be enabled
optionally to return all register values back to the default.
The details of the sequence are described below and shown
in Figure 48.
Soft Reset
1. Follow the soft standby sequence listed above.
2. Set software_reset = 1 (R0x0103) to start the
internal initialization sequence.
3. After 2400 EXTCLKs, the internal initialization
sequence is completed and the current state returns
to soft standby automatically. All registers,
including software_reset, return to their default
values.
Soft Standby
1. Disable streaming if output is active by setting
mode_select = 0 (R0x0100).
EXTCLK
next row/frame
mode_select
R0x0100
Logic “1”
Logic “0”
Logic “0”
Logic “0”
software_reset
R0x0103
Logic “0”
Logic “0”
Logic “1”
Logic “0”
2400 EXTCLKs
Streaming
Soft Standby
Soft Reset
Soft Standby
Figure 48. Soft Standby and Soft Reset
www.onsemi.com
46
MT9J003
SPECTRAL CHARACTERISTICS
50
Blue
45
G re e n
Red
40
Quantum Efficiency (%)
35
30
25
20
15
10
5
0
350
400
450
500
550
600
650
700
750
Wavelength (nm)
Figure 49. Quantum Efficiency
CRA vs. Image Height Plot
Image Height
0
0
0
5
0.191
0.67
10
0.382
1.34
15
0.574
2.01
20
0.765
2.68
25
0.956
3.35
30
1.147
4.03
35
1.339
4.70
40
1.530
5.37
45
1.721
6.04
50
1.912
6.71
55
2.103
7.38
6
60
2.295
8.05
65
2.486
8.72
4
70
2.677
9.39
75
2.868
10.06
80
3.059
10.73
85
3.251
11.41
90
3.442
12.08
95
3.633
12.75
100
3.824
13.42
20
18
16
14
CRA (deg)
CRA
(deg)
12
10
8
2
0
0
10
20
30
40
50
60
Image Height (%)
70
80
Figure 50. CRA (13.45)
www.onsemi.com
47
90
100
110
MT9J003
ELECTRICAL CHARACTERISTICS
Table 25. DC ELECTRICAL DEFINITIONS AND CHARACTERISTICS
(fEXTCLK = 15 MHz; VDD = 1.8 V; VDD_IO = 1.8 V; VAA = 2.8 V; VAA_PIX = 2.8 V; VDD_PLL = 2.8 V; VDD_SLVS = 1.8 V,
VDD_SLVS_TX = 0.8 V; Output load = 68.5 pF; TJ = 60°C; Data Rate = 480 MHz,; DLL set to 0, 10 Mp frame-rate at 14.7 fps)
Condition
Symbol
Min
Typ
Max
Unit
Core Digital Voltage
VDD
1.7
1.8
1.9
V
Core Digital Voltage
VDD
1.7
1.8
1.9
V
VDD_IO
1.7
1.8
1.9
V
VAA
2.4
2.8
3.1
V
Pixel Supply Voltage
VAA_PIX
2.4
2.8
3.1
V
PLL Supply Voltage
VDD_PLL
2.4
2.8
3.1
V
HiSPi Digital Voltage
VDD_SLVS
1.7
1.8
1.9
V
VDD_SLVS_TX
0.3
0.4
0.9
V
Definition
I/O Digital Voltage
Parallel Pixel Data Interface
Analog Voltage
HiSPi I/O Digital Voltage
Digital Operating Current
Streaming, Full Resolution
35
41
45
mA
I/O Digital Operating Current
Streaming, Full Resolution
0
0
0
mA
Analog Operating Current
Streaming, Full Resolution
132
169
190
mA
Pixel Supply Current
Streaming, Full Resolution
2.7
7.6
13.3
mA
PLL Supply Current
Streaming, Full Resolution
6.5
7
7.5
mA
HiSPi Digital Operating Current
Streaming, Full Resolution
n/a
20
n/a
mA
HiSPi I/O Digital Operating Current
Streaming, Full Resolution
13
13.5
14
mA
1.3
1.5
1.9
mW
Soft Standby (Clock On)
CAUTION:
Stresses greater than those listed in Table 20 may cause permanent damage to the device. This is a stress rating only, and
functional operation of the device at these or any other conditions above those indicated in the operational sections of this
specification is not implied.
Table 26. ABSOLUTE MAXIMUM RATINGS
Symbol
Definition
VDD_MAX
Condition
Min
Max
Unit
Core Digital Voltage
–0.3
1.9
V
VDD_IO_MAX
I/O Digital Voltage
–0.3
3.1
V
VAA_MAX
Analog Voltage
–0.3
3.5
V
VAA_PIX
Pixel Supply Voltage
–0.3
3.5
V
VDD_PLL
PLL Supply Voltage
–0.3
3.5
V
VDD_SLVS_MAX
HiSPi Digital Voltage
–0.3
1.9
V
VDD_SLVS_TX_MAX
HiSPi I/O Digital Voltage
–0.3
1.2
V
IDD
Digital Operating Current
–
90
mA
IDD_IO
I/O Digital Operating Current
–
100
mA
IAA_MAX
Analog Operating Current
–
225
mA
IAA_PIX
Pixel Supply Current
–6
25
mA
IDD_PLL
PLL Supply Current
–
25
mA
tOP
Operating Temperature
–30
70
°C
tST
Storage Temperature
–40
85
°C
Measure at Junction
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
2. To keep dark current and shot noise artifacts from impacting image quality, care should be taken to keep tOP at a minimum.
www.onsemi.com
48
MT9J003
Table 27. PARALLEL INTERFACE CONFIGURED TO USE LOW POWER MODE
(fEXTCLK = 15 MHz; VDD = 1.8 V; VDD_IO = 1.8 V; VAA = 2.8 V; VAA_PIX = 2.8 V; VDD_PLL = 2.8 V; TJ = 60°C;
Parallel Data Rate = 80 Mp/s)
Frame Rate
IAA
IDDPLL
IDD
IDDIO
IAAPIX
10 MP
7.5 fps
103.29
10.26
23.93
11.53
2.33
388 mW
720p60
59.94 fps
122.78
10.25
23.85
11.21
5.39
451 mW
1080p30
29.97 fps
114.67
10.26
22.89
4.49
4.14
411 mW
VGA60
59.94 fps
82.66
10.27
18.5
4.51
5.25
316 mW
Monitor
29.97 fps
69.22
10.28
16.3
6.35
2.76
271 mW
1. Monitor is a low power VGA preview mode. The power consumption values in this table represent a small sample of MT9J003 sensors. The
IDDIO current will double if the VDD_IO voltage is raised to 2.8V.
tr_clk
tSRTH
SCLK
tSDH tSDS
tSCLK
tSHAW
tf_clk
tr_sdat
tf_sdat
90%
90%
10%
10%
tSTPS tSTPH
tAHSW
SDATA
Write Address
Write Address
Register Address
Register Value
Bit 7
Bit 0
Bit 7
Bit 0
ACK
Write Start
tSHAR
SCLK
Stop
tAHSR
tSDHR tSDSR
SDATA
Read Start
Read Address
Read Address
Register Value
Register Value
Bit 7
Bit 0
Bit 7
Bit 0
ACK
1. Read sequence: For an 8-bit READ, read waveforms start after WRITE command and register address are issued.
Figure 51. Two-Wire Serial Bus Timing Parameters
Table 28. TWO-WIRE SERIAL REGISTER INTERFACE ELECTRICAL CHARACTERISTICS
(fEXTCLK = 15 MHz; VDD = 1.8 V; VDD_IO = 1.8 V; VAA = 2.8 V; VAA_PIX = 2.8 V; VDD_PLL = 2.8 V; VDD_SLVS = 1.8 V,
VDD_SLVS_TX = 0.4 V; Output load = 68.5 pF; TJ = 60°C; Data Rate = 480 MHz; DLL set to 0)
Symbol
Parameter
Condition
VIL
Input LOW voltage
IIN
Input leakage current
No pull up resistor;
VIN = VDD_IO or DGND
VOL
Output LOW voltage
At specified 2 mA
IOL
Output LOW current
At specified VOL 0.1 V
CIN
Input pad capacitance
CLOAD
Load capacitance
Min
Typ
Max
Unit
–0.5
0.73
0.3 x VDD_IO
V
2
μA
0.035
V
3
mA
6
pF
–2
0.031
0.032
pF
www.onsemi.com
49
MT9J003
Table 29. TWO−WIRE SERIAL REGISTER INTERFACE TIMING SPECIFICATION
(fEXTCLK = 15 MHz; VDD = 1.8 V; VDD_IO = 1.8 V; VAA = 2.8V; VAA_PIX = 2.8 V; VDD_PLL = 2.8 V; VDD_SLVS = 1.8 V,
VDD_SLVS_TX = 0.4 V; Output load = 68.5 pF; TJ = 60°C; Data Rate = 480 MHz,; DLL set to 0)
Symbol
Parameter
Condition
Min
Typ
Max
Unit
fSCLK
Serial Interface Input Clock
–
0
100
400
kHz
SCLK Duty Cycle
VOD
45
50
60
%
300
μs
tR
SCLK/SDATA Rise Time
tSRTS
Start Setup Time
Master WRITE to Slave
0.6
μs
tSRTH
Start Hold Time
Master WRITE to Slave
0.4
μs
tSDH
SDATA Hold
Master WRITE to Slave
0.3
tSDS
SDATA Setup
Master WRITE to Slave
0.3
tSHAW
SDATA Hold to ACK
Master READ to Slave
0.15
0.65
μs
tAHSW
ACK Hold to SDATA
Master WRITE to Slave
0.15
0.70
μs
0.65
μs
μs
tSTPS
Stop Setup Time
Master WRITE to Slave
0.3
μs
tSTPH
Stop Hold Time
Master WRITE to Slave
0.6
μs
tSHAR
SDATA Hold to ACK
Master WRITE to Slave
0.3
1.65
μs
tAHSR
ACK Hold to SDATA
Master WRITE to Slave
0.3
0.65
μs
tSDHR
SDATA Hold
Master READ from Slave
012
0.70
μs
tSDSR
SDATA Setup
Master READ from Slave
0.3
tR
tF
μs
tRP
tFP
90 %
90 %
10 %
10 %
tEXTCLK
EXTCLK
tPD
tPD
tCP
PIXCLK
Data[11:0]
Pxl_0
Pxl_1
Pxl_2
Pxl_n
tPFH
tPLH
tPFL
tPLL
FRAME_VALID/
LINE_VALID
FRAME_VALID leads LINE_VALID by 6 PIXCLKs.
Figure 52. I/O Timing Diagram
www.onsemi.com
50
FRAME_VALID trails
LINE_VALID by 6 PIXCLKs.
MT9J003
Table 30. I/O PARAMETERS
(fEXTCLK = 15 MHz; VDD = 1.8 V; VAA = 2.8 V; VAA_PIX = 2.8 V; VDD_PLL = 2.8 V; VDD_SLVS = 1.8 V, VDD_SLVS_TX = 0.4 V;
Output load = 68.5 pF; TJ = 60°C; Data Rate = 480 MHz,; DLL set to 0)
Symbol
Definition
Conditions
Min
Max
Units
VIH
Input HIGH Voltage
VDD_IO = 1.8V
1.4
V
VDD_IO = 2.8V
2.4
VDD_IO
+ 0.3
VDD_IO = 1.8V
GND – 0.3
0.4
VDD_IO = 2.8V
GND – 0.3
0.8
VIL
Input LOW Voltage
IIN
Input Leakage Current
No Pull-up Resistor; VIN = VDD OR DGND
– 20
20
μA
VOH
Output HIGH Voltage
At Specified IOH
VDD_IO − 0.4V
–
V
VOL
Output LOW Voltage
At Specified IOL
–
0.4
V
IOH
Output HIGH Current
At Specified VOH
–
–12
mA
IOL
Output LOW Current
At Specified VOL
–
9
mA
IOZ
Tri-state Output Leakage Current
–
10
μA
Table 31. I/O TIMING
(fEXTCLK = 15 MHz; VDD = 1.8 V; VDD_IO = 1.8 V; VAA = 2.8 V; VAA_PIX = 2.8 V; VDD_PLL = 2.8 V; VDD_SLVS = 1.8 V, VDD_SLVS_TX
= 0.4 V; Output load = 68.5 pF; TJ = 60°C; Data Rate = 480 MHz; DLL set to 0)
Symbol
Definition
Conditions
Min
Typ
Max
Units
fEXTCLK
Input Clock Frequency
PLL Enabled
6
24
48
MHz
tEXTCLK
Input Clock Period
PLL Enabled
166
41
20
ns
tR
Input Clock Rise Time
0.1
–
1
V/ns
tF
Input Clock Fall Time
0.1
–
1
V/ns
Clock Duty Cycle
45
50
55
%
tJITTER
Input Clock Jitter
–
–
0.3
ns
Output Pin Slew
Fastest
CLOAD = 15 pF
–
0.7
–
V/ns
fPIXCLK
PIXCLK Frequency
Default
–
80
–
MHz
tPD
PIXCLK to Data Valid
Default
–
–
3
ns
tPFH
PIXCLK to FRAME_VALID HIGH
Default
–
–
3
ns
tPLH
PIXCLK to LINE_VALID HIGH
Default
–
–
3
ns
tPFL
PIXCLK to FRAME_VALID LOW
Default
–
–
3
ns
tPLL
PIXCLK to LINE_VALID LOW
Default
–
–
3
ns
www.onsemi.com
51
MT9J003
tRISE
80%
DATA MASK
Vdiff
90%
TxPre
TxPost
tFALL
UI/2
Max Vdiff
UI/2
Vdiff
CLOCK MASK
Trigger/Reference
CLKJITTER
Figure 53. HiSPi Eye Diagram for Both Clock and Data Signals
Table 32. HiSPi RISE AND FALL TIMES AT 480 MHz
(Measurement Conditions: PHY Supply 1.8 V, HiSPi Power Supply 0.8 V, Data Rate 480 MHz, DLL set to 0)
Parameter
Name
Value
Unit
Max Setup Time from Transmitter
TxPRE
0.44
UI
Max Hold Time from Transmitter
TxPost
0.44
UI
Rise Time t
tRISE
350
ps
Fall Time t
tFALL
350
ps
66
Ω
Output Impedance
Table 33. HiSPi RISE AND FALL TIMES AT 360 MHz
(Measurement Conditions: PHY Supply 1.8 V, HiSPi Power Supply 0.8 V, Data Rate 480 MHz, DLL set to 0)
Parameter
Name
Value
Unit
Max Setup Time from Transmitter
TxPRE
0.48
UI
Max Hold Time from Transmitter
TxPost
0.42
UI
Rise Time t
tRISE
350
ps
Fall Time t
tFALL
350
ps
66
Ω
Output Impedance
www.onsemi.com
52
MT9J003
tCHSKEW1PHY
Figure 54. HiSPi Skew Between Data Signals Within the PHY
Table 34. CHANNEL, PHY AND INTRA-PHY SKEW
(Measurement Conditions: PHY Supply 1.8 V, HiSPi Power Supply 0.8 V, Data Rate 480 MHz, DLL set to 0)
tCHSKEW1PHY
Data Lane Skew in Reference to Clock
−150
ps
Table 35. CLOCK DLL STEPS
(Measurement Conditions: PHY Supply 1.8 V, HiSPi Power Supply 0.8 V, Data DLL set to 0)
Clock DLL Step
1
2
3
4
5
Step
Delay @ 480MHz
0.25
0.375
0.5
0.625
0.75
UI
Eye_opening@ 480 MHz
0.85
0.78
0.71
0.71
0.69
UI
Eye_opening@ 360 MHz
0.89
0.83
0.81
0.60
046
UI
1. The Clock DLL Steps 6 and 7 are not recommended by ON Semiconductor for the MT9J003 Rev. 2.
Table 36. DATA DLL STEPS
(Measurement Conditions: PHY Supply 1.8 V, HiSPi Power Supply 0.8 V, Clock DLL set to 0)
Data DLL Step
1
2
4
6
Step
Delay @ 480MHz
0.25
0.375
0.625
0.875
UI
Eye_opening@ 480 MHz
0.79
0.84
0.71
0.61
UI
Eye_opening@ 360 MHz
0.85
0.83
0.82
0.77
UI
1. The Data DLL Steps 3, 5, and 7 are not recommended by ON Semiconductor for the MT9J003 Rev. 2.
www.onsemi.com
53
MT9J003
(0, 2)
0.1 A
(1, 25)
Seating plane
A
0.1 A
10±0.075
7.7
0.7 Typ.
1.4±0.5
0.15 A B C
3.85
C
47X 0.8±0.05
0.15 A B C
4.2
4.5
10±0.075
7.7
3.85
0.7 Typ.
48X 0.4±0.05
0.15 A B C
4.5
9
0.725±0.075
5.014±0.075
Encapsulant2
First Clear Pixel
Substrate3
5.082±0.075
Lid4
Image sensor die6
(4.589 CTR)
7.5±0.10
CTR
7
Optical Area
Optical Center8
0.525±0.05
(0.125)
(6.413 CTR)
8±0.10
CTR
Section A − A
Notes: 1.
2.
3.
4.
5.
6.
7.
Dimensions in mm. Dimensions in () are for reference only.
Encapsulant: Epoxy
Substrate material: Plastic laminate 0.5 thickness
List material: Borosilicate glass 0.4 thickness. Refractive index at 20°C = 1.5255 @ 546 nm and 1.5231 @ 588 nm.
Lead finish: Gold plating, 0.5 microns minimum thickness.
Image sensor die 0.2 thickness.
Maximum rotation of optical area relative to seating plane A: 25 microns.
Maximum tilt of optical area relative to top of cover glass: 20 microns.
Maximum tilt of optical area relative to top of cover glass: 50 microns.
8. Die center = package center; optical center offset from package center: X = 0.01356, Y = −0.081705
Figure 55. Package Mechanical Drawing (CASE 847AK)
www.onsemi.com
54
MT9J003
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
◊
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
55
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MT9J003/D