® CLD DS-39 REV0 PRODUCT FAMILY DATA SHEET ® Cree XLamp ML-B LEDs PRODUCT DESCRIPTION FEATURES TABLE OF CONTENTS The Cree XLamp ML-B LED brings • Available in white (2,600 K Flux Characteristics (TJ = 25°C) . . . . . . 2 lighting-class reliability and performance to 1/4-watt LEDs. The XLamp ML-B expands Cree’s lighting-class leadership to linear and distributed lighting applications. With XLamp lighting-class reliability, a wide viewing angle, uniform light output, and industry-leading to 8,300 K CCT) • ANSI-compatible sub-bins • Maximum drive current: 175 mA • 120° viewing angle, uniform chromaticity profile • Electrically neutral thermal path chromaticity binning in a 3.5-mm • RoHS and REACH-compliant X 3.5-mm package, the XLamp • Unlimited floor life at ML-B LED continues Cree’s history ≤ 30°C/85% RH Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . 2 Relative Spectral Power Distribution. . . . . . . . . . . . . . . . . . . . . . . . . . 3 Relative Flux vs. Junction Temperature (IF = 80 mA). . . . . . . . 3 Electrical Characteristics (TJ = 25°C). . . . . . . . . . . . . . . . . . . . . . . . . . 4 Relative Flux vs. Current TJ = 25°C). . . . . . . . . . . . . . . . . . . . . . . . . . 4 Thermal Design. . . . . . . . . . . . . . . . . . . . . . . . . 5 Typical Spatial Distribution. . . . . . . . . . . . 5 of segment-focused product inno- Reflow Soldering Characteristics. . . . . . 6 vation in LEDs for lighting applica- Notes. . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . 7 tions. Mechanical Dimensions (TA = 25°C).. 8 Tape and Reel. . . . . . . . . . . . . . . . . . . . . . . . . . . 9 The XLamp ML-B LED brings high Packaging. . . . . . . . . . . . . . . . .. . . . . . . . . . . . . 10 performance and a smooth look to a wide range of lighting applications, including linear lighting, fluo- WWW. CREE.COM/XLAMP rescent retrofits and retail-display lighting. Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 XLAMP ML-B LEDS FLUX CHARACTERISTICS (TJ = 25°C) The following table provides several base order codes for XLamp ML-B LEDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the order-code nomenclature, please consult the XLamp ML-B LED Binning and Labeling document. Color Cool White Base Order Codes Min Luminous Flux (lm) @ 80 mA CCT Range Order Code Min. Max. Group Flux (lm) 5,000 K 8,300 K J0 23.5 MLBAWT-A1-0000-000W51 3,700 K 4,300 K H0 18.1 MLBAWT-A1-0000-000VE5 J0 23.5 MLBAWT-A1-0000-000WE5 2,800 K 3,200 K H0 18.1 MLBAWT-A1-0000-000VE7 J0 23.5 MLBAWT-A1-0000-000WE7 Warm White Notes: • Cree maintains a tolerance of +/- 7% on flux measurements. • Typical CRI for Cool White (4,300 K – 8,300 K CCT) is 75. • Typical CRI for Warm White (2,600 K – 4,300 K CCT) is 80. CHARACTERISTICS Characteristics Unit Thermal resistance, junction to solder point °C/W 25 degrees 120 mV/°C -3.5 Viewing angle (FWHM) Temperature coefficient of voltage ESD classification (HBM per Mil-Std-883D) DC forward current Minimum Typical Maximum Class 2 mA Reverse voltage V Forward voltage (@ 80 mA) V LED junction temperature °C 80 175 5 3.3 3.5 150 Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 2 XLAMP ML-B LEDS RELATIVE SPECTRAL POWER DISTRIBUTION Relative Radiant Power (%) 100 80 5000K - 8300K CCT 3500K - 5000K CCT 60 2600K - 3500K CCT 40 20 0 400 450 500 550 600 650 700 750 Wavelength (nm) RELATIVE FLUX VS. JUNCTION TEMPERATURE (IF = 80 MA) 100% Relative Luminous Flux 90% 80% 70% 60% 50% 40% 30% 20% 10% 0% 25 50 75 100 125 150 Junction Temperature (ºC) Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 3 XLAMP ML-B LEDS ELECTRICAL CHARACTERISTICS (TJ = 25°C) 180 Forward Current (mA) 160 140 120 100 80 60 40 20 0 2.50 2.75 3.00 3.25 3.50 3.75 4.00 Forward Voltage (V) RELATIVE FLUX VS. CURRENT (TJ = 25°C) Relative Luminous Flux (%) 200% 180% 160% 140% 120% 100% 80% 60% 40% 20% 0% 0 25 50 75 100 125 150 175 Forward Current (mA) Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 4 XLAMP ML-B LEDS THERMAL DESIGN The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics. 200 180 Maximum Current (mA) 160 140 120 100 80 Rj-a = 30°C/W 60 Rj-a = 40°C/W 40 Rj-a = 50°C/W 20 Rj-a = 60°C/W 0 0 25 50 75 100 125 150 Ambient Temperature (ºC) TYPICAL SPATIAL DISTRIBUTION 120 Relative Luminous Intensity (%) 100 80 60 40 20 0 -90 -70 -50 -30 -10 10 30 50 70 90 Angle (º) Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 5 XLAMP ML-B LEDS REFLOW SOLDERING CHARACTERISTICS In testing, Cree has found XLamp ML-B LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. Profile Feature Lead-Based Solder Lead-Free Solder 3°C/second max. 3°C/second max. Preheat: Temperature Min (Tsmin) 100°C 150°C Preheat: Temperature Max (Tsmax) 150°C 200°C 60-120 seconds 60-180 seconds 183°C 217°C 60-150 seconds 60-150 seconds 215°C 260°C 10-30 seconds 20-40 seconds 6°C/second max. 6°C/second max 6 minutes max. 8 minutes max. Average Ramp-Up Rate (Tsmax to Tp) Preheat: Time (tsmin to tsmax) Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) Peak/Classification Temperature (Tp) Time Within 5°C of Actual Peak Temperature (tp) Ramp-Down Rate Time 25°C to Peak Temperature Note: All temperatures refer to topside of the package, measured on the package body surface. Note: While the high reflow temperatures (above) have been approved, Cree’s best practice guideline for reflow is to use as low a temperature as possible during the reflow soldering process for these LEDs. Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 6 XLAMP ML-B LEDS NOTES Lumen Maintenance Projections Cree currently recommends a maximum drive current of 80 mA for XLamp ML-B white in designs seeking the ENERGY STAR* 35,000 hour lifetime rating (≥ 94.1% luminous flux @ 6000 hours) or 25,000-hour lifetime rating (≥ 91.8% luminous flux @ 6000 hours). Please read the XLamp Long-Term Lumen Maintenance application note for more details on Cree’s lumen maintenance testing and forecasting. Please read the XLamp Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. * These lifetime ratings are based on the current ENERGY STAR Solid State Lighting Luminaires V1.1 (December 12, 2008) and ENERGY STAR Integral LED Lamps V1.0 (December 3, 2009) lumen maintenance criteria. Moisture Sensitivity In testing, Cree has found XLamp ML-B LEDs to have unlimited floor life in conditions ≤30ºC / 85% relative humidity (RH). Moisture testing included a 168 hour soak at 85ºC / 85% RH followed by 3 reflow cycles, with visual and electrical inspections at each stage. RoHS Compliance The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or otherwise restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2002/95/ EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS), as amended through April 21, 2006. Vision Advisory Claim Users should be cautioned not to stare at the light of this LED product. The bright light can damage the eye. Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 7 XLAMP ML-B LEDS MECHANICAL DIMENSIONS (TA = 25°C) MX3535 Pad Layout are ±.13 mm unless otherwise indicated. All measurements Top View Top View Side View Bottom View Recommended FR4 Solder Pad Recommended MCPCB Solder Pad Alternative Solder Pad Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 8 1.5±.1 4.0±.1 XLAMP ML-B LEDS 8.0±.1 1.75±.10 2.5±.1 Cathode Side TAPE AND REEL +.3 12.0 .0 All dimensions in mm. Anode Side User Feed Direction (denoted by + and circle) END START User Feed Direction END START Trailer 160mm (min) of empty pockets sealed with tape (20 pockets min.) Loaded Pockets (1,000 Lamps) Leader 400mm (min) of empty pockets with at least 100mm sealed by tape (50 empty pockets min.) User Feed Direction Cover Tape Pocket Tape 13mm 7" Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 9 XLAMP ML-B LEDS PACKAGING All dimensions in mm. Vacuum-Sealed Vacuum-Sealed Moisture Barrier Bag Moisture Barrier Bag Label CREE Binwith Code Cree Bin & Barcode LabelLot # Code, Qty, Label with Cree Bin Label with Customer P/N, Qty,Qty, Lot #, Lot PO # # Code, Patent Label Label with Customer Order Code, Qty, Reel ID, PO # Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 10