DATA SHEET GBJ8A~GBJ8K GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER VOLTAGE 50 to 800 Volts CURRENT 8.0 Ampere GBJ Unit: inch (mm) Recongnized File #E228882 FEATURES .996(25.3) C .118(3.0) • Reliable low cost construction utilizing molded plastic technique .709(18.0) .669(17.0) .146(3.7) .129(3.3) 260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension • Both normal and Pb free product are available : Normal : 80~95% Sn, 5~20% Pb Pb free: 98.5% Sn above .087(2.2) .070(1.8) MECHANICALDATA .044(1.1) .035(0.9) Case: Reliable low cost construction utilizing molded plastic technique .304(7.7) .288(7.3) Terminals: Leads solderable per MIL-STD-202, .133(3.4) .603(15.3) .578(14.7) • High temperature soldering guaranteed: .150(3.8) Method 208 .304(7.7) .288(7.3) .304(7.7) .288(7.3) .382(9.7) .366(9.3) • Ideal for printed circuit board .189(4.8) .173(4.4) .972(24.7) .142(3.6) .122(3.1) • Plastic material has Underwriters Laboratory, Flammability Classification 94V-O .115(2.9) .098(2.5) .032(0.8) .024(0.6) Mounting position: Any Mounting torque: 5 in. lb. Max. Weight: 0.15 ounce, 4.0 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz. For Capacitive load derate current by 20%. PA RA M E TE R S YM B O L GB J 8 A GB J 8 B GB J 8 D G B J 8 G G B J 8 J G B J 8 K U N IT S M a xi m um R e c ur r e nt P e a k R e ve r s e V o l t a g e V RRM 50 100 200 400 600 800 V M a x i m u m R M S B r i d g e In p u t V o l t a g e V RMS 35 70 140 280 420 560 V V DC 50 100 200 400 600 800 V M a xi m um D C B l o c k i ng V o l t a g e M a xi m um A ve r a g e F o r w a r d T C = 1 0 0 OC R e c t i f i e d O ut p ut C ur r e nt a t T A = 4 0 OC IAV 8 .0 6 .0 A I2 t R a t i n g f o r f u s i n g ( t < 8 . 3 m s ) I2 t 166 A 2s e c IF S M 200 Apk M a x i m u m In s t a n t a n e o u s F o r w a r d V o l t a g e D r o p p e r e l e m e n t a t 4 .0 A VF 1 .0 Vpk M a xi m um R e ve r s e L e a k a g e C ur r e nt a t R a t e d @ T A = 2 5 OC D c B l o c k i ng V o l t a g e @ T A = 1 0 0 OC IR 5 .0 500 uA Rθ J A Rθ J C 8 .6 3 .1 T J ,T S TG -5 5 to + 1 5 0 P e a k F o r w a r d S ur g e C ur r e nt s i ng l e s i ne - w a ve s up e r i m p o s e d o n r a t e d l o a d ( J E D E C m e t ho d ) Ty p i c a l T h e r m a l R e s i s t a n c e p e r l e g ( N o t e 2 ) (No te 3 ) O p e r a t i n g J u n c t i o n a n d S t o r a g e Te m p e r a t u r e R a n g e O C /W O C NOTES: 1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw. 2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads. 3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate. STAD-APR.28.2004 PAGE . 1 6.0 HEAT-SINK MOUNTING, T C (4 x 4 x 0.15cm)THK COPPER PLATE 4.0 2.0 MOUNTED ON PC BOARD, TA 0.5 (12.7mm)LEAD LENGTH 60Hz RESISTIVE OR INDUCTIVE LOAD 0 0 50 100 150 TEMPERATURE, OC REVERSE CURRENT,uA 4 10 3 O 10 T J =150 C 2 10 1 10 0 O T J =25 C 10 10 -1 -2 0 10 20 30 40 50 60 70 80 90 100 110 PERCENT OF PEAK REVERE VOLTAGE,% Fig.3 - TYPICAL REVERSE CHARACTERISTICS STAD-APR.28.2004 200 160 120 80 40 0 1 6 2 10 20 40 60 100 NO. OF CYCLES AT 60Hz Fig.1 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT 10 FORWARD SURGE CURRENT, AMPERES pk (HALF SINE-WAVE) 8.0 Fig.2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT INSTANTANEOUS FORWARD CURRENT, AMPERES AVERAGE FORWARD CURRENT AMPERES RATING AND CHARACTERISTIC CURVES 100 40 20 10 4.0 2.0 1.0 O TJ=25 C Pulse Width = 300us 1% DULY Cycle 0.4 0.2 0.1 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 INSTANTANEOUS FORWARD VOLTAGE, VOLTS Fig.4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER ELEMENT PAGE . 2