LINER LTC6102 Precision zero drift current sense amplifier Datasheet

LTC6102
LTC6102-1/LTC6102HV
Precision Zero Drift
Current Sense Amplifier
Description
Features
n
n
n
n
n
n
n
n
n
n
n
Supply Range:
4V to 60V, 70V Maximum (LTC6102)
5V to 100V, 105V Maximum (LTC6102HV)
±10µV Input Offset Maximum
±50nV/°C Input Offset Drift Maximum
Fast Response: 1µs Step Response
Gain Configurable with Two Resistors
Low Input Bias Current: 3nA Maximum
PSRR 130dB Minimum
Output Currents up to 1mA
Operating Temperature Range: –40°C to 125°C
Disable Mode (LTC6102-1 Only): 1µA Maximum
Available in 8-Lead MSOP and 3mm × 3mm
DFN Packages
The LTC®6102/LTC6102HV are versatile, high voltage, highside current sense amplifiers. Their high supply voltage
rating allows their use in many high side applications,
while the low drift and offset ensure accuracy across a
wide range of operating conditions. The LTC6102-1 is a
version of the LTC6102 that includes a low power disable
mode to conserve system standby power.
The LTC6102/LTC6102HV monitor current via the voltage
across an external sense resistor (shunt resistor). Internal
circuitry converts input voltage to output current, allowing
a small sense signal on a large common mode voltage to
be translated to a ground-referred signal. Low DC offset
allows the use of very low shunt resistor values and large
gain-setting resistors. As a result, power loss in the shunt
is reduced.
Applications
n
n
n
n
n
n
The wide operating supply and high accuracy make the
LTC6102 ideal for a large array of applications, from automotive, to industrial and power management. A maximum
input sense voltage of 2V allows a wide range of currents
and voltages to be monitored. Fast response makes the
LTC6102 the perfect choice for load current warnings and
shutoff protection control.
Current Shunt Measurement
Battery Monitoring
Remote Sensing
Load Protection
Motor Control
Automotive Controls
All versions of the LTC6102 are available in 8-lead MSOP
and 3mm × 3mm DFN packages.
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
Typical Application
10A Current Sense with 10mA Resolution and 100mW
Maximum Dissipation
+
110
RIN
20Ω
–
100
+IN
–INS
+
105V
L
O
A
D
V–
–
V+
0.1µF
VREG
LTC6102
RSENSE = 100mΩ
Max VSENSE = 1V
90
–INF
1µF
5V
80
70 RSENSE = 10mΩ
Max VSENSE = 100µV
60
50
40
VOUT
OUT
DYNAMIC RANGE (dB)
VSENSE
1mΩ
+
5V TO
Dynamic Current
Measurement Range
DYNAMIC RANGE RELATIVE
TO 10µV OFFSET VOLTAGE
30
ROUT
4.99k
LTC2433-1
TO µP
20
0.0001
0.001
0.01
0.1
MAXIMUM SENSE VOLTAGE (V)
1
6102 TA01b
6102 TA01
VOUT =
ROUT
• VSENSE = 249.5VSENSE
RIN
*PROPER SHUNT SELECTION COULD ALLOW
MONITORING OF CURRENTS IN EXCESS OF 1000A
6102fe
For more information www.linear.com/LTC6102
1
LTC6102
LTC6102-1/LTC6102HV
Absolute Maximum Ratings (Note 1)
Total Supply Voltage (V+ to V–):
LTC6102/LTC6102-1..............................................70V
LTC6102HV..........................................................105V
Input Voltage Range
–INF, –INS................................. (V+ – 4V to V+ + 0.3V)
+IN............................................. (V+ – 20V to V+ + 1V)
EN............................................. (V– – 0.3V to V– + 9V)
Differential (–INS – +IN), 1 Second.......................60V
Output Voltage Range
LTC6102/LTC6102HV................ (V– – 0.3V to V– + 9V)
LTC6102-1.............................. (V– – 0.3V to V– + 15V)
Input Current
–INF, –INS.........................................................±10mA
+IN....................................................................–10mA
EN.....................................................................±10mA
Output Current........................................(–1mA, +10mA)
Output Short Circuit Duration........................... Indefinite
Operating Temperature Range: (Note 2)
LTC6102C/LTC6102C-1/LTC6102HVC... –40°C to 85°C
LTC6102I/LTC6102I-1/LTC6102HVI....... –40°C to 85°C
LTC6102H/LTC6102H-1
LTC6102HVH...................................... –40°C to 125°C
Specified Temperature Range: (Note 2)
LTC6102C/LTC6102C-1/LTC6102HVC....... 0°C to 70°C
LTC6102I/LTC6102I-1/LTC6102HVI....... –40°C to 85°C
LTC6102H/LTC6102H-1
LTC6102HVH...................................... –40°C to 125°C
Storage Temperature Range.................... –65°C to 150°C
Pin Configuration
TOP VIEW
–INS 1
–INF 2
V–/EN*
3
OUT 4
TOP VIEW
8 +IN
9
7
–INS
–INF
V–/EN*
OUT
V+
6 VREG
5 V–
1
2
3
4
8
7
6
5
+IN
V+
VREG
V–
MS8 PACKAGE
8-LEAD PLASTIC MSOP
DD PACKAGE
8-LEAD (3mm × 3mm) PLASTIC DFN
TJMAX = 150°C, θJA = 43°C/W
EXPOSED PAD (PIN 9) IS V–, MUST BE SOLDERED TO PCB
*V– FOR THE LTC6102/LTC6102HV, EN FOR THE LTC6102-1
TJMAX = 150°C, θJA = 200°C/W
*V– FOR THE LTC6102/LTC6102HV, EN FOR THE LTC6102-1
order information
LEAD FREE FINISH
LTC6102CDD#PBF
LTC6102IDD#PBF
LTC6102HDD#PBF
LTC6102CDD-1#PBF
LTC6102IDD-1#PBF
LTC6102HDD-1#PBF
LTC6102HVCDD#PBF
LTC6102HVIDD#PBF
LTC6102HVHDD#PBF
LTC6102CMS8#PBF
LTC6102IMS8#PBF
2
TAPE AND REEL
LTC6102CDD#TRPBF
LTC6102IDD#TRPBF
LTC6102HDD#TRPBF
LTC6102CDD-1#TRPBF
LTC6102IDD-1#TRPBF
LTC6102HDD-1#TRPBF
LTC6102HVCDD#TRPBF
LTC6102HVIDD#TRPBF
LTC6102HVHDD#TRPBF
LTC6102CMS8#TRPBF
LTC6102IMS8#TRPBF
PART MARKING*
LCKH
LCKH
LCKH
LDYB
LDYB
LDYB
LCVC
LCVC
LCVC
LTCKJ
LTCKJ
PACKAGE DESCRIPTION
8-Lead (3mm × 3mm) Plastic DFN
8-Lead (3mm × 3mm) Plastic DFN
8-Lead (3mm × 3mm) Plastic DFN
8-Lead (3mm × 3mm) Plastic DFN
8-Lead (3mm × 3mm) Plastic DFN
8-Lead (3mm × 3mm) Plastic DFN
8-Lead (3mm × 3mm) Plastic DFN
8-Lead (3mm × 3mm) Plastic DFN
8-Lead (3mm × 3mm) Plastic DFN
8-Lead Plastic MSOP
8-Lead Plastic MSOP
SPECIFIED TEMPERATURE RANGE
0°C to 70°C
–40°C to 85°C
–40°C to 125°C
0°C to 70°C
–40°C to 85°C
–40°C to 125°C
0°C to 70°C
–40°C to 85°C
–40°C to 125°C
0°C to 70°C
–40°C to 85°C
6102fe
For more information www.linear.com/LTC6102
LTC6102
LTC6102-1/LTC6102HV
order information
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
SPECIFIED TEMPERATURE RANGE
LTC6102HMS8#PBF
LTC6102HMS8#TRPBF
LTCKJ
8-Lead Plastic MSOP
–40°C to 125°C
LTC6102CMS8-1#PBF
LTC6102CMS8-1#TRPBF LTDXZ
8-Lead Plastic MSOP
0°C to 70°C
LTC6102IMS8-1#PBF
LTC6102IMS8-1#TRPBF LTDXZ
8-Lead Plastic MSOP
–40°C to 85°C
LTC6102HMS8-1#PBF
LTC6102HMS8-1#TRPBF LTDXZ
8-Lead Plastic MSOP
–40°C to 125°C
LTC6102HVCMS8#PBF
LTC6102HVCMS8#TRPBF LTCVB
8-Lead Plastic MSOP
0°C to 70°C
LTC6102HVIMS8#PBF
LTC6102HVIMS8#TRPBF LTCVB
8-Lead Plastic MSOP
–40°C to 85°C
LTC6102HVHMS8#PBF
LTC6102HVHMS8#TRPBF LTCVB
8-Lead Plastic MSOP
–40°C to 125°C
LEAD BASED FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
SPECIFIED TEMPERATURE RANGE
LTC6102CDD
LTC6102CDD#TR
LCKH
8-Lead (3mm × 3mm) Plastic DFN
0°C to 70°C
LTC6102IDD
LTC6102IDD#TR
LCKH
8-Lead (3mm × 3mm) Plastic DFN
–40°C to 85°C
LTC6102HDD
LTC6102HDD#TR
LCKH
8-Lead (3mm × 3mm) Plastic DFN
–40°C to 125°C
LTC6102CDD-1
LTC6102CDD-1#TR
LDYB
8-Lead (3mm × 3mm) Plastic DFN
0°C to 70°C
LTC6102IDD-1
LTC6102IDD-1#TR
LDYB
8-Lead (3mm × 3mm) Plastic DFN
–40°C to 85°C
LTC6102HDD-1
LTC6102HDD-1#TR
LDYB
8-Lead (3mm × 3mm) Plastic DFN
–40°C to 125°C
LTC6102HVCDD
LTC6102HVCDD#TR
LCVC
8-Lead (3mm × 3mm) Plastic DFN
0°C to 70°C
LTC6102HVIDD
LTC6102HVIDD#TR
LCVC
8-Lead (3mm × 3mm) Plastic DFN
–40°C to 85°C
LTC6102HVHDD
LTC6102HVHDD#TR
LCVC
8-Lead (3mm × 3mm) Plastic DFN
–40°C to 125°C
LTC6102CMS8
LTC6102CMS8#TR
LTCKJ
8-Lead Plastic MSOP
0°C to 70°C
LTC6102IMS8
LTC6102IMS8#TR
LTCKJ
8-Lead Plastic MSOP
–40°C to 85°C
LTC6102HMS8
LTC6102HMS8#TR
LTCKJ
8-Lead Plastic MSOP
–40°C to 125°C
LTC6102CMS8-1
LTC6102CMS8-1#TR
LTDXZ
8-Lead Plastic MSOP
0°C to 70°C
LTC6102IMS8-1
LTC6102IMS8-1#TR
LTDXZ
8-Lead Plastic MSOP
–40°C to 85°C
LTC6102HMS8-1
LTC6102HMS8-1#TR
LTDXZ
8-Lead Plastic MSOP
–40°C to 125°C
LTC6102HVCMS8
LTC6102HVCMS8#TR
LTCVB
8-Lead Plastic MSOP
0°C to 70°C
LTC6102HVIMS8
LTC6102HVIMS8#TR
LTCVB
8-Lead Plastic MSOP
–40°C to 85°C
LTC6102HVHMS8
LTC6102HVHMS8#TR
LTCVB
8-Lead Plastic MSOP
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
6102fe
For more information www.linear.com/LTC6102
3
LTC6102
LTC6102-1/LTC6102HV
electrical characteristics
(LTC6102, LTC6102-1) The l denotes the specifications which apply over
the full operating temperature range, otherwise specifications are at TA = 25°C. RIN = 10Ω, ROUT = 10k, VSENSE+ = V+ (see Figure 1 for
details), V+ = 12V, V– = 0V, VEN = 2.2V unless otherwise noted.
SYMBOL
V+
VOS
PARAMETER
Supply Voltage Range
Input Offset Voltage
(Note 3)
Input Offset Voltage
(Note 4)
ΔVOS/ΔT
Input Offset Voltage Drift
(Note 3)
IB
Input Bias Current (Note 5)
PSRR
Power Supply Rejection Ratio
CONDITIONS
VSENSE = 100µV
6V ≤ V+ ≤ 60V
V+ = 4V
VSENSE = 100µV
6V ≤ V+ ≤ 60V
V+ = 4V
VSENSE = 100µV
LTC6102C, LTC6102I, LTC6102C-1, LTC6102I-1
LTC6102H, LTC6102H-1
RIN = 40k, VSENSE = 2mV
LTC6102C, LTC6102I, LTC6102C-1, LTC6102I-1
LTC6102H, LTC6102H-1
VSENSE = 100µV, V+ = 6V to 60V
MIN
4
l
l
VOUT
Maximum Output Voltage
(LTC6102)
Maximum Output Voltage
(LTC6102-1)
IOUT
Maximum Output Current
tr
Input Step Response (to 2.5V on ΔVSENSE = 100mV Transient, 6V ≤ V+ ≤ 60V, RIN = 100Ω,
a 5V Output Step)
ROUT = 4.99k, IOUT = 100µA
V+ = 4V
Signal Bandwidth
IOUT = 200µA, RIN = 100Ω, ROUT = 4.99k
IOUT = 1mA, RIN = 100Ω, ROUT = 4.99k
Input Noise Voltage
0.1Hz to 10Hz
Supply Current
V+ = 4V, IOUT = 0, RIN = 10k, ROUT = 100k
BW
eN
IS
3
5
10
25
µV
µV
3
5
35
50
µV
µV
25
25
60
50
75
nV/°C
nV/°C
pA
nA
nA
dB
dB
dB
dB
l
l
l
2
0.8
V
V
l
l
l
8
3
1
V
V
V
l
l
l
14
11.7
3.8
1
0.5
l
l
150
140
1.5
140
200
2
275
V+ = 6V, IOUT = 0, RIN = 10k, ROUT = 100k
290
l
V+ = 12V, IOUT = 0, RIN = 10k, ROUT = 100k
300
l
IDIS
VENL
4
Supply Current in Disable Mode
(LTC6102-1 Only)
Enable Input Voltage Low
(LTC6102-1 Only)
V
V
V
mA
mA
µs
1
l
V+ = 60V, IOUT = 0, RIN = 10k, ROUT = 100k
LTC6102C, LTC6102I, LTC6102C-1, LTC6102I-1
LTC6102H, LTC6102H-1
VEN = 0.8V, V+ = 12V
VEN = 0.8V, V+ = 60V
3
20
UNITS
V
130
125
120
115
VSENSE = 100µV, V+ = 4V to 60V
Error <1%, RIN = 10k, ROUT = 10k
6V ≤ V+ ≤ 60V
V+ = 4V
VSENSE = 2mV, ROUT = 100k
12V ≤ V+ ≤ 60V
V+ = 6V
V+ = 4V
VSENSE = 2mV, ROUT = 100k
V+ = 60V
V+ = 12V
V+ = 4V
6V ≤ V+ ≤ 60V, RIN = 1k, ROUT = 1k, VSENSE = 1.1V
V+ = 4V, RIN = 10Ω, ROUT = 1k, VSENSE = 11mV
MAX
60
l
l
l
VSENSE(MAX) Input Sense Voltage Full Scale
(V+ – VIN+)
TYP
420
l
l
l
l
l
400
475
425
500
450
525
575
650
675
1
18
0.8
µs
kHz
kHz
µVP-P
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
V
6102fe
For more information www.linear.com/LTC6102
LTC6102
LTC6102-1/LTC6102HV
Electrical Characteristics
(LTC6102, LTC6102-1) The l denotes the specifications which apply over
the full operating temperature range, otherwise specifications are at TA = 25°C. RIN = 10Ω, ROUT = 10k, VSENSE+ = V+ (see Figure 1 for
details), V+ = 12V, V– = 0V, VEN = 2.2V unless otherwise noted.
SYMBOL
VENH
tON
PARAMETER
Enable Input Voltage High
(LTC6102-1 Only)
Enable Input Pin Current
(LTC6102-1 Only)
Turn-On Time (LTC6102-1 Only)
tOFF
Turn-Off Time (LTC6102-1 Only)
fS
Sampling Frequency
IBEN
CONDITIONS
l
VEN = 0V to 9V
MIN
2.2
TYP
MAX
8
l
VEN = 2.2V, VSENSE = 1mV, Output Settles to Within 1% of
Final Value
VEN = 0.8V, VSENSE = 1mV, Supply Current Drops to Less
Than 10% of Nominal Value
UNITS
V
µA
500
µs
100
µs
10
kHz
Electrical Characteristics
(LTC6102HV) The l denotes the specifications which apply over the full
operating temperature range, otherwise specifications are at TA = 25°C. RIN = 10Ω, ROUT = 10k, VSENSE+ = V+ (see Figure 1 for details),
V+ = 12V, V– = 0V unless otherwise noted.
SYMBOL
PARAMETER
V+
Supply Voltage Range
CONDITIONS
VOS
Input Offset Voltage
(Note 3)
VSENSE = 100µV
6V ≤ V+ ≤ 100V
V+ = 5V
Input Offset Voltage
(Note 4)
VSENSE = 100µV
6V ≤ V+ ≤ 100V
V+ = 5V
Input Offset Voltage Drift (Note 3) VSENSE = 100µV
LTC6102HVC, LTC6102HVI
LTC6102HVH
IB
Input Bias Current (Note 5)
Power Supply Rejection Ratio
TYP
MAX
UNITS
100
V
3
5
10
25
µV
µV
3
5
35
50
µV
µV
25
25
50
75
nV/°C
nV/°C
3
20
pA
nA
nA
5
ΔVOS/ΔT
PSRR
MIN
RIN = 40k, VSENSE = 2mV
LTC6102HVC, LTC6102HVI
LTC6102HVH
l
l
60
l
l
VSENSE = 100µV, V+ = 6V to 100V
l
130
125
l
120
115
VSENSE = 100µV, V+ = 5V to 100V
150
140
dB
dB
dB
dB
VSENSE(MAX) Input Sense Voltage Full Scale
(V+ – V+IN)
Error <1%, RIN = 10k, ROUT = 10k
6V ≤ V+ ≤ 100V
V+ = 5V
l
l
2
1
V
V
VOUT
VSENSE = 2mV, ROUT = 100k
12V ≤ V+ ≤ 100V
V+ = 5V
l
l
8
3
V
V
6V ≤ V+ ≤ 100V, RIN = 1k, ROUT = 1k, VSENSE = 1.1V
V+ = 5V, RIN = 10Ω, ROUT = 1k, VSENSE = 11mV
l
l
1
0.5
Maximum Output Voltage
IOUT
Maximum Output Current
tr
Input Step Response (to 2.5V on a ΔVSENSE = 100mV Transient, 6V ≤ V+ ≤ 100V,
5V Output Step)
RIN = 100Ω, ROUT = 4.99k, IOUT = 100µA
1
µs
V+ = 5V
1.5
µs
140
200
kHz
kHz
BW
Signal Bandwidth
IOUT = 200µA, RIN = 100Ω, ROUT = 4.99k
IOUT = 1mA, RIN = 100Ω, ROUT = 4.99k
eN
Input Noise Voltage
0.1Hz to 10Hz
mA
mA
2
µVP-P
6102fe
For more information www.linear.com/LTC6102
5
LTC6102
LTC6102-1/LTC6102HV
Electrical Characteristics
(LTC6102HV) The l denotes the specifications which apply over the full
operating temperature range, otherwise specifications are at TA = 25°C. RIN = 10Ω, ROUT = 10k, VSENSE+ = V+ (see Figure 1 for details),
V+ = 12V, V– = 0V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
IS
Supply Current
V+ = 5V, IOUT = 0, RIN = 10k, ROUT = 100k
MIN
TYP
MAX
UNITS
275
400
475
µA
µA
280
425
500
µA
µA
290
450
525
µA
µA
l
V+ = 6V, IOUT = 0, RIN = 10k, ROUT = 100k
l
V+ = 12V, IOUT = 0, RIN = 10k, ROUT = 100k
l
V+ = 100V, IOUT = 0, RIN = 10k, ROUT = 100k
fS
575
µA
LTC6102HVC, LTC6102HVI
l
650
µA
LTC6102HVH
l
675
µA
Sampling Frequency
10
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime. In addition to the Absolute Maximum Ratings, the
output current of the LTC6102 must be limited to ensure that the power
dissipation in the LTC6102 does not allow the die temperature to exceed
150°C. See the Applications Information “Output Current Limitations Due
to Power Dissipation” for further information.
Note 2: The LTC6102C/LTC6102C-1/LTC6102HVC are guaranteed to meet
specified performance from 0°C to 70°C. The LTC6102C/LTC6102C-1/
LTC6102HVC are designed, characterized and expected to meet specified
performance from –40°C to 85°C but are not tested or QA sampled at
these temperatures. LTC6102I/LTC6102I-1/LTC6102HVI are guaranteed
6
420
kHz
to meet specified performance from –40°C to 85°C. The LTC6102H/
LTC6102H-1/LTC6102HVH are guaranteed to meet specified performance
from –40°C to 125°C.
Note 3: These Parameters are guaranteed by design and are not 100%
tested. Thermocouple effects preclude measurements of these voltage
levels during automated testing.
Note 4: Limits are fully tested. Limit is determined by high speed
automated test capability.
Note 5: IB specification is limited by practical automated test resolution.
Please refer to the Typical Performance Characteristics section for
more information regarding actual typical performance. For tighter
specifications, please contact LTC Marketing.
6102fe
For more information www.linear.com/LTC6102
LTC6102
LTC6102-1/LTC6102HV
Typical Performance Characteristics
Input VOS vs Temperature
Input VOS vs Supply Voltage
15
10
10
VS = 4V
5
0
VS = 12V
–5
5
0
–5
TA = –40°C
TA = 0°C
TA = 25°C
TA = 70°C
TA = 85°C
TA = 125°C
–15
0
–20
20 40 60 80 100 120
TEMPERATURE (°C)
6102 G01
0
4 8 12 16 20 24 28 32 36 40 44 48 52 56 60
SUPPLY VOLTAGE (V)
MAXIMUM VOUT (V)
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
–40
6102 G04
VS = 100V
VS = 12V
VS = 6V
VS = 5V
–20
0
20 40 60 80 100 120
TEMPERATURE (°C)
6.5
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
–40
35
VS = 12V
30
IOUT = 200μA DC
0
6102 G07
6102 G03
VS = 6V
VS = 5V
VS = 4V
–20
10000
5
TA = 25°C
V+ = 12V
–5 RIN = 100Ω
ROUT = 4.99k
–10
1k
10k
120
VS = 60V
IOUT = 1mA DC
BIAS CURRENT (pA)
GAIN (dB)
10
100
0
20 40 60 80 100 120
TEMPERATURE (°C)
Input Bias Current vs Temperature
20
15
60
80
VSUPPLY (V)
VS = 12V
100000
25
VS = 100V
20 40 60 80 100 120
TEMPERATURE (°C)
40
6102 G06
Gain vs Frequency
VS = 5V
20
LTC6102/LTC6102-1: IOUT
Maximum vs Temperature
40
VS = 6V
0
6102 G05
LTC6102HV: IOUT Maximum vs
Temperature
0
1.0
LTC6102HV: VOUT Maximum vs
Temperature
15
14
13
VS = 60V
12
11
V
S = 12V
10
9
8
7
VS = 6V
6
5
4
VS = 4V
3
2
VS = 5V
1
0
–40 –20 0 20 40 60 80 100 120
TEMPERATURE (°C)
–20
1.5
6102 G02
LTC6102: VOUT Maximum vs
Temperature
6.5
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
–40
2.0
0.5
MAXIMUM IOUT (mA)
–20
–40 –20
TA = 25°C
2.5
–10
–15
MAXIMUM VOUT (V)
3.0
MAXIMUM VSENSE (V)
15
–10
MAXIMUM IOUT (mA)
Input Sense Range
20
INPUT OFFSET (μV)
INPUT OFFSET (μV)
20
100k
1M
FREQUENCY (Hz)
10M
6102 G09
VS = 100V
VS = 60V
VS = 12V
VS = 6V
VS = 5V
1000
100
10
–40 –20
0
20 40 60 80
TEMPERATURE (°C)
100 120
6102 G10
6102fe
For more information www.linear.com/LTC6102
7
LTC6102
LTC6102-1/LTC6102HV
Typical Performance Characteristics
LTC6102: Supply Current vs
Supply Voltage
LTC6102HV: Supply Current vs
Supply Voltage
600
600
500
SUPPLY CURRENT (μA)
400
300
TA = 25°C
200
TA = 0°C
TA = –40°C
100
0
TA = 70°C
500
TA = 125°C
V+ – 10mV
TA = 125°C
400
0.5V
300
200
0
0 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60
SUPPLY VOLTAGE (V)
TA = –40°C
TA = 0°C
VIN = 0
RIN = 2M
0
TIME (10μs/DIV)
Step Response 100mV
V+
VSENSE–
V+ – 20mV
V+ – 100mV
1V
5V
TA = 25°C
V+ = 12V
RIN = 100Ω
ROUT = 4.99k
VSENSE+ = V+
VSENSE– = 100mV
5.5V
5V
CLOAD = 10pF
0V
TA = 25°C
V+ = 12V
RIN = 100Ω
ROUT = 4.99k
VSENSE+ = V+
0.5V
0V
Input Referred Noise
0.1Hz to 10Hz
PSRR vs Frequency
5
IOUT = 100μA
0.5V
0V
TIME (500ns/DIV)
8
3
2
NOISE (μV)
PSRR (dB)
120
100
80
60
IOUT = 0
40
V+ = 12V
RIN = 100Ω
ROUT = 4.99k
AV = 49.9
IOUT = 500μA
20
0.1
6102 G18
TA = 25°C
V+ = 12V
RIN = 10Ω
ROUT = 1k
VSENSE = 2mV
4
140
TA = 25°C
V+ = 12V
RIN = 100Ω
ROUT = 4.99k
VSENSE+ = V+
1
10
6102 G17
6102 G15
160
VOUT
IOUT = 100μA
VOUT
TIME (500ns/DIV)
TIME (10μs/DIV)
VSENSE– = 100mV
TA = 25°C
V+ = 12V
RIN = 100Ω
ROUT = 4.99k
VSENSE+ = V+
IOUT = 0
VOUT
6102 G14
Step Response Falling Edge
5.5V
5V
6102 G13
Step Response Rising Edge
VSENSE–
CLOAD = 1000pF
VOUT
TIME (10μs/DIV)
VOUT
6102 G12
Step Response 10mV to 20mV
0.5V
0V
8 16 24 32 40 48 56 64 72 80 88 96
SUPPLY VOLTAGE (V)
6102 G11
V+ – 10mV
TA = 25°C
V+ = 12V
RIN = 100Ω
ROUT = 4.99k
VSENSE+ = V+
TA = 25°C
100
VIN = 0
RIN = 2M
VSENSE–
V+
TA = 85°C
TA = 70°C
SUPPLY CURRENT (μA)
TA = 85°C
Step Response 0mV to 10mV
1
0
–1
–2
–3
–4
100 1k
10k
FREQUENCY (Hz)
100k
1M
6102 G19
–5
0
1
2
3
4 5 6
TIME (s)
7
8
9
10
6102 G20
6102fe
For more information www.linear.com/LTC6102
LTC6102
LTC6102-1/LTC6102HV
Typical Performance Characteristics
LTC6102-1: Supply Current vs
Supply Voltage
600
GAIN = 10
SUPPLY CURRENT (µA)
100
18
VEN = 2V
VSENSE = –0.1V
500
TA = 125°C
400
14
TA = 85°C
300
TA = 25°C
200
TA = –40°C
100
1k
10k
100k
FREQUENCY (Hz)
1M
–100
12
TA = 25°C
10
8
6
TA = –40°C
4
2
0
10
6102 G21
40
30
50
20
VOLTAGE SUPPLY (V)
60
–2
70
LTC6102-1: Supply Current vs
Enable Voltage
0
10
30
40
50
20
SUPPLY VOLTAGE (V)
6
V+ = 60V
ENABLE PIN CURRENT (µA)
V+ = 12V
250
200
150
TURN OFF (12V)
100
50
6102 G23
–50
1
0
2
3 4 5 6 7
ENABLE VOLTAGE (V)
8
9
4
3
2
1
0
TA = 25°C
VSENSE = 0V
0
–1
10
0
1
3
7 8
4 5 6
ENABLE VOLTAGE (V)
2
6102 G24
6
4.0
3.5
3.0
5
VOLTAGE (V)
4
EN
2
OUT
1
2.0
1.5
1.0
EN
OUT
0.5
0
–1
–200
TA = 25°C
V+ = 12V
VSENSE = 1mV
2.5
3
10
LTC6102-1: Turn-Off Time
TA = 25°C
V+ = 12V
VSENSE = 1mV
7
9
6102 G25
LTC6102-1: Turn-On Time
8
70
TA = 25°C
V+ = 12V
5
350
300
60
LTC6102-1: Enable Pin Current vs
Enable Voltage
450
400
TA = 85°C
TA = 125°C
0
6102 G22
SUPPLY CURRENT (µA)
0
100
VEN = 0.8V
16
0
VOLTAGE (V)
VOLTAGE NOISE DENSITY (nV/√Hz)
200
LTC6102-1: Supply Current vs
Supply Voltage when Disabled
SUPPLY CURRENT (µA)
Noise Spectral Density
0
0
200
400
TIME (µs)
600
800
–0.5
–20 –15 –10 –5
6102 G26
0 5 10 15 20 25 30
TIME (µs)
6102 G27
6102fe
For more information www.linear.com/LTC6102
9
LTC6102
LTC6102-1/LTC6102HV
pin functions
–INS (Pin 1): Amplifier Inverting Input. When tied to –INF,
the internal sense amplifier will drive –INS to the same
potential as +IN.
–INF (Pin 2): Force Input. This pin carries the input
current from RIN and must be tied to –INS near RIN. A
resistor (RIN) tied from V+ to –INF sets the output current
IOUT = VSENSE/RIN. VSENSE is the voltage across the external RSENSE.
V– (Pin 3, LTC6102/LTC6102HV Only): Negative Supply.
EN (Pin 3, LTC6102-1 Only): Enable Pin, Referenced to
the Negative Supply. When the enable pin is pulled high,
the LTC6102-1 is active. When the enable pin is pulled low
or left floating, the LTC6102-1 is disabled.
OUT (Pin 4): Open-Drain Current output. OUT will source
a current that is proportional to the sense voltage into
an external resistor. IOUT is the same current that enters
–INF.
10
V– (Pin 5): Negative Supply.
VREG (Pin 6): Internal Regulated Supply. A 0.1µF (or
larger) capacitor should be tied from VREG to V+. VREG is
not designed to drive external circuits.
V+ (Pin 7): Positive Supply. Supply current is drawn
through this pin.
+IN (Pin 8): Amplifier Noninverting Input. Must be tied
to the system load end of the sense resistor. The +IN pin
has an internal 5k series resistor designed to allow large
input voltage transients or accidental disconnection of the
sense resistor. This pin can be held up to 20V below the
–INS pin indefinitely, or up to 60V below the –INS pin for
up to one second (see Absolute Maximum Ratings).
Exposed Pad (Pin 9, DFN Only): V–. The Exposed Pad
must be soldered to PCB.
6102fe
For more information www.linear.com/LTC6102
LTC6102
LTC6102-1/LTC6102HV
block diagram
VBATTERY
+
VSENSE
RSENSE
–
ILOAD
0.1µF
RIN
–INF
L
O
A
D
–INS
V+
10V
10V
5V
5V
VREG
–
5k
+IN
+
OUT
5k
IOUT
VOUT = VSENSE •
ROUT
EN* V–
*LTC6102-1 ONLY
ROUT
RIN
V–
6102 BD
VENABLE
Figure 1. Block Diagram and Typical Connection
6102fe
For more information www.linear.com/LTC6102
11
LTC6102
LTC6102-1/LTC6102HV
Applications Information
The LTC6102 high side current sense amplifier (Figure 1)
provides accurate monitoring of current through a userselected sense resistor. The sense voltage is amplified by
a user-selected gain and level shifted from the positive
power supply to a ground-referred output. The output
signal is analog and may be used as is or processed with
an output filter.
Theory of Operation
An internal sense amplifier loop forces –INS to have the
same potential as +IN. Connecting an external resistor,
RIN, between –INS and V+ forces a potential across RIN
that is the same as the sense voltage across RSENSE. A
corresponding current, VSENSE/RIN, will flow through RIN.
The high impedance inputs of the sense amplifier will not
conduct this input current, so it will flow through the –INF
pin and an internal MOSFET to the output pin.
The output current can be transformed into a voltage by
adding a resistor from OUT to V–. The output voltage is
then VO = V– + IOUT • ROUT.
Useful Gain Configurations
GAIN
RIN
ROUT
VSENSE AT VOUT = 5V
200
49.9Ω
10k
25mV
500
20Ω
10k
10mV
1000
10Ω
10k
5mV
4990
1Ω
4.99k
1mV
Selection of External Current Sense Resistor
The external sense resistor, RSENSE, has a significant effect
on the function of a current sensing system and must be
chosen with care.
First, the power dissipation in the resistor should be
considered. The system load current will cause both heat
dissipation and voltage loss in RSENSE. As a result, the sense
resistor should be as small as possible while still providing
the input dynamic range required by the measurement.
Note that input dynamic range is the difference between
the maximum input signal and the minimum accurately
reproduced signal, and is limited primarily by input DC
offset of the internal amplifier of the LTC6102. In addition,
RSENSE must be small enough that VSENSE does not exceed
12
the maximum sense voltage specified by the LTC6102 or
the sense resistor, even under peak load conditions. As
an example, an application may require that the maximum
sense voltage be 100mV. If this application is expected
to draw 20A at peak load, RSENSE should be no more
than 5mΩ.
Once the maximum RSENSE value is determined, the
minimum sense resistor value will be set by the resolution or dynamic range required. The minimum signal
that can be accurately represented by this sense amp is
limited by the input offset. As an example, the LTC6102
has a typical input offset of 3µV. If the minimum current
is 1mA, a sense resistor of 3mΩ will set VSENSE to 3µV.
This is the same value as the input offset. A larger sense
resistor will reduce the error due to offset by increasing
the sense voltage for a given load current.
For this example, choosing a 5mΩ RSENSE will maximize
the dynamic range and provide a system that has 100mV
across the sense resistor at peak load (20A), while input
offset causes an error equivalent to only 0.6mA of load
current.
Peak dissipation is 2W. If a 0.5mΩ sense resistor is employed, then the effective current error is 6mA (0.03%
of full-scale), while the peak sense voltage is reduced to
10mV at 20A, dissipating only 200mW.
The low offset and corresponding large dynamic range of
the LTC6102 make it more flexible than other solutions
in this respect. The 3µV typical offset gives 100dB of dynamic range for a sense voltage that is limited to 300mV
max, and over 116dB of dynamic range if a maximum of
2V is allowed.
The previous example assumes that a large output dynamic
range is required. For circuits that do not require large
dynamic range, the wide input range of the LTC6102 may
be used to reduce the size of the sense resistor, reducing
power loss and increasing reliability. For example, in a
100A circuit requiring 60dB of dynamic range, the input
offset and drift of most current-sense solutions will require
that the shunt be chosen so that the sense voltage is at
least 100mV at full scale so that the minimum input is
greater than 100µV. This will cause power dissipation in
excess of 10W at full scale! That much power loss can put
6102fe
For more information www.linear.com/LTC6102
LTC6102
LTC6102-1/LTC6102HV
Applications Information
a significant load on the power supply and create thermal
design headaches. In addition, heating in the sense resistor
can reduce its accuracy and reliability.
In contrast, the large dynamic range of the LTC6102 allows
the use of a much smaller sense resistor. The LTC6102
allows the minimum sense voltage to be reduced to less
than 10µV. The peak sense voltage would then be 10mV,
dissipating only 1W at 100A in a 100µΩ sense resistor!
With a specialized sense resistor, the same system would
allow peak currents of more than 1000A without exceeding
the input range of the LTC6102 or damaging the shunt.
Dynamic Range vs Maximum
Power Dissipation in RSENSE
110
100
high-current paths, this error can be reduced by orders of
magnitude. A sense resistor with integrated Kelvin sense
terminals will give the best results. Figure 2 illustrates the
recommended method. Note that the LTC6102 has a Kelvin
input structure such that current flows into –INF. The –INS
and –INF pins should be tied as close as possible to RIN.
This reduces the parasitic series resistance so that RIN
may be as low as 1Ω, allowing high gain settings to be
used with very little gain error.
V+
TIE AS CLOSE TO RIN AS POSSIBLE
RIN–
RSENSE
RIN+
+IN
RSENSE = 100mΩ RSENSE = 10mΩ
LOAD
RSENSE = 1Ω
DYNAMIC RANGE (dB)
–
V–
90
80
–INS
+
–INF
V+
100dB: MAX
VSENSE = 1V
0.1µF
VREG
70
40dB: MAX
VSENSE = 1mV
60
50
40
30
OUT
LTC6102
VOUT
ROUT
RSENSE = 10µΩ
RSENSE = 100µΩ
RSENSE = 1mΩ
20
0.001
0.01
0.1
RSENSE*
1
10
V+
100
LOAD
MAXIMUM POWER DISSIPATION (W)
DYNAMIC RANGE RELATIVE
TO 10µV, MINIMUM VSENSE
MAX ISENSE = 1A
MAX ISENSE = 10A
MAX ISENSE = 100A
RIN–
RIN+
6102 AI01
CREG
V–
OUTPUT
Sense Resistor Connection
Kelvin connection of +IN and –INS to the sense resistor
should be used in all but the lowest power applications.
Solder connections and PC board interconnections that
carry high current can cause significant error in measurement due to their relatively large resistances. One 10mm
× 10mm square trace of one-ounce copper is approximately 0.5mΩ. A 1mV error can be caused by as little
as 2A flowing through this small interconnect. This will
cause a 1% error in a 100mV signal. A 10A load current
in the same interconnect will cause a 5% error for the
same 100mV signal. An additional error is caused by the
change in copper resistance over temperature, which is in
excess of 0.4%/°C. By isolating the sense traces from the
LTC6102
ROUT
V–
*VISHAY VCS1625 SERIES
WITH 4 PAD KELVIN CONNECTION
6102 F02
Figure 2. Kelvin Input Connection Preserves Accuracy
with Large Load Current and Large Output Current
Selection of External Input Resistor, RIN
The external input resistor, RIN, controls the transconductance of the current sense circuit, IOUT = VSENSE/RIN. For
example, if RIN = 100, then IOUT = VSENSE/100 or IOUT =
1mA for VSENSE = 100mV.
RIN should be chosen to provide the required resolution
while limiting the output current. At low supply voltage,
IOUT may be as much as 1mA. By setting RIN such that
6102fe
For more information www.linear.com/LTC6102
13
LTC6102
LTC6102-1/LTC6102HV
Applications Information
the largest expected sense voltage gives IOUT = 1mA, then
the maximum output dynamic range is available. Output
dynamic range is limited by both the maximum allowed
output current (Note 1) and the maximum allowed output
voltage, as well as the minimum practical output signal. If
less dynamic range is required, then RIN can be increased
accordingly, reducing the output current and power dissipation. If small sense currents must be resolved accurately in a system that has very wide dynamic range, a
smaller RIN may be used if the max current is limited in
another way, such as with a Schottky diode across RSENSE
(Figure 3). This will reduce the high current measurement
accuracy by limiting the result, while increasing the low
current measurement resolution. This approach can be
helpful in cases where occasional large burst currents
may be ignored.
V+
RSENSE
DSENSE
6102 F03
LOAD
Figure 3. Shunt Diode Limits Maximum Input Voltage to Allow
Better Low Input Resolution Without Overranging
Care should be taken when designing the PC board layout for RIN, especially for small RIN values. All trace and
interconnect impedances will increase the effective RIN
value, causing a gain error. It is important to note that the
large temperature drift of copper resistance will cause a
change in gain over temperature if proper care is not taken
to reduce this effect.
To further limit the effect of trace resistance on gain,
maximizing the accuracy of these circuits, the LTC6102 has
been designed with a Kelvin input. The inverting terminal
(–INS) is separate from the feedback path (–INF). During
operation, these two pins must be connected together.
The design of the LTC6102 is such that current into –INS
is input bias current only, which is typically 60pA at 25°C.
Almost all of the current from RIN flows into –INF, through
14
the LTC6102, and into ROUT via the OUT pin. In order to
minimize gain error, –INS should be routed in a separate
path from –INF to a point as close to RIN as possible. In
addition, the higher potential terminal of RIN should be
connected directly to the positive terminal of RSENSE (or
any input voltage source). For the highest accuracy, RIN
should be a four-terminal resistor if it is less than 10Ω.
Selection of External Output Resistor, ROUT
The output resistor, ROUT , determines how the output current is converted to voltage. VOUT is simply IOUT • ROUT .
In choosing an output resistor, the max output voltage
must first be considered. If the circuit that is driven by the
output does not have a limited input voltage, then ROUT
must be chosen such that the max output voltage does
not exceed the LTC6102 max output voltage rating. If the
following circuit is a buffer or ADC with limited input range,
then ROUT must be chosen so that IOUT(MAX) • ROUT is less
than the allowed maximum input range of this circuit.
In addition, the output impedance is determined by ROUT. If
the circuit to be driven has high enough input impedance,
then almost any output impedance will be acceptable.
However, if the driven circuit has relatively low input impedance, or draws spikes of current, such as an ADC might
do, then a lower ROUT value may be required in order to
preserve the accuracy of the output. As an example, if the
input impedance of the driven circuit is 100 times ROUT ,
then the accuracy of VOUT will be reduced by 1% since:
VOUT = IOUT •
ROUT • RIN(DRIVEN)
ROUT + RIN(DRIVEN)
= IOUT • ROUT •
100
= 0.99 • IOUT • ROUT
101
Error Sources
The current sense system uses an amplifier and resistors
to apply gain and level shift the result. The output is then
dependent on the characteristics of the amplifier, such as
gain and input offset, as well as resistor matching.
6102fe
For more information www.linear.com/LTC6102
LTC6102
LTC6102-1/LTC6102HV
Applications Information
Ideally, the circuit output is:
VOUT = VSENSE •
ROUT
;V
= RSENSE • ISENSE
RIN SENSE
In this case, the only error is due to resistor mismatch,
which provides an error in gain only.
Output Error, EOUT, Due to the Amplifier DC Offset
Voltage, VOS
The DC offset voltage of the amplifier adds directly to
the value of the sense voltage, VSENSE. This error is very
small (3µV typ) and may be ignored for reasonable values
of RIN. See Figure 4. For very high dynamic range, this
offset can be calibrated in the system due to its extremely
low drift.
VIN = 10µV
OUTPUT ERROR (%)
10
1
Note that in applications where RSENSE ≈ RIN, IB(+) causes
a voltage offset in RSENSE that cancels the error due to
IB(–) and EOUT(IBIAS) ≈ 0. In applications where RSENSE <
RIN, the bias current error can be similarly reduced if an
external resistor RIN(+) = (RIN – RSENSE) is connected as
shown in Figure 5. Under both conditions:
EOUT(IBIAS) = ± ROUT • IOS; IOS = IB(+) – IB(–)
EOUT(VOS) = VOS • (ROUT/RIN)
100
For instance if IBIAS is 1nA and ROUT is 10k, the output
error is –10µV.
Adding RIN+ as described will maximize the dynamic
range of the circuit. For less sensitive designs, RIN+ is
not necessary.
V+
RIN–
RSENSE
RIN+
+IN
–INS
+
FOR A 500µΩ SHUNT
VIN = 100mV, ISHUNT = 200A
ERROR DUE TO VOS IS 6mA
LOAD
–
V–
–INF
V+
0.1
0.1µF
VREG
0.01
LTC6102
0.001
0.0001
0.00001 0.0001
OUT
VOUT
ROUT
0.001
0.01
INPUT VOLTAGE (V)
0.1
6102 F04
Figure 4. LTC6102 Output Error Due to Typical Input Offset
vs Input Voltage
Output Error, EOUT, Due to the Bias Currents,
IB(+) and IB(–)
The input bias current of the LTC6102 is vanishingly small.
However, for very high resolution, or at high temperatures
where IB increases due to leakage, the current may be
significant.
The bias current IB(+) flows into the positive input of the
internal op amp. IB(–) flows into the negative input.
EOUT(IBIAS) = ROUT((IB(+) • (RSENSE/RIN) – IB(–))
Since IB(+) ≈ IB(–) = IBIAS, if RSENSE << RIN then,
EOUT(IBIAS) ≈ –ROUT • IBIAS
RIN+ = RIN– – RSENSE
1
6102 F05
Figure 5. Second Input R Minimizes
Error Due to Input Bias Current
Clock Feedthrough, Input Bias Current
The LTC6102 uses auto-zeroing circuitry to achieve an
almost zero DC offset over temperature, sense voltage,
and power supply voltage. The frequency of the clock
used for auto-zeroing is typically 10kHz. The term clock
feedthrough is broadly used to indicate visibility of this
clock frequency in the op amp output spectrum. There are
typically two types of clock feedthrough in auto zeroed
amps like the LTC6102.
The first form of clock feedthrough is caused by the
settling of the internal sampling capacitor and is input
referred; that is, it is multiplied by the internal loop gain
6102fe
For more information www.linear.com/LTC6102
15
LTC6102
LTC6102-1/LTC6102HV
Applications Information
of the amp. This form of clock feedthrough is independent of the magnitude of the input source resistance or
the magnitude of the gain setting resistors. The LTC6102
has a residue clock feedthrough of less then 1µVRMS input
referred at 10kHz.
The second form of clock feedthrough is caused by the
small amount of charge injection occurring during the
sampling and holding of the amp’s input offset voltage.
The current spikes are multiplied by the impedance seen
at the input terminals of the amp, appearing at the output
multiplied by the internal loop gain of the internal op amp.
To reduce this form of clock feedthrough, use smaller
valued gain setting resistors and minimize the source
resistance at the input.
Input bias current is defined as the DC current into the
input pins of the op amp. The same current spikes that
cause the second form of clock feedthrough described
above, when averaged, dominate the DC input bias current
of the op amp below 70°C.
As temperature increases, the leakage of the ESD protection diodes on the inputs increases the input bias currents
of both inputs in the positive direction, while the current
caused by the charge injection stays relatively constant. At
temperatures above 70°C, the leakage current dominates
and both the negative and positive pins’ input bias currents
are in the positive direction (into the pins).
At maximum supply and maximum output current, the
total power dissipation can exceed 100mW. This will
cause significant heating of the LTC6102 die. In order to
prevent damage to the LTC6102, the maximum expected
dissipation in each application should be calculated. This
number can be multiplied by the θJA value listed in the
package section on page 2 to find the maximum expected
die temperature. This must not be allowed to exceed 150°C
or performance may be degraded.
As an example, if an LTC6102 in the MSOP package is to
be biased at 55V ±5V supply with 1mA output current at
80°C:
PQ(MAX) = IDD(MAX) • V+(MAX) = 39mW
POUT(MAX) = IOUT • V+(MAX) = 60mW
TRISE = θJA • PTOTAL(MAX)
TMAX = TAMBIENT + TRISE
TMAX must be < 125°C
PTOTAL(MAX) ≈ 99mW and the max die temp
will be 100°C
Output Current Limitations Due to Power Dissipation
If this same circuit must run at 125°C, the max die temp
will increase to 145°C. (Note that supply current, and
therefore PQ, is proportional to temperature. Refer to
Typical Performance Characteristics section.) Note that
the DD package has a smaller θJA than the MSOP package, which will substantially reduce the die temperature
at similar power levels.
The LTC6102 can deliver more than 1mA continuous current to the output pin. This current flows through RIN and
enters the current sense amp via the –INF pin. The power
dissipated in the LTC6102 due to the output current is:
The LTC6102HV can be used at voltages up to 105V. This
additional voltage requires that more power be dissipated
for a given level of current. This will further limit the allowed
output current at high ambient temperatures.
POUT = (V–INF – VOUT) • IOUT
Since V–INF
≈ V+, P
+
OUT ≈ (V – VOUT) • IOUT
There is also power dissipated due to the quiescent supply current:
PQ = IS • V+
It is important to note that the LTC6102 has been designed
to provide at least 1mA to the output when required, and
can deliver more depending on the conditions. Care must
be taken to limit the maximum output current by proper
choice of sense and input resistors and, if input fault
conditions are likely, an external clamp.
The total power dissipated is the output current dissipation
plus the quiescent dissipation:
PTOTAL = POUT + PQ
16
6102fe
For more information www.linear.com/LTC6102
LTC6102
LTC6102-1/LTC6102HV
Applications Information
Output Filtering
VBAT
The output voltage, VOUT, is simply IOUT • ZOUT. This
makes filtering straightforward. Any circuit may be used
which generates the required ZOUT to get the desired filter
response. For example, a capacitor in parallel with ROUT
will give a low pass response. This will reduce unwanted
noise from the output, and may also be useful as a charge
reservoir to keep the output steady while driving a switching circuit such as a mux or ADC. This output capacitor
in parallel with an output resistor will create a pole in the
output response at:
f –3dB =
RIN
RSENSE
+IN
–INS
+
LOAD
+ – 2V) TO V+
(V
–
V–
0.1µF
VREG
OUT
LTC6102
VOUT
ROUT
6102 F06
2 • π • ROUT • COUT
Figure 6. V+ Powered Separately from Load Supply (VBAT)
Useful Equations
VBAT
Input Voltage: VSENSE =ISENSE • RSENSE
Current Gain:
V+
V+
1
Voltage Gain:
–INF
VOUT ROUT
=
VSENSE RIN
IOUT
ISENSE
Transconductance:
Transimpedance:
=
RSENSE
+
LOAD
ISENSE
V–
–
–INF
V+
VREG
IOUT
1
=
VSENSE RIN
= RSENSE •
–INS
+IN
RSENSE
RIN
VOUT
RIN
LTC6102
OUT
0.1µF
VOUT
ROUT
ROUT
RIN
6102 F07
Figure 7. LTC6102 Supply Current Monitored with Load
Input Sense Range
The inputs of the LTC6102 can function from V+ to (V+ – 2V).
Not only does this allow a wide VSENSE range, it also allows
the input reference to be separate from the positive supply
(Figure 6). Note that the difference between VBAT and V+
must be no more than the input sense voltage range listed
in the Electrical Characteristics table.
Monitoring Voltages Above V+ and Level Translation
The LTC6102 may be configured to monitor voltages that are
higher than its supply, provided that the negative terminal
of the input voltage is within the input sense range of the
LTC6102. Figure 7 illustrates a circuit in which the LTC6102
has its supply pin tied to the lower potential terminal of the
sense resistor instead of the higher potential terminal. The
operation of the LTC6102 is such that the –INS and –INF
pins will servo to within a few microvolts of +IN, which is
shorted to V+. Since the input sense range of the LTC6102
includes V+, the circuit will operate properly. The voltage
across RSENSE will be held across RIN by the LTC6102,
causing current VSENSE/RIN to flow to ROUT. In this case,
the supply current of the LTC6102 is also monitored, as
it flows through RSENSE.
Because the voltage across RSENSE is not restricted to
the sense range of the LTC6102 in this circuit, VSENSE
can be large compared to the allowed sense voltage. This
facilitates the sensing of very large voltages, provided
that RIN is chosen so that VSENSE/RIN does not exceed
For more information www.linear.com/LTC6102
6102fe
17
LTC6102
LTC6102-1/LTC6102HV
Applications Information
the allowed output current. The gain is still controlled by
ROUT/RIN, so either gain or attenuation may be applied to
the input signal as it is translated to the output. Finally,
the input may be a voltage source rather than a sense
resistor, as shown in Figure 8. This circuit allows the
translation of a wide variety of input signals across the
entire supply range of the LTC6102 with only a tiny offset
error while retaining simple gain control set by ROUT/RIN.
Again, very large voltages may be sensed as long as RIN
is chosen so that IOUT does not exceed the allowed output
current. For example, VIN may be as large as 1V with RIN =
1k, or as large as 10V with RIN = 10k. For a 10V maximum
input and a 5V maximum output, RIN = 10k and ROUT = 5k
will allow the LTC6102HV to translate VIN to VOUT with a
common mode voltage of up to 100V. For the case where
a large input resistor is used, a similar resistor in series
with +IN will reduce error due to input bias current.
V+
LTC6102 by effectively reducing the supply voltage to the
part by VD.
In addition, if the output of the LTC6102 is wired to a device
that will effectively short it to high voltage (such as through
an ESD protection clamp) during a reverse supply condition, the LTC6102’s output should be connected through
a resistor or Schottky diode (Figure 10).
Response Time
The LTC6102 is designed to exhibit fast response to inputs
for the purpose of circuit protection or signal transmission.
This response time will be affected by the external circuit
in two ways, delay and speed.
RSENSE
+IN
VBATT
V–
RIN
–INS
+IN
+
VCM
V–
–
V+
R2
4.99k
D1
V+
0.1µF
VREG
0.1µF
OUT
LTC6102
–INF
R1
100Ω
–INF
+ –
VREG
L
O
A
D
VIN
–INS
6102 F09
Figure 9. Schottky Prevents Damage During Supply Reversal
LTC6102
OUT
VOUT
ROUT
VOUT = VIN •
VBATT
RSENSE
6102 F08
ROUT
RIN
Figure 8. Voltage Level-Shift Circuit
L
O
A
D
+IN
–INS
+ –
V–
Some applications may be tested with reverse-polarity
supplies due to an expectation of this type of fault during
operation. The LTC6102 is not protected internally from
external reversal of supply polarity. To prevent damage
that may occur during this condition, a Schottky diode
should be added in series with V– (Figure 9). This will
limit the reverse current through the LTC6102. Note that
this diode will limit the low voltage performance of the
18
–INF
V+
VREG
Reverse Supply Current
LTC6102
D1
R1
100Ω
OUT
0.1µF
R3
1k
ADC
R2
4.99k
6102 F10
Figure 10. Additional Resistor R3 Protects
Output During Supply Reversal
6102fe
For more information www.linear.com/LTC6102
LTC6102
LTC6102-1/LTC6102HV
Applications Information
If the output current is very low and an input transient
occurs, there may be a delay before the output voltage
begins changing. This can be reduced by increasing the
minimum output current, either by increasing RSENSE or
decreasing RIN. The effect of increased output current
is illustrated in the step response curves in the Typical
Performance Characteristics section of this datasheet.
Note that the curves are labeled with respect to the initial
output currents.
The speed is also affected by the external circuit. In this
case, if the input changes very quickly, the internal amplifier will slew the gate of the internal output FET (Figure 1)
in order to close the internal loop. This results in current
flowing through RIN and the internal FET. This current slew
rate will be determined by the amplifier and FET characteristics as well as the input resistor, RIN. Using a smaller
RIN will allow the output current to increase more quickly,
decreasing the response time at the output. This will also
have the effect of increasing the maximum output current.
Using a larger ROUT will also decrease the response time,
since VOUT = IOUT • ROUT. Reducing RIN and increasing
ROUT will both have the effect of increasing the voltage
gain of the circuit.
Bandwidth
For applications that require higher bandwidth from the
LTC6102, care must be taken in choosing RIN. For a general-purpose op-amp, the gain-bandwidth product is used
to determine the speed at a given gain. Gain is determined
by external resistors, and the gain-bandwidth product is
an intrinsic property of the amplifier. The same is true
for the LTC6102, except that the feedback resistance is
determined by an internal FET characteristic. The feedback
impedance is approximately 1/gm of the internal MOSFET.
The impedance is reduced as current into –INF is increased.
At 1mA, the impedance of the MOSFET is on the order of
10kΩ. RIN sets the closed-loop gain of the internal loop
as 1/(RIN • gm). The bandwidth is then limited to GBW •
(RIN • gm), with a maximum bandwidth of around 2MHz.
This is illustrated in the characteristic curves, where gain
vs frequency for two input conditions is shown. The exact
impedance of the MOSFET is difficult to determine, as it
is a function of input current, process, and capacitance,
and has a very different characteristic for low currents
vs high currents. However, it is clear that smaller values
of RIN and smaller values of IOUT will generally result in
lower closed-loop bandwidth. VSENSE and RIN should be
chosen to maximize both IOUT and closed-loop gain for
highest speed. Theoretically, maximum bandwidth would
be achieved for the case where VIN = 10VDC and RIN = 10k,
giving IOUT = 1mA and a closed-loop gain near 1. However,
this may not be possible in a practical application. Note
that the MOSFET gm is determined by the average or DC
value of IOUT, not the peak value. Adding DC current to a
small AC input will help increase the bandwidth.
VREG Bypassing
The LTC6102 has an internally regulated supply near V+
for internal bias. It is not intended for use as a supply or
bias pin for external circuitry. A 0.1µF capacitor should be
connected between the VREG and V+ pins. This capacitor
should be located very near to the LTC6102 for the best
performance. In applications which have large supply transients, a 6.8V zener diode may be used in parallel with this
bypass capacitor for additional transient suppression.
Enable Pin Operation
The LTC6102-1 includes an enable pin which can place
the part into a low power disable state. The enable pin is a
logic input pin referenced to V– and accepts standard TTL
logic levels regardless of the V+ voltage. When the enable
pin is driven high, the part is active. When the enable pin is
floating or pulled low, then the part is disabled and draws
very little supply current. When driven high, the enable pin
draws a few microamps of input bias current.
If there is no external logic supply available, the enable
pin can be pulled to the V+ supply through a large value
resistor. The voltage at the enable pin will be clamped
by the built-in ESD protection structure (which acts like
a zener diode). The resistor should be sized so that the
current through the resistor is a few milliamps or less to
prevent any reduction in long-term reliability. For practical purposes, the current through the resistor should be
minimized to save power. The resistor value is limited
by the input bias current requirements of the enable
6102fe
For more information www.linear.com/LTC6102
19
LTC6102
LTC6102-1/LTC6102HV
Applications Information
input resistor RIN) to flow into the output resistor and/or
the output limiting ESD structure in the LTC6102. This is
a temporary condition which will cease when the LTC6102
amplifier settles into normal closed-loop operation.
V+
RIN–
RSENSE
RIN+
+IN
–INS
+
LOAD
RBIAS
2.7M
–
–INF
V–
V+
EN
VREG
LTC6102-1
0.1µF
OUT
VOUT
ROUT
RIN+ = RIN– – RSENSE
6102 F11
Figure 11
pin. Figure 11 shows the LTC6102-1 with a 2.7M pull-up
resistor to limit the current to less than 20µA with a 60V
supply, which is enough to satisfy the input bias current
requirement.
When the LTC6102-1 is disabled, the internal amplifier is
also shut down, which means that the discharge rate of
the 0.1µF capacitor is very low. This is significant when the
LTC6102-1 is disabled to save power, because the recharging of the 0.1µF capacitor is a significant portion of the
overall power consumed in startup. Figure 12 shows the
discharge rate of the 0.1µF capacitor after the LTC6102-1
is shut down at room temperature.
In a system where the LTC6102-1 is disabled for short
periods, the start-up power (and therefore the average
power) can be reduced since the VREG bypass capacitor
is never significantly discharged. The time required to
charge the VREG capacitor will also be reduced, allowing
the LTC6102-1 to start-up more quickly.
2.25
The start-up current of the LTC6102 when the part is
powered on or enabled (LTC6102-1) consists of three
parts: the first is the current necessary to charge the
VREG bypass capacitor, which is nominally 0.1µF. Since the
VREG voltage charges to approximately 4.5V below the V+
voltage, this can require a significant amount of start-up
current. The second source is the active supply current of
the LTC6102 amplifier, which is not significantly greater
during start-up than during normal operation. The third
source is the output current of the LTC6102, which upon
start-up may temporarily drive the output high. This could
cause milliamps of output current (limited mostly by the
1.75
20
ENABLE VOLTAGE (V)
2.00
8.3
8.2
8.1
1.50
8.0
VREG
1.25
1.00
7.9
7.8
EN
0.75
7.7
0.50
7.6
0.25
7.5
0
–2
0
2
4
6
8 10
TIME (ms)
12
14
16
VREG VOLTAGE (V)
Start-Up Current
TA = 25°C
V+ = 12V
7.4
6102 F12
Figure 12. LTC6102-1 VREG Voltage During
Bypass Capacitor Discharge when Disabled
6102fe
For more information www.linear.com/LTC6102
LTC6102
LTC6102-1/LTC6102HV
Typical Applications
Bidirectional Current Sense Circuit with Separate Charge/Discharge Output
ICHARGE
IDISCHARGE
RSENSE
CHARGER
RIN C
100Ω
+IN
VBATT
V–
RIN D
100Ω
RIN C
100Ω
–INS
–INF
+ –
RIN D
100Ω
–INS
–INF
V+
– +
V+
VREG
0.1µF
OUT
LTC6102
+IN
0.1µF
+
ROUT C
4.99k
+
VOUT C VOUT D
–
–
V–
VREG
OUT
L
O
A
D
LTC6102
ROUT D
4.99k
6102 TA02
DISCHARGING: VOUT D = IDISCHARGE • RSENSE
CHARGING: VOUT C = ICHARGE • RSENSE
(
(
)
ROUT D
WHEN IDISCHARGE ≥ 0
RIN D
)
ROUT C
WHEN ICHARGE ≥ 0
RIN C
LTC6102 Monitors Its Own Supply Current
RSENSE
+IN
VBATT
L
O
A
D
ILOAD
–INS
+ –
V–
ISUPPLY
–INF
V+
VREG
LTC6102
R1
100
0.1µF
OUT
R2
4.99k
VOUT = 49.9 • RSENSE (ILOAD + ISUPPLY)
+
–
VOUT
6102 TA03
6102fe
For more information www.linear.com/LTC6102
21
LTC6102
LTC6102-1/LTC6102HV
Typical Applications
16-Bit Resolution Unidirectional Output into LTC2433 ADC
+
4V TO 60V
VSENSE
+IN
–
L
O
A
D
ILOAD
RIN
100Ω
–INS
–INF
+ –
V–
V+
VREG
0.1µF
EN
POWER ENABLE
OUT VOUT
LTC6102-1
4
IN+
1
REF+
VCC
LTC2433-1
ROUT
4.99k
1µF
5V
2
5
IN–
ROUT
VOUT =
• VSENSE = 49.9VSENSE
RIN
8
SDD
TO µP
7
CC
REF– GND
3
9
SCK
FO
6
10
ADC FULL-SCALE = 2.5V
6102 TA05
Intelligent High-Side Switch with Current Monitor
10µF
63V
VLOGIC
14V
47k
FAULT
OFF ON
3
4
100Ω
1%
8
V+
6
VREG
–INS
–INF
RS
LT1910
2
1µF
0.1µF
VO
+IN
100Ω
1
OUT
LTC6102
4.99k
V–
5
SUB85N06-5
L
O
A
D
VO = 49.9 • RS • IL
IL
FOR RS = 5mΩ,
VO = 2.5V AT IL = 10A (FULL SCALE)
6102 TA06
22
6102fe
For more information www.linear.com/LTC6102
LTC6102
LTC6102-1/LTC6102HV
Typical Applications
Input Overvoltage Protection
V+
RIN–
DZ
1k
3W
RSENSE
1k
+IN
–INS
+
LOAD
–
V–
–INF
V+
0.1µF
VREG
OUT
LTC6102
ROUT
DZ: CENTRAL SEMICONDUCTOR
CMZ5931B 18V 1.5W ZENER DIODE
6102 TA07
Simple 500V Current Monitor
DANGER! Lethal Potentials Present — Use Caution
500V
+
VSENSE
RSENSE
–
ISENSE
L
O
A
D
+IN
V–
–INS
RIN
100Ω
–INF
+ –
DANGER!!
HIGH VOLTAGE!!
V+
VREG
0.1µF
OUT
LTC6102
51V
BZX884-C51
M1
VOUT
M1 AND M2 ARE FQD3P50 TM
ROUT
VOUT =
• VSENSE = 49.9 VSENSE
RIN
BAT46
M2
ROUT
4.99k
2M
6102 TA08
6102fe
For more information www.linear.com/LTC6102
23
LTC6102
LTC6102-1/LTC6102HV
Package Description
DD Package
8-Lead Plastic DFN (3mm × 3mm)
(Reference LTC DWG # 05-08-1698 Rev C)
R = 0.125
TYP
5
0.40 ± 0.10
8
0.70 ±0.05
3.5 ±0.05
1.65 ±0.05
2.10 ±0.05 (2 SIDES)
PACKAGE
OUTLINE
0.25 ± 0.05
3.00 ±0.10
(4 SIDES)
PIN 1
TOP MARK
(NOTE 6)
4
0.25 ± 0.05
0.75 ±0.05
0.200 REF
0.50
BSC
2.38 ±0.05
1.65 ± 0.10
(2 SIDES)
1
(DD8) DFN 0509 REV C
0.50 BSC
2.38 ±0.10
BOTTOM VIEW—EXPOSED PAD
0.00 – 0.05
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
NOTE:
1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-1)
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON TOP AND BOTTOM OF PACKAGE
MS8 Package
8-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1660 Rev F)
3.00 ± 0.102
(.118 ± .004)
(NOTE 3)
0.889 ± 0.127
(.035 ± .005)
0.254
(.010)
8
7 6 5
3.00 ± 0.102
(.118 ± .004)
(NOTE 4)
4.90 ± 0.152
(.193 ± .006)
DETAIL “A”
0.52
(.0205)
REF
0° – 6° TYP
GAUGE PLANE
5.23
(.206)
MIN
0.53 ± 0.152
(.021 ± .006)
3.20 – 3.45
(.126 – .136)
DETAIL “A”
0.42 ± 0.038
(.0165 ± .0015)
TYP
0.65
(.0256)
BSC
1.10
(.043)
MAX
2 3
4
0.86
(.034)
REF
0.18
(.007)
SEATING
PLANE
RECOMMENDED SOLDER PAD LAYOUT
NOTE:
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
24
1
0.22 – 0.38
(.009 – .015)
TYP
0.65
(.0256)
BSC
0.1016 ± 0.0508
(.004 ± .002)
MSOP (MS8) 0307 REV F
6102fe
For more information www.linear.com/LTC6102
LTC6102
LTC6102-1/LTC6102HV
Revision History
(Revision history begins at Rev D)
REV
DATE
DESCRIPTION
PAGE NUMBER
D
8/10
Updated graph 21
8
E
6/14
Web Links Added
All
Correction to Output Current Absolute Maximum Ratings, (–1mA, +10mA) instead of (+1mA, –10mA)
2
Correction to Supply Current at V+=60V. Specification does not apply over the full operating temperature range
4
6102fe
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
25
LTC6102
LTC6102-1/LTC6102HV
Typical Application
Remote Current Sense with Simple Noise Filter
V+
RSENSE
TIE AS CLOSE TO RIN AS POSSIBLE
RIN–
+IN
–INS
–
+
LOAD
fC =
1
2 • π • ROUT • COUT
–INF
V–
V+
VREG
OUT
LTC6102
6102 TA09
0.1µF
LONG WIRE
ADC
ROUT
COUT
REMOTE ADC
related parts
PART NUMBER
DESCRIPTION
COMMENTS
LT 1636
Rail-to-Rail Input/Output, Micropower Op Amp
VCM Extends 44V above VEE, 55µA Supply Current, Shutdown Function
LT1637/LT1638/
LT1639
Single/Dual/Quad, Rail-to-Rail, Micropower Op Amp VCM Extends 44V above VEE, 0.4V/µs Slew Rate, >1MHz Bandwidth, <250µA
Supply Current per Amplifier
LT1787/LT1787HV
Precision, Bidirectional, High Side Current Sense
Amplifier
2.7V to 60V Operation, 75µV Offset, 60µA Current Draw
LTC1921
Dual –48V Supply and Fuse Monitor
±200V Transient Protection, Drives Three Optoisolators for Status
LT1990
High Voltage, Gain Selectable Difference Amplifier
±250V Common Mode, Micropower, Pin Selectable Gain = 1, 10
LT1991
Precision, Gain Selectable Difference Amplifier
2.7V to ±18V, Micropower, Pin Selectable Gain = –13 to 14
®
LTC2050/LTC2051/ Single/Dual/Quad Zero-Drift Op Amp
LTC2052
3µV Offset, 30nV/°C Drift, Input Extends Down to V–
LTC4150
Coulomb Counter/Battery Gas Gauge
Indicates Charge Quantity and Polarity
LT6100
Gain-Selectable High Side Current Sense Amplifier
4.1V to 48V Operation, Pin-Selectable Gain: 10, 12.5, 20, 25, 40, 50V/V
LTC6101/
LTC6101HV
High Voltage High Side Current Sense Amplifier in
SOT-23
4V to 60V/5V to 100V Operation, External Resistor Set Gain
LTC6103
Dual High Side Precision Current Sense Amplifier
4V to 60V, Gain Configurable, 8-Pin MSOP
LTC6104
Bidirectional High Side Precision Current Sense
Amplifier
4V to 60V, Gain Configurable, 8-Pin MSOP
LT6105
Precision Rail-to-Rail Input Current Sense Amplifier
Input VCM Extends 44V Above and 0.3V Below V–, 2.85V to 36V Operation
LT6106
Low Cost, High Side Precision Current Sense
Amplifier
2.7V to 36V, Gain Configurable, SOT23
LT6107
High Temperature High Side Current Sense Amplifier 2.7V to 36V, Fully Tested at –55°C and 150°C
in SOT-23
26 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
For more information www.linear.com/LTC6102
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com/LTC6102
6102fe
LT 0614 REV E • PRINTED IN USA
 LINEAR TECHNOLOGY CORPORATION 2007