Strain Reliefs AS85049/49 and MS27506 Strain Reliefs M85049/49-2 S 10 W Glenair Connector Designator F Basic Part No. Material and Finish Designator A = Aluminum, Black Anodize (Non-Self-Locking Only) N = Aluminum, Electroless Nickel S = 300 Series Steel, Passivated (Self-Locking Only) W = Aluminum, 1,000 Hr. Cadmium Olive Drab Over Electroless Nickel S = Self-Locking MIL-DTL-38999 Series I & II, Use Dash for 40M38277, PAN 6433-1, PATT Non-Self-Locking 614, PATT 616, NFC93422 Series HE308 & Shell Size HE309 Cable Entry F Self-Locking Only A Thread E Self-Locking Only H Note: Screw orientation shown is for non-self-locking configuration. Screws on self-locking configurations are on the same side/face of the clamp. TABLE I Dash No. 8 10 12 14 16 18 20 22 24 Shell Size Ref. 8/9 10/11 12/13 14/15 16/17 18/19 20/21 22/23 24/25 A Thread Class 2B .438 - 28 UNEF .562 - 24 UNEF .688 - 24 UNEF .813 - 20 UNEF .938 - 20 UNEF 1.063 - 18 UNEF 1.188 - 18 UNEF 1.313 - 18 UNEF 1.438 - 18 UNEF E Dia Max F Max Self-Locking Self-Locking H Only Only Max .86 (21.8) .91 (23.1) .85 (21.6) .98 (24.9) .91 (23.1) .90 (22.9) 1.16 (29.5) 1.01 (25.7) 1.10 (27.9) 1.28 (32.5) 1.06 (26.9) 1.15 (29.2) 1.41 (35.8) 1.16 (29.5) 1.30 (33.0) 1.52 (38.6) 1.41 (35.8) 1.50 (38.1) 1.64 (41.7) 1.51 (38.4) 1.60 (40.6) 1.77 (45.0) 1.66 (42.2) 1.70 (43.2) 1.89 (48.0) 1.76 (44.7) 1.80 (45.7) Cable Entry Min Max .098 (2.5) .234 (5.9) .153 (3.9) .234 (5.9) .190 (4.8) .328 (8.3) .260 (6.6) .457 (11.6) .283 (7.2) .634 (16.1) .325 (8.3) .614 (15.6) .343 (8.7) .698 (17.7) .381 (9.7) .823 (20.9) .418 (10.6) .853 (21.7) 1. For complete dimensions see applicable Military Specification. 2. Metric dimensions (mm) are indicated in parentheses. 3. Cable Entry is defined as the accomodation entry for the wire bundle or cable. Dimensions are not intended for inspection criteria. © 2005 Glenair, Inc. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com E-Mail: [email protected] 62-19