AD AD9642-210EBZ 14-bit, 170 msps/210 msps/250 msps, 1.8 v analog-to-digital converter (adc) Datasheet

FEATURES
FUNCTIONAL BLOCK DIAGRAM
SNR = 71.0 dBFS at 185 MHz AIN and 250 MSPS
SFDR = 83 dBc at 185 MHz AIN and 250 MSPS
−152.0 dBFS/Hz input noise at 200 MHz, −1 dBFS AIN, 250 MSPS
Total power consumption: 390 mW at 250 MSPS
1.8 V supply voltages
LVDS (ANSI-644 levels) outputs
Integer 1-to-8 input clock divider (625 MHz maximum input)
Sample rates of up to 250 MSPS
Internal ADC voltage reference
Flexible analog input range
1.4 V p-p to 2.0 V p-p (1.75 V p-p nominal)
ADC clock duty cycle stabilizer
Serial port control
Energy saving power-down modes
AVDD
VIN+
PIPELINE
14-BIT
ADC
VIN–
VCM
AGND
DRVDD
D0±/D1±
14
PARALLEL
DDR LVDS
AND
DRIVERS
AD9642
D12±/D13±
DCO±
REFERENCE
1-TO-8
CLOCK
DIVIDER
SERIAL PORT
SCLK
APPLICATIONS
SDIO
CSB
CLK+
CLK–
09995-001
Data Sheet
14-Bit, 170 MSPS/210 MSPS/250 MSPS,
1.8 V Analog-to-Digital Converter (ADC)
AD9642
Figure 1.
Communications
Diversity radio systems
Multimode digital receivers (3G)
TD-SCDMA, WiMAX, WCDMA,
CDMA2000, GSM, EDGE, LTE
I/Q demodulation systems
Smart antenna systems
General-purpose software radios
Ultrasound equipment
Broadband data applications
GENERAL DESCRIPTION
The AD9642 is a 14-bit analog-to-digital converter (ADC) with
sampling speeds of up to 250 MSPS. The AD9642 is designed to
support communications applications, where low cost, small
size, wide bandwidth, and versatility are desired.
The ADC core features a multistage, differential pipelined
architecture with integrated output error correction logic. The
ADC features wide bandwidth inputs that can support a variety
of user-selectable input ranges. An integrated voltage reference
eases design considerations. A duty cycle stabilizer (DCS) is
provided to compensate for variations in the ADC clock duty
cycle, allowing the converter to maintain excellent performance.
The ADC output data is routed directly to the external
14-bit LVDS output port.
Flexible power-down options allow significant power savings,
when desired.
Rev. B
Programming for setup and control is accomplished using a
3-wire SPI-compatible serial interface.
The AD9642 is available in a 32-lead LFCSP and is specified
over the industrial temperature range of −40°C to +85°C. This
product is protected by a U.S. patent.
PRODUCT HIGHLIGHTS
1.
2.
3.
4.
5.
Integrated 14-bit, 170 MSPS/210 MSPS/250 MSPS ADC.
Operation from a single 1.8 V supply and a separate digital
output driver supply accommodating LVDS outputs.
Proprietary differential input maintains excellent SNR
performance for input frequencies of up to 350 MHz.
3-pin, 1.8 V SPI port for register programming and readback.
Pin compatibility with the AD9634, allowing a simple migration from 14 bits to 12 bits, and with the AD6672.
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2011–2015 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD9642
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Theory of Operation ...................................................................... 17
Applications ....................................................................................... 1
ADC Architecture ...................................................................... 17
Functional Block Diagram .............................................................. 1
Analog Input Considerations ................................................... 17
General Description ......................................................................... 1
Voltage Reference ....................................................................... 19
Product Highlights ........................................................................... 1
Clock Input Considerations ...................................................... 19
Revision History ............................................................................... 2
Power Dissipation and Standby Mode .................................... 20
Specifications..................................................................................... 3
Digital Outputs ........................................................................... 20
ADC DC Specifications ............................................................... 3
Serial Port Interface (SPI) .............................................................. 22
ADC AC Specifications ............................................................... 4
Configuration Using the SPI ..................................................... 22
Digital Specifications ................................................................... 5
Hardware Interface ..................................................................... 22
Switching Specifications .............................................................. 6
SPI Accessible Features .............................................................. 23
Timing Specifications .................................................................. 7
Memory Map .................................................................................. 24
Absolute Maximum Ratings ............................................................ 8
Reading the Memory Map Register Table............................... 24
Thermal Characteristics .............................................................. 8
Memory Map Register Table ..................................................... 25
ESD Caution .................................................................................. 8
Applications Information .............................................................. 27
Pin Configurations and Function Descriptions ........................... 9
Design Guidelines ...................................................................... 27
Typical Performance Characteristics ........................................... 10
Outline Dimensions ....................................................................... 28
Equivalent Circuits ......................................................................... 16
Ordering Guide .......................................................................... 28
REVISION HISTORY
1/15—Rev. A to Rev. B
Changes to Features Section............................................................ 1
Changes to Reading the Memory Map Register Table
Section .............................................................................................. 24
Changes to Table 13 ........................................................................ 26
7/14—Rev. 0 to Rev. A
Changes to Features Section............................................................ 1
Changes to Full Power Bandwidth Parameter, Table 2 ................ 5
Deleted Noise Bandwidth Parameter, Table 2............................... 5
7/11—Revision 0: Initial Version
Rev. B | Page 2 of 28
Data Sheet
AD9642
SPECIFICATIONS
ADC DC SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 1.8 V, maximum sample rate, VIN = −1.0 dBFS differential input, 1.75 V p-p full-scale input range, DCS enabled,
unless otherwise noted.
Table 1.
Parameter
RESOLUTION
ACCURACY
No Missing Codes
Offset Error
Gain Error
Differential Nonlinearity (DNL)
Integral Nonlinearity (INL)1
TEMPERATURE DRIFT
Offset Error
Gain Error
INPUT REFERRED NOISE
VREF = 1.0 V
ANALOG INPUT
Input Span
Input Capacitance2
Input Resistance3
Input Common-Mode Voltage
POWER SUPPLIES
Supply Voltage
AVDD
DRVDD
Supply Current
IAVDD1
IDRVDD1
POWER CONSUMPTION
Sine Wave Input (DRVDD = 1.8 V)
Standby Power4
Power-Down Power
Temperature
Full
Min
14
Full
Full
Full
Full
25°C
Full
25°C
AD9642-170
Typ
Max
Min
14
Guaranteed
±11
+2/−11
±0.5
±0.3
±1.3
±0.6
AD9642-210
Typ
Max
Min
14
Guaranteed
±11
+3.5/−8
±0.55
±0.3
±2.0
±0.75
AD9642-250
Typ
Max
Unit
Bits
Guaranteed
±10
+3/−7
±0.6
±1.0
mV
%FSR
LSB
LSB
LSB
LSB
±0.32
±2.5
Full
Full
±7
±52
±7
±105
±7
±75
ppm/°C
ppm/°C
25°C
0.83
0.85
0.85
LSB
rms
Full
Full
Full
Full
1.75
2.5
20
0.9
1.75
2.5
20
0.9
1.75
2.5
20
0.9
V p-p
pF
kΩ
V
Full
Full
1.7
1.7
1.8
1.8
1.9
1.9
Full
Full
123
50
Full
Full
Full
311
50
5
1.7
1.7
1.8
1.8
1.9
1.9
136
64
129
56
360
333
50
5
Measured with a low input frequency, full-scale sine wave.
Input capacitance refers to the effective capacitance between one differential input pin and its complement.
3
Input resistance refers to the effective resistance between one differential input pin and its complement.
4
Standby power is measured with a dc input and the CLK pin inactive (that is, set to AVDD or AGND).
1
2
Rev. B | Page 3 of 28
1.7
1.7
1.8
1.8
1.9
1.9
V
V
139
67
136
64
146
69
mA
mA
371
360
50
5
387
mW
mW
mW
AD9642
Data Sheet
ADC AC SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 1.8 V, maximum sample rate, VIN = −1.0 dBFS differential input, 1.75 V p-p full-scale input range, unless
otherwise noted.
Table 2.
Parameter1
SIGNAL-TO-NOISE RATIO (SNR)
fIN = 30 MHz
fIN = 90 MHz
fIN = 140 MHz
fIN = 185 MHz
fIN = 220 MHz
SIGNAL-TO-NOISE AND DISTORTION
(SINAD)
fIN = 30 MHz
fIN = 90 MHz
fIN = 140 MHz
fIN = 185 MHz
fIN = 220 MHz
EFFECTIVE NUMBER OF BITS (ENOB)
fIN = 30 MHz
fIN = 90 MHz
fIN = 140 MHz
fIN = 185 MHz
fIN = 220 MHz
WORST SECOND OR THIRD HARMONIC
fIN = 30 MHz
fIN = 90 MHz
fIN = 140 MHz
fIN = 185 MHz
fIN = 220 MHz
SPURIOUS-FREE DYNAMIC RANGE
(SFDR)
fIN = 30 MHz
fIN = 90 MHz
fIN = 140 MHz
fIN = 185 MHz
fIN = 220 MHz
WORST OTHER (HARMONIC OR SPUR)
fIN = 30 MHz
fIN = 90 MHz
fIN = 140 MHz
fIN = 185 MHz
fIN = 220 MHz
Temperature
25°C
25°C
Full
25°C
25°C
Full
25°C
Min
AD9642-170
Typ
Max
Min
Min
AD9642-250
Typ
Max
Unit
72.4
72.2
72.2
72.0
71.8
71.2
71.6
71.5
71.8
71.4
70.7
71.0
70.9
71.5
71.3
71.5
71.3
71.2
71.0
70.8
70.3
70.6
70.5
70.9
70.4
69.7
70.1
70.0
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
25°C
25°C
25°C
25°C
25°C
11.6
11.6
11.5
11.4
11.3
11.6
11.6
11.4
11.4
11.3
11.5
11.5
11.5
11.4
11.3
Bits
Bits
Bits
Bits
Bits
25°C
25°C
Full
25°C
25°C
Full
25°C
−96
−95
−96
−92
−90
−89
dBc
dBc
dBc
dBc
dBc
dBc
dBc
25°C
25°C
Full
25°C
25°C
Full
25°C
25°C
25°C
Full
25°C
25°C
Full
25°C
25°C
25°C
Full
25°C
25°C
Full
25°C
72.5
72.2
AD9642-210
Typ
Max
70.7
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
70.0
68.6
69.6
68.7
67.5
−82
−79
−97
−86
−94
−95
−90
−86
−84
−84
−86
96
95
96
92
90
89
97
86
94
95
90
86
84
84
86
−99
−95
−98
−97
−95
−98
−80
82
dBc
dBc
dBc
dBc
dBc
dBc
dBc
79
80
−87
−81
−98
−96
−96
−97
−97
−96
−97
−94
−95
−81
Rev. B | Page 4 of 28
dBc
dBc
dBc
dBc
dBc
dBc
dBc
Data Sheet
Parameter1
TWO-TONE SFDR
fIN = 184.1 MHz, 187.1 MHz (−7 dBFS)
FULL POWER BANDWIDTH
1
AD9642
Temperature
Min
25°C
25°C
AD9642-170
Typ
Max
Min
AD9642-210
Typ
Max
87
1000
88
1000
Min
AD9642-250
Typ
Max
88
1000
Unit
dBc
MHz
See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions.
DIGITAL SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 1.8 V, maximum sample rate, VIN = −1.0 dBFS differential input, 1.0 V internal reference,
DCS enabled, unless otherwise noted.
Table 3.
Parameter
DIFFERENTIAL CLOCK INPUTS (CLK+, CLK−)
Logic Compliance
Internal Common-Mode Bias
Differential Input Voltage
Input Voltage Range
Input Common-Mode Range
High Level Input Current
Low Level Input Current
Input Capacitance
Input Resistance
LOGIC INPUT (CSB)1
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Input Resistance
Input Capacitance
LOGIC INPUT (SCLK)2
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Input Resistance
Input Capacitance
LOGIC INPUTS (SDIO)1
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Input Resistance
Input Capacitance
DIGITAL OUTPUTS
LVDS Data and OR Outputs (OR+, OR−)
Differential Output Voltage (VOD), ANSI Mode
Output Offset Voltage (VOS), ANSI Mode
Differential Output Voltage (VOD), Reduced Swing Mode
Output Offset Voltage (VOS), Reduced Swing Mode
1
2
Temperature
Full
Full
Full
Full
Full
Full
Full
Full
Min
0.3
AGND
0.9
10
−22
12
Full
Full
Full
Full
Full
Full
1.22
0
50
−5
Full
Full
Full
Full
Full
Full
1.22
0
45
−5
Full
Full
Full
Full
Full
Full
1.22
0
45
−5
Full
Full
Full
Full
250
1.15
150
1.15
Pull-up.
Pull-down.
Rev. B | Page 5 of 28
Typ
Max
CMOS/LVDS/LVPECL
0.9
3.6
AVDD
1.4
22
−10
4
15
18
V
V p-p
V
V
µA
µA
pF
kΩ
2.1
0.6
71
+5
V
V
µA
µA
kΩ
pF
2.1
0.6
70
+5
V
V
µA
µA
kΩ
pF
2.1
0.6
70
+5
V
V
µA
µA
kΩ
pF
450
1.35
280
1.35
mV
V
mV
V
26
2
26
2
26
5
350
1.25
200
1.25
Unit
AD9642
Data Sheet
SWITCHING SPECIFICATIONS
Table 4.
AD9642-210
AD9642-170
Parameter
CLOCK INPUT PARAMETERS
Input Clock Rate
Conversion Rate1
CLK Period—Divide-by-1 Mode (tCLK)
CLK Pulse Width High (tCH)
Divide-by-1 Mode, DCS Enabled
Divide-by-1 Mode, DCS Disabled
Divide-by-2 Mode Through
Divide-by-8 Mode
Aperture Delay (tA)
Aperture Uncertainty (Jitter, tJ)
DATA OUTPUT PARAMETERS
Data Propagation Delay (tPD)
DCO Propagation Delay (tDCO)
DCO-to-Data Skew (tSKEW)
Pipeline Delay (Latency)
Wake-Up Time (from Standby)
Wake-Up Time (from Power-Down)
Out-of-Range Recovery Time
1
Temp
Min
Full
Full
Full
40
5.8
Full
Full
Full
2.61
2.76
0.8
Typ
Max
625
170
2.9
2.9
Full
Full
3.19
3.05
Min
2.16
2.28
0.8
Max
625
210
40
4.8
1.0
0.1
Full
Full
Full
Full
Full
Full
Full
Typ
2.4
2.4
2.64
2.52
AD9642-250
Min
40
4
1.8
1.9
0.8
1.0
0.1
4.1
4.7
4.7
5.3
5.2
5.8
4.1
4.7
4.7
5.3
0.3
0.5
10
10
100
3
0.7
0.3
0.5
10
10
100
3
Typ
2.0
2.0
Max
Unit
625
250
MHz
MSPS
ns
2.2
2.1
ns
ns
ns
1.0
0.1
ns
ps rms
4.1
4.7
4.7
5.3
5.2
5.8
0.7
0.3
0.5
10
10
100
3
0.7
5.2
5.8
ns
ns
ns
Cycles
μs
μs
Cycles
Conversion rate is the clock rate after the divider.
Timing Diagram
tA
N–1
N+4
N+5
N
N+3
VIN
N+1
tCH
N+2
tCLK
CLK+
CLK–
tDCO
DCO–
DCO+
tSKEW
D0±/D1±
(LSB)
D0
N – 10
D1
N – 10
D0
N–9
D1
N–9
D0
N–8
D1
N–8
D0
N–7
D1
N–7
D0
N–6
D12±/D13±
(MSB)
D12
N – 10
D13
N – 10
D12
N–9
D13
N–9
D12
N–8
D13
N–8
D12
N–7
D12
N–7
D12
N–6
EVEN/ODD
Figure 2. LVDS Data Output Timing
Rev. B | Page 6 of 28
09995-002
tPD
Data Sheet
AD9642
TIMING SPECIFICATIONS
Table 5.
Parameter
SPI TIMING REQUIREMENTS
tDS
tDH
tCLK
tS
tH
tHIGH
tLOW
tEN_SDIO
tDIS_SDIO
Test Conditions/Comments
See Figure 58 for SPI timing diagram
Setup time between the data and the rising edge of SCLK
Hold time between the data and the rising edge of SCLK
Period of the SCLK
Setup time between CSB and SCLK
Hold time between CSB and SCLK
Minimum period that SCLK should be in a logic high state
Minimum period that SCLK should be in a logic low state
Time required for the SDIO pin to switch from an input to an output
relative to the SCLK falling edge (not shown in Figure 58)
Time required for the SDIO pin to switch from an output to an input
relative to the SCLK rising edge (not shown in Figure 58)
Rev. B | Page 7 of 28
Min
Typ
Max
Unit
2
2
40
2
2
10
10
10
ns
ns
ns
ns
ns
ns
ns
ns
10
ns
AD9642
Data Sheet
ABSOLUTE MAXIMUM RATINGS
Table 6.
Parameter
Electrical
AVDD to AGND
DRVDD to AGND
VIN+, VIN− to AGND
CLK+, CLK− to AGND
VCM to AGND
CSB to AGND
SCLK to AGND
SDIO to AGND
D0−/D1−, D0+/D1+ Through
D12−/D13−, D12+/D13+ to AGND
DCO+, DCO− to AGND
Environmental
Operating Temperature Range
(Ambient)
Maximum Junction Temperature
Under Bias
Storage Temperature Range
(Ambient)
THERMAL CHARACTERISTICS
Rating
−0.3 V to +2.0 V
−0.3 V to +2.0 V
−0.3 V to AVDD + 0.2 V
−0.3 V to AVDD + 0.2 V
−0.3 V to AVDD + 0.2 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
The exposed paddle must be soldered to the ground plane for the
LFCSP package. Soldering the exposed paddle to the customer
board increases the reliability of the solder joints, maximizing
the thermal capability of the package.
Table 7. Thermal Resistance
Package Type
32-Lead LFCSP
5 mm × 5 mm
(CP-32-12)
−0.3 V to DRVDD + 0.3 V
Airflow
Velocity
(m/sec)
0
1.0
2.0
θJA1, 2
37.1
32.4
29.1
θJC1, 3
3.1
θJB1, 4
20.7
Unit
°C/W
°C/W
°C/W
1
Per JEDEC 51-7, plus JEDEC 25-5 2S2P test board.
Per JEDEC JESD51-2 (still air) or JEDEC JESD51-6 (moving air).
3
Per MIL-Std 883, Method 1012.1.
4
Per JEDEC JESD51-8 (still air).
2
−40°C to +85°C
150°C
−65°C to +125°C
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Typical θJA is specified for a 4-layer PCB with a solid ground
plane. As shown in Table 7, airflow increases heat dissipation,
which reduces θJA. In addition, metal in direct contact with the
package leads from metal traces—through holes, ground, and
power planes—reduces the θJA.
ESD CAUTION
Rev. B | Page 8 of 28
Data Sheet
AD9642
32
31
30
29
28
27
26
25
AVDD
AVDD
VIN+
VIN–
AVDD
AVDD
VCM
DNC
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
AD9642
INTERLEAVED
LVDS
TOP VIEW
(Not to Scale)
24
23
22
21
20
19
18
17
CSB
SCLK
SDIO
DCO+
DCO–
D12+/D13+ (MSB)
D12–/D13– (MSB)
DRVDD
NOTES
1. THE EXPOSED THERMAL PADDLE ON THE BOTTOM OF THE
PACKAGE PROVIDES THE ANALOG GROUND FOR THE
PART. THIS EXPOSED PADDLE MUST BE CONNECTED TO
GROUND FOR PROPER OPERATION.
2. DNC = DO NOT CONNECT. DO NOT CONNECT TO THIS PIN.
09995-003
D4–/D5–
D4+/D5+
D6–/D7–
D6+/D7+
D8–/D9–
D8+/D9+
D10–/D11–
D10+/D11+
9
10
11
12
13
14
15
16
CLK+
CLK–
AVDD
D0–/D1– (LSB)
D0+/D1+ (LSB)
D2–/D3–
D2+/D3+
DRVDD
Figure 3. LFCSP Pin Configuration (Top View)
Table 8. Pin Function Descriptions
Pin No.
ADC Power Supplies
8, 17
3, 27, 28, 31, 32
0
25
ADC Analog
30
29
26
Mnemonic
Type
Description
DRVDD
AVDD
AGND,
Exposed Paddle
Supply
Supply
Ground
Digital Output Driver Supply (1.8 V Nominal).
Analog Power Supply (1.8 V Nominal).
Analog Ground. The exposed thermal paddle on the bottom of the package provides
the analog ground for the part. This exposed paddle must be connected to ground for
proper operation.
Do Not Connect. Do not connect to this pin.
VIN+
VIN−
VCM
Input
Input
Output
Differential Analog Input Pin (+).
Differential Analog Input Pin (−).
Common-Mode Level Bias Output for Analog Inputs. This pin should be decoupled
CLK+
CLK−
Input
Input
ADC Clock Input—True.
ADC Clock Input—Complement.
D0+/D1+ (LSB)
D0−/D1− (LSB)
D2+/D3+
D2−/D3−
D4+/D5+
D4−/D5−
D6+/D7+
D6−/D7−
D8+/D9+
D8−/D9−
D10+/D11+
D10−/D11−
D12+/D13+ (MSB)
D12−/D13− (MSB)
DCO+
DCO−
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
DDR LVDS Output Data 0/1—True.
DDR LVDS Output Data 0/1—Complement.
DDR LVDS Output Data 2/3—True.
DDR LVDS Output Data 2/3—Complement.
DDR LVDS Output Data 4/5—True.
DDR LVDS Output Data 4/5—Complement.
DDR LVDS Output Data 6/7—True.
DDR LVDS Output Data 6/7—Complement.
DDR LVDS Output Data 8/9—True.
DDR LVDS Output Data 8/9—Complement.
DDR LVDS Output Data 10/11—True.
DDR LVDS Output Data 10/11—Complement.
DDR LVDS Output Data 12/13—True.
DDR LVDS Output Data 12/13—Complement.
LVDS Data Clock Output—True.
LVDS Data Clock Output—Complement.
SCLK
SDIO
CSB
Input
Input/output
Input
SPI Serial Clock.
SPI Serial Data I/O.
SPI Chip Select (Active Low).
DNC
to ground using a 0.1 μF capacitor.
1
2
Digital Outputs
5
4
7
6
10
9
12
11
14
13
16
15
19
18
21
20
SPI Control
23
22
24
Rev. B | Page 9 of 28
AD9642
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
AVDD = 1.8 V, DRVDD = 1.8 V, sample rate = maximum rate per speed grade, DCS enabled, 1.75 V p-p differential input, VIN = −1.0 dBFS,
32k sample, TA = 25°C, unless otherwise noted.
0
0
170MSPS
90.1MHz @ –1dBFS
SNR = 71.82dB (72.2dBFS)
SFDR = 93dBc
–20
–40
AMPLITUDE (dBFS)
–60
SECOND HARMONIC
–80
THIRD HARMONIC
–100
SECOND HARMONIC
THIRD HARMONIC
–80
–100
–120
–120
10
20
50
60
30
40
FREQUENCY (MHz)
70
80
–140
0
Figure 4. AD9642-170 Single-Tone FFT with fIN = 90.1 MHz
10
20
50
60
30
40
FREQUENCY (MHz)
70
09995-106
0
09995-004
–140
80
Figure 7. AD9642-170 Single-Tone FFT with fIN = 305.1 MHz
120
0
170MSPS
185.1MHz @ –1dBFS
SNR = 70.2dB (71.2dBFS)
SFDR = 86dBc
SFDR (dBFS)
100
SNR/SFDR (dBc AND dBFS)
–20
–40
–60
THIRD HARMONIC
–80
SECOND HARMONIC
–100
80
SNR (dBFS)
60
SFDR (dBc)
40
SNR (dBc)
20
–120
0
10
20
30
40
50
60
FREQUENCY (MHz)
70
80
0
–100
09995-005
–140
Figure 5. AD9642-170 Single-Tone FFT with fIN = 185.1 MHz
–90
–80
–70 –60 –50 –40 –30
INPUT AMPLITUDE (dBFS)
–20
–10
0
09995-007
AMPLITUDE (dBFS)
–60
Figure 8. AD9642-170 Single-Tone SNR/SFDR vs. Input Amplitude (AIN)
with fIN = 90.1 MHz, fS = 170 MSPS
0
100
170MSPS
220.1MHz @ –1dBFS
SNR = 69.7dB (70.7dBFS)
SFDR = 84dBc
–20
95
SFDR (dBc)
90
SUPPLY CURRENT (A)
–40
–60
THIRD HARMONIC
–80
SECOND HARMONIC
–100
85
80
SNR (dBFS)
75
70
–120
65
0
10
20
30
40
50
60
FREQUENCY (MHz)
70
80
Figure 6. AD9642-170 Single-Tone FFT with fIN = 220.1 MHz
60
60
09995-006
–140
75
90
105
120
150
180
210
240
270
300
330
135 165 195 225 255 285 315 345
FREQUENCY (MHz)
09995-058
AMPLITUDE (dBFS)
–40
AMPLITUDE (dBFS)
170MSPS
305.1MHz @ –1dBFS
SNR = 68.0dB (69.0dBFS)
SFDR = 86dBc
–20
Figure 9. AD9642-170 Single-Tone SNR/SFDR vs. Input Frequency (fIN),
fS = 170 MSPS
Rev. B | Page 10 of 28
Data Sheet
AD9642
0
0
–20
SFDR/IMD3 (dBc AND dBFS)
170MSPS
184.12MHz @ –7dBFS
187.12MHz @ –7dBFS
SFDR = 87dBc (94dBFS)
–20
SFDR (dBc)
AMPLITUDE (dBFS)
–40
–40
IMD3 (dBc)
–60
–80
SFDR (dBFS)
–100
–60
–80
–100
–120
INPUT AMPLITUDE (dBFS)
–140
09995-009
–120
–90.0 –81.7 –73.4 –65.1 –56.8 –48.5 –40.2 –31.9 –23.6 –15.3 –7.0
Figure 10. AD9642-170 Two-Tone SFDR/IMD3 vs. Input Amplitude (AIN) with
fIN1 = 89.12 MHz, fIN2 = 92.12 MHz, fS = 170 MSPS
0
10
50
60
30
40
FREQUENCY (MHz)
20
80
70
09995-012
IMD3 (dBFS)
Figure 13. AD9642-170 Two Tone FFT with fIN1 = 184.12 MHz, fIN2 = 187.12 MHz
0
100
–20
95
SFDR (dBFS)
SNR/SFDR (dBc and dBFS)
SFDR/IMD3 (dBc AND dBFS)
SFDR (dBc)
–40
IMD3 (dBc)
–60
–80
SFDR (dBFS)
90
85
80
75
–100
SNR (dBc)
70
40
09995-010
–120
–90.0 –81.7 –73.4 –65.1 –56.8 –48.5 –40.2 –31.9 –23.6 –15.3 –7.0
INPUT AMPLITUDE (dBFS)
50
60
70
80
09995-013
IMD3 (dBFS)
90 100 110 120 130 140 150 160 170
SAMPLE RATE (MSPS)
Figure 14. AD9642-170 Single-Tone SNR/SFDR vs. Sample Rate (fS)
with fIN = 90 MHz
Figure 11. AD9642-170 Two-Tone SFDR/IMD3 vs. Input Amplitude (AIN)
with fIN1 = 184.12 MHz, fIN2 = 187.12 MHz, fS = 170 MSPS
6000
0
170MSPS
89.12MHz @ –7dBFS
92.12MHz @ –7dBFS
SFDR = 88dBc (95dBFS)
–20
0.830 LSB rms
16,384 TOTAL HITS
5000
NUMBER OF HITS
–60
–80
4000
3000
2000
–100
1000
Rev. B | Page 11 of 28
N+6
N+5
N+4
09995-014
OUTPUT CODE
Figure 12. AD9642-170 Two-Tone FFT with fIN1 = 89.12 MHz, fIN2 = 92.12 MHz
N+3
0
N+2
80
N
70
N+1
30
40
50
60
FREQUENCY (MHz)
N–1
20
N–2
10
N–3
0
N–4
–140
09995-011
–120
N–5
AMPLITUDE (dBFS)
–40
Figure 15. AD9642-170 Grounded Input Histogram, fS = 170 MSPS
AD9642
Data Sheet
0
0
210MSPS
90.1MHz @ –1dBFS
SNR = 71.2dB (72.2dBFS)
SFDR = 92dBc
–20
–40
AMPLITUDE (dBFS)
–60
THIRD HARMONIC
–80
SECOND HARMONIC
–100
–60
THIRD HARMONIC
–80
–100
–120
–120
15
30
45
60
75
90
105
FREQUENCY (MHz)
–140
0
15
60
45
30
105
90
75
09995-117
0
09995-015
–140
FREQUENCY (MHz)
Figure 19. AD9642-210 Single-Tone FFT with fIN = 305.1 MHz
Figure 16. AD9642-210 Single-Tone FFT with fIN = 90.1 MHz
120
0
210MSPS
185.1MHz @ –1dBFS
SNR = 70.5dB (71.5dBFS)
SFDR = 93dBc
SFDR (dBFS)
100
SNR/SFDR (dBc AND dBFS)
–20
–40
–60
SECOND HARMONIC
–80
THIRD HARMONIC
–100
80
SNR (dBFS)
60
SFDR (dBc)
40
SNR (dBc)
0
15
30
45
60
75
90
105
FREQUENCY (MHz)
0
–100
09995-016
–140
Figure 17. AD9642-210 Single-Tone FFT with fIN = 185.1 MHz
–90
–80
–70 –60 –50 –40 –30
INPUT AMPLITUDE (dBFS)
–20
–10
0
09995-018
20
–120
Figure 20. AD9642-210 Single-Tone SNR/SFDR vs. Input Amplitude (AIN)
with fIN = 90.1 MHz, fS = 210 MSPS
100
0
210MSPS
220.1MHz @ –1dBFS
SNR = 70dB (71dBFS)
SFDR = 84dBc
95
SFDR (dBc)
SNR/SFDR (dBc and dBFS)
–20
–40
SECOND HARMONIC
–60
THIRD HARMONIC
–80
–100
–120
90
85
80
75
SNR (dBFS)
70
Figure 18. AD9642-210 Single-Tone FFT with fIN = 220.1 MHz
345
330
315
300
285
270
255
240
225
FREQUENCY (MHz)
09995-019
FREQUENCY (MHz)
60
210
105
195
90
180
75
165
60
150
45
135
30
120
15
60
0
09995-017
–140
90
65
105
AMPLITUDE (dBFS)
SECOND HARMONIC
75
AMPLITUDE (dBFS)
–40
AMPLITUDE (dBFS)
210MSPS
305.1MHz @ –1dBFS
SNR = 68.7dB (69.7dBFS)
SFDR = 83dBc
–20
Figure 21. AD9642-210 Single-Tone SNR/SFDR vs. Input Frequency (fIN),
fS = 210 MSPS
Rev. B | Page 12 of 28
Data Sheet
AD9642
0
0
–20
–20
SFDR (dBc)
–40
–40
AMPLITUDE (dBFS)
SFDR/IMD3 (dBc AND dBFS)
210MSPS
184.12MHz AT –7dBFS
187.12MHz AT –7dBFS
SFDR = 88dBc (95dBFS)
IMD3 (dBc)
–60
–80
SFDR (dBFS)
–60
–80
–100
–100
–120
09995-020
–120
–90.0 –81.7 –73.4 –65.1 –56.8 –48.5 –40.2 –31.9 –23.6 –15.3 –7.0
INPUT AMPLITUDE (dBFS)
–140
0
15
30
45
60
75
90
09995-023
IMD3 (dBFS)
105
FREQUENCY (MHz)
Figure 25. AD9642-210 Two-Tone FFT with fIN1 = 184.12 MHz, fIN2 = 187.12 MHz
Figure 22. AD9642-210 Two-Tone SFDR/IMD3 vs. Input Amplitude (AIN)
with fIN1 = 89.12 MHz, fIN2 = 92.12 MHz, fS = 210 MSPS
0
100
–20
95
SFDR (dBc)
SNR/SFDR (dBc and dBFS)
SFDR/IMD3 (dBc AND dBFS)
SFDR (dBc)
–40
IMD3 (dBc)
–60
–80
SFDR (dBFS)
90
85
80
75
–100
SNR (dBFS)
IMD3 (dBFS)
200
210
190
180
160
170
140
150
130
110
120
90
100
80
60
70
50
40
09995-024
INPUT AMPLITUDE (dBFS)
70
09995-021
–120
–90.0 –81.7 –73.4 –65.1 –56.8 –48.5 –40.2 –31.9 –23.6 –15.3 –7.0
SAMPLE RATE (MSPS)
Figure 23. AD9642-210 Two-Tone SFDR/IMD3 vs. Input Amplitude (AIN)
with fIN1 = 184.12 MHz, fIN2 = 187.12 MHz, fS = 210 MSPS
Figure 26. AD9642-210 Single-Tone SNR/SFDR vs. Sample Rate (fS)
with fIN = 90 MHz
0
6000
210MSPS
89.12MHz @ –7dBFS
92.12MHz @ –7dBFS
SFDR = 89dBc (96dBFS)
–20
0.852 LSB rms
16,384 TOTAL HITS
5000
NUMBER OF HITS
–60
–80
–100
4000
3000
2000
1000
Rev. B | Page 13 of 28
N+6
09995-025
OUTPUT CODE
Figure 24. AD9642-210 Two-Tone FFT with fIN1 = 89.12 MHz, fIN2 = 92.12 MHz
N+5
0
N+4
105
N+3
90
N+2
FREQUENCY (MHz)
75
N+1
60
N
45
N–1
30
N–2
15
N–3
0
N–4
–140
09995-022
–120
N–5
AMPLITUDE (dBFS)
–40
Figure 27. AD9642-210 Grounded Input Histogram, fS = 210 MSPS
AD9642
Data Sheet
0
0
250MSPS
90.1MHz @ –1dBFS
SNR = 71dB (72dBFS)
SFDR = 89dBc
SECOND HARMONIC
–80
–100
–120
–120
0
25
50
75
125
100
FREQUENCY (MHz)
–140
0
25
50
75
100
125
FREQUENCY (MHz)
Figure 28. AD9642-250 Single-Tone FFT with fIN = 90.1 MHz
Figure 31. AD9642-250 Single-Tone FFT with fIN = 305.1 MHz
0
120
250MSPS
185.1MHz @ –1dBFS
SNR = 70.4dB (71.4dBFS)
SFDR = 86dBc
SFDR (dBFS)
100
SNR/SFDR (dBc AND dBFS)
–20
–40
THIRD HARMONIC
–60
SECOND HARMONIC
–80
–100
80
SNR (dBFS)
60
SFDR (dBc)
40
SNR (dBc)
0
25
50
75
100
125
FREQUENCY (MHz)
0
–100
09995-027
–140
–90
–70 –60 –50 –40 –30
INPUT AMPLITUDE (dBFS)
–80
–20
–10
0
09995-029
20
–120
Figure 32. AD9642-250 Single-Tone SNR/SFDR vs. Input Amplitude (AIN)
with fIN = 90.1 MHz, fS = 250 MSPS
Figure 29. AD9642-250 Single-Tone FFT with fIN = 185.1 MHz
100
0
250MSPS
220.1MHz @ 1.0dBFS
SNR = 69.9dB (70.9dBFS)
SFDR = 91dBc
95
SFDR (dBFS)
SNR/SFDR (dBc and dBFS)
–20
–40
–60
THIRD HARMONIC
SECOND HARMONIC
–80
–100
90
85
80
75
70
SNR (dBc)
–120
345
330
315
300
285
255
270
240
225
210
180
195
FREQUENCY (MHz)
09995-030
FREQUENCY (MHz)
60
165
125
150
100
135
75
120
50
90
25
105
0
60
–140
75
65
09995-059
AMPLITUDE (dBFS)
SECOND HARMONIC
THIRD HARMONIC
–100
–140
AMPLITUDE (dBFS)
–60
Figure 33. AD9642-250 Single-Tone SNR/SFDR vs. Input Frequency (fIN),
fS = 250 MSPS
Figure 30. AD9642-250 Single-Tone FFT with fIN = 220.1 MHz
Rev. B | Page 14 of 28
09995-128
THIRD HARMONIC
–80
–40
AMPLITUDE (dBFS)
–40
–60
250MSPS
305.1MHz @ –1dBFS
SNR = 68.5dB (69.5dBFS)
SFDR = 82dBc
–20
09995-026
AMPLITUDE (dBFS)
–20
Data Sheet
AD9642
0
0
–20
SFDR (dBc)
–40
AMPLITUDE (dBFS)
SFDR/IMD3 (dBc and dBFS)
250MSPS
184.12MHz AT –7dBFS
187.12MHz AT –7dBFS
SFDR = 87dBc (94dBFS)
–20
–40
IMD3 (dBc)
–60
–80
SFDR (dBFS)
–100
–60
–80
–100
–120
INPUT AMPLITUDE (dBFS)
Figure 34. AD9642-250 Two-Tone SFDR/IMD3 vs. Input Amplitude (AIN)
with fIN1 = 89.12 MHz, fIN2 = 92.12 MHz, fS = 250 MSPS
0
25
50
75
100
125
FREQUENCY (MHz)
Figure 37. AD9642-250 Two Tone FFT with fIN1 = 184.12 MHz, fIN2 = 187.12 MHz
0
100
–20
95
SFDR (dBc)
SNR/SFDR (dBFS/dBc)
SFDR/IMD3 (dBc and dBFS)
–140
09995-031
–120
–90.0 –81.7 –73.4 –65.1 –56.8 –48.5 –40.2 –31.9 –23.6 –15.3 –7.0
09995-034
IMD3 (dBFS)
–40
IMD3 (dBc)
–60
–80
SFDR (dBFS)
–100
90
SFDR
85
80
75
SNR
INPUT AMPLITUDE (dBFS)
Figure 35. AD9642-250 Two-Tone SFDR/IMD3 vs. Input Amplitude (AIN)
with fIN1 = 184.12 MHz, fIN2 = 187.12 MHz, fS = 250 MSPS
SAMPLE RATE (MSPS)
Figure 38. AD9642-250 Single-Tone SNR/SFDR vs. Sample Rate (fS)
with fIN = 90 MHz
5000
0
250MSPS
89.12MHz @ –7.0dBFS
92.12MHz @ –7.0dBFS
SFDR = 88dBc (95dBFS)
–20
4500
0.847LSB rms
16,384 TOTAL HITS
4000
–40
NUMBER OF HITS
AMPLITUDE (dBFS)
250
70
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
–7.0
09995-032
–120
–90.0 –81.7 –73.4 –65.1 –56.8 –48.5 –40.2 –31.9 –23.6 –15.3
09995-035
IMD3 (dBFS)
–60
–80
3500
3000
2500
2000
1500
–100
1000
–120
25
50
75
FREQUENCY (MHz)
100
125
0
09995-033
0
N–4 N–3 N–2 N–1 N N+1 N+2 N+3 N+4 N+5
OUTPUT CODE
Figure 36. AD9642-250 Two-Tone FFT with fIN1 = 89.12 MHz, fIN2 = 92.12 MHz
Rev. B | Page 15 of 28
09995-036
500
–140
Figure 39. AD9642-250 Grounded Input Histogram, fS = 250 MSPS
AD9642
Data Sheet
EQUIVALENT CIRCUITS
DRVDD
AVDD
VIN
350Ω
SDIO
09995-040
09995-037
26kΩ
Figure 43. Equivalent SDIO Circuit
Figure 40. Equivalent Analog Input Circuit
AVDD
AVDD
AVDD
0.9V
15kΩ
CLK–
26kΩ
09995-041
09995-038
CLK+
350Ω
SCLK
15kΩ
Figure 41. Equivalent Clock Input Circuit
Figure 44. Equivalent SCLK Input Circuit
DRVDD
AVDD
26kΩ
DATAOUT–
350Ω
DATAOUT+
V+
09995-039
V–
CSB
V–
09995-042
V+
Figure 45. Equivalent CSB Input Circuit
Figure 42. Equivalent LVDS Output Circuit
Rev. B | Page 16 of 28
Data Sheet
AD9642
THEORY OF OPERATION
The AD9642 can sample any fS/2 frequency segment from dc to
250 MHz using appropriate low-pass or band-pass filtering at
the ADC inputs with little loss in ADC performance.
“Transformer-Coupled Front-End for Wideband A/D Converters,”
for more information on this subject.
BIAS
Programming and control of the AD9642 are accomplished
using a 3-pin, SPI-compatible serial interface.
S
S
CFB
CS
VIN+
CPAR1
The AD9642 architecture consists of a front-end sample-andhold circuit, followed by a pipelined switched-capacitor ADC.
The quantized outputs from each stage are combined into a
final 14-bit result in the digital correction logic. The pipelined
architecture permits the first stage to operate on a new input
sample and the remaining stages to operate on the preceding
samples. Sampling occurs on the rising edge of the clock.
Each stage of the pipeline, excluding the last, consists of a low
resolution flash ADC connected to a switched-capacitor digitalto-analog converter (DAC) and an interstage residue amplifier
(MDAC). The MDAC magnifies the difference between the
reconstructed DAC output and the flash input for the next stage
in the pipeline. One bit of redundancy is used in each stage to
facilitate digital correction of flash errors. The last stage simply
consists of a flash ADC.
The input stage of the AD9642 contains a differential sampling
circuit that can be ac- or dc-coupled in differential or singleended modes. The output staging block aligns the data, corrects
errors, and passes the data to the output buffers. The output
buffers are powered from a separate supply, allowing digital
output noise to be separated from the analog core. During
power-down, the output buffers go into a high impedance state.
ANALOG INPUT CONSIDERATIONS
The analog input to the AD9642 is a differential switchedcapacitor circuit that has been designed to attain optimum
performance when processing a differential input signal.
CPAR2
H
S
S
CS
VIN–
CPAR1
CPAR2
CFB
S
S
09995-043
ADC ARCHITECTURE
BIAS
Figure 46. Switched-Capacitor Input
For best dynamic performance, match the source impedances
driving VIN+ and VIN− and differentially balance the inputs.
Input Common Mode
The analog inputs of the AD9642 are not internally dc biased.
In ac-coupled applications, the user must provide this bias
externally. Setting the device so that VCM = 0.5 × AVDD (or
0.9 V) is recommended for optimum performance. An onboard common-mode voltage reference is included in the
design and is available from the VCM pin. Using the VCM
output to set the input common mode is recommended.
Optimum performance is achieved when the common-mode
voltage of the analog input is set by the VCM pin voltage
(typically 0.5 × AVDD). The VCM pin must be decoupled to
ground by a 0.1 μF capacitor, as described in the Applications
Information section. Place this decoupling capacitor close to the
pin to minimize the series resistance and inductance between
the part and this capacitor.
Differential Input Configurations
A small resistor in series with each input can help reduce the
peak transient current required from the output stage of the
driving source. A shunt capacitor can be placed across the
inputs to provide dynamic charging currents. This passive
network creates a low-pass filter at the ADC input; therefore,
the precise values are dependent on the application.
The output common-mode voltage of the ADA4930-1 is easily
set with the VCM pin of the AD9642 (see Figure 47), and the
driver can be configured in a Sallen-Key filter topology to
provide band-limiting of the input signal.
15pF
200Ω
VIN
In intermediate frequency (IF) undersampling applications, the
shunt capacitors should be reduced. In combination with the
driving source impedance, the shunt capacitors limit the input
bandwidth. Refer to the AN-742 Application Note, Frequency
Domain Response of Switched-Capacitor ADCs; the AN-827
Application Note, A Resonant Approach to Interfacing Amplifiers
to Switched-Capacitor ADCs; and the Analog Dialogue article,
Rev. B | Page 17 of 28
76.8Ω
33Ω
90Ω
15Ω
VIN–
AVDD
5pF
ADA4930-1
0.1µF
ADC
33Ω
120Ω
200Ω
15Ω
VIN+
VCM
15pF
0.1µF
Figure 47. Differential Input Configuration Using the ADA4930-1
09995-044
The clock signal alternatively switches the input between
sample mode and hold mode (see the configuration shown in
Figure 46). When the input is switched into sample mode, the
signal source must be capable of charging the sampling
capacitors and settling within 1/2 clock cycle.
Optimum performance can be achieved when driving the AD9642
in a differential input configuration. For baseband applications,
the AD8138, ADA4937-1, and ADA4930-1 differential drivers
provide excellent performance and a flexible interface to the ADC.
AD9642
Data Sheet
adjusted or some components may need to be removed. Table 9
displays recommended values to set the RC network for different
input frequency ranges. However, these values are dependent on
the input signal and bandwidth and should be used only as a
starting guide. Note that the values given in Table 9 are for each
R1, R2, C2, and R3 component shown in Figure 48 and Figure 50.
For baseband applications where SNR is a key parameter,
differential transformer coupling is the recommended input
configuration. An example is shown in Figure 48. To bias the
analog input, connect the VCM voltage to the center tap of the
secondary winding of the transformer.
C2
R2
Table 9. Example RC Network
VIN+
Frequency
Range
(MHz)
0 to 100
100 to 300
R1
49.9Ω
C1
ADC
R2
R1
0.1µF
VCM
VIN–
R3
0.1µF
09995-045
C2
R1
Series
(Ω)
33
15
C1
Differential
(pF)
8.2
3.9
R2
Series
(Ω)
0
0
The signal characteristics must be considered when selecting
a transformer. Most RF transformers saturate at frequencies
below a few megahertz. Excessive signal power can also cause
core saturation, which leads to distortion.
1000pF
At input frequencies in the second Nyquist zone and above, the
noise performance of most amplifiers is not adequate to achieve
the true SNR performance of the AD9642. For applications where
SNR is a key parameter, differential double balun coupling is
the recommended input configuration (see Figure 50). In this
configuration, the input is ac-coupled and the VCM voltage is
provided to each input through a 33 Ω resistor. This resistor
compensates for losses in the input baluns to provide a 50 Ω
impedance to the driver.
165Ω
15pF
VPOS
AD8375
5.1pF
1nF
1µH
3.9pF
301Ω
1nF
S
Figure 49. Differential Input Configuration Using the AD8375
R3
R1
P
R2
VIN+
C1
0.1µF
68nH
1000pF
NOTES
1. ALL INDUCTORS ARE COILCRAFT® 0603CS COMPONENTS WITH THE
EXCEPTION OF THE 1µH CHOKE INDUCTORS (COIL CRAFT 0603LS).
2. FILTER VALUES SHOWN ARE FOR A 20MHz BANDWIDTH FILTER
CENTERED AT 140MHz.
0.1µF
S
2.5kΩ║2pF
180nH 220nH
33Ω
PA
AD9642
VCM
165Ω
C2
2V p-p
R3
Shunt
(Ω)
49.9
49.9
180nH 220nH
1µH
In the double balun and transformer configurations, the value
of the input capacitors and resistors is dependent on the input
frequency and source impedance. Based on these parameters,
the value of the input resistors and capacitors may need to be
0.1µF
C2
Shunt
(pF)
15
8.2
An alternative to using a transformer-coupled input at
frequencies in the second Nyquist zone is to use an amplifier
with variable gain. The AD8375 digital variable gain amplifier
(DVGA) provides good performance for driving the AD9642.
Figure 49 shows an example of the AD8375 driving the AD9642
through a band-pass antialiasing filter.
Figure 48. Differential Transformer-Coupled Configuration
33Ω
ADC
0.1µF
R1
R2
R3
C2
Figure 50. Differential Double Balun Input Configuration
Rev. B | Page 18 of 28
VIN–
VCM
0.1µF
09995-047
2V p-p
09995-046
R3
Data Sheet
AD9642
VOLTAGE REFERENCE
CLOCK
INPUT
25Ω
390pF
CLK+
390pF
1nF
CLK–
SCHOTTKY
DIODES:
HSMS2822
25Ω
CLOCK INPUT CONSIDERATIONS
For optimum performance, the AD9642 sample clock inputs,
CLK+ and CLK−, should be clocked with a differential signal.
The signal is typically ac-coupled into the CLK+ and CLK− pins
via a transformer or via capacitors. These pins are biased internally
(see Figure 51) and require no external bias. If the inputs are
floated, the CLK− pin is pulled low to prevent spurious clocking.
AVDD
ADC
390pF
09995-057
A stable and accurate voltage reference is built into the AD9642.
The full-scale input range can be adjusted by varying the reference
voltage via SPI. The input span of the ADC tracks reference voltage
changes linearly.
Figure 53. Balun-Coupled Differential Clock (Up to 625 MHz)
If a low jitter clock source is not available, another option is to
ac-couple a differential PECL signal to the sample clock input
pins as shown in Figure 54. The AD9510, AD9511, AD9512,
AD9513, AD9514, AD9515, AD9516, AD9517, AD9518, AD9520,
AD9522, AD9523, AD9524, and ADCLK905/ADCLK907/
ADCLK925 clock drivers offer excellent jitter performance.
0.9V
0.1µF
Figure 51. Simplified Equivalent Clock Input Circuit
The AD9642 has a very flexible clock input structure. Clock input
can be a CMOS, LVDS, LVPECL, or sine wave signal. Regardless
of the type of signal being used, clock source jitter is of the most
concern, as described in the Jitter Considerations section.
Figure 52 and Figure 53 show two preferable methods for
clocking the AD9642 (at clock rates of up to 625 MHz). A low
jitter clock source is converted from a single-ended signal to a
differential signal using an RF balun or RF transformer.
390pF
50Ω
ADC
AD9642
240Ω
A third option is to ac-couple a differential LVDS signal to the
sample clock input pins, as shown in Figure 55. The AD9510,
AD9511, AD9512, AD9513, AD9514, AD9515, AD9516, AD9517,
AD9518, AD9520, AD9522, AD9523, and AD9524 clock drivers
offer excellent jitter performance.
0.1µF
CLK+
AD95xx
0.1µF
CLOCK
INPUT
LVDS DRIVER
100Ω
0.1µF
ADC
AD9642
CLK–
50kΩ
50kΩ
Figure 55. Differential LVDS Sample Clock (Up to 625 MHz)
Input Clock Divider
The AD9642 contains an input clock divider with the ability to
divide the input clock by integer values between 1 and 8. The
duty cycle stabilizer (DCS) is enabled by default on power-up.
Clock Duty Cycle
Typical high speed ADCs use both clock edges to generate a
variety of internal timing signals and, as a result, may be
sensitive to clock duty cycle. Commonly, a ±5% tolerance is
required on the clock duty cycle to maintain dynamic
performance characteristics.
ADC
100Ω
390pF
09995-056
CLK–
Figure 52. Transformer-Coupled Differential Clock (Up to 200 MHz)
240Ω
50kΩ
0.1µF
CLK+
SCHOTTKY
DIODES:
HSMS2822
100Ω
0.1µF
CLK–
50kΩ
CLOCK
INPUT
The RF balun configuration is recommended for clock
frequencies between 125 MHz and 625 MHz, and the RF
transformer is recommended for clock frequencies from
10 MHz to 200 MHz. The back-to-back Schottky diodes across
the secondary winding of the transformer limit clock excursions
into the AD9642 to approximately 0.8 V p-p differential. This
limit helps prevent the large voltage swings of the clock from
feeding through to other portions of the AD9642 while
preserving the fast rise and fall times of the signal, which are
critical for low jitter performance.
CLOCK
INPUT
PECL DRIVER
Figure 54. Differential PECL Sample Clock (Up to 625 MHz)
Clock Input Options
Mini-Circuits®
ADT1-1WT, 1:1Z
390pF
XFMR
AD95xx,
ADCLK9xx
09995-051
CLOCK
INPUT
0.1µF
CLK+
4pF
09995-048
4pF
0.1µF
CLOCK
INPUT
CLK–
09995-052
CLK+
The AD9642 contains a DCS that retimes the nonsampling
(falling) edge, providing an internal clock signal with a nominal
50% duty cycle. This allows the user to provide a wide range of
clock input duty cycles without affecting the performance of the
AD9642.
Rev. B | Page 19 of 28
AD9642
Data Sheet
0.20
0.3
TOTAL POWER
0.15
IAVDD
0.2
0.10
0.1
0
40
55
70
0
85 100 115 130 145 160 175 190 205 220 235 250
ENCODE FREQUENCY (MSPS)
In the equation, the rms aperture jitter represents the rootmean-square of all jitter sources, which include the clock input,
the analog input signal, and the ADC aperture jitter specification.
IF undersampling applications are particularly sensitive to jitter,
as shown in Figure 56.
80
Figure 57. AD9642-250 Power and Current vs. Sample Rate
By setting the internal power-down mode bits (Bits[1:0]) in the
power modes register (Address 0x08) to 01, the AD9642 is
placed in power-down mode. In this state, the ADC typically
dissipates 2.5 mW. During power-down, the output drivers are
placed in a high impedance state.
Low power dissipation in power-down mode is achieved by
shutting down the reference, reference buffer, biasing networks,
and clock. Internal capacitors are discharged when entering
power-down mode and then must be recharged when returning
to normal operation. As a result, the wake-up time is related to
the time spent in power-down mode, and shorter power-down
cycles result in proportionally shorter wake-up times.
75
70
SNR (dBFS)
IDRVDD
0.05
SNRHF = −10 log[(2π × fIN × tJRMS)2 + 10 (SNRLF /10) ]
65
60
1
10
100
1000
INPUT FREQUENCY (MHz)
09995-061
0.05ps
0.2ps
0.5ps
1ps
1.5ps
MEASURED
55
50
0.25
0.4
SNR/SFDR (dBc and dBFS)
High speed, high resolution ADCs are sensitive to the quality of
the clock input. The degradation in SNR at a given input
frequency (fIN) due to jitter (tJ) can be calculated by
As shown in Figure 57, the power dissipated by the AD9642 is
proportional to its sample rate. The data in Figure 57 was taken
using the same operating conditions as those used for the
Typical Performance Characteristics section.
09995-060
Jitter Considerations
POWER DISSIPATION AND STANDBY MODE
TOTAL POWER (W)
Jitter on the rising edge of the input clock is still of paramount
concern and is not reduced by the duty cycle stabilizer. The duty
cycle control loop does not function for clock rates less than
40 MHz nominally. The loop has a time constant associated
with it that must be considered when the clock rate may change
dynamically. A wait time of 1.5 μs to 5 μs is required after a
dynamic clock frequency increase or decrease before the DCS
loop is relocked to the input signal. During the time that the loop
is not locked, the DCS loop is bypassed, and internal device timing
is dependent on the duty cycle of the input clock signal. In such
applications, it may be appropriate to disable the duty cycle
stabilizer. In all other applications, enabling the DCS circuit is
recommended to maximize ac performance.
Figure 56. AD9642-250 SNR vs. Input Frequency and Jitter
In cases where aperture jitter may affect the dynamic range of the
AD9642, treat the clock input as an analog signal. In addition,
use separate power supplies for the clock drivers and the ADC
output driver to avoid modulating the clock signal with digital
noise. Low jitter, crystal controlled oscillators provide the best
clock sources. If the clock is generated from another type of source
(by gating, dividing, or another method), it should be retimed
by the original clock during the last step.
Refer to the AN-501 Application Note, Aperture Uncertainty and
ADC System Performance, and the AN-756 Application Note,
Sampled Systems and the Effects of Clock Phase Noise and Jitter, for
more information about jitter performance as it relates to ADCs.
When using the SPI port interface, the user can place the ADC
in power-down mode or standby mode. Standby mode allows
the user to keep the internal reference circuitry powered when
faster wake-up times are required. To put the part into standby
mode, set the internal power-down mode bits (Bits[1:0]) in the
power modes register (Address 0x08) to 10. See the Memory
Map section and the AN-877 Application Note, Interfacing to
High Speed ADCs via SPI, for additional details.
DIGITAL OUTPUTS
The AD9642 output drivers can be configured for either ANSI
LVDS or reduced swing LVDS using a 1.8 V DRVDD supply.
As detailed in the AN-877 Application Note, Interfacing to High
Speed ADCs via SPI, the data format can be selected for offset
binary, twos complement, or gray code when using the SPI control.
Digital Output Enable Function (OEB)
The AD9642 has a flexible three-state ability for the digital
output pins. The three-state mode is enabled using the SPI
interface. The data outputs can be three-stated by using the
output enable bar bit (Bit 4) in Register 0x14. This OEB
function is not intended for rapid access to the data bus.
Rev. B | Page 20 of 28
Data Sheet
AD9642
Timing
The lowest typical conversion rate of the AD9642 is 40 MSPS.
At clock rates below 40 MSPS, dynamic performance may
degrade.
The AD9642 provides latched data with a pipeline delay of
10 input sample clock cycles. Data outputs are available one
propagation delay (tPD) after the rising edge of the clock signal.
Data Clock Output (DCO)
Minimize the length of the output data lines as well as the loads
placed on these lines to reduce transients within the AD9642.
These transients may degrade converter dynamic performance.
The AD9642 also provides the data clock output (DCO) intended
for capturing the data in an external register. Figure 2 shows a
timing diagram of the AD9642 output modes.
Table 10. Output Data Format
Input (V)
VIN+ − VIN−
VIN+ − VIN−
VIN+ − VIN−
VIN+ − VIN−
VIN+ − VIN−
VIN+ − VIN−,
Input Span = 1.75 V p-p (V)
<–0.875
−0.875
0
+0.875
>+0.875
Offset Binary Output Mode
00 0000 0000 0000
00 0000 0000 0000
10 0000 0000 0000
11 1111 1111 1111
11 1111 1111 1111
Rev. B | Page 21 of 28
Twos Complement Mode (Default)
10 0000 0000 0000
10 0000 0000 0000
00 0000 0000 0000
01 1111 1111 1111
01 1111 1111 1111
AD9642
Data Sheet
SERIAL PORT INTERFACE (SPI)
The AD9642 serial port interface (SPI) allows the user to
configure the converter for specific functions or operations
through a structured register space provided inside the ADC.
The SPI offers added flexibility and customization, depending
on the application. Addresses are accessed via the serial port
and can be written to or read from via the port. Memory is
organized into bytes that can be further divided into fields.
These fields are documented in the Memory Map section. For
detailed operational information, see the AN-877 Application
Note, Interfacing to High Speed ADCs via SPI.
CONFIGURATION USING THE SPI
Three pins define the SPI of this ADC: the SCLK pin, the SDIO pin,
and the CSB pin (see Table 11). The SCLK (serial clock) pin is
used to synchronize the read and write data presented from and
to the ADC. The SDIO (serial data input/output) pin is a dualpurpose pin that allows data to be sent and read from the internal
ADC memory map registers. The CSB (chip select bar) pin is an
active low control that enables or disables the read and write cycles.
Table 11. Serial Port Interface Pins
Pin
SCLK
SDIO
CSB
Function
Serial clock. The serial shift clock input, which is used to
synchronize serial interface reads and writes.
Serial data input/output. A dual-purpose pin that
typically serves as an input or an output, depending on
the instruction being sent and the relative position in the
timing frame.
Chip select bar. An active low control that gates the read
and write cycles.
The falling edge of CSB, in conjunction with the rising edge of
SCLK, determines the start of the framing. An example of the
serial timing and its definitions can be found in Figure 58 and
Table 5.
Other modes involving the CSB are available. The CSB can be
held low indefinitely, which permanently enables the device;
this is called streaming. The CSB can stall high between bytes
to allow for additional external timing. When CSB is tied high,
SPI functions are placed in a high impedance mode. This mode
turns on any SPI pin secondary functions.
All data is composed of 8-bit words. The first bit of each
individual byte of serial data indicates whether a read or write
command is issued. This allows the serial data input/output
(SDIO) pin to change direction from an input to an output.
In addition to word length, the instruction phase determines
whether the serial frame is a read or write operation, allowing
the serial port to be used both to program the chip and to read the
contents of the on-chip memory. If the instruction is a readback
operation, performing a readback causes the serial data input/
output (SDIO) pin to change direction from an input to an output
at the appropriate point in the serial frame.
Data can be sent in MSB first mode or in LSB first mode. MSB first
mode is the default on power-up and can be changed via the SPI
port configuration register. For more information about this and
other features, see the AN-877 Application Note, Interfacing to
High Speed ADCs via SPI.
HARDWARE INTERFACE
The pins described in Table 11 comprise the physical interface
between the user programming device and the serial port of the
AD9642. The SCLK pin and the CSB pin function as inputs
when using the SPI interface. The SDIO pin is bidirectional,
functioning as an input during write phases and as an output
during readback.
The SPI interface is flexible enough to be controlled by either
FPGAs or microcontrollers. One method for SPI configuration
is described in detail in the AN-812 Application Note, Microcontroller-Based Serial Port Interface (SPI) Boot Circuit.
The SPI port should not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK signal, the CSB signal, and the SDIO signal are typically
asynchronous to the ADC clock, noise from these signals can
degrade converter performance. If the on-board SPI bus is used for
other devices, it may be necessary to provide buffers between
this bus and the AD9642 to prevent these signals from transitioning at the converter inputs during critical sampling periods.
During an instruction phase, a 16-bit instruction is transmitted.
Data follows the instruction phase, and its length is determined
by the W0 and W1 bits.
Rev. B | Page 22 of 28
Data Sheet
AD9642
SPI ACCESSIBLE FEATURES
Table 12 provides a brief description of the general features that
are accessible via the SPI. These features are described in detail
in the AN-877 Application Note, Interfacing to High Speed
ADCs via SPI.
Table 12. Features Accessible Using the SPI
Feature Name
Mode
Clock
Offset
Test I/O
Output Mode
Output Phase
Output Delay
VREF
Digital Processing
Description
Allows the user to set either power-down mode or standby mode
Allows the user to access the DCS via the SPI
Allows the user to digitally adjust the converter offset
Allows the user to set test modes to have known data on output bits
Allows the user to set up outputs
Allows the user to set the output clock polarity
Allows the user to vary the DCO delay
Allows the user to set the reference voltage
Allows the user to enable the synchronization features
tHIGH
tDS
tS
tDH
tCLK
tH
tLOW
CSB
DON’T
CARE
SDIO
DON’T
CARE
DON’T
CARE
R/W
W1
W0
A12
A11
A10
A9
A8
A7
D5
Figure 58. Serial Port Interface Timing Diagram
Rev. B | Page 23 of 28
D4
D3
D2
D1
D0
DON’T
CARE
09995-055
SCLK
AD9642
Data Sheet
MEMORY MAP
READING THE MEMORY MAP REGISTER TABLE
Each row in the memory map register table has eight bit locations.
The memory map is roughly divided into three sections: the
chip configuration registers (Address 0x00 to Address 0x02); the
transfer register (Address 0xFF); and the ADC functions registers,
including setup, control, and test (Address 0x08 to Address 0x20).
The memory map register table (Table 13) documents the
default hexadecimal value for each hexadecimal address shown.
The Bit 7 (MSB) column is the start of the default hexadecimal
value given. For example, Address 0x14, the output mode register,
has a hexadecimal default value of 0x01. This means that Bit 0 = 1
and the remaining bits are 0s. This setting is the default output
format value, which is twos complement. For more information
on this function and others, see the AN-877 Application Note,
Interfacing to High Speed ADCs via SPI. This document details
the functions controlled by Register 0x00 to Register 0x20.
Open Locations
All address and bit locations that are not included in Table 13 are
not currently supported for this device. Write 0s to unused bits
of a valid address location. Writing to these locations is required
only when part of an address location is open (for example,
Address 0x18). If the entire address location is open (for example,
Address 0x13), this address location should not be written.
Default Values
After the AD9642 is reset, critical registers are loaded with
default values. The default values for the registers are given in
the memory map register table (Table 13).
Logic Levels
An explanation of logic level terminology follows:
•
•
“Bit is set” is synonymous with “bit is set to Logic 1” or
“writing Logic 1 for the bit.”
“Clear a bit” is synonymous with “bit is set to Logic 0” or
“writing Logic 0 for the bit.”
Transfer Register Map
Address 0x08 to Address 0x20 are shadowed. Writes to these
addresses do not affect part operation until a transfer command
is issued by writing 0x01 to Address 0xFF, setting the transfer
bit. This allows these registers to be updated internally and
simultaneously when the transfer bit is set. The internal update
takes place when the transfer bit is set, and then the bit autoclears.
Rev. B | Page 24 of 28
Data Sheet
AD9642
MEMORY MAP REGISTER TABLE
All address and bit locations that are not included in Table 13 are not currently supported for this device.
Table 13. Memory Map Registers
Addr
Register
Bit 7
(Hex)
Name
(MSB)
Chip Configuration Registers
0x00
SPI port
0
configuration
0x01
Chip ID
0x02
Chip grade
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
(LSB)
LSB first
Soft reset
1
1
Soft reset
LSB first
0
8-bit chip ID[7:0]
(AD9642 = 0x86)
(default)
Speed grade ID
Open
00 = 250 MSPS
01 = 210 MSPS
11 = 170 MSPS
Open
Open
Transfer Register
0xFF
Transfer
Open
Open
Open
Open
ADC Functions Registers
0x08
Power modes
Open
Open
Open
0x09
Global clock
Open
Open
Open
0x0B
Clock divide
Open
Open
0x0D
Test mode
User test
mode
control
0 = continuous/
repeat
pattern
1 = single
pattern,
then 0s
Open
Reset PN
long gen
Open
Open
Open
Open
Open
Transfer
Open
Open
Open
Open
Open
Open
Reset PN
short gen
Rev. B | Page 25 of 28
Default
Notes/
Comments
0x18
Nibbles
are mirrored
so that LSB
first mode
or MSB first
mode is set
correctly,
regardless
of shift
mode.
Read only.
0x86
Open
Input clock divider phase adjust
000 = no delay
001 = 1 input clock cycle
010 = 2 input clock cycles
011 = 3 input clock cycles
100 = 4 input clock cycles
101 = 5 input clock cycles
110 = 6 input clock cycles
111 = 7 input clock cycles
Default
Value
(Hex)
Speed
grade ID
used to
differentiate
devices;
read only.
0x00
Synchronously
transfers
data from
the master
shift register
to the slave.
Internal power-down mode
00 = normal operation
01 = full power-down
10 = standby
11 = reserved
0x00
Determines
various
generic
modes
of chip
operation.
Open
0x01
Duty cycle
stabilizer
(default)
Clock divide ratio
000 = divide by 1
001 = divide by 2
010 = divide by 3
011 = divide by 4
100 = divide by 5
101 = divide by 6
110 = divide by 7
111 = divide by 8
Output test mode
0000 = off (default)
0001 = midscale short
0010 = positive FS
0011 = negative FS
0100 = alternating checkerboard
0101 = PN long sequence
0110 = PN short sequence
0111 = one/zero word toggle
1000 = user test mode
1001 to 1110 = unused
1111 = ramp output
0x00
0x00
Clock
divide
values
other than
000 automatically
cause the
duty cycle
stabilizer to
become
active.
When this
register is
set, the test
data is
placed on
the output
pins in place
of normal
data.
AD9642
Data Sheet
Addr
(Hex)
0x10
Register
Name
Offset adjust
Bit 7
(MSB)
Open
Bit 6
Open
Bit 5
0x14
Output mode
Open
Open
Open
0x15
Output adjust
Open
Open
Open
Open
0x16
Clock phase
control
Invert
DCO clock
Open
Open
Open
0x17
DCO output
delay
Enable
DCO
clock
delay
Open
Open
0x18
Input span
select
Open
Open
Open
0x19
User Test
Pattern 1 LSB
User Test
Pattern 1 MSB
User Test
Pattern 2 LSB
User Test
Pattern 2 MSB
User Test
Pattern 3 LSB
User Test
Pattern 3 MSB
User Test
Pattern 4 LSB
User Test
Pattern 4 MSB
0x1A
0x1B
0x1C
0x1D
0x1E
0x1F
0x20
Bit 0
(LSB)
Bit 4
Bit 3
Bit 2
Bit 1
Offset adjust in LSBs from +31 to −32
(twos complement format)
Output
Open
Output
Output format
enable bar
invert
00 = offset binary
0 = normal
01 = twos complement
(default)
(default)
0 = on
(default)
10 = gray code
1 = inverted
11 = reserved
1 = off
LVDS output drive current adjust
0000 = 3.72 mA output drive current
0001 = 3.5 mA output drive current (default)
0010 = 3.30 mA output drive current
0011 = 2.96 mA output drive current
0100 = 2.82 mA output drive current
0101 = 2.57 mA output drive current
0110 = 2.27 mA output drive current
0111 = 2.0 mA output drive current (reduced range)
1000 to 1111 = reserved
Open
Open
Open
Open
Default
Value
(Hex)
0x00
Default
Notes/
Comments
0x01
Configures
the outputs
and the
format of
the data.
0x01
0x00
DCO clock delay
[delay = (3100 ps × register value/31 + 100)]
00000 = 100 ps
00001 = 200 ps
00010 = 300 ps
…
11110 = 3100 ps
11111 = 3200 ps
Full-scale input voltage selection
01111 = 2.087 V p-p
…
00001 = 1.772 V p-p
00000 = 1.75 V p-p (default)
11111 = 1.727 V p-p
…
10000 = 1.383 V p-p
User Test Pattern 1[7:0]
0x00
User Test Pattern 1[15:8]
0x00
User Test Pattern 2[7:0]
0x00
User Test Pattern 2[15:8]
0x00
User Test Pattern 3[7:0]
0x00
User Test Pattern 3[15:8]
0x00
User Test Pattern 4[7:0]
0x00
User Test Pattern 4[15:8]
0x00
Rev. B | Page 26 of 28
0x00
0x00
Full-scale
input
adjustment
in 0.022 V
steps.
Data Sheet
AD9642
APPLICATIONS INFORMATION
VCM
DESIGN GUIDELINES
Before starting system level design and layout of the AD9642,
it is recommended that the designer become familiar with these
guidelines, which discuss the special circuit connections and
layout requirements for certain pins.
Power and Ground Recommendations
When connecting power to the AD9642, it is recommended that
two separate 1.8 V supplies be used: use one supply for analog
(AVDD) and a separate supply for the digital outputs (DRVDD).
The designer can employ several different decoupling capacitors
to cover both high and low frequencies. Locate these capacitors
close to the point of entry at the PC board level and close to the
pins of the part with minimal trace length.
Decouple the VCM pin to ground with a 0.1 μF capacitor, as
shown in Figure 48.
SPI Port
The SPI port should not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK, CSB, and SDIO signals are typically asynchronous to the
ADC clock, noise from these signals can degrade converter
performance. If the on-board SPI bus is used for other devices,
it may be necessary to provide buffers between this bus and the
AD9642 to keep these signals from transitioning at the
converter input pins during critical sampling periods.
A single PCB ground plane should be sufficient when using the
AD9642. With proper decoupling and smart partitioning of the
PCB analog, digital, and clock sections, optimum performance
can be easily achieved.
Exposed Paddle Thermal Heat Slug Recommendations
It is mandatory that the exposed paddle on the underside of the
ADC be connected to analog ground (AGND) to achieve the
best electrical and thermal performance. A continuous, exposed
(no solder mask) copper plane on the PCB should mate to the
AD9642 exposed paddle, Pin 0.
The copper plane should have several vias to achieve the lowest
possible resistive thermal path for heat dissipation to flow
through the bottom of the PCB. These vias should be filled or
plugged with nonconductive epoxy.
To maximize the coverage and adhesion between the ADC
and the PCB, overlay a silkscreen to partition the continuous
plane on the PCB into several uniform sections. This provides
several tie points between the ADC and the PCB during the
reflow process. Using one continuous plane with no partitions
guarantees only one tie point between the ADC and the PCB.
See the evaluation board for a PCB layout example. For detailed
information about the packaging and PCB layout of chip scale
packages, refer to the AN-772 Application Note, A Design and
Manufacturing Guide for the Lead Frame Chip Scale Package
(LFCSP).
Rev. B | Page 27 of 28
AD9642
Data Sheet
OUTLINE DIMENSIONS
0.30
0.25
0.18
32
25
1
24
0.50
BSC
*3.75
3.60 SQ
3.55
EXPOSED
PAD
17
TOP VIEW
0.80
0.75
0.70
0.50
0.40
0.30
8
16
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
PIN 1
INDICATOR
9
BOTTOM VIEW
0.25 MIN
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
*COMPLIANT TO JEDEC STANDARDS MO-220-WHHD-5
WITH THE EXCEPTION OF THE EXPOSED PAD DIMENSION.
08-16-2010-B
PIN 1
INDICATOR
5.10
5.00 SQ
4.90
Figure 59. 32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
5 mm × 5 mm Body, Very Thin Quad
(CP-32-12)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
AD9642BCPZ-170
AD9642BCPZ-210
AD9642BCPZ-250
AD9642BCPZRL7-170
AD9642BCPZRL7-210
AD9642BCPZRL7-250
AD9642-170EBZ
AD9642-210EBZ
AD9642-250EBZ
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
Evaluation Board with AD9642 and Software
Evaluation Board with AD9642 and Software
Evaluation Board with AD9642 and Software
Z = RoHS Compliant Part.
©2011–2015 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D09995-0-1/15(B)
Rev. B | Page 28 of 28
Package Option
CP-32-12
CP-32-12
CP-32-12
CP-32-12
CP-32-12
CP-32-12