FERROXCUBE DATA SHEET E58/11/38 Planar E cores and accessories Supersedes data of September 2004 2008 Sep 01 Ferroxcube Planar E cores and accessories E58/11/38 CORES Effective core parameters of a set of E cores SYMBOL PARAMETER VALUE Σ(I/A) core factor (C1) 0.268 mm−1 Ve effective volume 24600 mm3 Ie effective length 80.6 mm Ae effective area 308 mm2 Amin minimum area 308 mm2 m mass of core half ≈ 62 g 58.4 ±1.2 handbook, halfpage UNIT 50 min. 8.1 ±0.2 6.5 ±0.13 10.5 ±0.13 38.1 ± 0.8 R0.64 ref. typ. R0.81 ref. typ. CBW413 Dimensions in mm. Fig.1 E58/11/38 core half. Effective core parameters of an E/PLT combination SYMBOL PARAMETER VALUE UNIT Σ(I/A) core factor (C1) 0.224 mm−1 Ve effective volume 20800 mm3 Ie effective length 67.7 mm Ae effective area 310 mm2 Amin minimum area 310 mm2 m mass of core half ≈ 44 g handbook, halfpage 58.4 ±1.2 4.1 ±0.13 Ordering information for plates GRADE 38.1 ±0.8 TYPE NUMBER 3C90 PLT58/38/4-3C90 3C92 PLT58/38/4-3C92 3C93 PLT58/38/4-3C93 3C94 PLT58/38/4-3C94 3C95 PLT58/38/4-3C95 3F3 PLT58/38/4-3F3 3F4 PLT58/38/4-3F4 CBW414 R0.64 ref. typ. Dimensions in mm. Fig.2 PLT 58/38/4. 2008 Sep 01 2 Ferroxcube Planar E cores and accessories E58/11/38 Core halves for use in combination with an E core AL measured in combination with a non-gapped core half, clamping force for AL measurements, 40 ±20 N, unless stated otherwise. GRADE 3C90 AL (nH) TOTAL AIR GAP (µm) µe TYPE NUMBER 315 ±3%(1) ≈ 67 ≈ 1400 E58/11/38-3C90-E315-E 400 ±3%(1) ≈ 85 ≈ 1100 E58/11/38-3C90-E400-E 630 ±5%(1) ≈ 134 ≈ 650 E58/11/38-3C90-E630-E 1000 ±5% ≈ 213 ≈ 400 E58/11/38-3C90-A1000-E 1600 ±10% ≈ 341 ≈ 200 E58/11/38-3C90-A1600-E 8480 ±25% ≈ 1800 ≈0 E58/11/38-3C90 3C92 6600 ±25% ≈ 1410 ≈0 E58/11/38-3C92 3C93 7710 ±25% ≈ 1640 ≈0 E58/11/38-3C93 3C94 315 ±3%(1) ≈ 67 ≈ 1400 400 ±3%(1) ≈ 85 ≈ 1100 E58/11/38-3C94-E400-E 630 ±5%(1) ≈ 134 ≈ 650 E58/11/38-3C94-E630-E ≈ 213 ≈ 400 E58/11/38-3C94-A1000-E E58/11/38-3C94-A1600-E 1000 ±5% 3C95 3F3 1600 ±10% ≈ 341 ≈ 200 8480 ±25% ≈ 1800 ≈0 E58/11/38-3C94 10330 ±25% E58/11/38-3C95 ≈ 2150 ≈0 ±3%(1) ≈ 67 ≈ 1400 E58/11/38-3F3-E315-E 400 ±3%(1) ≈ 85 ≈ 1100 E58/11/38-3F3-E400-E ±5%(1) ≈ 134 ≈ 650 E58/11/38-3F3-E630-E ≈ 213 ≈ 400 E58/11/38-3F3-A1000-E 1600 ±10% ≈ 341 ≈ 200 E58/11/38-3F3-A1600-E 7710 ±25% ≈ 1640 ≈0 315 630 1000 ±5% 3F4 E58/11/38-3C94-E315-E E58/11/38-3F3 315 ±3%(1) ≈ 67 ≈ 1400 400 ±3%(1) ≈ 85 ≈ 1100 E58/11/38-3F4-E400-E 630 ±5%(1) ≈ 134 ≈ 650 E58/11/38-3F4-E630-E ≈ 213 ≈ 400 E58/11/38-3F4-A1000-E 1600 ±10% ≈ 341 ≈ 200 E58/11/38-3F4-A1600-E 4030 ±25% ≈ 860 ≈0 1000 ±5% E58/11/38-3F4-E315-E E58/11/38-3F4 Note 1. Measured in combination with an equal gapped E core half, clamping force for AL measurements, 40 ±20 N. 2008 Sep 01 3 Ferroxcube Planar E cores and accessories E58/11/38 Core halves for use in combination with a plate (PLT) AL measured in combination with a plate (PLT), clamping force for AL measurements, 40 ±20 N. GRADE 3C90 AL (nH) AIR GAP (µm) µe TYPE NUMBER 315 ±3% ≈ 56 ≈ 1400 E58/11/38-3C90-A315-P 400 ±3% ≈ 71 ≈ 1100 E58/11/38-3C90-A400-P 630 ±5% ≈ 112 ≈ 650 E58/11/38-3C90-A630-P 1000 ±5% ≈ 178 ≈ 400 E58/11/38-3C90-A1000-P 1600 ±10% ≈ 285 ≈ 200 E58/11/38-3C90-A1600-P 9970 ±25% ≈ 1780 ≈0 E58/11/38-3C90 3C92 7770 ±25% ≈ 1390 ≈0 E58/11/38-3C92 3C93 9070 ±25% ≈ 1620 ≈0 E58/11/38-3C93 3C94 315 ±3% ≈ 56 ≈ 1400 E58/11/38-3C94-A315-P 400 ±3% ≈ 71 ≈ 1100 E58/11/38-3C94-A400-P 630 ±5% ≈ 112 ≈ 650 E58/11/38-3C94-A630-P 1000 ±5% ≈ 178 ≈ 400 E58/11/38-3C94-A1000-P E58/11/38-3C94-A1600-P 3C95 3F3 3F4 2008 Sep 01 1600 ±10% ≈ 285 ≈ 200 9970 ±25% ≈ 1780 ≈0 E58/11/38-3C94 12090 ±25% ≈ 2100 ≈0 E58/11/38-3C95 ≈ 56 ≈ 1400 E58/11/38-3F3-A315-P 400 ±3% ≈ 71 ≈ 1100 E58/11/38-3F3-A400-P 630 ±5% ≈ 112 ≈ 650 E58/11/38-3F3-A630-P 1000 ±5% ≈ 178 ≈ 400 E58/11/38-3F3-A1000-P 1600 ±10% ≈ 285 ≈ 200 E58/11/38-3F3-A1600-P 9070 ±25% ≈ 1620 ≈0 ≈ 56 ≈ 1400 E58/11/38-3F4-A315-P 400 ±3% ≈ 71 ≈ 1100 E58/11/38-3F4-A400-P 630 ±5% ≈ 112 ≈ 650 E58/11/38-3F4-A630-P 1000 ±5% ≈ 178 ≈ 400 E58/11/38-3F4-A1000-P 1600 ±10% ≈ 285 ≈ 200 E58/11/38-3F4-A1600-P 4780 ±25% ≈ 850 ≈0 315 ±3% 315 ±3% 4 E58/11/38-3F3 E58/11/38-3F4 Ferroxcube Planar E cores and accessories E58/11/38 Properties of core sets under power conditions B (mT) at GRADE H = 250 A/m; f = 10 kHz; T = 100 °C CORE LOSS (W) at f = 100 kHz; ˆ = 100 mT; B T = 100 °C f = 100 kHz; ˆ = 200 mT; B T = 25 °C f = 100 kHz; ˆ = 200 mT; B T = 100 °C f = 400 kHz; ˆ = 50 mT; B T = 100 °C E+E58-3C90 ≥320 ≤ 3.0 − − − E+PLT58-3C90 ≥320 ≤ 2.6 − − − E+E58-3C92 ≥370 ≤ 2.4 − ≤ 15 − E+PLT58-3C92 ≥370 ≤ 2.0 − ≤ 13 − E+E58-3C93 ≥320 ≤ 2.4(1) − ≤ 15(1) − E+PLT58-3C93 ≥320 ≤ − ≤ − E+E58-3C94 ≥320 ≤ 2.4 − ≤ 15 − E+PLT58-3C94 ≥320 ≤ 2.0 − ≤ 13 − E+E58-3C95 ≥320 − ≤ 15.5 ≤ 14.8 − E+PLT58-3C95 ≥320 − ≤ 13.1 ≤ 12.5 − E+E58-3F3 ≥300 ≤ 3.0 − − ≤ 4.7 E+PLT58-3F3 ≥300 ≤ 2.6 − − ≤ 4.0 E+E58-3F4 ≥250 − − − − E+PLT58-3F4 ≥250 − − − − 1. 2.0(1) 13(1) Measured at 140 °C. Properties of core sets under power conditions (continued) B (mT) at GRADE H = 250 A/m; f = 10 kHz; T = 100 °C CORE LOSS (W) at f = 500 kHz; ˆ = 50 mT; B T = 100 °C f = 500 kHz; ˆ = 100 mT; B T = 100 °C f = 1 MHz; ˆ = 30 mT; B T = 100 °C f = 3 MHz; ˆ = 10 mT; B T = 100 °C E+E58-3F4 ≥250 − − ≤ 7.4 ≤ 12 E+PLT58-3F4 ≥250 − − ≤ 6.25 ≤ 10 2008 Sep 01 5 Ferroxcube Planar E cores and accessories E58/11/38 DATA SHEET STATUS DEFINITIONS DATA SHEET STATUS PRODUCT STATUS DEFINITIONS Preliminary specification Development This data sheet contains preliminary data. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Product specification Production This data sheet contains final specifications. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. DISCLAIMER Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Ferroxcube customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Ferroxcube for any damages resulting from such application. PRODUCT STATUS DEFINITIONS STATUS INDICATION DEFINITION Prototype These are products that have been made as development samples for the purposes of technical evaluation only. The data for these types is provisional and is subject to change. Design-in These products are recommended for new designs. Preferred These products are recommended for use in current designs and are available via our sales channels. Support These products are not recommended for new designs and may not be available through all of our sales channels. Customers are advised to check for availability. 2008 Sep 01 6