Wing LS1240AD1 Electronic two-tone ringer Datasheet

LS1240A
.
.
..
.
Electronic Two-Tone Ringer
LOW CURRENT CONSUMPTION, IN ORDER
TO ALLOW THE PARALLEL OPERATION OF 4
DEVICES
INTEGRATED RECTIFIER BRIDGE WITH
ZENER DIODES TO PROTECT AGAINST
OVERVOLTAGES
LITTLE EXTERNAL CIRCUITRY
TONE AND SWITCHING FREQUENCIES ADJUSTABLE BY EXTERNAL COMPONENTS
INTEGRATED VOLTAGE AND CURRENT
HYSTERESIS
DESCRIPTION
LS1240A is a monolithic integrated circuit designed
to replace the mechanical bell in telephone sets in
connection with an electro-acoustical converter. It
can drive directly a piezoceramic converter (buzzer)or a dynamic loudspeaker.
The output current capability of LS1240A is higher
than standard ringer. For driving a dynamic loudspeaker LS1240A can simply use a decoupling capacitor, thus eliminating the usual transformer.
No current limitation is provided on the output stage
of LS1240A, so a minimum load DC of 50 Ω is adviced, in series with a proper capacitor.
The two tone frequencies generated are switched
by an internal oscillator in a fast sequence and made
audible across an output amplifier in the loudspeaker, both tone frequencies and the switching
frequency can be externally adjusted.
Minidip
SO8
ORDERING NUMBERS
Minidip
LS1240A
The supply voltage is obtained from the AC ring signal and the circuit is designed so that noise on the
line or variations of the ringing signal cannot affect
correct operation of the device.
PIN CONNECTION (top view)
Wing Shing Computer Components Co., (H.K.)Ltd.
Homepage: http://www.wingshing.com
SO8
LS1240AD1
Tel:(852)2341 9276 Fax:(852)2797 8153
E-mail: [email protected]
WS
LS1240A
BLOCK DIAGRAM
Figure 1 : Test Circuit.
R1 =
2.72 ⋅ 104
f1
⋅ ( 1 − 0.04 ln
)
1943
f1 (Hz)
f2 = 0.725 f1
fSWEEP =
750
C1 (nF)
WS
LS1240A
ABSOLUTE MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
VAB
Calling Voltage (f = 50 Hz) Continuous
120
Vrms
VAB
Calling Voltage (f = 50 Hz) 5s ON/10s OFF
200
Vrms
DC
Supply Current
30
mA
Top
Operating Temperature
–20 to + 70
Tstg
Storage and Junction Temperature
– 65 to + 150
°C
Value
Unit
°C
THERMAL DATA
Symbol
Rth j-amb
Parameter
Thermal Resistance Junction-ambient
Max
°C/W
2 00
ELECTRICAL CHARACTERISTICS
(Tamb = 25 °C; Vs = applied between pins 7-2 unless otherwise specified)
Symbol
Parameter
Vs
Supply Voltage
IB
Current Consumption without Load (pins 8-1)
Test Conditions
Min.
V8-1 = 9.3 to 25 V
Typ.
1.5
Max.
V
1.8
mA
V
V
kΩ
V
mA
VON
Activation Voltage
12
13.5
VOFF
Sustaining Voltage
7.8
9.3
Differential Resistance in OFF Condition (pins 8-1)
6.4
RD
VOUT
Output Voltage Swing
IOUT
Short Circuit Current (pins 5-2)
Vs – 5
Vs = 20V
70
RL = 250Ω
Unit
26
AC OPERATION
f1
f2
Output Frequencies
fout1
fout2
Vs = 26V, R1 = 14kΩ
Vs = 0 V
Vs = 6V
fOUT1
fOUT2
Programming Resistor Range
fSWEEP
Sweep Frequency
R1 = 14kΩ, C1 = 100nF
kHz
1.55
1.08
1.33
2.53
1.9
1.43
8
56
kΩ
9.75
Hz
5.25
7.5
WS
LS1240A
Figure 2 : Typical Application with BUZZER
Figure 3 : Typical Application with Loudspeaker (no transformer needed)
C1 such that ZLOAD  > 1 ΚΩ
Similar pages