LINER LT3012BEDE 250ma, 4v to 80v low dropout micropower linear regulator Datasheet

LT3012B
250mA, 4V to 80V
Low Dropout
Micropower Linear Regulator
U
FEATURES
DESCRIPTIO
■
The LT®3012B is a high voltage, micropower low dropout
linear regulator. The device is capable of supplying 250mA
of output current with a dropout voltage of 400mV. Designed for use in battery-powered or high voltage systems, the low quiescent current (40µA operating) makes
the LT3012B an ideal choice. Quiescent current is also well
controlled in dropout.
■
■
■
■
■
■
■
■
■
■
■
Wide Input Voltage Range: 4V to 80V
Low Quiescent Current: 40µA
Low Dropout Voltage: 400mV
Output Current: 250mA
No Protection Diodes Needed
Adjustable Output from 1.24V to 60V
Stable with 3.3µF Output Capacitor
Stable with Aluminum, Tantalum or Ceramic
Capacitors
Reverse-Battery Protection
No Reverse Current Flow from Output to Input
Thermal Limiting
Thermally Enhanced 16-Lead TSSOP and 12-Pin
(4mm × 3mm) DFN Packages
U
APPLICATIO S
■
■
■
■
Low Current High Voltage Regulators
Regulator for Battery-Powered Systems
Telecom Applications
Automotive Applications
Other features of the LT3012B include the ability to operate with very small output capacitors. The regulators are
stable with only 3.3µF on the output while most older
devices require between 10µF and 100µF for stability.
Small ceramic capacitors can be used without any need for
series resistance (ESR) as is common with other regulators. Internal protection circuitry includes reverse-battery
protection, current limiting, thermal limiting and reverse
current protection.
The device is available with an adjustable output with a
1.24V reference voltage. The LT3012B regulator is available in the 16-lead TSSOP and 12 pin low profile (0.75mm)
(4mm × 3mm) DFN packages with an exposed pad for
enhanced thermal handling capability.
, LTC and LT are registered trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
U
TYPICAL APPLICATIO
Dropout Voltage
400
5V Supply
VIN
5.4V TO
80V
VOUT
5V
250mA
OUT
LT3012B
1µF
750k
3.3µF
ADJ
GND
249k
3012B TA01
DROPOUT VOLTAGE (mV)
IN
350
300
250
200
150
100
50
0
0
50
100
150
200
OUTPUT CURRENT (mA)
250
3012B TA02
3012bf
1
LT3012B
W W
W
AXI U
U
ABSOLUTE
RATI GS (Note 1)
IN Pin Voltage ................................................... ±80V
OUT Pin Voltage ............................................... ±60V
IN to OUT Differential Voltage ........................... ±80V
ADJ Pin Voltage .................................................. ±7V
Output Short-Circuit Duration ..................... Indefinite
Storage Temperature Range
TSSOP Package ........................... –65°C to 150°C
DFN Package ............................... –65°C to 125°C
Operating Junction Temperature Range
(Notes 3, 9, 10) ........................... –40°C to 125°C
Lead Temperature (Soldering, 10 sec)............ 300°C
U
U
W
PACKAGE/ORDER I FOR ATIO
TOP VIEW
TOP VIEW
GND
1
16 GND
NC
1
12 NC
NC
2
15 NC
OUT
2
11 IN
OUT
3
14 IN
OUT
3
10 IN
OUT
4
ADJ
4
9
NC
ADJ
5
12 NC
GND
5
8
NC
GND
6
11 NC
NC
6
7
NC
NC
7
10 NC
GND
8
9
13
DE PACKAGE
12-LEAD (4mm × 3mm) PLASTIC DFN
13 IN
17
GND
FE PACKAGE
16-LEAD PLASTIC TSSOP
TJMAX = 125°C, θJA = 40°C/ W, θJC = 16°C/ W
EXPOSED PAD (PIN 13) IS GND
MUST BE SOLDERED TO PCB
TJMAX = 125°C, θJA = 40°C/ W, θJC = 16°C/ W
EXPOSED PAD (PIN 17) IS GND
MUST BE SOLDERED TO PCB
ORDER PART NUMBER
DE PART MARKING
ORDER PART NUMBER
FE PART MARKING
LT3012BEDE
3012B
LT3012BEFE
3012BEFE
Order Options Tape and Reel: Add #TR
Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF
Lead Free Part Marking: http://www.linear.com/leadfree/
Consult LTC Marketing for parts specified with wider operating temperature ranges.
ELECTRICAL CHARACTERISTICS
The ● denotes specifications which apply over the full operating temperature range, otherwise specifications are at TJ = 25°C.
PARAMETER
CONDITIONS
MIN
TYP
Minimum Input Voltage
ADJ Pin Voltage (Notes 2, 3)
ILOAD = 250mA
●
VIN = 4V, ILOAD = 1mA
4.5V < VIN < 80V, 1mA < ILOAD < 250mA
1.225
●
1.2
Line Regulation
∆VIN = 4V to 80V, ILOAD = 1mA (Note 2)
●
0.1
5
mV
Load Regulation (Note 2)
VIN = 4.5V, ∆ILOAD = 1mA to 250mA
VIN = 4.5V, ∆ILOAD = 1mA to 250mA
7
12
25
mV
mV
●
MAX
UNITS
4
4.5
V
1.24
1.24
1.255
1.28
V
V
3012bf
2
LT3012B
ELECTRICAL CHARACTERISTICS
The ● denotes specifications which apply over the full operating temperature range, otherwise specifications are at TJ = 25°C.
PARAMETER
CONDITIONS
Dropout Voltage
VIN = VOUT(NOMINAL)
ILOAD = 10mA
ILOAD = 10mA
MIN
●
(Notes 4, 5)
ILOAD = 50mA
ILOAD = 50mA
●
ILOAD = 250mA
ILOAD = 250mA
●
●
TYP
MAX
UNITS
160
230
300
mV
mV
250
340
420
mV
mV
400
490
620
mV
mV
40
3
10
100
µA
mA
mA
GND Pin Current
VIN = 4.5V
(Notes 4, 6)
ILOAD = 0mA
ILOAD = 100mA
ILOAD = 250mA
Output Voltage Noise
COUT = 10µF, ILOAD = 250mA, BW = 10Hz to 100kHz
100
ADJ Pin Bias Current
(Note 7)
30
Ripple Rejection
VIN = 7V(Avg), VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 250mA
Current Limit
VIN = 7V, VOUT = 0V
VIN = 4.5V, ∆VOUT = –0.1V (Note 2)
Reverse Output Current (Note 8)
VOUT = 1.24V, VIN < 1.24V (Note 2)
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT3012B is tested and specified for these conditions with the
ADJ pin connected to the OUT pin.
Note 3: Operating conditions are limited by maximum junction
temperature. The regulated output voltage specification will not apply for
all possible combinations of input voltage and output current. When
operating at maximum input voltage, the output current range must be
limited. When operating at maximum output current, the input voltage
range must be limited.
Note 4: To satisfy requirements for minimum input voltage, the LT3012B
is tested and specified for these conditions with an external resistor divider
(249k bottom, 549k top) for an output voltage of 4V. The external resistor
divider will add a 5µA DC load on the output.
Note 5: Dropout voltage is the minimum input to output voltage differential
needed to maintain regulation at a specified output current. In dropout, the
output voltage will be equal to (VIN – VDROPOUT).
●
65
●
18
µVRMS
100
nA
75
dB
400
mA
mA
270
12
25
µA
Note 6: GND pin current is tested with VIN = 4.5V and a current source
load. This means the device is tested while operating close to its dropout
region. This is the worst-case GND pin current. The GND pin current will
decrease slightly at higher input voltages.
Note 7: ADJ pin bias current flows into the ADJ pin.
Note 8: Reverse output current is tested with the IN pin grounded and the
OUT pin forced to the rated output voltage. This current flows into the OUT
pin and out the GND pin.
Note 9: The LT3012BE is guaranteed to meet performance specifications
from 0°C to 125°C operating junction temperature. Specifications over
the –40°C to 125°C operating junction temperature range are assured by
design, characterization and correlation with statistical process controls.
Note 10: This IC includes overtemperature protection that is intended to
protect the device during momentary overload conditions. Junction
temperature will exceed 125°C when overtemperature protection is
active. Continuous operation above the specified maximum operating
junction temperature may impair device reliability.
3012bf
3
LT3012B
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Typical Dropout Voltage
Guaranteed Dropout Voltage
600
400
TJ = 25°C
300
200
100
0
TJ ≤ 125°C
500
500
400
DROPOUT VOLTAGE (mV)
TJ = 125°C
= TEST POINTS
TJ ≤ 25°C
300
200
100
100
150
200
OUTPUT CURRENT (mA)
0
250
50
150
100
200
OUTPUT CURRENT (mA)
Quiescent Current
50
40
30
20
0
50
75
25
TEMPERATURE (°C)
100
125
IL = 1mA
1.250
1.245
1.240
1.235
1.230
10
0
50
75
25
TEMPERATURE (°C)
100
RL = 1.24k
IL = 1mA*
3 4 5 6 7
INPUT VOLTAGE (V)
9
10
3012B G07
1
2
3 4 5 6 7
INPUT VOLTAGE (V)
8
5
RL = 12.4Ω
IL = 100mA*
3
0
10
VIN = 4.5V
9 TJ = 25°C
= 1.24V
V
8 OUT
6
4
9
GND Pin Current vs ILOAD
2
8
0
10
RL = 4.96Ω
IL = 250mA*
7
7
6
5
4
3
2
1
2
20
3012B G06
TJ = 25°C, *FOR VOUT = 1.24V
8
0.4
1
30
0
125
9
GND PIN CURRENT (mA)
0.6
0
40
GND Pin Current
RL = 124Ω
IL = 10mA*
0.2
50
3012B G05
TJ = 25°C
*FOR VOUT = 1.24V
0.8
60
10
1.220
– 50 – 25
GND Pin Current
125
100
TJ = 25°C
RL = ∞
VOUT = 1.24V
70
3012B G04
RL = 49.6Ω
IL = 25mA*
50
25
0
75
TEMPERATURE (°C)
Quiescent Current
1.225
10
IL = 1mA
80
QUIESCENT CURRENT (µA)
ADJ PIN VOLTAGE (V)
QUIESCENT CURRENT (µA)
60
1.0
IL = 10mA
3012B G03
1.255
70
1.2
200
ADJ Pin Voltage
1.260
VIN = 6V
90 RL = ∞
I =0
80 L
0
– 50 – 25
IL = 50mA
301B2 G02
100
GND PIN CURRENT (mA)
250
IL = 100mA
300
0
–50 –25
0
50
0
IL = 250mA
400
100
3012B G01
0
Dropout Voltage
600
GND PIN CURRENT (mA)
DROPOUT VOLTAGE (mV)
500
GUARANTEED DROPOUT VOLTAGE (mV)
600
1
RL = 24.8Ω, IL = 50mA*
0
1
2
3 4 5 6 7
INPUT VOLTAGE (V)
8
9
10
3012B G08
0
0
50
100
150
200
LOAD CURRENT (mA)
250
3012B G09
3012bf
4
LT3012B
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Current Limit
45
900
40
800
35
30
25
20
15
300
0
125
TJ = 125°C
400
100
100
TJ = 25°C
500
5
50
75
25
TEMPERATURE (°C)
600
600
200
0
VOUT = 0V
700
10
0
– 50 – 25
Current Limit
700
CURRENT LIMIT (mA)
1000
CURRENT LIMIT (mA)
ADJ PIN BIAS CURRENT (nA)
ADJ Pin Bias Current
50
10
0
20
30 40 50 60
INPUT VOLTAGE (V)
120
ADJ
PIN CLAMP
(SEE APPLICATIONS
INFORMATION)
40
20
2
3 4 5 6 7 8
OUTPUT VOLTAGE (V)
9
30
25
20
15
10
5
75
50
25
TEMPERATURE (°C)
100
0
80
76
72
68
VIN = 4.5V + 0.5VP-P RIPPLE AT f = 120Hz
IL = 250mA
VOUT = 1.24V
60
–50 –25
125
50
25
0
75
TEMPERATURE (°C)
100
125
3012B G18
3012B G17
Minimum Input Voltage
4.0
VIN = 4.5V + 50mVRMS RIPPLE
90 ILOAD = 250mA
70
60
COUT = 10µF
40
30
20
0
100k
3.0
2.5
2.0
1.5
1.0
0.5
COUT = 3.3µF
1k
10k
FREQUENCY (Hz)
ILOAD = 250mA
3.5
80
100
84
64
0
– 50 – 25
10
125
100
88
Input Ripple Rejection
10
50
25
0
75
TEMPERATURE (°C)
3012B G15
VIN = 0V
VOUT = VADJ = 1.24V
100
10
0
–50 –25
80
Input Ripple Rejection
3012B G16
50
VIN = 7V
VOUT = 0V
92
MINIMUM INPUT VOLTAGE (V)
1
70
RIPPLE REJECTION (dB)
REVERSE OUTPUT CURRENT (µA)
140
RIPPLE REJECTION (dB)
REVERSE OUTPUT CURRENT (µA)
35
TJ = 25°C
180 VIN = 0V
VOUT = VADJ
160
0
200
Reverse Output Current
Reverse Output Current
0
300
3012B G14
200
60
400
100
3012B G13
100 CURRENT FLOWS
80 INTO OUTPUT PIN
500
1M
3012B G19
0
– 50 – 25
0
50
75
25
TEMPERATURE (°C)
100
125
3012B G20
3012bf
5
LT3012B
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Load Regulation
0
COUT = 3.3µF
ILOAD = 250mA
–2
LOAD REGULATION (mV)
OUTPUT NOISE SPECTRAL DENSITY (µV/√Hz)
Output Noise Spectral Density
10
1
0.1
∆IL = 1mA TO 250mA
–4
–6
–8
–10
–12
–14
–16
–18
0.01
10
100
1k
10k
FREQUENCY (Hz)
–20
– 50 – 25
100k
75
50
25
TEMPERATURE (°C)
0
100
3012B G22
125
3012B G21
10Hz to 100kHz Output Noise
Transient Response
VOUT
100µV/DIV
COUT = 10µF
IL = 250mA
VOUT = 1.24V
1ms/DIV
3012B G23
LOAD CURRENT (mA)
OUTPUT VOLTAGE
DEVIATION (V)
0.15
0.10
0.05
0
–0.05
VIN = 6V
VOUT = 5V
CIN = 3.3µF CERAMIC
COUT = 3.3µF CERAMIC
∆ILOAD = 100mA TO 200mA
–0.10
–0.15
300
200
100
0
0
100
300
200
TIME (µs)
400
500
3012B G24
3012bf
6
LT3012B
U
U
U
PI FU CTIO S
(DFN Package)/(TSSOP Package)
OUT (Pins 2, 3)/(Pins 3, 4): Output. The output supplies
power to the load. A minimum output capacitor of 3.3µF is
required to prevent oscillations. Larger output capacitors
will be required for applications with large transient loads
to limit peak voltage transients. See the Applications
Information section for more information on output capacitance and reverse output characteristics.
ADJ (Pin 4)/(Pin 5): Adjust. This is the input to the error
amplifier. This pin is internally clamped to ±7V. It has a
bias current of 30nA which flows into the pin (see curve of
ADJ Pin Bias Current vs Temperature in the Typical Performance Characteristics). The ADJ pin voltage is 1.24V
referenced to ground, and the output voltage range is
1.24V to 60V.
GND (Pins 5, 13)/(Pins 1, 6, 8, 9, 16, 17): Ground. The
exposed backside of the package is an electrical connection for GND. As such, to ensure optimum device operation and thermal performance, the exposed pad must be
connected directly to pin 5/pin 6 on the PC board.
IN (Pins 10, 11)/(Pins 13,14): Input. Power is supplied to
the device through the IN pin. A bypass capacitor is
required on this pin if the device is more than six inches
away from the main input filter capacitor. In general, the
output impedance of a battery rises with frequency, so it
is advisable to include a bypass capacitor in batterypowered circuits. A bypass capacitor in the range of 1µF to
10µF is sufficient. The LT3012B is designed to withstand
reverse voltages on the IN pin with respect to ground and
the OUT pin. In the case of a reversed input, which can
happen if a battery is plugged in backwards, the LT3012B
will act as if there is a diode in series with its input. There
will be no reverse current flow into the LT3012B and no
reverse voltage will appear at the load. The device will
protect both itself and the load.
NC (Pins 1, 6-9, 12)/(Pins 2, 7, 10-12, 15): No Connect.
No Connect pins may be floated, tied to IN or tied to GND.
3012bf
7
LT3012B
U
W
U U
APPLICATIO S I FOR ATIO
The LT3012B is a 250mA high voltage low dropout regulator with micropower quiescent current. The device is
capable of supplying 250mA at a dropout voltage of
400mV. Operating quiescent current is only 40µA. In
addition to the low quiescent current, the LT3012B incorporates several protection features which make it ideal for
use in battery-powered systems. The device is protected
against both reverse input and reverse output voltages. In
battery backup applications where the output can be held
up by a backup battery when the input is pulled to ground,
the LT3012B acts like it has a diode in series with its output
and prevents reverse current flow.
Adjustable Operation
The LT3012B has an output voltage range of 1.24V to
60V. The output voltage is set by the ratio of two external
resistors as shown in Figure 1. The device servos the
output to maintain the voltage at the adjust pin at 1.24V
referenced to ground. The current in R1 is then equal to
1.24V/R1 and the current in R2 is the current in R1 plus
the ADJ pin bias current. The ADJ pin bias current, 30nA
at 25°C, flows through R2 into the ADJ pin. The output
voltage can be calculated using the formula in Figure 1.
The value of R1 should be less than 250k to minimize
errors in the output voltage caused by the ADJ pin bias
current.
The adjustable device is tested and specified with the ADJ
pin tied to the OUT pin and a 5µA DC load (unless otherwise
specified) for an output voltage of 1.24V. Specifications
for output voltages greater than 1.24V will be proportional
IN
VIN
to the ratio of the desired output voltage to 1.24V; (VOUT/
1.24V). For example, load regulation for an output current
change of 1mA to 250mA is –7mV typical at VOUT = 1.24V.
At VOUT = 12V, load regulation is:
(12V/1.24V) • (–7mV) = –68mV
Output Capacitance and Transient Response
The LT3012B is designed to be stable with a wide range of
output capacitors. The ESR of the output capacitor affects
stability, most notably with small capacitors. A minimum
output capacitor of 3.3µF with an ESR of 3Ω or less is
recommended to prevent oscillations. The LT3012B is a
micropower device and output transient response will be
a function of output capacitance. Larger values of output
capacitance decrease the peak deviations and provide
improved transient response for larger load current
changes. Bypass capacitors, used to decouple individual
components powered by the LT3012B, will increase the
effective output capacitor value.
Extra consideration must be given to the use of ceramic
capacitors. Ceramic capacitors are manufactured with a
variety of dielectrics, each with different behavior across
temperature and applied voltage. The most common dielectrics used are specified with EIA temperature characteristic codes of Z5U, Y5V, X5R and X7R. The Z5U and Y5V
dielectrics are good for providing high capacitances in a
small package, but they tend to have strong voltage and
temperature coefficients as shown in Figures 2 and 3.
When used with a 5V regulator, a 16V 10µF Y5V capacitor
OUT
R2
LT3012B
C1
+
VOUT
ADJ
GND
R1
3012B F01
( )
VOUT = 1.24V 1 + R2 + (IADJ)(R2)
R1
VADJ = 1.24V
IADJ = 30nA AT 25°C
OUTPUT RANGE = 1.24V TO 60V
Figure 1. Adjustable Operation
3012bf
8
LT3012B
U
W
U U
APPLICATIO S I FOR ATIO
can exhibit an effective value as low as 1µF to 2µF for the
DC bias voltage applied and over the operating temperature range. The X5R and X7R dielectrics result in more
stable characteristics and are more suitable for use as the
output capacitor. The X7R type has better stability across
temperature, while the X5R is less expensive and is
available in higher values. Care still must be exercised
when using X5R and X7R capacitors; the X5R and X7R
codes only specify operating temperature range and maximum capacitance change over temperature. Capacitance
change due to DC bias with X5R and X7R capacitors is
better than Y5V and Z5U capacitors, but can still be
significant enough to drop capacitor values below appropriate levels. Capacitor DC bias characteristics tend to
improve as component case size increases, but expected
capacitance at operating voltage should be verified.
Voltage and temperature coefficients are not the only
sources of problems. Some ceramic capacitors have a
piezoelectric response. A piezoelectric device generates
voltage across its terminals due to mechanical stress,
similar to the way a piezoelectric accelerometer or microphone works. For a ceramic capacitor the stress can be
induced by vibrations in the system or thermal transients.
Current Limit and Safe Operating Area Protection
Like many IC power regulators, the LT3012B has safe
operating area protection. The safe operating area protection decreases the current limit as the input voltage
increases and keeps the power transistor in a safe operat20
ing region. The protection is designed to provide some
output current at all values of input voltage up to the device
breakdown (see curve of Current Limit vs Input Voltage in
the Typical Performance Characteristics).
The LT3012B is limited for operating conditions by maximum junction temperature. While operating at maximum
input voltage, the output current range must be limited;
when operating at maximum output current, the input
voltage range must be limited. Device specifications will
not apply for all possible combinations of input voltage
and output current. Operating the LT3012B beyond the
maximum junction temperature rating may impair the life
of the device.
Thermal Considerations
The power handling capability of the device will be limited
by the maximum rated junction temperature (125°C). The
power dissipated by the device will be made up of two
components:
1. Output current multiplied by the input/output voltage
differential: IOUT • (VIN – VOUT) and,
2. GND pin current multiplied by the input voltage:
IGND • VIN.
The GND pin current can be found by examining the GND
Pin Current curves in the Typical Performance Characteristics. Power dissipation will be equal to the sum of the two
components listed above.
40
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10µF
20
X5R
CHANGE IN VALUE (%)
CHANGE IN VALUE (%)
0
–20
–40
–60
Y5V
–80
–100
0
X5R
–20
–40
Y5V
–60
–80
0
2
4
8
6
10 12
DC BIAS VOLTAGE (V)
14
16
3012B F02
Figure 2. Ceramic Capacitor DC Bias Characterics
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10µF
–100
50
25
75
–50 –25
0
TEMPERATURE (°C)
100
125
3012B F03
Figure 3. Ceramic Capacitor Temperature Characterics
3012bf
9
LT3012B
U
W
U U
APPLICATIO S I FOR ATIO
The LT3012B has internal thermal limiting designed to
protect the device during overload conditions. For continuous normal conditions the maximum junction temperature rating of 125°C must not be exceeded. It is
important to give careful consideration to all sources of
thermal resistance from junction to ambient. Additional
heat sources mounted nearby must also be considered.
For surface mount devices, heat sinking is accomplished
by using the heat spreading capabilities of the PC board
and its copper traces. Copper board stiffeners and plated
through-holes can also be used to spread the heat generated by power devices.
The following tables list thermal resistance for several
different board sizes and copper areas. All measurements
were taken in still air on 3/32" FR-4 board with one ounce
copper.
Table 1. DFN Measured Thermal Resistance
COPPER AREA
TOPSIDE
BACKSIDE
BOARD AREA
THERMAL RESISTANCE
(JUNCTION-TO-AMBIENT)
2500 sq mm
2500 sq mm
2500 sq mm
40°C/W
1000 sq mm
2500 sq mm
2500 sq mm
45°C/W
225 sq mm
2500 sq mm
2500 sq mm
50°C/W
100 sq mm
2500 sq mm
2500 sq mm
62°C/W
Table 2. TSSOP Measured Thermal Resistance
COPPER AREA
Continuous operation at large input/output voltage differentials and maximum load current is not practical due to
thermal limitations. Transient operation at high input/
output differentials is possible. The approximate thermal
time constant for a 2500sq mm 3/32" FR-4 board with
maximum topside and backside area for one ounce copper
is 3 seconds. This time constant will increase as more
thermal mass is added (i.e. vias, larger board, and other
components).
For an application with transient high power peaks, average power dissipation can be used for junction temperature calculations as long as the pulse period is significantly
less than the thermal time constant of the device and
board.
Calculating Junction Temperature
Example 1: Given an output voltage of 5V, an input voltage
range of 24V to 30V, an output current range of 0mA to
50mA, and a maximum ambient temperature of 50°C,
what will the maximum junction temperature be?
The power dissipated by the device will be equal to:
IOUT(MAX) • (VIN(MAX) – VOUT) + (IGND • VIN(MAX))
where:
IOUT(MAX) = 50mA
TOPSIDE
BACKSIDE
BOARD AREA
THERMAL RESISTANCE
(JUNCTION-TO-AMBIENT)
2500 sq mm
2500 sq mm
2500 sq mm
40°C/W
1000 sq mm
2500 sq mm
2500 sq mm
45°C/W
225 sq mm
2500 sq mm
2500 sq mm
50°C/W
100 sq mm
2500 sq mm
2500 sq mm
62°C/W
The thermal resistance junction-to-case (θJC), measured
at the exposed pad on the back of the die, is 16°C/W.
VIN(MAX) = 30V
IGND at (IOUT = 50mA, VIN = 30V) = 1mA
So:
P = 50mA • (30V – 5V) + (1mA • 30V) = 1.28W
The thermal resistance will be in the range of 40°C/W to
62°C/W depending on the copper area. So the junction
temperature rise above ambient will be approximately
equal to:
1.31W • 50°C/W = 65.5°C
3012bf
10
LT3012B
U
W
U U
APPLICATIO S I FOR ATIO
The maximum junction temperature will then be equal to
the maximum junction temperature rise above ambient
plus the maximum ambient temperature or:
TJMAX = 50°C + 65.5°C = 115.5°C
Example 2: Given an output voltage of 5V, an input voltage
of 48V that rises to 72V for 5ms(max) out of every 100ms,
and a 5mA load that steps to 50mA for 50ms out of every
250ms, what is the junction temperature rise above ambient? Using a 500ms period (well under the time constant
of the board), power dissipation is as follows:
P1(48V in, 5mA load) = 5mA • (48V – 5V)
+ (200µA • 48V) = 0.23W
P2(48V in, 50mA load) = 50mA • (48V – 5V)
+ (1mA • 48V) = 2.20W
P3(72V in, 5mA load) = 5mA • (72V – 5V)
+ (200µA • 72V) = 0.35W
P4(72V in, 50mA load) = 50mA • (72V – 5V)
+ (1mA • 72V) = 3.42W
Operation at the different power levels is as follows:
76% operation at P1, 19% for P2, 4% for P3, and
1% for P4.
PEFF = 76%(0.23W) + 19%(2.20W) + 4%(0.35W)
+ 1%(3.42W) = 0.64W
With a thermal resistance in the range of 40°C/W to
62°C/W, this translates to a junction temperature rise
above ambient of 26°C to 38°C.
Protection Features
The LT3012B incorporates several protection features
which make it ideal for use in battery-powered circuits. In
addition to the normal protection features associated with
monolithic regulators, such as current limiting and thermal limiting, the device is protected against reverse-input
voltages, and reverse voltages from output to input.
Current limit protection and thermal overload protection
are intended to protect the device against current overload
conditions at the output of the device. For normal operation, the junction temperature should not exceed 125°C.
The input of the device will withstand reverse voltages of
80V. No negative voltage will appear at the output. The
device will protect both itself and the load. This provides
protection against batteries which can be plugged in
backward.
The ADJ pin of the device can be pulled above or below
ground by as much as 7V without damaging the device. If
the input is left open circuit or grounded, the ADJ pin will
act like an open circuit when pulled below ground, and like
a large resistor (typically 100k) in series with a diode when
pulled above ground. If the input is powered by a voltage
source, pulling the ADJ pin below the reference voltage
will cause the device to current limit. This will cause the
output to go to a unregulated high voltage. Pulling the ADJ
pin above the reference voltage will turn off all output
current.
3012bf
11
LT3012B
U
W
U U
APPLICATIO S I FOR ATIO
In situations where the ADJ pin is connected to a resistor
divider that would pull the ADJ pin above its 7V clamp
voltage if the output is pulled high, the ADJ pin input
current must be limited to less than 5mA. For example, a
resistor divider is used to provide a regulated 1.5V output
from the 1.24V reference when the output is forced to 60V.
The top resistor of the resistor divider must be chosen to
limit the current into the ADJ pin to less than 5mA when the
ADJ pin is at 7V. The 53V difference between the OUT and
ADJ pins divided by the 5mA maximum current into the
ADJ pin yields a minimum top resistor value of 10.6k.
In circuits where a backup battery is required, several
different input/output conditions can occur. The output
voltage may be held up while the input is either pulled to
ground, pulled to some intermediate voltage, or is left
open circuit. Current flow back into the output will follow
the curve shown in Figure 4. The rise in reverse output
current above 7V occurs from the breakdown of the 7V
clamp on the ADJ pin. With a resistor divider on the
regulator output, this current will be reduced depending
on the size of the resistor divider.
When the IN pin of the LT3012B is forced below the OUT
pin or the OUT pin is pulled above the IN pin, input current
will typically drop to less than 2µA. This can happen if the
input of the LT3012B is connected to a discharged (low
voltage) battery and the output is held up by either a
backup battery or a second regulator circuit.
REVERSE OUTPUT CURRENT (µA)
200
TJ = 25°C
180 VIN = 0V
VOUT = VADJ
160
140
120
100 CURRENT FLOWS
80 INTO OUTPUT PIN
ADJ
PIN CLAMP
(SEE ABOVE)
60
40
20
0
0
1
2
3 4 5 6 7 8
OUTPUT VOLTAGE (V)
9
10
3012B F04
Figure 4. Reverse Output Current
3012bf
12
LT3012B
U
TYPICAL APPLICATIO S
LT3012B Automotive Application
VIN
12V
(LATER 42V)
IN
+
1µF
NO PROTECTION
DIODE NEEDED!
OUT
LT3012B
750k
3.3µF
ADJ
GND
LOAD: CLOCK,
SECURITY SYSTEM
ETC
249k
LT3012B Telecom Application
VIN
48V
(72V TRANSIENT)
IN
OUT
LT3012B
1µF
ADJ
GND
750k NO PROTECTION
DIODE NEEDED!
+
3.3µF
LOAD:
SYSTEM MONITOR
ETC
–
BACKUP
BATTERY
249k
3012B TA05
Constant Brightness for Indicator LED over Wide Input Voltage Range
RETURN
IN
1µF
OUT
LT3012B
3.3µF
ADJ
GND
–48V
ILED = 1.24V/RSET
–48V CAN VARY FROM –4V TO –80V
RSET
3012B TA06
3012bf
13
LT3012B
U
PACKAGE DESCRIPTIO
DE/UE Package
12-Lead Plastic DFN (4mm × 3mm)
(Reference LTC DWG # 05-08-1695 Rev C)
0.70 ±0.05
3.60 ±0.05
1.70 ±0.05
2.20 ±0.05 (2 SIDES)
PACKAGE OUTLINE
0.25 ± 0.05
3.30 ±0.05
(2 SIDES)
0.50
BSC
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
4.00 ±0.10
(2 SIDES)
7
R = 0.115
TYP
0.40 ± 0.10
12
R = 0.05
TYP
PIN 1
TOP MARK
(NOTE 6)
0.200 REF
3.00 ±0.10
(2 SIDES)
1.70 ± 0.05
(2 SIDES)
PIN 1 NOTCH
R = 0.20 OR
0.35 × 45°
CHAMFER
0.75 ±0.05
0.00 – 0.05
6
0.25 ± 0.05
3.30 ±0.05
(2 SIDES)
1
(UE12/DE12) DFN 0905 REV C
0.50
BSC
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING PROPOSED TO BE A VARIATION OF VERSION
(WGED) IN JEDEC PACKAGE OUTLINE M0-229
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
3012bf
14
LT3012B
U
PACKAGE DESCRIPTIO
FE Package
16-Lead Plastic TSSOP (4.4mm)
(Reference LTC DWG # 05-08-1663)
Exposed Pad Variation BB
4.90 – 5.10*
(.193 – .201)
3.58
(.141)
3.58
(.141)
16 1514 13 12 1110
6.60 ±0.10
9
2.94
(.116)
4.50 ±0.10
2.94 6.40
(.116) (.252)
BSC
SEE NOTE 4
0.45 ±0.05
1.05 ±0.10
0.65 BSC
1 2 3 4 5 6 7 8
RECOMMENDED SOLDER PAD LAYOUT
4.30 – 4.50*
(.169 – .177)
0.09 – 0.20
(.0035 – .0079)
0.50 – 0.75
(.020 – .030)
NOTE:
1. CONTROLLING DIMENSION: MILLIMETERS
MILLIMETERS
2. DIMENSIONS ARE IN
(INCHES)
3. DRAWING NOT TO SCALE
0.25
REF
1.10
(.0433)
MAX
0° – 8°
0.65
(.0256)
BSC
0.195 – 0.30
(.0077 – .0118)
TYP
0.05 – 0.15
(.002 – .006)
FE16 (BB) TSSOP 0204
4. RECOMMENDED MINIMUM PCB METAL SIZE
FOR EXPOSED PAD ATTACHMENT
*DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.150mm (.006") PER SIDE
3012bf
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
15
LT3012B
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1020
125mA, Micropower Regulator and Comparator
VIN: 4.5V to 36V, VOUT(MIN) = 2.5V, VDO = 0.4V, IQ = 40µA, ISD = 40µA,
Comparator and Reference, Class B Outputs, S16, PDIP14 Packages
LT1120/LT1120A 125mA, Micropower Regulator and Comparator
VIN: 4.5V to 36V, VOUT(MIN) = 2.5V, VDO = 0.4V, IQ = 40µA, ISD = 10µA,
Comparator and Reference, Logic Shutdown, Ref Sources and Sinks 2/4mA,
S8, N8 Packages
LT1121/
LT1121HV
150mA, Micropower, LDO
VIN: 4.2V to 30/36V, VOUT(MIN) = 3.75V, VDO = 0.42V, IQ = 30µA, ISD = 16µA,
Reverse Battery Protection, SOT-223, S8, Z Packages
LT1129
700mA, Micropower, LDO
VIN: 4.2V to 30V, VOUT(MIN) = 3.75V, VDO = 0.4V, IQ = 50µA, ISD = 16µA,
DD, S0T-223, S8,TO220-5, TSSOP20 Packages
LT1676
60V, 440mA (IOUT), 100kHz, High Efficiency
Step-Down DC/DC Converter
VIN: 7.4V to 60V, VOUT(MIN) = 1.24V, IQ = 3.2mA, ISD = 2.5µA, S8 Package
LT1761
100mA, Low Noise Micropower, LDO
VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.3V, IQ = 20µA, ISD = <1µA,
Low Noise < 20µVRMS, Stable with 1µF Ceramic Capacitors, ThinSOT Package
LT1762
150mA, Low Noise Micropower, LDO
VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.3V, IQ = 25µA, ISD = <1µA,
Low Noise < 20µVRMS, MS8 Package
LT1763
500mA, Low Noise Micropower, LDO
VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.3V, IQ = 30µA, ISD = <1µA,
Low Noise < 20µVRMS, S8 Package
LT1764/LT1764A 3A, Low Noise, Fast Transient Response, LDO
VIN: 2.7V to 20V, VOUT(MIN) = 1.21V, VDO = 0.34V, IQ = 1mA, ISD = <1µA,
Low Noise < 40µVRMS, “A” Version Stable with Ceramic Capacitors,
DD, TO220-5 Packages
LT1766
60V, 1.2A (IOUT), 200kHz, High Efficiency
Step-Down DC/DC Converter
VIN: 5.5V to 60V, VOUT(MIN) = 1.2V, IQ = 2.5mA, ISD = 25µA, TSSOP16/E Package
LT1776
40V, 550mA (IOUT), 200kHz, High Efficiency
Step-Down DC/DC Converter
VIN: 7.4V to 40V, VOUT(MIN) = 1.24V, IQ = 3.2mA, ISD = 30µA, N8, S8 Packages
LT1934/
LT1934-1
300mA/60mA, (IOUT), Constant Off-Time, High
Efficiency Step-Down DC/DC Converter
90% Efficiency, VIN: 3.2V to 34V, VOUT(MIN) = 1.25V, IQ = 14µA, ISD = <1µA,
ThinSOT Package
LT1956
60V, 1.2A (IOUT), 500kHz, High Efficiency
Step-Down DC/DC Converter
VIN: 5.5V to 60V, VOUT(MIN) = 1.2V, IQ = 2.5mA, ISD = 25µA, TSSOP16/E Package
LT1962
300mA, Low Noise Micropower, LDO
VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.27V, IQ = 30µA, ISD = <1µA,
Low Noise < 20µVRMS, MS8 Package
LT1963/LT1963A 1.5A, Low Noise, Fast Transient Response, LDO
VIN: 2.1V to 20V, VOUT(MIN) = 1.21V, VDO = 0.34V, IQ = 1mA, ISD = <1µA,
Low Noise < 40µVRMS, “A” Version Stable with Ceramic Capacitors,
DD, TO220-5, S0T-223, S8 Packages
LT1964
200mA, Low Noise Micropower, Negative LDO
VIN: –1.9V to –20V, VOUT(MIN) = –1.21V, VDO = 0.34V, IQ = 30µA, ISD = 3µA,
Low Noise < 30µVRMS, Stable with Ceramic Capacitors, ThinSOT Package
LT3010
100mA, 3V to 80V, Low Noise Micropower LDO
VIN: 3V to 8V, VOUT(MIN) = 1.275V, VDO = 0.3V, IQ = 30µA, ISD = 1µA,
Low Noise < 100µVRMS, MS8E Package
3012bf
16
Linear Technology Corporation
LT 0206 • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2006