TI LP2950-33LPR Adjustable micropower voltage regulators with shutdown Datasheet

Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
LP2950, LP2951
SLVS582I – APRIL 2006 – REVISED NOVEMBER 2014
LP295x Adjustable Micropower Voltage Regulators with Shutdown
1 Features
2 Applications
•
•
•
•
•
•
•
•
•
1
•
•
•
•
•
Wide Input Range: Up to 30 V
Rated Output Current of 100 mA
Low Dropout: 380 mV (Typ) at 100 mA
Low Quiescent Current: 75 μA (Typ)
Tight Line Regulation: 0.03% (Typ)
Tight Load Regulation: 0.04% (Typ)
High VO Accuracy
– 1.4% at 25°C
– 2% Over Temperature
Can Be Used as a Regulator or Reference
Stable With Low ESR (>12 mΩ) Capacitors
Current- and Thermal-Limiting Features
LP2950 Only (3-Pin Package)
– Fixed-Output Voltages of 5 V, 3.3 V, and 3 V
LP2951 Only (8-Pin Package)
– Fixed- or Adjustable-Output Voltages:
5 V/ADJ, 3.3 V/ADJ, and 3 V/ADJ
– Low-Voltage Error Signal on Falling Output
– Shutdown Capability
– Remote Sense Capability for Optimal Output
Regulation and Accuracy
Applications with High-Voltage Input
Power Supplies
3 Description
The LP2950 and LP2951 devices are bipolar, lowdropout voltage regulators that can accommodate a
wide input supply-voltage range of up to 30 V. The
easy-to-use, 3-pin LP2950 is available in fixed-output
voltages of 5 V, 3.3 V, and 3 V. However, the 8-pin
LP2951 is able to output either a fixed or adjustable
output from the same device. By tying the OUTPUT
and SENSE pins together, and the FEEDBACK and
VTAP pins together, the LP2951 outputs a fixed 5 V,
3.3 V, or 3 V (depending on the version).
Alternatively, by leaving the SENSE and VTAP pins
open and connecting FEEDBACK to an external
resistor divider, the output can be set to any value
between 1.235 V to 30 V.
Device Information(1)
PART NUMBER
LP2950
LP2951
PACKAGE
BODY SIZE (NOM)
TO-92 (3)
4.83 mm x 4.83 mm
SOIC (8)
4.90 mm x 3.90 mm
SON (8)
3.00 mm x 3.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Dropout Voltage vs Temperature
500
(V IN – V OUT ) – Dropout Voltage – mV
450
400
350
RIL = 100 m A
300
250
200
150
100
RIL = 100 µA
50
0
-40 -25 -10
5
20 35
50 65
80 95 110 125
TA – Temperature – °C
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LP2950, LP2951
SLVS582I – APRIL 2006 – REVISED NOVEMBER 2014
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
4
4
4
4
5
7
Absolute Maximum Ratings ......................................
Handling Ratings ......................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description ............................................ 12
7.1 Overview ................................................................. 12
7.2 LP2950 Functional Block Diagram.......................... 12
7.3 LP2951 Functional Block Diagram.......................... 13
7.4 Feature Description................................................. 14
7.5 Device Functional Modes........................................ 15
8
Application and Implementation ........................ 16
8.1 Application Information............................................ 16
8.2 Typical Application ................................................. 16
9 Power Supply Recommendations...................... 19
10 Layout................................................................... 19
10.1 Layout Guidelines ................................................. 19
10.2 Layout Example .................................................... 19
11 Device and Documentation Support ................. 19
11.1 Trademarks ........................................................... 19
11.2 Electrostatic Discharge Caution ............................ 19
11.3 Glossary ................................................................ 19
12 Mechanical, Packaging, and Orderable
Information ........................................................... 19
4 Revision History
Changes from Revision H (March 2012) to Revision I
Page
•
Added Applications, Device Information table, Handling Ratings table, Feature Description section, Device
Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout
section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section. ..... 1
•
Removed Ordering Information table. .................................................................................................................................... 1
2
Submit Documentation Feedback
Copyright © 2006–2014, Texas Instruments Incorporated
Product Folder Links: LP2950 LP2951
LP2950, LP2951
www.ti.com
SLVS582I – APRIL 2006 – REVISED NOVEMBER 2014
5 Pin Configuration and Functions
LP2951
D OR P PACKAGE
(TOP VIEW)
LP2950
LP PACKAGE
(BOTTOM VIEW)
OUTPUT
GND
INPUT
OUTPUT
SENSE
SHUTDOWN
GND
1
8
2
7
3
6
4
5
INPUT
FEEDBACK
VTAP
ERROR
LP2951
DRG PACKAGE
(TOP VIEW)
OUTPUT
SENSE
SHUTDOWN
GND
1
8
2
7
3
4
Thermal
Pad
6
5
INPUT
FEEDBACK
VTAP
ERROR
Pin Functions
PIN
NAME
TYPE
DESCRIPTION
LP2950
LP2951
ERROR
—
5
O
Active-low open-collector error output. Goes low when VOUT drops by 6% of its
nominal value.
FEEDBACK
—
7
I
Determines the output voltage. Connect to VTAP (with OUTPUT tied to SENSE)
to output the fixed voltage corresponding to the part version, or connect to a
resistor divider to adjust the output voltage.
GND
2
4
—
INPUT
3
8
I
Supply input
OUTPUT
1
1
O
Voltage output.
SENSE
—
2
I
Senses the output voltage. Connect to OUTPUT (with FEEDBACK tied to VTAP)
to output the voltage corresponding to the part version.
SHUTDOWN
—
3
I
Active-high input. Shuts down the device.
VTAP
—
6
O
Tie to FEEDBACK to output the fixed voltage corresponding to the part version.
Ground
Submit Documentation Feedback
Copyright © 2006–2014, Texas Instruments Incorporated
Product Folder Links: LP2950 LP2951
3
LP2950, LP2951
SLVS582I – APRIL 2006 – REVISED NOVEMBER 2014
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)
(1)
MIN
MAX
UNIT
VIN
Continuous input voltage range
–0.3
30
V
VSHDN
SHUTDOWN input voltage range
–1.5
30
V
VERROR
ERROR comparator output voltage range (2)
–1.5
30
V
VFDBK
FEEDBACK input voltage range (2)
–1.5
30
V
(1)
(2)
(3)
(3)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
May exceed input supply voltage
If load is returned to a negative power supply, the output must be diode clamped to GND.
6.2 Handling Ratings
Tstg
V(ESD)
(1)
(2)
MIN
MAX
UNIT
–65
150
°C
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all
pins (1)
0
2500
Charged device model (CDM), per JEDEC specification
JESD22-C101, all pins (2)
0
1000
Storage temperature range
Electrostatic discharge
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
MIN
VIN
Supply input voltage
TJ
Operating virtual junction temperature
(1)
MAX
UNIT
(1)
30
V
–40
125
°C
See
Minimum VIN is the greater of:
(a) 2 V (25°C), 2.3 V (over temperature), or
(b) VOUT(MAX) + Dropout (Max) at rated IL
6.4 Thermal Information
LP2950
THERMAL METRIC (1)
LP
LP2951
D
P
3 PINS
RθJA
(1)
4
Junction-to-ambient thermal resistance
140
DRG
UNIT
52.44
°C/W
8 PINS
97
84.6
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report (SPRA953).
Submit Documentation Feedback
Copyright © 2006–2014, Texas Instruments Incorporated
Product Folder Links: LP2950 LP2951
LP2950, LP2951
www.ti.com
SLVS582I – APRIL 2006 – REVISED NOVEMBER 2014
6.5 Electrical Characteristics
VIN = VOUT (nominal) + 1 V, IL = 100 μA, CL = 1 μF (5-V versions) or CL = 2.2 μF (3-V and 3.3-V versions),
8-pin version: FEEDBACK tied to VTAP, OUTPUT tied to SENSE, VSHUTDOWN ≤ 0.7 V
PARAMETER
TEST CONDITIONS
TJ
MIN
TYP
MAX
UNIT
3-V VERSION (LP295x-30)
VOUT
Output voltage
IL = 100 μA
25°C
2.970
3
3.030
–40°C to 125°C
2.940
3
3.060
25°C
3.267
3.3
3.333
–40°C to 125°C
3.234
3.3
3.366
25°C
4.950
5
5.050
–40°C to 125°C
4.900
5
5.100
V
3.3-V VERSION (LP295x-33)
VOUT
Output voltage
IL = 100 μA
V
5-V VERSION (LP295x-50)
VOUT
Output voltage
IL = 100 μA
V
ALL VOLTAGE OPTIONS
Output voltage temperature
coefficient (1)
IL = 100 μA
Line regulation (2)
VIN = [VOUT(NOM) + 1 V] to 30 V
Load regulation (2)
IL = 100 μA to 100 mA
IL = 100 μA
VIN – VOUT Dropout voltage (3)
IL = 100 mA
IL = 100 μA
IGND
GND current
IL = 100 mA
Dropout ground current
VIN = VOUT(NOM) – 0.5 V,
IL = 100 μA
Current limit
VOUT = 0 V
Thermal regulation (4)
–40°C to 125°C
25°C
(1)
(2)
(3)
(4)
0.03
–40°C to 125°C
25°C
0.04%
25°C
50
–40°C to 125°C
–40°C to 125°C
8
–40°C to 125°C
25°C
mV
12
170
160
200
220
0.05
0.2
μA
mA
μA
mA
%/W
430
CL = 200 μF
LP2951-50: CL = 3.3 μF,
CBypass = 0.01 μF between
pins 1 and 7
120
200
–40°C to 125°C
IL = 100 μA
450
14
110
25°C
—
80
140
–40°C to 125°C
25°C
%/V
600
75
25°C
0.2%
150
380
25°C
0.2
0.3%
–40°C to 125°C
25°C
100 ppm/°C
0.4
–40°C to 125°C
CL = 1 μF (5 V only)
Output noise (RMS),
10 Hz to 100 kHz
20
160
μV
25°C
100
Output or reference voltage temperature coefficient is defined as the worst-case voltage change divided by the total temperature range.
Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to
heating effects are covered under the specification for thermal regulation.
Dropout voltage is defined as the input-to-output differential at which the output voltage drops 100 mV, below the value measured at 1-V
differential. The minimum input supply voltage of 2 V (2.3 V over temperature) must be observed.
Thermal regulation is defined as the change in output voltage at a time (T) after a change in power dissipation is applied, excluding load
or line regulation effects. Specifications are for a 50-mA load pulse at VIN = 30 V, VOUT = 5 V (1.25-W pulse) for t = 10 ms.
Submit Documentation Feedback
Copyright © 2006–2014, Texas Instruments Incorporated
Product Folder Links: LP2950 LP2951
5
LP2950, LP2951
SLVS582I – APRIL 2006 – REVISED NOVEMBER 2014
www.ti.com
Electrical Characteristics (continued)
VIN = VOUT (nominal) + 1 V, IL = 100 μA, CL = 1 μF (5-V versions) or CL = 2.2 μF (3-V and 3.3-V versions),
8-pin version: FEEDBACK tied to VTAP, OUTPUT tied to SENSE, VSHUTDOWN ≤ 0.7 V
PARAMETER
TEST CONDITIONS
TJ
MIN
TYP
MAX
25°C
1.218
1.235
1.252
–40°C to 125°C
1.212
UNIT
(LP2951-xx) 8-PIN VERSION ONLY ADJ
Reference voltage
VOUT = VREF to (VIN – 1 V),
VIN = 2.3 V to 30 V,
IL = 100 μA to 100 mA
V
–40°C to 125°C
Reference voltage
temperature coefficient (1)
FEEDBACK bias current
1.257
1.200
1.272
25°C
20
25°C
20
–40°C to 125°C
FEEDBACK bias current
temperature coefficient
ppm/°C
40
60
25°C
0.1
25°C
0.01
nA
nA/°C
ERROR COMPARATOR
Output leakage current
VOUT = 30 V
Output low voltage
VIN = VOUT(NOM) – 0.5 V,
IOL = 400 μA
–40°C to 125°C
2
25°C
150
–40°C to 125°C
250
400
Upper threshold voltage
(ERROR output high) (5)
25°C
40
–40°C to 125°C
25
Lower threshold voltage
(ERROR output low) (5)
–40°C to 125°C
25°C
Hysteresis (5)
1
60
75
mV
mV
95
140
25°C
μA
15
mV
mV
SHUTDOWN INPUT
Input logic voltage
Low (regulator ON)
High (regulator OFF)
SHUTDOWN = 2.4 V
SHUTDOWN input current
SHUTDOWN = 30 V
Regulator output current
in shutdown
(5)
6
VSHUTDOWN ≥ 2 V,
VIN ≤ 30 V, VOUT = 0,
FEEDBACK tied to VTAP
–40°C to 125°C
25°C
0.7
2
30
–40°C to 125°C
25°C
–40°C to 125°C
25°C
–40°C to 125°C
50
100
450
V
600
μA
750
3
10
20
μA
Comparator thresholds are expressed in terms of a voltage differential equal to the nominal reference voltage (measured at
VIN – VOUT = 1 V) minus FEEDBACK terminal voltage. To express these thresholds in terms of output voltage change, multiply by the
error amplifier gain = VOUT/VREF = (R1 + R2)/R2. For example, at a programmed output voltage of 5 V, the ERROR output is specified to
go low when the output drops by 95 mV × 5 V/1.235 V = 384 mV. Thresholds remain constant as a percentage of VOUT (as VOUT is
varied), with the low-output warning occurring at 6% below nominal (typ) and 7.7% (max).
Submit Documentation Feedback
Copyright © 2006–2014, Texas Instruments Incorporated
Product Folder Links: LP2950 LP2951
LP2950, LP2951
www.ti.com
SLVS582I – APRIL 2006 – REVISED NOVEMBER 2014
6.6 Typical Characteristics
100
10
RL = ∞
90
Quiescent Current – mA
80
Input Current – µA
1
0.1
70
60
50
40
30
20
10
0.01
0.0001
0.001
0.01
0
0.1
0
1
2
3
IL – Load Current – A
Figure 1. Quiescent Current vs Load Current
200
4
5
6
7
8
9
10
VIN – Input Voltage – V
Figure 2. Input Current vs Input Voltage (RL = OPEN)
120
RL = 50 kΩ
RL = 50 Ω
110
180
100
160
Input Current – mA
Input Current – µA
90
140
120
100
80
60
80
70
60
50
40
30
40
20
20
10
0
0
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
VIN – Input Voltage – V
VIN – Input Voltage – V
Figure 3. Input Current vs Input Voltage (RL = 50 kΩ)
Figure 4. Input Current vs Input Voltage (RL = 50 Ω)
5.100
120
110
IL = 0
5.075
5.050
5.025
Quiescent Current – µA
VOUT – Output Voltage – V
100
IL = 100 µA
5.000
IL = 100 m A
4.975
4.950
90
80
70
60
50
40
30
20
4.925
10
4.900
-40 -25 -10 5
0
20 35 50 65 80 95 110 125
0
1
2
3
4
5
6
7
8
TA – Temperature – °C
VIN – Input Voltage – V
Figure 5. Output Voltage vs Temperature
Figure 6. Quiescent Current vs Input Voltage (IL = 0)
Submit Documentation Feedback
Copyright © 2006–2014, Texas Instruments Incorporated
Product Folder Links: LP2950 LP2951
7
LP2950, LP2951
SLVS582I – APRIL 2006 – REVISED NOVEMBER 2014
www.ti.com
Typical Characteristics (continued)
8
IL = 100 mA
120
7
IL = 1 mA
110
Quiescent Current – mA
Quiescent Current – µA
100
90
80
70
60
50
40
30
6
5
4
3
2
20
1
10
0
0
1
2
3
4
5
6
7
8
0
0
VIN – Input Voltage – V
1
2
3
4
5
6
7
8
VIN – Input Voltage – V
Figure 7. Quiescent Current vs Input Voltage (IL = 1 mA)
Figure 8. Quiescent Current vs Input Voltage (IL = 100 mA)
100
10
9.5
IL = 100 m A
V IN = 6 V
95
90
Quiescent Current – µA
Quiescent Current – mA
9
8.5
8
7.5
7
6.5
85
80
75
70
65
6
60
5.5
55
5
-40 -25 -10
IL = 100 µA
V IN = 6 V
5
20
35
50
65
80
50
-40 -25 -10
95 110 125
Figure 9. Quiescent Current vs Temperature (IL = 100 mA)
65
80
95 110 125
450
(V IN – V OUT ) – Dropout Voltage – mV
Short-Circuit Current – mA
35 50
500
225
200
175
150
125
100
75
8
20
Figure 10. Quiescent Current vs Temperature (IL = 100 µA)
250
50
-40 -25 -10
5
TA – Temperature – °C
TA – Temperature – °C
5
20
35 50
65
80
95 110 125
400
350
RIL = 100 m A
300
250
200
150
100
RIL = 100 µA
50
0
-40 -25 -10
5
20 35
50 65
80 95 110 125
TA – Temperature – °C
TA – Temperature – °C
Figure 11. Short-circuit Current vs Temperature
Figure 12. Dropout Voltage vs Temperature
Submit Documentation Feedback
Copyright © 2006–2014, Texas Instruments Incorporated
Product Folder Links: LP2950 LP2951
LP2950, LP2951
www.ti.com
SLVS582I – APRIL 2006 – REVISED NOVEMBER 2014
400
2
350
1.95
Minimum Operating Voltage – V
(V IN – V OUT ) – Dropout Voltage – mV
Typical Characteristics (continued)
300
250
200
150
100
50
1.9
1.85
1.8
1.75
1.7
1.65
0
0.0001
0.001
0.01
1.6
-40 -25 -10
0.1
IO – Output Current – A
20
35 50
65 80
95 110 125
TA – Temperature – °C
Figure 13. Dropout Voltage vs Dropout Current
Figure 14. LP2951 Minimum Operating Voltage vs
Temperature
30
8
25
7
50-kW resistor to
external 5-V supply
20
6
ERROR Output – V
FEEDBACK Bias Current – nA
5
15
10
5
0
-5
5
4
3
50-kW resistor
to VOUT
2
-10
1
-15
-20
-55
0
-30
-5
20
45
70
95
0
120 145
1
2
3
4
5
6
7
8
V IN – Input Voltage – V
TA – Temperature – °C
Figure 15. LP2951 FEEDBACK Bias Current vs Temperature
Figure 16. LP2951 ERROR Comparator Output vs
Input Voltage
2
ISINK – Sink Current – mA
1.75
TA = 125
Input Voltage
2 V/div
1.5
1.25
TA = 25
1
0.75
TA = –40
Output Voltage
80 mV/div
0.5
0.25
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
VOL – Output Low Voltage – V
Figure 18. Line Transient Response vs Time
Figure 17. LP2951 ERROR Comparator Sink Current vs
Output Low Voltage
Submit Documentation Feedback
Copyright © 2006–2014, Texas Instruments Incorporated
Product Folder Links: LP2950 LP2951
9
LP2950, LP2951
SLVS582I – APRIL 2006 – REVISED NOVEMBER 2014
www.ti.com
Typical Characteristics (continued)
Output Voltage
100 mV/div
Output Load
100 mA/div
Figure 19. Load Transient Response vs
Time (VOUT = 5 V, CL = 10 µF)
Figure 20. Enable Transient Response vs
Time (IL = 1 mA, CL = 1 µF)
100
Ω
Output Impedance – Ohm
IL = 100 µA
10
1
IL = 1 m A
0.1
IL = 100 m A
0.01
10
1.E+01
100
1.E+02
1k
1.E+03
10k
1.E+04
100k
1.E+05
1M
1.E+06
f – Frequency – Hz
Figure 21. Enable Transient Response vs
Time (IL = 1 mA, CL = 10 µF)
Figure 22. Output Impedance vs Frequency
100
90
VIN = 6 V
CL = 1 µF
80
Power-Supply Ripple Rejection – dB
Power-Supply Ripple Rejection – dB
90
IL = 0
70
60
50
IL = 100 µA
40
30
V IN = 6 V
CL = 1 µF
20
10
1.E+01
100
1.E+02
80
70
60
50
30
20
IL = 10 mA
1k
1.E+03
10k
1.E+04
100k
1.E+05
1M
1.E+06
10
1.E+01
10
1.E+02
100
1.E+03
1k
1.E+04
10k
1.E+05
100k
1.E+06
1M
f – Frequency – Hz
f – Frequency – Hz
Figure 23. Ripple Rejection vs Frequency
10
IL = 1 mA
40
Figure 24. Output Impedance vs Frequency
Submit Documentation Feedback
Copyright © 2006–2014, Texas Instruments Incorporated
Product Folder Links: LP2950 LP2951
LP2950, LP2951
www.ti.com
SLVS582I – APRIL 2006 – REVISED NOVEMBER 2014
Typical Characteristics (continued)
6
100
VIN = 6 V
80
CL = 1 µF
5
IL = 50 mA
Output Noise – µV
Power-Supply Ripple Rejection – dB
90
70
60
50
40
4
CL = 200 µF
3
CL = 1 µF
2
IL = 100 mA
30
1
20
10
10
1.E+01
CL = 3.3 µF
100
1.E+02
1k
1.E+03
10k
1.E+04
100k
1.E+05
0
1.E+01
10
1M
1.E+06
1.E+02
100
1.E+03
1k
1.E+04
10k
1.E+05
100k
f – Frequency – Hz
f – Frequency – Hz
Figure 26. LP2951 Output Noise vs Frequency
Figure 25. Output Impedance vs Frequency
1.7
1.6
Input Logic Voltage (OFF to ON) – V
RP2P4 – Pin 2 to Pin 4 Resistance – k W
400
350
300
250
200
150
100
1.5
1.4
1.3
1.2
1.1
1
0.9
50
0
-40 -25 -10
0.8
-40 -25 -10
5
20
35 50
65 80 95 110 125
TA – Temperature – °C
5
20
35
50
65
80
95 110 125
TA – Temperature – °C
Figure 28. Shutdown Threshold Voltage (Off to On) vs
Temperature
1.7
6
1.6
5
1.5
Output Voltage Change – mV
Input Logic Voltage (ON to OFF) – V
Figure 27. LP2951 Divider Resistance vs Temperature
1.4
1.3
1.2
1.1
1
3
2
1
0
-1
0.9
0.8
-40 -25 -10
4
-2
5
20
35
50
65
80
95 110 125
0
5
10
15
20
25
30
VIN – Input Voltage – V
TA – Temperature – °C
Figure 29. Shutdown Threshold Voltage (On to Off) vs
Temperature
Figure 30. Line Regulation vs Input Voltage
Submit Documentation Feedback
Copyright © 2006–2014, Texas Instruments Incorporated
Product Folder Links: LP2950 LP2951
11
LP2950, LP2951
SLVS582I – APRIL 2006 – REVISED NOVEMBER 2014
www.ti.com
7 Detailed Description
7.1 Overview
The LP2950 and LP2951 devices are bipolar, low-dropout voltage regulators that can accommodate a wide input
supply-voltage range of up to 30 V. The easy-to-use, 3-pin LP2950 is available in fixed-output voltages of 5 V,
3.3 V, and 3 V. However, the 8-pin LP2951 device is able to output either a fixed or adjustable output from the
same device. By tying the OUTPUT and SENSE pins together, and the FEEDBACK and VTAP pins together, the
LP2951 device outputs a fixed 5 V, 3.3 V, or 3 V (depending on the version). Alternatively, by leaving the SENSE
and VTAP pins open and connecting FEEDBACK to an external resistor divider, the output can be set to any
value between 1.235 V to 30 V.
The 8-pin LP2951 device also offers additional functionality that makes it particularly suitable for battery-powered
applications. For example, a logic-compatible shutdown feature allows the regulator to be put in standby mode
for power savings. In addition, there is a built-in supervisor reset function in which the ERROR output goes low
when VOUT drops by 6% of its nominal value for whatever reasons – due to a drop in VIN, current limiting, or
thermal shutdown.
The LP2950 and LP2951 devices are designed to minimize all error contributions to the output voltage. With a
tight output tolerance (0.5% at 25°C), a very low output voltage temperature coefficient (20 ppm typical),
extremely good line and load regulation (0.3% and 0.4% typical), and remote sensing capability, the parts can be
used as either low-power voltage references or 100-mA regulators.
7.2 LP2950 Functional Block Diagram
INPUT
OUTPUT
+
Error
Amplifier
1.23-V Reference
GND
12
Submit Documentation Feedback
Copyright © 2006–2014, Texas Instruments Incorporated
Product Folder Links: LP2950 LP2951
LP2950, LP2951
www.ti.com
SLVS582I – APRIL 2006 – REVISED NOVEMBER 2014
7.3 LP2951 Functional Block Diagram
FEEDBACK
INPUT
OUTPUT
SENSE
+
Error
Amplifier
SHUTDOWN
VTAP
+
ERROR
60 mV
1.235-V Reference
GND
Submit Documentation Feedback
Copyright © 2006–2014, Texas Instruments Incorporated
Product Folder Links: LP2950 LP2951
13
LP2950, LP2951
SLVS582I – APRIL 2006 – REVISED NOVEMBER 2014
www.ti.com
7.4 Feature Description
7.4.1
ERROR Function (LP2951 Only)
The LP2951 device has a low-voltage detection comparator that outputs a logic low when the output voltage
drops by ≈6% from its nominal value, and outputs a logic high when VOUT has reached ≈95% of its nominal
value. This 95% of nominal figure is obtained by dividing the built-in offset of ≈60 mV by the 1.235-V bandgap
reference, and remains independent of the programmed output voltage. For example, the trip-point threshold
(ERROR output goes high) typically is 4.75 V for a 5-V output and 11.4 V for a 12-V output. Typically, there is a
hysteresis of 15 mV between the thresholds for high and low ERROR output.
A timing diagram is shown in Figure 31 for ERROR vs VOUT (5 V), as VIN is ramped up and down. ERROR
becomes valid (low) when VIN ≈ 1.3 V. When VIN ≈ 5 V, VOUT = 4.75 V, causing ERROR to go high. Because the
dropout voltage is load dependent, the output trip-point threshold is reached at different values of VIN, depending
on the load current. For instance, at higher load current, ERROR goes high at a slightly higher value of VIN, and
vice versa for lower load current. The output-voltage trip point remains at ~4.75 V, regardless of the load. Note
that when VIN ≤ 1.3 V, the ERROR comparator output is turned off and pulled high to its pullup voltage. If VOUT is
used as the pullup voltage, rather than an external 5-V source, ERROR typically is ~1.2 V. In this condition, an
equal resistor divider (10 kΩ is suitable) can be tied to ERROR to divide down the voltage to a valid logic low
during any fault condition, while still enabling a logic high during normal operation.
Output
Voltage
4.75 V
ERROR
5V
Input
Voltage
1.3 V
Figure 31. ERROR Output Timing
Because the ERROR comparator has an open-collector output, an external pullup resistor is required to pull the
output up to VOUT or another supply voltage (up to 30 V). The output of the comparator is rated to sink up to
400 μA. A suitable range of values for the pullup resistor is from 100 kΩ to 1 MΩ. If ERROR is not used, it can
be left open.
14
Submit Documentation Feedback
Copyright © 2006–2014, Texas Instruments Incorporated
Product Folder Links: LP2950 LP2951
LP2950, LP2951
www.ti.com
SLVS582I – APRIL 2006 – REVISED NOVEMBER 2014
Feature Description (continued)
7.4.2 Programming Output Voltage (LP2951 Only)
A unique feature of the LP2951 device is its ability to output either a fixed voltage or an adjustable voltage,
depending on the external pin connections. To output the internally programmed fixed voltage, tie the SENSE pin
to the OUTPUT pin and the FEEDBACK pin to the VTAP pin. Alternatively, a user-programmable voltage ranging
from the internal 1.235-V reference to a 30-V max can be set by using an external resistor divider pair. The
resistor divider is tied to VOUT, and the divided-down voltage is tied directly to FEEDBACK for comparison against
the internal 1.235-V reference. To satisfy the steady-state condition in which its two inputs are equal, the error
amplifier drives the output to equal Equation 1:
R1 ö
æ
VOUT = VREF ´ ç 1 +
÷ - IFBR1
è R2 ø
(1)
Where:
VREF = 1.235 V applied across R2 (see Figure 32)
IFB = FEEDBACK bias current, typically 20 nA
A minimum regulator output current of 1 μA must be maintained. Thus, in an application where a no-load
condition is expected (for example, CMOS circuits in standby), this 1-μA minimum current must be provided by
the resistor pair, effectively imposing a maximum value of R2 = 1.2 MΩ (1.235 V/1.2 MΩ ≉ 1 μA).
IFB = 20 nA introduces an error of ≉0.02% in VOUT. This can be offset by trimming R1. Alternatively, increasing
the divider current makes IFB less significant, thus, reducing its error contribution. For instance, using
R2 = 100 kΩ reduces the error contribution of IFB to 0.17% by increasing the divider current to ≉12 μA. This
increase in the divider current still is small compared to the 600-μA typical quiescent current of the LP2951 under
no load.
VOUT
R1
FEEDBACK
R2
Figure 32. Adjusting the Feedback on the LP2951
7.5 Device Functional Modes
7.5.1 Shutdown Mode
These devices can be placed in shutdown mode with a logic high at the SHUTDOWN pin. Return the logic level
low to restore operation or tie SHUTDOWN to ground if the feature is not being used.
Submit Documentation Feedback
Copyright © 2006–2014, Texas Instruments Incorporated
Product Folder Links: LP2950 LP2951
15
LP2950, LP2951
SLVS582I – APRIL 2006 – REVISED NOVEMBER 2014
www.ti.com
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LP295x devices are used as low-dropout regulators with a wide range of input voltages.
8.2 Typical Application
330 kȍ
VOUT = 5 V
1 PF
VOUT
SENSE
8
2
7
FEEDBACK
LP2951-50
VIN = 12 V
VIN
1
1 PF
SHUTDOWN
3
6
VTAP
GND
4
5
ERROR
Figure 33. 12-V to 5-V Converter
8.2.1 Design Requirements
8.2.1.1 Input Capacitor (CIN)
A 1-μF (tantalum, ceramic, or aluminum) electrolytic capacitor should be placed locally at the input of the LP2950
or LP2951 device if there is, or will be, significant impedance between the ac filter capacitor and the input; for
example, if a battery is used as the input or if the ac filter capacitor is located more than 10 in away. There are
no ESR requirements for this capacitor, and the capacitance can be increased without limit.
8.2.1.2 Output Capacitor (COUT)
As with most PNP LDOs, stability conditions require the output capacitor to have a minimum capacitance and an
ESR that falls within a certain range.
16
Submit Documentation Feedback
Copyright © 2006–2014, Texas Instruments Incorporated
Product Folder Links: LP2950 LP2951
LP2950, LP2951
www.ti.com
SLVS582I – APRIL 2006 – REVISED NOVEMBER 2014
Typical Application (continued)
8.2.2 Detailed Design Procedure
8.2.2.1 Capacitance Value
For VOUT ≥ 5 V, a minimum of 1 μF is required. For lower VOUT, the regulator’s loop gain is running closer to unity
gain and, thus, has lower phase margins. Consequently, a larger capacitance is needed for stability.
For VOUT = 3 V or 3.3 V, a minimum of 2.2 μF is recommended. For worst case, VOUT = 1.23 V (using the ADJ
version), a minimum of 3.3 μF is recommended. COUT can be increased without limit and only improves the
regulator stability and transient response. Regardless of its value, the output capacitor should have a resonant
frequency greater than 500 kHz.
The minimum capacitance values given above are for maximum load current of 100 mA. If the maximum
expected load current is less than 100 mA, then lower values of COUT can be used. For instance, if IOUT < 10 mA,
then only 0.33 μF is required for COUT. For IOUT < 1 mA, 0.1 μF is sufficient for stability requirements. Thus, for a
worst-case condition of 100-mA load and VOUT = VREF = 1.235 V (representing the highest load current and
lowest loop gain), a minimum COUT of 3.3 μF is recommended.
For the LP2950/51, no load stability is inherent in the design — a desirable feature in CMOS circuits that are put
in standby (such as RAM keep-alive applications). If the LP2951 is used with external resistors to set the output
voltage, a minimum load current of 1 μA is recommended through the resistor divider.
8.2.2.2 Capacitor Types
Most tantalum or aluminum electrolytics are suitable for use at the input. Film-type capacitors also work but at
higher cost. When operating at low temperature, care should be taken with aluminum electrolytics, as their
electrolytes often freeze at –30°C. For this reason, solid tantalum capacitors should be used at temperatures
below –25°C.
Ceramic capacitors can be used, but due to their low ESR (as low as 5 mΩ to 10 mΩ), they may not meet the
minimum ESR requirement previously discussed. If a ceramic capacitor is used, a series resistor between
0.1 Ω to 2 Ω must be added to meet the minimum ESR requirement. In addition, ceramic capacitors have one
glaring disadvantage that must be taken into account — a poor temperature coefficient, where the capacitance
can vary significantly with temperature. For instance, a large-value ceramic capacitor (≥ 2.2 μF) can lose more
than half of its capacitance as temperature rises from 25°C to 85°C. Thus, a 2.2-μF capacitor at 25°C drops well
below the minimum COUT required for stability as ambient temperature rises. For this reason, select an output
capacitor that maintains the minimum 2.2 μF required for stability for the entire operating temperature range.
8.2.2.3 CBYPASS: Noise and Stability Improvement
In the LP2951 device, an external FEEDBACK pin directly connected to the error amplifier noninverting input can
allow stray capacitance to cause instability by shunting the error amplifier feedback to GND, especially at high
frequencies. This is worsened if high-value external resistors are used to set the output voltage, because a high
resistance allows the stray capacitance to play a more significant role; i.e., a larger RC time delay is introduced
between the output of the error amplifier and its FEEDBACK input, leading to more phase shift and lower phase
margin. A solution is to add a 100-pF bypass capacitor (CBYPASS) between OUTPUT and FEEDBACK; because
CBYPASS is in parallel with R1, it lowers the impedance seen at FEEDBACK at high frequencies, in effect
offsetting the effect of the parasitic capacitance by providing more feedback at higher frequencies. More
feedback forces the error amplifier to work at a lower loop gain, so COUT should be increased to a minimum of
3.3 μF to improve the regulator’s phase margin.
CBYPASS can be also used to reduce output noise in the LP2951 device. This bypass capacitor reduces the
closed loop gain of the error amplifier at the high frequency, so noise no longer scales with the output voltage.
This improvement is more noticeable with higher output voltages, where loop gain reduction is greatest. A
suitable CBYPASS is calculated as shown in Equation 2:
f(CBYPASS) ; 200 Hz ® C(BYPASS) =
1
2p ´ R1´ 200 Hz
(2)
On the 3-pin LP2950 device, noise reduction can be achieved by increasing the output capacitor, which causes
the regulator bandwidth to be reduced, thus eliminating high-frequency noise. However, this method is relatively
inefficient, as increasing COUT from 1 μF to 220 μF only reduces the regulator’s output noise from
430 μV to 160 μV (over a 100-kHz bandwidth).
Submit Documentation Feedback
Copyright © 2006–2014, Texas Instruments Incorporated
Product Folder Links: LP2950 LP2951
17
LP2950, LP2951
SLVS582I – APRIL 2006 – REVISED NOVEMBER 2014
www.ti.com
Typical Application (continued)
8.2.2.4 ESR Range
The regulator control loop relies on the ESR of the output capacitor to provide a zero to add sufficient phase
margin to ensure unconditional regulator stability; this requires the closed-loop gain to intersect the open-loop
response in a region where the open-loop gain rolls off at 20 dB/decade. This ensures that the phase is always
less than 180° (phase margin greater than 0°) at unity gain. Thus, a minimum-maximum range for the ESR must
be observed.
The upper limit of this ESR range is established by the fact that an ESR that is too high could result in the zero
occurring too soon, causing the gain to roll off too slowly. This, in turn, allows a third pole to appear before unity
gain and introduces enough phase shift to cause instability. This typically limits the maximum ESR to
approximately 5 Ω.
Conversely, the lower limit of the ESR range is tied to the fact that an ESR that is too low shifts the zero too far
out, past unity gain, which allows the gain to roll off at 40 dB/decade at unity gain, resulting in a phase shift of
greater than 180°. Typically, this limits the minimum ESR to approximately 20 mΩ to 30 mΩ.
For specific ESR requirements, see Typical Characteristics.
8.2.3 Application Curves
Output Voltage
100 mV/div
Output Load
100 mA/div
Figure 34. Load Transient Response vs Time (VOUT = 5 V, CL = 1 µF)
18
Submit Documentation Feedback
Copyright © 2006–2014, Texas Instruments Incorporated
Product Folder Links: LP2950 LP2951
LP2950, LP2951
www.ti.com
SLVS582I – APRIL 2006 – REVISED NOVEMBER 2014
9 Power Supply Recommendations
Maximum input voltage should be limited to 30 V for proper operation. Place input and output capacitors as close
to the device as possible to take advantage of their high frequency noise filtering properties.
10 Layout
10.1 Layout Guidelines
•
•
Make sure that traces on the input and outputs of the device are wide enough to handle the desired currents.
For this device, the output trace will need to be larger in order to accommodate the larger available current.
Place input and output capacitors as close to the device as possible to take advantage of their high frequency
noise filtering properties.
10.2 Layout Example
1
1 PF
8
2
7
LP2951-50
3
6
4
5
1 PF
ERROR can be left floating
if not used
Figure 35. LP2951 Layout Example (D or P Package)
11 Device and Documentation Support
11.1 Trademarks
All trademarks are the property of their respective owners.
11.2 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.3 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2006–2014, Texas Instruments Incorporated
Product Folder Links: LP2950 LP2951
19
PACKAGE OPTION ADDENDUM
www.ti.com
16-Oct-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LP2950-30LP
ACTIVE
TO-92
LP
3
1000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
-40 to 125
KY5030
LP2950-30LPR
ACTIVE
TO-92
LP
3
2000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
-40 to 125
KY5030
LP2950-30LPRE3
ACTIVE
TO-92
LP
3
2000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
-40 to 125
KY5030
LP2950-33LPE3
ACTIVE
TO-92
LP
3
1000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
-40 to 125
KY5033
LP2950-33LPRE3
ACTIVE
TO-92
LP
3
2000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
0 to 0
KY5033
LP2950-50LPRE3
ACTIVE
TO-92
LP
3
2000
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
-40 to 125
KY5050
LP2951-30D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
KY5130
LP2951-30DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
KY5130
LP2951-30DRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
KY5130
LP2951-30DRGR
ACTIVE
SON
DRG
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
ZUD
LP2951-33D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
KY5133
LP2951-33DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
KY5133
LP2951-33DRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
KY5133
LP2951-33DRGR
ACTIVE
SON
DRG
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
ZUE
LP2951-50D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
KY5150
LP2951-50DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
KY5150
LP2951-50DRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
KY5150
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
16-Oct-2014
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LP2951-50DRGR
ACTIVE
SON
DRG
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
ZUF
LP2951D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
LP2951
LP2951DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
LP2951
LP2951DRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
LP2951
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
16-Oct-2014
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LP2951-33, LP2951-50 :
• Automotive: LP2951-33-Q1, LP2951-50-Q1
NOTE: Qualified Version Definitions:
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Jul-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
LP2951-30DR
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
LP2951-30DRGR
SON
DRG
8
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
LP2951-33DR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
LP2951-33DRGR
SON
DRG
8
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
LP2951-50DR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
LP2951-50DRGR
SON
DRG
8
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
LP2951DR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Jul-2015
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LP2951-30DR
SOIC
D
8
2500
340.5
338.1
20.6
LP2951-30DRGR
SON
DRG
8
3000
367.0
367.0
35.0
LP2951-33DR
SOIC
D
8
2500
340.5
338.1
20.6
LP2951-33DRGR
SON
DRG
8
3000
367.0
367.0
35.0
LP2951-50DR
SOIC
D
8
2500
340.5
338.1
20.6
LP2951-50DRGR
SON
DRG
8
3000
367.0
367.0
35.0
LP2951DR
SOIC
D
8
2500
340.5
338.1
20.6
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated