Document 428-1 Shielded Power Inductors – LPS3010 • Ultra small 3.0 × 3.0 mm footprint; less than 1.0 mm tall • Very low DCR; excellent current handling Core material Ferrite Core and winding loss See www.coilcraft.com/coreloss Terminations RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight 25 – 32 mg Ambient temperature –40°C to +85°C with Irms current, +85°C to +125°C with derated current Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 1000/7″ reel; 3500/13″ reel; Plastic tape: 12 mm wide, 0.23 mm thick, 8 mm pocket spacing, 1.4 mm pocket depth Recommended pick and place nozzle OD: 3 mm; ID: ≤ 1.5 mm PCB washing Tested with pure water or alcohol only. For other solvents, see Doc787_PCB_Washing.pdf Isat (A)5 Irms (A)6 DCR SRF Inductance2 max3 typ4 10% 20% 30% 20°C 40°C Part number1 ±20% (µH) (Ohms) (MHz) drop drop drop rise rise LPS3010-471ML_ LPS3010-681ML_ LPS3010-102ML_ LPS3010-152ML_ LPS3010-182ML_ 0.47 0.68 1.0 1.5 1.8 0.070 0.080 0.085 0.120 0.150 370 270 230 165 150 1.8 1.6 1.5 1.3 1.2 1.9 1.7 1.6 1.4 1.2 2.0 1.7 1.6 1.4 1.3 1.3 1.3 1.1 1.05 1.00 1.80 1.75 1.50 1.40 1.40 LPS3010-222ML_ LPS3010-332ML_ LPS3010-472ML_ LPS3010-562ML_ LPS3010-682ML_ 2.2 3.3 4.7 5.6 6.8 0.220 0.220 0.300 0.400 0.450 130 110 92 80 70 1.3 0.83 0.72 0.67 0.61 1.4 0.88 0.75 0.69 0.63 1.4 0.90 0.77 0.71 0.64 0.90 0.85 0.70 0.60 0.56 1.10 1.10 0.95 0.78 0.74 LPS3010-822ML_ LPS3010-103ML_ LPS3010-123ML_ LPS3010-153ML_ LPS3010-183ML_ 8.2 10 12 15 18 0.520 0.540 0.700 0.950 1.10 62 58 47 43 40 0.56 0.50 0.46 0.41 0.38 0.59 0.53 0.49 0.43 0.40 0.59 0.55 0.50 0.44 0.41 0.53 0.48 0.44 0.37 0.33 0.70 0.64 0.58 0.48 0.47 LPS3010-223ML_ LPS3010-333ML_ LPS3010-473ML_ LPS3010-683ML_ LPS3010-104ML_ 22 33 47 68 100 1.20 2.00 3.20 3.50 5.25 36 27 21 21 14 0.32 0.25 0.23 0.20 0.14 0.35 0.27 0.24 0.21 0.16 0.36 0.28 0.25 0.22 0.17 0.30 0.26 0.22 0.20 0.18 0.41 0.35 0.31 0.28 0.24 LPS3010-124ML_ LPS3010-154ML_ LPS3010-184ML_ LPS3010-224ML_ LPS3010-334ML_ 120 150 180 220 330 6.10 9.15 10.1 12.5 18.5 12 11 9 8 7 0.13 0.13 0.11 0.10 0.10 0.15 0.14 0.12 0.11 0.105 0.15 0.14 0.13 0.12 0.115 0.14 0.13 0.11 0.095 0.085 0.19 0.17 0.15 0.13 0.11 1. Please specify termination and packaging codes: LPS3010-223MLC Termination: L = RoHS compliant silver-palladiumplatinum-glass frit. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tinlead (63/37). Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic tape (1000 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D = 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (3500 parts per full reel). 2. Inductance tested at 100 kHz, 0.1 Vrms using an Agilent/HP 4192A. Inductance at 1 MHz is the same for parts with SRF ≥10 MHz. 3. DCR measured on a micro-ohmmeter. 4. SRF measured using an Agilent/HP 8753ES or equivalent. 5. DC current that causes the specified inductance drop from its value without current. 6. Current that causes the specified temperature rise from 25°C ambient. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. • Coilcraft Designer’s Kit C392 contains samples of 0.80 µH to 33 µH parts (3 each) from LPS3008, LPS3010 and LPS3015. Kit C401 contains samples of 0.56 µH to 33 µH parts (3 each) from LPS4012 and LPS4018. Kit C402 contains samples of 220 µH to 3300 µH parts (3 each) from all five series. For details of kit contents and to order, contact Coilcraft or visit http://order.coilcraft.com. US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 428-1 Revised 11/22/11 © Coilcraft Inc. 2013 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information. Document 428-2 Shielded SMT Power Inductors – LPS3010 Series L vs Frequency L vs Current 1000 1000 330 µH 100 68 µH Inductance (µH) Inductance (µH) 330 µH 33 µH 6.8 µH 10 3.3 µH 1 0.1 0.68 µH 0.01 0.1 1 10 Frequency (MHz) Typical Current Derating 100 68 µH 33 µH 6.8 µH 10 3.3 µH 1 0.1 0.68 µH 0.01 0.1 Current (A) 1 10 0.116 ±0.003* 2,95 ±0,076 120 0.116 ±0.003* 2,95 ±0,076 100 123X 90 80 70 Dash number 60 Winding direction Internal code Recommended Land Pattern 50 0.035 ±0.004 ** 0,9 ±0,1 40 30 20 25°C Percent of rated Current 110 Isat Irms 10 0 -40 -20 0 20 40 60 80 100 120 140 0.020 0,51 0.045 1,14 0.025 0,64 Ambient temperature (°C) 0.035 0,89 0.130 3,30 0.040 1,02 are of the case not * Dimensions including the termination. For maximum overall dimensions including the termination, add 0.005 in / 0,13 mm. 0.130 3,30 **For optional tin-lead and tin-silver-copper terminations, dimensions are for the mounted part. Dimensions before mounting can be an additional 0.005 inch (0,13 mm). Dimensions are in inches mm US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 428-2 Revised 11/22/11 © Coilcraft Inc. 2013 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information.