NLU3G17 Triple Non-Inverting Schmitt-Trigger Buffer The NLU3G17 MiniGatet is an advanced high−speed CMOS triple non−inverting Schmitt−trigger buffer in ultra−small footprint. The NLU3G17 input and output structures provide protection when voltages up to 7.0 V are applied, regardless of the supply voltage. The NLU3G17 can be used to enhance noise immunity or to square up slowly changing waveforms. www.onsemi.com MARKING DIAGRAMS Features • • • • • • • 8 High Speed: tPD = 4.0 ns (Typ) @ VCC = 5.0 V Low Power Dissipation: ICC = 1 mA (Max) at TA = 25°C Power Down Protection Provided on inputs Balanced Propagation Delays Overvoltage Tolerant (OVT) Input and Output Pins Ultra−Small Packages These are Pb−Free Devices IN A1 8 1 1 UZM G UDFN8 CASE 517AJ UDFN8 1.45 x 1.0 CASE 517BZ 1 UDFN8 1.6 x 1.0 CASE 517BY 1 XM XM VCC OUT Y3 2 7 OUT Y1 IN A2 3 6 IN A3 GND 4 5 OUT Y2 UDFN8 1.95 x 1.0 CASE 517CA XM 1 UZ, D or LX = Specific Device Code M = Date Code G = Pb−Free Package ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. Figure 1. Pinout (Top View) IN A1 1 OUT Y1 IN A2 1 OUT Y2 IN A3 1 OUT Y3 Figure 2. Logic Symbol FUNCTION TABLE A L H 1 IN A1 2 OUT Y3 3 IN A2 4 GND 5 OUT Y2 Y 6 IN A3 L H 7 OUT Y1 8 VCC © Semiconductor Components Industries, LLC, 2016 July, 2016 − Rev. 4 PIN ASSIGNMENT 1 Publication Order Number: NLU3G17/D NLU3G17 MAXIMUM RATINGS Symbol Value Unit VCC DC Supply Voltage −0.5 to +7.0 V VIN DC Input Voltage −0.5 to +7.0 V DC Output Voltage −0.5 to +7.0 V VIN < GND −20 mA VOUT < GND ±20 mA VOUT Parameter IIK DC Input Diode Current IOK DC Output Diode Current IO DC Output Source/Sink Current ±12.5 mA ICC DC Supply Current Per Supply Pin ±25 mA IGND DC Ground Current per Ground Pin ±25 mA TSTG Storage Temperature Range −65 to +150 °C TL Lead Temperature, 1 mm from Case for 10 Seconds 260 °C TJ Junction Temperature Under Bias 150 °C MSL FR ILATCHUP Moisture Sensitivity Level 1 Flammability Rating Oxygen Index: 28 to 34 Latchup Performance Above VCC and Below GND at 125°C (Note 2) UL 94 V−0 @ 0.125 in ±500 mA Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm−by−1 inch, 2 ounce copper trace no air flow. 2. Tested to EIA / JESD78. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit 1.65 5.5 V VCC Positive DC Supply Voltage VIN Digital Input Voltage 0 5.5 V Output Voltage 0 5.5 V −55 +125 °C 0 0 No Limit No Limit ns/V VOUT TA Operating Free−Air Temperature Dt/DV Input Transition Rise or Fall Rate VCC = 3.3 V ± 0.3 V VCC = 5.0 V ± 0.5 V www.onsemi.com 2 NLU3G17 DC ELECTRICAL CHARACTERISTICS Symbol Parameter Conditions TA = 25 5C TA = +855C VCC (V) Min Typ Max Min VT+ Positive Threshold Voltage 3.0 4.5 5.5 1.85 2.86 3.50 2.0 3.0 3.6 2.2 3.15 3.85 VT− Negative Threshold Voltage 3.0 4.5 5.5 0.9 1.35 1.65 1.5 2.3 2.9 1.65 2.46 3.05 0.9 1.35 1.65 VH Hysteresis Voltage 3.0 4.5 5.5 0.30 0.40 0.50 0.57 0.67 0.74 1.20 1.40 1.60 0.30 0.40 0.50 VOH Minimum High−Level Output Voltage 2.0 3.0 4.5 1.9 2.9 4.4 2.0 3.0 4.5 3.0 4.5 2.58 3.94 VOL Maximum Low−Level Output Voltage VIN w VT+MAX IOH = −50 mA VIN w VT+MAX IOH = −4 mA IOH = −8 mA VIN v VT−MIN IOL = 50 mA VIN v VT−MIN IOL = 4 mA IOL = 8 mA 2.0 3.0 4.5 0 0 0 Max TA = −555C to +1255C Min 2.2 3.15 3.85 Max Unit 2.2 3.15 3.85 V 0.9 1.35 1.65 1.20 1.40 1.60 0.30 0.40 0.50 1.9 2.9 4.4 1.9 2.9 4.4 2.48 3.80 2.34 3.66 V 1.20 1.40 1.60 V V 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 0.36 0.36 0.44 0.44 0.52 0.52 V IIN Input Leakage Current 0 v VIN v 5.5 V 0 to 5.5 ±0.1 ±1.0 ±1.0 mA ICC Quiescent Supply Current 0 v VIN v VCC 5.5 1.0 10 40 mA AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 ns) Symbol tPLH, tPHL Parameter Propagation Delay, Input A to Output Y CIN Input Capacitance CPD Power Dissipation Capacitance (Note 3) VCC (V) Test Condition TA = 25 5C Min TA = +855C Typ Max Min TA = −555C to +1255C Max Min Max Unit ns 3.0 to 3.6 CL = 15 pF 7.0 12.8 1.0 15 1.0 17 CL = 50 pF 8.5 16.3 1.0 18.5 1.0 20.5 4.5 to 5.5 CL = 15 pF 4.0 8.6 1.0 10 1.0 11.5 CL = 50 pF 5.5 10.6 1.0 12 1.0 13.5 5.0 10 5.0 7.0 10 10 pF pF 3. CPD is defined as the value of the internal equivalent capacitance which is calculated from the dynamic operating current consumption without load. Average operating current can be obtained by the equation ICC(OPR) = CPD • VCC • fin + ICC. CPD is used to determine the no−load dynamic power consumption: PD = CPD • VCC2 • fin + ICC • VCC. www.onsemi.com 3 NLU3G17 OUTPUT INPUT VCC A or B 50% RL CL GND tPLH tPHL Y 50% VCC A 1−MHz square input wave is recommended for propagation delay tests. Figure 4. Test Circuit Figure 3. Switching Waveforms VH VCC VT+ VT− VIN VCC VH VT+ VT− VIN GND GND VOH VOH VOUT Vout VOL VOL (a) A Schmitt−Trigger Squares Up Inputs With Slow Rise and Fall Times (b) A Schmitt−Trigger Offers Maximum Noise Immunity Figure 5. Typical Schmitt−Trigger Applications ORDERING INFORMATION Package Shipping† UDFN8 (Pb−Free) 3000 / Tape & Reel NLU3G17DMUTCG UDFN8, 1.95 x 1.0, 0.5P (Pb−Free) 3000 / Tape & Reel NLU3G17EMUTCG UDFN8, 1.6 x 1.0, 0.4P (Pb−Free) 3000 / Tape & Reel NLU3G17FMUTCG UDFN8, 1.45 x 1.0, 0.35P (Pb−Free) 3000 / Tape & Reel Device NLU3G17MUTAG †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. www.onsemi.com 4 NLU3G17 PACKAGE DIMENSIONS UDFN8 1.6x1.0, 0.4P CASE 517BY ISSUE O PIN ONE REFERENCE 0.10 C 2X 2X ÉÉÉ ÉÉÉ ÉÉÉ 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.20 MM FROM TERMINAL TIP. 4. PACKAGE DIMENSIONS EXCLUSIVE OF BURRS AND MOLD FLASH. A B D E DIM A A1 A3 b D E e L L1 TOP VIEW A3 0.05 C A 0.05 C A1 SIDE VIEW C RECOMMENDED SOLDERING FOOTPRINT* SEATING PLANE 7X e/2 0.49 e 1 7X MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.13 REF 0.15 0.25 1.60 BSC 1.00 BSC 0.40 BSC 0.25 0.35 0.30 0.40 L 8X 0.26 4 L1 1.24 8 5 BOTTOM VIEW 8X b 0.10 M C A B 0.05 M C 0.53 1 PKG OUTLINE 0.40 PITCH DIMENSIONS: MILLIMETERS NOTE 3 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 5 NLU3G17 PACKAGE DIMENSIONS UDFN8 1.45x1.0, 0.35P CASE 517BZ ISSUE O PIN ONE REFERENCE 0.10 C 2X 2X 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.20 MM FROM TERMINAL TIP. 4. PACKAGE DIMENSIONS EXCLUSIVE OF BURRS AND MOLD FLASH. A B D ÉÉ ÉÉ ÉÉ E DIM A A1 A3 b D E e L L1 TOP VIEW A3 0.05 C A 0.05 C A1 SIDE VIEW C RECOMMENDED SOLDERING FOOTPRINT* SEATING PLANE 7X 0.48 e/2 e 1 7X MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.13 REF 0.15 0.25 1.45 BSC 1.00 BSC 0.35 BSC 0.25 0.35 0.30 0.40 8X 0.22 L 4 L1 1.18 8 5 BOTTOM VIEW 8X 0.53 b 0.10 M C A B 0.05 M C 1 PKG OUTLINE NOTE 3 DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 6 0.35 PITCH NLU3G17 PACKAGE DIMENSIONS UDFN8 1.95x1.0, 0.5P CASE 517CA ISSUE O PIN ONE REFERENCE 0.10 C 2X 2X ÉÉÉ ÉÉÉ ÉÉÉ 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.20 MM FROM TERMINAL TIP. 4. PACKAGE DIMENSIONS EXCLUSIVE OF BURRS AND MOLD FLASH. A B D E DIM A A1 A3 b D E e L L1 TOP VIEW A3 0.05 C A 0.05 C A1 SIDE VIEW C RECOMMENDED SOLDERING FOOTPRINT* SEATING PLANE 7X e/2 0.49 e 7X MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.13 REF 0.15 0.25 1.95 BSC 1.00 BSC 0.50 BSC 0.25 0.35 0.30 0.40 L 8X 0.30 4 1 L1 1.24 8 5 BOTTOM VIEW 8X b 0.10 M C A B 0.05 M C 0.54 NOTE 3 0.50 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 7 1 PKG OUTLINE NLU3G17 PACKAGE DIMENSIONS UDFN8 1.8x1.2, 0.4P CASE 517AJ ISSUE O PIN ONE REFERENCE NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM TERMINAL TIP. 4. MOLD FLASH ALLOWED ON TERMINALS ALONG EDGE OF PACKAGE. FLASH MAY NOT EXCEED 0.03 ONTO BOTTOM SURFACE OF TERMINALS. 5. DETAIL A SHOWS OPTIONAL CONSTRUCTION FOR TERMINALS. A B D 0.10 C ÉÉÉ ÉÉÉ L1 E DETAIL A NOTE 5 0.10 C TOP VIEW (A3) 0.05 C DIM A A1 A3 b b2 D E e L L1 L2 A 0.05 C SIDE VIEW A1 e/2 e (b2) C DETAIL A 8X 1 SEATING PLANE L 4 MOUNTING FOOTPRINT SOLDERMASK DEFINED (L2) 8 5 MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.127 REF 0.15 0.25 0.30 REF 1.80 BSC 1.20 BSC 0.40 BSC 0.45 0.55 0.00 0.03 0.40 REF 8X b BOTTOM VIEW 8X 0.10 M C A B 0.05 M C 0.66 7X 0.22 NOTE 3 1.50 1 0.32 0.40 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. MiniGate is a trademark of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 8 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NLU3G17/D