ProLite 3W SMD Emitter BTP3-99XXCG-XX-X/W Package Dimension Features Highest Lumen Per Watt Long Operational Life White Housing Superior ESD Protection Instant Light (less than 100ns) Compatible to Luxeon’s “Lambertian” True SMD Emitter IR Reflow Soldering Process Applications Accent Light/Down Light/Spot Light Automotive Exterior/Interior Light Large Area LCD Backlights Marine/Miner’s Lighting Portable Flashlight/ General Lighting Note: Lens is low dome profile Tolerance: ± see spec Unit: mm Optical Characteristics at TJ=25ºC, IF=700mA PART NUMBER Emitting Color LED Chip Material Lens Color Wavelength (nm) CCT (K) Range Drive Luminous VIEW Voltage Flux (lm) ANGLE @ 700mA @700mA 2θ1/2 Typ. (deg) Min Max Typ. Water Clear 620 635 2.40V 60 lm Water Clear 610 620 2.40V 72 lm BTP3-99NRCG-XX-X/W Normal Red BTP3-99AMCG-XX-X/W Amber BTP3-99YECG-XX-X/W Yellow Water Clear 585 595 2.40V 60 lm BTP3-99BLCG-XX-X/W Blue Water Clear 460 475 3.50V 20 lm BTP3-99PGCG-XX-X/W Green Water Clear 520 540 3.50V 60 lm Water Clear 2800K 3800K 3.50V 40 lm Water Clear 5000K 8000K 3.50V 60 lm BTP3-99WWCG-XX-X/W Warm White BTP3-99WHCG-XX-X/W White AlInGaP AlInGaN 140 Notes: 1) Picture for illustration purpose only. Please refer to outline dimension for actual package size. 2) Flux is measured with the accuracy of ±15%. Please refer to Flux Selection Guide 3) CCT is measured with the accuracy of ± 400K. Please refer to CCT Selection Guide 4) VF is measured with the accuracy of ± 0.15V. Please refer to VF Selection Guide Part No.: BTP3-99XXCG-XX-X/W Rev1.2005 Page 1 of 10 DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com ProLite 3W SMD Emitter BTP3-99XXCG-XX-X/W Absolute Maximum Ratings at TJ=25ºC Parameter Red/Amber/Yellow White/Blue/Green 2.17 2.80 700 700 1000 1000 Average Forward Current (mA) 700 700 Reverse Voltage (V) 5 5 Reverse Current (uA) 50 50 16,000 16,000 120 135 Thermal Resistance Junction to Board (°C/W) 13 13 Temperature Coefficient of VF (mV/°C) -2 -2 Storage Temperature (°C) -40 to +105 -40 to +105 Operating Temperature (°C) -40 to +105 -40 to +105 Power Dissipation (W) [1] DC Forward Current (mA) Peak Pulsed Forward Current (mA) [4] ESD Sensitivity (V) [2] LED Junction Temperature at 350mA (°C) [3] Lead Soldering Temperature (°C)[4] 260°C for 5 seconds max 260°C for 5 seconds max Application Notes: 1. Proper forward current must be observed to maintain the junction temperature below maximum rating 2. Although all products listed are class one ESD protection (+/- 16KV by HBM mode), care must be fully taken when handling products 3. Specification is subjected to change for improvements without notice. 4. Test conditions: tp≤10us, duty cycle = 0.005 5. CAUTION: When lighting up, the emitter will become very hot if it is not attached to a heat sink. Please provide proper heat management to prevent damage to the emitter. Part No.: BTP3-99XXCG-XX-X/W Rev1.2005 Page 2 of 10 DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com ProLite 3W SMD Emitter BTP3-99XXCG-XX-X/W CCT, Flux and VF Selection Guide (@TJ=25ºC, IF=700mA) BTP3-99XXCG-XX-X/W White Housing Wavelength Ranks Selection Color Blue Green Red Amber Yellow Bin B5 B6 B7 XX G6 G7 G8 G9 XX XX XX XX Flux Ranks Selection λD(nm) Min Max 460 465 465 470 470 475 460 – 475 515 520 520 525 525 530 530 535 515 – 535 620 – 630 610 – 620 585 – 595 CCT Ranks Selection Color Temp Warm White White Bin 00 01 XX 02 03 04 XX Color Blue Red Amber Yellow Green White Bin Flux (lumens) K 8~10 L 10~14 M 14~18 X Default Full Range Q 30~39 R 39~50 S 50~65 T 65~85 U 85~111 X Default Full Range VF Ranks Selection CCT(K) Min Max 2800 3300 3300 3800 2800K – 3800K 5000 6000 6000 7000 7000 8000 5000K – 8000K Color Red Amber Yellow White Blue Green Bin VF (V) Min Max V04 V05 V06 V07 VXX(Full) V08 V09 V10 V11 V12 VXX(Full) 2.0 2.2 2.2 2.4 2.4 2.6 2.6 2.8 2.0~2.8 2.8 3.0 3.0 3.2 3.2 3.4 3.4 3.6 3.6 3.8 2.8~3.8 (Please specify on order, otherwise, default full range of VF) Part No.: BTP3-99XXCG-XX-X/W Rev1.2005 Page 3 of 10 DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com ProLite 3W SMD Emitter BTP3-99XXCG-XX-X/W Typical Electro-Optical Characteristics Curves Fig. 1 Forward Current vs Ambient Temperature (Green, Blue and White) Fig. 2 Forward Current vs Ambient Temperature (Red, Amber and Yellow) Part No.: BTP3-99XXCG-XX-X/W Rev1.2005 Page 4 of 10 DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com ProLite 3W SMD Emitter BTP3-99XXCG-XX-X/W Part No.: BTP3-99XXCG-XX-X/W Rev1.2005 Page 5 of 10 DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com ProLite 3W SMD Emitter BTP3-99XXCG-XX-X/W Typical Electro-Optical Characteristics Curves Fig. 5a Relative Light Output vs Junction Temperature Fig. 5b Relative Light Output vs Junction Temperature Part No.: BTP3-99XXCG-XX-X/W Rev1.2005 Page 6 of 10 DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com ProLite 3W SMD Emitter BTP3-99XXCG-XX-X/W Relative Intensity(%) Typical Electro-Optical Characteristics Curves 100 90 80 70 60 50 40 30 20 10 0 -100 -80 -60 -40 -20 0 20 40 60 80 100 Angular Displacement(Degree) Fig. 6 Typical Radiation Pattern Recommended Solder Pad Layout Fig. 7 Recommended Solder Pads Dimension Part No.: BTP3-99XXCG-XX-X/W Rev1.2005 Page 7 of 10 DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com ProLite 3W SMD Emitter BTP3-99XXCG-XX-X/W Tape and Reel Packaging Dimension Part No.: BTP3-99XXCG-XX-X/W Rev1.2005 Page 8 of 10 DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com ProLite 3W SMD Emitter BTP3-99XXCG-XX-X/W Recommended IR Reflow Conditions Reflow Soldering Lead Solder Pre-heat Pre-heat time Peak Temperature Soldering Time Conditions Lead-Free Solder 120~150ºC 120 sec Max 180~200ºC 120 sec Max 240ºC Max 260ºC Max 10 sec Max 10 sec Max Refer to Temperature profile B (N2 reflow is recommended) Refer to Temperature profile A Temperature Profile A (Surface of MCPCB) Temperature Profile B (Surface of MCPCB) Part No.: BTP3-99XXCG-XX-X/W Rev1.2005 Page 9 of 10 DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com ProLite 3W SMD Emitter BTP3-99XXCG-XX-X/W IR Reflow Process Notes z Occasionally there is a brightness decrease due to the influence of heat or ambient during air reflow. It is recommended that customer use nitrogen reflow method. z Repairing should not be done after the LEDs have been soldered. When repairing is required, double-head soldering iron should be used. Customer should confirm whether the characteristics of the LEDs will or will not damaged before carrying out the repair. z Reflow soldering should not be done more than two times z When soldering, do not put stress on the LEDs during heating. z After soldering, do not warp the circuit board. Manual Hand Soldering Notes z For prototype builds or small production runs, it is possible to place and solder the emitters. z It is recommended to hand solder the leads and slug with a solder tip temperature of 230ºC for less than 10seconds. This profile ensures a junction temperature below the maximum of 120ºC, avoiding damage to the emitter or to the MCPCB dielectric layer. Damage dielectric layer can cause a short circuit in the array. Other Important Notes: z The information contained herein is presented only as a Guide for the application of our products. Brilliance Technologies assumes no responsibility for any infringement of intellectual property or other rights of the third parties which may result from its use. z Brilliance Technologies continually improves the quality of our products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsible of the customer, when using Brilliance Technologies products, to comply with the standard of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such Brilliance Technologies products cause loss of human life, bodily injury or damage to property. z Brilliance Technologies products listed in this data sheet are intended for usage in general electronics and/or non-commercial or industrial lighting products. These products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury. z In developing your design, please ensure that Brilliance Technologies products are used within specified operating ranges as set forth in the most recent Brilliance Technologies data sheets. BT-Rev. 1.0A20050119 Specifications are subject to change for improvement without notice. Copyright © 2003 Brilliance Technologies Co., Ltd. All rights reserved. Part No.: BTP3-99XXCG-XX-X/W Rev1.2005 Page 10 of 10 DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com