Document 284-1 SMT Power Inductors - DO5010H Series • Irms ratings up to 15 A; saturation currents up to 30 A • Heavy gauge wire for low DC resistance Designer’s Kit C355 contains 3 of each part Core material Ferrite Core and winding loss See www.coilcraft.com/coreloss Terminations RoHS compliant tin-silver over copper. Other terminations available at additional cost. Weight 3.2 – 4.0 g Ambient temperature –40°C to +85°C with Irms current, +85°C to +125°C with derated current Storage temperature Component: –40°C to +125°C. Packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 250 per 13″ reel Plastic tape: 32 mm wide, 0.38 mm thick, 24 mm pocket spacing, 7.8 mm pocket depth PCB washing Only pure water or alcohol recommended Part Number1 DO5010H-781ML_ DO5010H-152ML_ DO5010H-222ML_ DO5010H-332ML_ DO5010H-392ML_ DO5010H-472ML_ DO5010H-602ML_ DO5010H-782ML_ DO5010H-103ML_ DO5010H-123ML_ DO5010H-153ML_ DO5010H-223ML_ DO5010H-333ML_ DO5010H-473ML_ DO5010H-683ML_ DO5010H-104ML_ DO5010H-154ML_ DO5010H-224ML_ DO5010H-334ML_ DO5010H-474ML_ DO5010H-684ML_ DO5010H-105ML_ Inductance2 ±20% (µH) 0.78 1.5 2.2 3.3 3.9 4.7 6.0 7.8 10 12 15 22 33 47 68 100 150 220 330 470 680 1000 DCR max (mOhm) 2.6 4.0 6.1 8.6 10 14 17 18 26 28 32 47 66 86 130 190 250 380 560 850 1100 1800 SRF typ3 (MHz) 156 100 75 60 55 40 35 35 28 26 20 20 15 9 8 7 6 5 4 3 2.5 2.0 1. When ordering, please specify termination and packaging codes: Isat4 (A) 30 25 20 17 15 13 12 11 10 8.5 8.0 7.0 5.5 4.5 3.5 3.0 2.6 2.4 1.9 1.4 1.2 1.0 Irms5 (A) 15 15 12 10 9.0 8.4 7.5 7.5 6.0 5.2 4.4 3.5 3.0 2.6 2.3 1.8 1.5 1.2 1.0 0.82 0.72 0.56 DO5010H-105MLD Termination: L = RoHS compliant tin-silver over copper. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: D = 13″ machine-ready reel. EIA-481 embossed plastic tape. B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Inductance tested at 100 kHz, 0.1 Vrms using an Agilent/HP 4284A LCR meter or equivalent. 3. SRF measured using Agilent/HP 8753D network analyzer. 4. DC current at which the inductance drops 10% (typ) from its value without current. 5. Current that causes a 40°C temperature rise from 25°C ambient. 6. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 Document 284-1 Revised 10/14/08 Document 284-2 SMT Power Inductors - DO5010H Series Typical L vs Frequency Typical L vs Current 10000 10000 1000 Inductance (µH) Inductance (µH) 1000 µH 1000 µH 1000 100 µH 100 10 µH 10 10 µH 10 0.78 µH 1 0.78 µH 1 100 µH 100 0.1 0.1 0.01 1 0.1 10 0.1 10 1 0.500 12,70 Irms Derating 120 Note: Maximum height: 0.315 for -781 to -153 8,00 0.300 for -223 to -683 7,62 0.280 for -104 to -105 7,11 Note 110 100 0.730 max 18,54 90 0.561 min 14,25 80 0.075 1,90 70 60 0.250 6,35 0.600 max 15,24 50 40 25°C Percent of rated Irms 100 Current (A) Frequency (MHz) 30 0.065 max 1,65 20 Recommended Land Pattern 0.710 max 18,03 10 Internal code 0 -40 -20 0 20 40 60 80 100 0.626 15,90 0.200 max 5,08 Dash number 120 140 Ambient temperature (°C) XXX X Part Marking Part marking since Feb. 2005. Parts manufactured prior to that date may have color dots. Visit www.coilcraft.com/colrpowr.cfm for details. Dimensions are in inches mm Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 Document 284-2 Revised 10/14/08