PD-97593B (5962F1023505K) IRUH330133BK Radiation Hardended Ultra Low Dropout IRUH330133BP Fixed Positive Linear Regulator +5.0VIN to +3.3VOUT @3.0A Product Summary Part Number IRUH330133BK IRUH330133BP Dropout IO VIN VOUT 0.4V 3.0A 5.0V 3.3V MO-078AA Features Description The IRUH330133 is a space qualified, ultra low dropout linear regulator designed specifically for applications requiring high reliability, low noise and radiation hardness. n Silicon On Insulator (SOI) CMOS Regulator n n n n n n n n n n Absolute Maximum Ratings Parameter Power Dissipation @ TC = 125°C Maximum Output Current @ Maximum IC, CMOS Latch-Up Immune, Inherently Rad Hard Total Dose Capability up to 300Krads(Si) (Condition A); Tested to 500Krad (Si) ELDRS up to 100Krad(Si) (Condition D) SEU Immune up to LET = 80 MeV*cm2/mg Space Level Screened Fast Transient Response Timed Latch-Off Over-Current Protection Internal Thermal Protection On/Off Control via Shutdown Pin, Power Sequencing Easily Implemented Isolated Hermetic MO-078 Package Ensures Higher Reliability This part is also available in 8-Lead Flat Pack Package as IRUH330133AK / IRUH330133AP Symbol Min. Max. Units PD - 25 W A Power Dissipation with no Derating Non-Operating Input Voltage IO - See Fig 4 VIN -0.3 +8.0 Operating Input Voltage VIN 2.9 6.4 GND VSHDN -0.3 -0.3 0.3 VIN + 0.3 Ground Shutdown Pin Voltage VOUT -0.3 VIN + 0.3 Operating Case Temperature Range TO -55 +140 Storage Temperature Range TS -65 +150 Maximmum Junction Temperature TJ - +150 TL RTHJC - +300 1.0 Output Pin Voltage Lead Temperature (Soldering 10sec) Pass Transistor Thermal Resistance, Junction to Case www.irf.com V °C °C/W 1 05/18/12 IRUH330133BK IRUH330133BP Electrical Characteristics c Pre-Radiation @TC = 25°C, VIN = 5.0V (Unless Otherwise Specified) Parameter Output Voltage Test Conditions Symbol 3.8V ≤ V IN ≤ 5.8V, 50mA ≤ IOUT ≤ 3.0A 3.8V ≤ V IN ≤ 5.8V, 50mA ≤ IOUT ≤ 3.0A, c -55°C to +125°C 3.8V ≤ V IN ≤ 5.8V, 50mA ≤ IOUT ≤ 3.0A, c IO = 3.0A, VOUT = 3.3V, -55°C to +125°C, Post -Rad Over-Current Latching, -55°C to +125°C, Current Limit Over-Current Time-to-Latch d Post -Rad IO > ILATCH Maximum Shutdown Temp. d Ripple Rejection VSENSE Pin Current d F= 120Hz, IO = 50mA, -55°C to +125°C F= 120Hz, IO = 50mA, Post -Rad Minimum SHDN Pin "On" -55°C to +125°C ISOURCE = 200µA, -55°C to +125°C Threshold Voltage Maximum SHDN Pin "Off" Post -Rad ISOURCE = 200µA, -55°C to +125°C Threshold Voltage Post -Rad RLOAD = 36 Ohms, VSHDN = 5.0V Output Voltage at Shutdown SHDN Pin Leakage Current d d Power On Reset Threshold d Quiescent Current d SHDN Pin Pull-Up Current -55°C to +125°C, Post-Rad VSHDN = 3.3V, -55°C to +125°C,Post-Rad 3.349 3.201 3.3 3.399 3.184 3.3 3.366 VDROP - - 0.4 V ILATCH 3.5 - - A VOUT tLATCH - 10 - ms 125 65 140 - - °C 40 - - ISENSE - 1.6 - mA VSHDN - - 0.8 V VSHDN 1.2 - - V VOUT -0.1 - 0.1 V ISHDN -10 - 10 µA -98 - -56 -140 -98 - 1.7 -30 -56 µA - 15 V - - 90 PSRR ISHDN VSHDN = 0.4V, Post-Rad Sweep VIN and Measure Output VT-POR Full Load V TLATCH VSHDN = 0.4V VSHDN = 0.4V, -55°C to +125°C No Load Typ. Max. Units 3.3 Post -Rad Dropout Voltage Min. 3.250 IQ dB mA Notes: Connected as shown in Fig.1 and measured at the junction of VOUT and VSENSE Pins. Under normal closed-loop operation. Guaranteed by design. Not tested in production. 2 www.irf.com IRUH330133BK IRUH330133BP Radiation Performance Characteristics Test Conditions Min Typ MIL-STD-883, Method 1019 (Condition A) Total Ionizing Dose (Gamma) Operating Bias applied during exposure Unit 300 500 c Krads (Si) 100 See d Krads (Si) Minimum Rated Load, Vin = 6.4V MIL-STD-883, Method 1019 (Condition D) Total Ionizing Dose (Gamma) (ELDRS) Operating Bias applied during exposure Minimum Rated Load, Vin = 6.4V Single Event effects Heavy Ions (LET) SEU, SEL, SEGR, SEB Operating Bias applied during exposure 2 84 MeV*cm /mg under varying operating conditions Neutron Fluence MIL-STD-883, Method 1017 1.0e 11 2 Neutrons/cm Notes: Tested to 500Krad (Si). See Fig. 5. Space Level Screening Requirements TEST/INSPECTION SCREENING LEVEL MIL-STD-883 SPACE METHOD Nondestructive Bond Pull 100% 2023 Internal Visual 100% 2017 Seal 100% 1014 Temperature Cycle 100% 1010 Constant Acceleration 100% 2001 Mechanical Shock 100% 2002 PIND 100% 2020 Pre Burn-In-Electrical 100% Burn-In 100% Final Electrical 100% Radiographic External Visual 100% 100% www.irf.com 1015 2012 2009 3 IRUH330133BK IRUH330133BP Application Information Input Voltage 0.1uF and 1uF Ceramic; Two 100uF Low ESR Tantalum Output Voltage VOUT VIN IRUH3301xxxx 0.1uF and 1uF Ceramic; Two 100uF Low ESR Tantalum V SENSE SHDN GND Fig. 1. Typical Regulator Circuit; Note the SHDN Pin is hardwired in the “ON” position. The VSENSE Pin is connected as noted in the “General Layout Rules” section. Over-Current & Over-Temperature Protection The IRUH3301 series provides over-current protection by means of a timed latch function. Drive current to the internal PNP pass transistor is limited by an internal resistor (Rb in Fig. 3) between the base of the transistor and the control IC drive FET. If an over-current condition forces the voltage across this resistor to exceed 0.5V (nom), the latch feature will be triggered. The time-tolatch (tLATCH) is nominally 10ms. If the over-current condition exists for less than tLATCH , the latch will not be set. If the latch is set the drive current to the PNP pass transistor will be disabled. The latch will remain set until one of the following actions occur: 1. The SHDN Pin voltage is brought above 1.2V and then lowered below 0.8V. 2. The VIN Pin voltage is lowered below 1.7V. If the junction temperature of the regulator IC exceeds 140°C nominal, the thermal shutdown circuit will set the internal latch and disable the drive current to the PNP pass transistor as described above. After the junction temperature falls below a nominal 125°C, the latch can be reset using either of the actions described above. Under-Voltage Lock-Out The under-voltage lock-out (UVLO) function prevents operation when VIN is less than 1.7V (nominal). There is a nominal 100mV hysteresis about this point. Input Voltage Range The device control functions fully when VIN is greater than 2.8V. The device enters into undervoltage lock-out when VIN < 1.7V (nominal). When 1.7V (nominal) < VIN < 3.7V, VOUT will track VIN and overshoot may occur. A larger output capacitor should be used to slow down the VOUT rise rate for slow VIN ramp applications. Shutdown (SHDN) The regulator can be shutdown by applying a voltage of >1.2V to the SHDN Pin. The regulator will restart when the SHDN Pin is pulled below the shutdown threshold of 0.8V. If the remote shutdown feature is not required, the SHDN Pin should be connected to GND. 4 www.irf.com IRUH330133BK IRUH330133BP Input Capacitance Input bypass capacitors: Two (0.1µF and 1µF) ceramics and two 100µF low ESR tantalums (AVX TPS or equivalent), placed very close to the VIN Pin are required for proper operation. When the input voltage supply capacitance is more than 4 inches from the device, additional input capacitance is recommended. Larger input capacitor values will improve ripple rejection further improving the integrity of the output voltage. Output Capacitance Output bypass capacitors: Two (0.1µF and 1µF) ceramics and two 100µF low ESR tantalums (AVX TPS or equivalent) are required for loop stability. Faster transient performance can be achieved with multiple additional 1µF ceramic capacitors. Ceramic capacitors greater than 1µF in value are not recommended as they can cause stability issues. Tantalum capacitor values larger than the suggested value are recommended to improve the transient response under large load current changes. The upper capacitance value limit is governed by the delayed over-current latch function of the regulator and can be as much as 10,000µF without causing the device to latch-off during start-up. General Layout Rules Low impedance connections between the regulator output and load are essential. Solid power and ground planes are highly recommended. In those cases where the board impedances are not kept very small, oscillations can occur due to the effect of parasitic series resistance and inductance on loop bandwidth and phase margin. The VSENSE Pin must be connected directly to the VOUT Pin using as short a trace as possible with the connection inside the first bypass capacitor (see Fig. 2a). Connect ceramic output capacitors directly across the VOUT and GND Pins with as wide a trace as design rules allow (see Fig. 2a). Avoid the use of vias for these capacitors and avoid loops. Fig.2 shows the ceramic capacitors tied directly to the regulator output. The input capacitors should be connected as close a possible to the VIN Pin. Fig. 2a. Layer 1 conductor. Fig. 2b. Layer 1 silkscreen Ground plane below layer 1 www.irf.com 5 IRUH330133BK IRUH330133BP VSENSE VIN VOUT Input Undervoltage detect SHDN Thermal Shutdown Rb Shutdown & Over Current Latch Disable Error Amp + Latch Timing capacitor VREF GND Fig. 3. Simplified Schematic Circuit Maximum Output Current (A) with no derating at Maximum Dissipation 4.0 Output Current (A) 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 100 110 120 130 140 150 160 170 Mounting Surface Temperature (’C) Fig. 4. Maximum Output Current versus Mounting Surface Temperature with no Derating at Maximum Dissipation 6 www.irf.com IRUH330133BK IRUH330133BP VOut Delta-VOut (%) 0.500% 0.250% ELDRS 0.000% TID -0.250% -0.500% 1 10 100 1000 10000 100000 Total Dose (Rad (Si)) Fig. 5. Change in Output Voltage vs. Total Ionizing Dose Radiation Exposure at Both High and Low Dose Rates PSRR (Typical) 100 90 PSRR (dB) 80 70 60 50 40 30 20 10 0 0.1 1 10 100 1000 Freq (KHz) Recomended Layout and Capcitors, No IRUH Iout=100mA & 1.6A, 3.3Vout, 4.5Vin Fig. 6. Typical Power Supply Ripple Rejection at 100mA and 1.6A using recommended layout and capacitors. Results above 10KHz are influenced by testing setup and layout. www.irf.com 7 IRUH330133BK IRUH330133BP Fig 7. Case Outline and Dimensions - MO-078AA (Lead Form Down) Pin Assignment Pin # Pin Description 1 VIN 2 3 GND VOUT 4 5 SHUTDOWN VSENSE Note: 1) All dimensions are in inches Warning: This Product contains BeO Fig 8. Case Outline and Dimensions - MO-078AA (Lead Form Up) Pin Assignment Pin # Pin Description 1 VIN 2 3 GND VOUT 4 5 SHUTDOWN VSENSE Note: 1) All dimensions are in inches Warning: This Product contains BeO 8 www.irf.com IRUH330133BK IRUH330133BP Fig 9. Case Outline and Dimensions - MO-078AA (Lead Trimmed) Pin Assignment Pin # Pin Description 1 VIN 2 3 GND VOUT 4 5 SHUTDOWN VSENSE Note: 1) All dimensions are in inches Warning: This Product contains BeO Part Numbering Nomenclature IR U H3 301 33 B K Linear Regulator U = Ultra Low Dropout Regulator Radiation Hardening H3 = 300 Krads Device indicator 301 = 3 Amp Positive Regulator Lead Form Options A = Lead Form Down (Fig. 7) B = Lead Form Up (Fig. 8) Blank = Lead Trimmed (Fig. 9) Screening Level P = Unscreened. 25°C Electrical Test Not for Qualification K = Class K per MIL-PRF-38534 Output Voltage 18 = 1.8V 25 = 2.5V 33 = 3.3V A1 = Adjustable Optimized for 3.3 V Input A2 = Adjustable Optimized for 5.0V Input Package Type B = MO-078AA IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 IR LEOMINSTER : 205 Crawford St., Leominster, Massachusetts 01453, USA Tel: (978) 534-5776 TAC Fax: (310) 252-7903 Visit us at www.irf.com for sales contact information. Data and specifications subject to change without notice. 05/2012 www.irf.com 9