Intersil EL5166 1.4ghz current feedback amplifiers with enable Datasheet

EL5166, EL5167
®
Data Sheet
May 15, 2007
1.4GHz Current Feedback Amplifiers with
Enable
The EL5166 and EL5167 amplifiers are of the current
feedback variety and exhibit a very high bandwidth of
1.4GHz at AV = +1 and 800MHz at AV = +2. This makes
these amplifiers ideal for today's high speed video and
monitor applications, as well as a number of RF and IF
frequency designs.
With a supply current of just 8.5mA and the ability to run
from a single supply voltage from 5V to 12V, these amplifiers
offer very high performance for little power consumption.
FN7365.5
Features
• Gain-of-1 bandwidth = 1.4GHz/gain-of-2
bandwidth = 800MHz
• 6000V/µs slew rate
• Single and dual supply operation from 5V to 12V
• Low noise = 1.5nV/√Hz
• 8.5mA supply current
• Fast enable/disable (EL5166 only)
• 600MHz family - (EL5164 and EL5165)
The EL5166 also incorporates an enable and disable
function to reduce the supply current to 13µA typical per
amplifier. Allowing the CE pin to float or applying a low logic
level will enable the amplifier.
• 400MHz family - (EL5162 and EL5163)
The EL5167 is offered in the 5 Ld SOT-23 package and the
EL5166 is available in the 6 Ld SOT-23 as well as the
industry-standard 8 Ld SOIC packages. Both operate over
the industrial temperature range of -40°C to +85°C.
Applications
• 200MHz family - (EL5160 and EL5161)
• Pb-free plus anneal available (RoHS compliant)
• Video amplifiers
• Cable drivers
• RGB amplifiers
• Test equipment
• Instrumentation
• Current to voltage converters
Pinouts
EL5166
(8 LD SOIC)
TOP VIEW
NC 1
IN- 2
IN+ 3
VS- 4
EL5166
(6 LD SOT-23)
TOP VIEW
OUT 1
VS- 2
IN+ 3
1
+ -
8 CE
+
7 VS+
6 OUT
5 NC
EL5167
(5 LD SOT-23, SC-70)
TOP VIEW
6 VS+
OUT 1
5 CE
VS- 2
4 IN-
IN+ 3
5 VS+
+ 4 IN-
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2003-2005, 2007. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
EL5166, EL5167
Ordering Information
PART NUMBER
PART MARKING
TAPE & REEL
PACKAGE
PKG. DWG. #
EL5166IS
5166IS
-
8 Ld SOIC (150 mil)
MDP0027
EL5166IS-T7
5166IS
7”
8 Ld SOIC (150 mil)
MDP0027
EL5166IS-T13
5166IS
13”
8 Ld SOIC (150 mil)
MDP0027
EL5166ISZ (Note)
5166ISZ
-
8 Ld SOIC (150 mil) (Pb-free)
MDP0027
EL5166ISZ-T7 (Note)
5166ISZ
7”
8 Ld SOIC (150 mil) (Pb-free)
MDP0027
EL5166ISZ-T13 (Note)
5166ISZ
13”
8 Ld SOIC (150 mil) (Pb-free)
MDP0027
EL5166IW-T7
h
7” (3k pcs)
6 Ld SOT-23
MDP0038
EL5166IW-T7A
h
7” (250 pcs)
6 Ld SOT-23
MDP0038
EL5166IWZ-T7 (Note)
BAPA
7” (3k pcs)
6 Ld SOT-23 (Pb-free)
MDP0038
EL5166IWZ-T7A (Note)
BAPA
7” (250 pcs)
6 Ld SOT-23 (Pb-free)
MDP0038
EL5167IC-T7
G
7” (3k pcs)
5 Ld SC-70 (1.25mm)
P5.049
EL5167IC-T7A
G
7” (250 pcs)
5 Ld SC-70 (1.25mm)
P5.049
EL5167ICZ-T7 (Note)
BFA
7” (3k pcs)
5 Ld SC-70 (1.25mm) (Pb-free)
P5.049
EL5167ICZ-T7A (Note)
BFA
7” (250 pcs)
5 Ld SC-70 (1.25mm) (Pb-free)
P5.049
EL5167IW-T7
a
7” (3k pcs)
5 Ld SOT-23
MDP0038
EL5167IW-T7A
a
7” (250 pcs)
5 Ld SOT-23
MDP0038
EL5167IWZ-T7 (Note)
BARA
7” (3k pcs)
5 Ld SOT-23 (Pb-free)
MDP0038
EL5167IWZ-T7A (Note)
BARA
7” (250 pcs)
5 Ld SOT-23 (Pb-free)
MDP0038
NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination
finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at
Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
2
FN7365.5
May 15, 2007
EL5166, EL5167
Absolute Maximum Ratings (TA = +25°C)
Thermal Information
Supply Voltage between VS+ and VS- . . . . . . . . . . . . . . . . . . . 12.6V
Slewrate between VS+ and VS- . . . . . . . . . . . . . . . . . . . . . . . . 1V/µs
Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . 50mA
IOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±200mA
I into VIN+, VIN-, Enable Pins . . . . . . . . . . . . . . . . . . . . . . . . . ±4mA
Pin Voltages . . . . . . . . . . . . . . . . . . . . . . . . . VS- -0.5V to VS+ +0.5V
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Die Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . +125°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
Electrical Specifications
VS+ = +5V, VS- = -5V, RF = 392Ω for AV = 1, RF = 250Ω for AV = 2, RL = 150Ω, TA = +25°C
Unless Otherwise Specified.
PARAMETER
DESCRIPTION
CONDITIONS
MIN
TYP
MAX
UNIT
AC PERFORMANCE
BW
-3dB Bandwidth
AV = +1
1400
MHz
AV = +2
800
MHz
100
MHz
6000
V/µs
8
ns
BW1
0.1dB Bandwidth
AV = +2
SR
Slew Rate
VO = -2.5V to +2.5V, AV = +2
tS
0.1% Settling Time
VOUT = -2.5V to +2.5V, AV = -1
eN
Input Voltage Noise
1.7
nV/√Hz
iN-
IN- Input Current Noise
19
pA/√Hz
iN+
IN+ Input Current Noise
50
pA/√Hz
dG
Differential Gain Error (Note 1)
AV = +2
0.01
%
dP
Differential Phase Error (Note 1)
AV = +2
0.03
°
4000
DC PERFORMANCE
VOS
Offset Voltage
TCVOS
Input Offset Voltage Temperature
Coefficient
ROL
Transimpedance
-5
Measured from TMIN to TMAX
-0.5
5
3.52
0.5
1.1
mV
µV/°C
2.5
MΩ
INPUT CHARACTERISTICS
CMIR
Common Mode Input Range
(guaranteed by CMRR test)
±3
±3.3
V
CMRR
Common Mode Rejection Ratio
52
57
66
dB
-ICMR
- Input Current Common Mode Rejection
-1
0.7
1
µA/V
+IIN
+ Input Current
-25
0.7
25
µA
-IIN
- Input Current
-25
8.5
25
µA
RIN
Input Resistance
50
130
250
kΩ
CIN
Input Capacitance
1.5
pF
OUTPUT CHARACTERISTICS
VO
IOUT
Output Voltage Swing
Output Current
3
RL = 150Ω to GND
±3.6
±3.8
±4.1
V
RL = 1kΩ to GND
±3.8
±4.0
±4.2
V
RL = 10Ω to GND
±110
±160
±200
mA
FN7365.5
May 15, 2007
EL5166, EL5167
Electrical Specifications
VS+ = +5V, VS- = -5V, RF = 392Ω for AV = 1, RF = 250Ω for AV = 2, RL = 150Ω, TA = +25°C
Unless Otherwise Specified. (Continued)
PARAMETER
DESCRIPTION
CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY
ISON
Supply Current - Enabled
No load, VIN = 0V
7.5
8.5
9.3
mA
ISOFF+
Supply Current - Disabled
No load, VIN = 0V
1
4
25
µA
ISOFF-
Supply Current - Disabled
No load, VIN = 0V
-25
-14
-1
µA
PSRR
Power Supply Rejection Ratio
DC, VS = ±4.75V to ±5.25V
70
50
-IPSR
- Input Current Power Supply Rejection
DC, VS = ±4.75V to ±5.25V
-0.5
0.2
dB
1
µA/V
ENABLE (EL5166 ONLY)
tEN
Enable Time
170
ns
tDIS
Disable Time
1.25
µs
IIHCE
CE Pin Input High Current
CE = VS+
IILCE
CE Pin Input Low Current
CE = VS-
VIHCE
CE Input High Voltage for Power-down
VILCE
CE Input Low Voltage for Power-down
1
0
-1
µA
13
25
µA
VS+ -1
V
VS+ -3
V
NOTE:
1. Standard NTSC test, AC signal amplitude = 286mV, f = 3.58MHz.
Typical Performance Curves
4
3
4
VCC=5V
VEE=-5V
RL=150Ω
RF=392
2
RF=368
RF=662
1
0
RF=511
-1
RF=608
-2
RF=698
-3
RF=806
-4
-5
100K
RF=900
1M
10M
100M
RF=1K
1G
FREQUENCY (Hz)
FIGURE 1. FREQUENCY RESPONSE AS THE FUNCTION OF
RF
4
NORMALIZED MAGNITUDE (dB)
NORMALIZED MAGNITUDE (dB)
5
3
2
1
RG=392
RG=186
0
-1
-2
RG=93
-3
VCC=5V
-4 VEE=-5V
RL=150Ω
-5
RF=392Ω
-6
100K
1M
RG=43
10M
100M
1G
FREQUENCY (Hz)
FIGURE 2. FREQUENCY RESPONSE AS THE FUNCTION OF
THE GAIN
FN7365.5
May 15, 2007
EL5166, EL5167
Typical Performance Curves (Continued)
5
4
C=4.7p
3
C=2.5p
2
C=1.5p
1
0
-1
C=1p
-2
C=0p
-3
VCC
=+V
V
CC=+5V
=-5V
VEE
V
EE=-5V
RL=150W
R
L=150Ω
RF=RG=392Ω
4
NORMALIZED GAIN (dB)
NORMALIZED MAGNITUDE (dB)
5
3
2
1
C=2.5p
C=1.5p
0
-1
C=1p
-2
-3
C=0
-4
-4
-5
-5
100K
1M
10M
100M
100K
1G
1M
FIGURE 3. FREQENCY RESPONSE vs CIN
4
10M
100M
1G
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 4. NON-INVERTING FREQUENCY RESPONSE FOR
VARIOUS CIN- (6 LD SOT-23)
VCC, VEE=5V
3
2
RF=220
RG=220
1
0
0.5V/DIV
NORMALIZED GAIN (dB)
C=4.7p
-1
RF=220
RG=100
-2
-3
-4
-5
-6
1M
100M
10M
1G
2ns/DIV
FREQUENCY (Hz)
FIGURE 6. RISE AND FALL TIME (6 LD SOT-23)
FIGURE 5. INVERTING FREQUENCY RESPONSE FOR GAIN
OF 1 AND 2
4
2
4
RL=150Ω
RF=300Ω
RG=300Ω
3
5.0V
1
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
3
6.0V
0
-1
-2
2.5V
3.0V
-3
-4
2
0
-1
-4
-5
10M
100M
1G
FIGURE 7. FREQUENCY RESPONSE AS THE FUNCTION OF
THE POWER SUPPLY VOLTAGE
5
5.0V
-3
-6
1M
FREQUENCY (Hz)
6.0V
-2
-6
1M
2.5V
3.5V
1
-5
100K
RL=150Ω
RF=220Ω
RG=220Ω
10M
100M
1K
FREQUENCY (Hz)
FIGURE 8. INVERTING AMPLIFIER, FREQUENCY
RESPONSE AS THE FUNCTION OF VCC, VEE
GAIN - 1
FN7365.5
May 15, 2007
EL5166, EL5167
Typical Performance Curves (Continued)
2.5V
VCC, VEE=2.5V
5.0V
MAGNITUDE (dB)
6.0V
VCC, VEE=5V
GAIN=2
10
0
2.5V 5.0V
-180
PHASE (°)
-90
10K
ZOUT (Ω)
100K
1
100m
1K
-270
100
10m
100K
10M
1M
10K
1G
100M
FREQUENCY (Hz)
FIGURE 9. TRANSIMPEDANCE MAGNITUDE AND PHASE AS
THE FUNCTION OF THE FREQUENCY
FIGURE 10. CLOSED LOOP OUTPUT IMPEDANCE vs
FREQUENCY (6 LD SOT-23)
0
0
10
20
PSRR (VEE) (dB)
PSRR (VCC) (dB)
VCC=5V
10 VEE=-5V
RL=150Ω
20 RF=402Ω
RG=402Ω
30
40
50
60
50
60
70
80
10K
1K
100K
1M
10M
VCC=5V
VEE=-5V
RL=150Ω
RF=402Ω
RG=402Ω
40
70
100
100M
1K
10K
100K
1M
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 11. PSRR +5V
FIGURE 12. PSRR -5V
10M
100M
3
NORMALIZED MAGNITUDE (dB)
0
RF=RG=250Ω
-20
CMRR (dB)
30
80
100
-10
100M
10M
1M
100K
FREQUENCY (Hz)
-30
-40
2.5V
-50
6.0V
5.0V
-60
-70
3.5V
2
1
0
-1
-2
-3
-4
-5
-6
-7
-80
1K
10K
100K
1M
10M
100M 300M
FREQUENCY (Hz)
FIGURE 13. COMMON MODE REJECTION AS THE FUNCTION
OF THE FREQUENCY AND POWER SUPPLY
VOLTAGE
6
VCC=5V
VEE=-5V
RL=150Ω
GAIN=2
LOAD=150Ω
INPUT LEVEL=3VP-P
100K
1M
10M
100M
1G
FREQUENCY (Hz)
FIGURE 14. LARGE SIGNAL RESPONSE
FN7365.5
May 15, 2007
EL5166, EL5167
Typical Performance Curves (Continued)
-50
2
VCC, VEE =
VCC, VEE=5V,
RL=150Ω, AV=2
-55
±6V
DISTORTION (dB)
VOUTP-P (V)
1.5
±5V
±3V
1
±2.5V
-60
THD
-65
-70
SECOND
HARMONIC
-75
THIRD
HARMONIC
0.5
-80
-85
0
100 200 300 400 500 600 700 800 900 1000
1
6
11
FIGURE 15. TOUT vs FREQUENCY AND VCC, VEE
31
26
36
FIGURE 16. DISTORTION vs FREQUENCY
10
-74
f=1MHz, RL=150Ω,
AV=2, VOP-P=2V
-76
f=5MHz, RL=150Ω,
AV=2, VO=2VP-P
0
-10
DISTORTION (dB)
DISTORTION (dB)
21
FREQUENCY (MHz)
FREQUENCY (Hz)
THD
-78
HD2
-80
HD3
-82
-20
-30
-40
-50
THD
-60
HD2
-70
-84
-80
HD3
-90
-86
5
6
7
9
8
11
10
5
12
6
7
9
8
10
11
12
TOTAL SUPPLY VOLTAGE (V)
TOTAL SUPPLY VOLTAGE (V)
FIGURE 17. HARMONIC DISTORTION vs SUPPLY VOLTAGE
FIGURE 18. HARMONIC DISTORTION vs SUPPLY VOLTAGE
-50
-50
f=10MHz,
RL=150Ω,
AV=2
VO=2VP-P
-60
-65
THD
-70
SECOND
HARMONIC
-75
THIRD
HARMONIC
-80
f=20MHz,
RL=150Ω,
AV=2
VO=2VP-P
-55
DISTORTION (dB)
-55
DISTORTION (dB)
16
-60
-65
THD
-70
SECOND
HARMONIC
THIRD
HARMONIC
-75
-85
-80
-90
5
6
7
8
9
10
11
12
TOTAL SUPPLY VOLTAGE (V)
FIGURE 19. DISTORTION vs POWER SUPPLY VOLTAGE
7
5
6
7
8
9
10
11
12
TOTAL SUPPLY VOLTAGE (V)
FIGURE 20. DISTORTION vs POWER SUPPLY VOLTAGE (EL5166)
FN7365.5
May 15, 2007
EL5166, EL5167
Typical Performance Curves (Continued)
FIGURE 21. TURN ON TIME (EL5166)
FIGURE 22. TURN OFF TIME (EL5166)
JEDEC JESD51-7 HIGH EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
8.5
1.4
8.3
8.2
POWER DISSIPATION (W)
SUPPLY CURRENT (mA)
8.4
IS
8.1
8
7.9
IS-
7.8
7.7
7.6
7.5
7.4
2.5
3
3.5
4
4.5
5
5.5
1.2
1
909mW
SO8
θJA=110°C/W
0.8
0.6
435mW
0.4
SOT23-5/6
θJA=230°C/W
0.2
0
6
0
25
SUPPLY VOLTAGE (V)
50
75 85 100
125
150
AMBIENT TEMPERATURE (°C)
FIGURE 23. SUPPLY CURRENT vs SUPPLY VOLTAGE (EL5166)
FIGURE 24. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
JEDEC JESD51-3 LOW EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
1
POWER DISSIPATION (W)
0.9
0.8
0.7 625mW
0.6
0.5
SO8
θJA=160°C/W
391mW
0.4
0.3
SOT23-5/6
θJA=256°C/W
0.2
0.1
0
0
25
50
75 85 100
125
150
AMBIENT TEMPERATURE (°C)
FIGURE 25. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE
8
FN7365.5
May 15, 2007
EL5166, EL5167
Pin Descriptions
8 LD SOIC
6 LD SOT-23
5 LD SOT-23
1, 5
2
4
4
PIN
NAME
FUNCTION
NC
Not connected
IN-
Inverting input
EQUIVALENT CIRCUIT
VS+
IN+
IN-
VSCIRCUIT 1
3
3
3
IN+
Non-inverting input
4
2
2
VS-
Negative supply
6
1
1
OUT
Output
(See circuit 1)
VS+
OUT
VSCIRCUIT 2
7
6
8
5
5
VS+
Positive supply
CE
Chip enable
VS+
CE
VSCIRCUIT 3
9
FN7365.5
May 15, 2007
EL5166, EL5167
Applications Information
Product Description
The EL5166 and EL5167 are current-feedback operational
amplifiers that offers a wide -3dB bandwidth of 1.4GHz and a
low supply current of 8.5mA per amplifier. The EL5166 and
EL5167 work with supply voltages ranging from a single 5V
to 10V and they are also capable of swinging to within 1V of
either supply on the output. Because of their currentfeedback topology, the EL5166 and EL5167 do not have the
normal gain-bandwidth product associated with voltagefeedback operational amplifiers. Instead, their -3dB
bandwidth remains relatively constant as closed-loop gain is
increased. This combination of high bandwidth and low
power, together with aggressive pricing make the EL5166
and EL5167 ideal choices for many low-power/highbandwidth applications such as portable, handheld, or
battery-powered equipment.
Power Supply Bypassing and Printed Circuit
Board Layout
As with any high frequency device, good printed circuit
board layout is necessary for optimum performance. Low
impedance ground plane construction is essential. Surface
mount components are recommended, but if leaded
components are used, lead lengths should be as short as
possible. The power supply pins must be well bypassed to
reduce the risk of oscillation. The combination of a 4.7µF
tantalum capacitor in parallel with a 0.01µF capacitor has
been shown to work well when placed at each supply pin.
For good AC performance, parasitic capacitance should be
kept to a minimum, especially at the inverting input. (See the
Capacitance at the Inverting Input section) Even when
ground plane construction is used, it should be removed
from the area near the inverting input to minimize any stray
capacitance at that node. Carbon or Metal-Film resistors are
acceptable with the Metal-Film resistors giving slightly less
peaking and bandwidth because of additional series
inductance. Use of sockets, particularly for the SO package,
should be avoided if possible. Sockets add parasitic
inductance and capacitance which will result in additional
peaking and overshoot.
Disable/Power-Down
The EL5166 amplifier can be disabled placing its output in a
high impedance state. When disabled, the amplifier supply
current is reduced to 13µA. The EL5166 is disabled when its
CE pin is pulled up to within 1V of the positive supply.
Similarly, the amplifier is enabled by floating or pulling its CE
pin to at least 3V below the positive supply. For ±5V supply,
this means that an EL5166 amplifier will be enabled when
CE is 2V or less, and disabled when CE is above 4V.
Although the logic levels are not standard TTL, this choice of
logic voltages allows the EL5166 to be enabled by tying CE
to ground, even in 5V single supply applications. The CE pin
can be driven from CMOS outputs.
10
Capacitance at the Inverting Input
Any manufacturer’s high-speed voltage- or current-feedback
amplifier can be affected by stray capacitance at the
inverting input. For inverting gains, this parasitic capacitance
has little effect because the inverting input is a virtual
ground. But for non-inverting gains, this capacitance (in
conjunction with the feedback and gain resistors) creates a
pole in the feedback path of the amplifier. This pole, if low
enough in frequency, has the same destabilizing effect as a
zero in the forward open-loop response. The use of large
value feedback and gain resistors exacerbates the problem
by further lowering the pole frequency (increasing the
possibility of oscillation).
The EL5166 and EL5167 frequency responses are
optimized with the resistor values in Figure 3. With the high
bandwidth of these amplifiers, these resistor values might
cause stability problems when combined with parasitic
capacitance, thus ground plane is not recommended around
the inverting input pin of the amplifier.
Feedback Resistor Values
The EL5166 and EL5167 have been designed and specified
at a gain of +2 with RF approximately 392Ω. This value of
feedback resistor gives 800MHz of -3dB bandwidth at AV = 2
with about 0.5dB of peaking. Since the EL5166 and EL5167
are current-feedback amplifiers, it is also possible to change
the value of RF to get more bandwidth. As seen in the curve
of Frequency Response for Various RF and RG, bandwidth
and peaking can be easily modified by varying the value of
the feedback resistor.
Because the EL5166 and EL5167 are current-feedback
amplifiers, their gain-bandwidth product is not a constant for
different closed-loop gains. This feature actually allows the
EL5166 and EL5167 to maintain reasonable constant -3dB
bandwidth for different gains. As gain is increased,
bandwidth decreases slightly while stability increases. Since
the loop stability is improving with higher closed-loop gains,
it becomes possible to reduce the value of RF below the
specified 250Ω and still retain stability, resulting in only a
slight loss of bandwidth with increased closed-loop gain.
Supply Voltage Range and Single-Supply
Operation
The EL5166 and EL5167 have been designed to operate
with supply voltages having a span of greater than 5V and
less than 10V. In practical terms, this means that the EL5166
and EL5167 will operate on dual supplies ranging from
±2.5V to ±5V. With single-supply, they will operate from 5V to
10V.
As supply voltages continue to decrease, it becomes
necessary to provide input and output voltage ranges that
can get as close as possible to the supply voltages. The
EL5166 and EL5167 have an input range which extends to
within 1.8V of either supply. So, for example, on ±5V
supplies, the EL5166 and EL5167 have an input range
FN7365.5
May 15, 2007
EL5166, EL5167
which spans ±3.2V. The output range of the EL5166 and
EL5167 is also quite large, extending to within 1V of the
supply rail. On a ±5V supply, the output is therefore capable
of swinging from -4V to +4V.
Video Performance
For good video performance, an amplifier is required to
maintain the same output impedance and the same
frequency response as DC levels are changed at the
output. This is especially difficult when driving a standard
video load of 150Ω, because of the change in output
current with DC level. Previously, good differential gain
could only be achieved by running high idle currents
through the output transistors (to reduce variations in
output impedance.) These currents were typically
comparable to the entire 8.5mA supply current of each
EL5166 and EL5167 amplifier. Special circuitry has been
incorporated in the EL5166 and EL5167 to reduce the
variation of output impedance with current output. This
results in dG and dP specifications of 0.01% and 0.03°,
while driving 150Ω at a gain of 2.
Output Drive Capability
about 25Ω, it is important to calculate the maximum junction
temperature (TJMAX) for the application to determine if
power supply voltages, load conditions, or package type
need to be modified for the EL5166 and EL5167 to remain in
the safe operating area. These parameters are calculated as
follows:
T JMAX = T MAX + ( θ JA × n × PD MAX )
where:
TMAX = Maximum ambient temperature
θJA = Thermal resistance of the package
n = Number of amplifiers in the package
PDMAX = Maximum power dissipation of each amplifier in
the package
PDMAX for each amplifier can be calculated as follows:
V OUTMAX
PD MAX = ( 2 × V S × I SMAX ) + ( V S – V OUTMAX ) × ---------------------------R
L
where:
In spite of their low 8.5mA of supply current, the EL5166 and
EL5167 are capable of providing a minimum of ±110mA of
output current. With so much output drive, the EL5166 and
EL5167 are capable of driving 50Ω loads to both rails,
making them an excellent choice for driving isolation
transformers in telecommunications applications.
VS = Supply voltage
ISMAX = Maximum supply current of 1A
VOUTMAX = Maximum output voltage (required)
RL = Load resistance
Driving Cables and Capacitive Loads
When used as a cable driver, double termination is always
recommended for reflection-free performance. For those
applications, the back-termination series resistor will
decouple the EL5166 and EL5167 from the cable and allow
extensive capacitive drive. However, other applications may
have high capacitive loads without a back-termination
resistor. In these applications, a small series resistor (usually
between 5Ω and 50Ω) can be placed in series with the
output to eliminate most peaking. The gain resistor (RG) can
then be chosen to make up for any gain loss which may be
created by this additional resistor at the output. In many
cases it is also possible to simply increase the value of the
feedback resistor (RF) to reduce the peaking.
Current Limiting
The EL5166 and EL5167 have no internal current-limiting
circuitry. If the output is shorted, it is possible to exceed the
Absolute Maximum Rating for output current or power
dissipation, potentially resulting in the destruction of the
device.
Power Dissipation
With the high output drive capability of the EL5166 and
EL5167, it is possible to exceed the 125°C Absolute
Maximum junction temperature under certain very high load
current conditions. Generally speaking when RL falls below
11
FN7365.5
May 15, 2007
EL5166, EL5167
Typical Application Circuits
0.1µF
+5V
250Ω
IN+
IN-
VS+
EL5166
250Ω
0.1µF
OUT
+5V
VS0.1µF
IN+
VS+
-5V
250Ω
IN-
VS+
EL5166
250Ω
-5V
250Ω
+5V
0.1µF
5Ω
OUT
IN+
VIN
VS0.1µF
VS+
EL5166
IN-
OUT
VOUT
VS0.1µF
-5V
250Ω
OUT
VS0.1µF
VOUT
+5V
IN+
IN-
5Ω
0.1µF
EL5166
250Ω
-5V
VIN
FIGURE 26. INVERTING 200mA OUTPUT CURRENT
DISTRIBUTION AMPLIFIER
FIGURE 27. FAST-SETTLING PRECISION AMPLIFIER
0.1µF
0.1µF
+5V
+5V
IN+
VS+
EL5166
IN-
IN+
OUT
IN-
VS+
EL5166
VS0.1µF
OUT
VS0.1µF
-5V
-5V
250Ω
0.1µF
120Ω
250Ω
250Ω
VOUT+
0.1µF
1kΩ
0.1µF
240Ω
+5V
+5V
IN+
VS+
EL5166
IN-
OUT
VS0.1µF
0.1µF
120Ω
IN+
VOUT1kΩ
IN-
VS+
EL5166
-5V
250Ω
VIN
VOUT
VS0.1µF
-5V
250Ω
OUT
250Ω
TRANSMITTER
250Ω
RECEIVER
FIGURE 28. DIFFERENTIAL LINE DRIVER/RECEIVER
12
FN7365.5
May 15, 2007
EL5166, EL5167
Small Outline Package Family (SO)
A
D
h X 45°
(N/2)+1
N
A
PIN #1
I.D. MARK
E1
E
c
SEE DETAIL “X”
1
(N/2)
B
L1
0.010 M C A B
e
H
C
A2
GAUGE
PLANE
SEATING
PLANE
A1
0.004 C
0.010 M C A B
L
b
0.010
4° ±4°
DETAIL X
MDP0027
SMALL OUTLINE PACKAGE FAMILY (SO)
INCHES
SYMBOL
SO-14
SO16 (0.300”)
(SOL-16)
SO20
(SOL-20)
SO24
(SOL-24)
SO28
(SOL-28)
TOLERANCE
NOTES
A
0.068
0.068
0.068
0.104
0.104
0.104
0.104
MAX
-
A1
0.006
0.006
0.006
0.007
0.007
0.007
0.007
±0.003
-
A2
0.057
0.057
0.057
0.092
0.092
0.092
0.092
±0.002
-
b
0.017
0.017
0.017
0.017
0.017
0.017
0.017
±0.003
-
c
0.009
0.009
0.009
0.011
0.011
0.011
0.011
±0.001
-
D
0.193
0.341
0.390
0.406
0.504
0.606
0.704
±0.004
1, 3
E
0.236
0.236
0.236
0.406
0.406
0.406
0.406
±0.008
-
E1
0.154
0.154
0.154
0.295
0.295
0.295
0.295
±0.004
2, 3
e
0.050
0.050
0.050
0.050
0.050
0.050
0.050
Basic
-
L
0.025
0.025
0.025
0.030
0.030
0.030
0.030
±0.009
-
L1
0.041
0.041
0.041
0.056
0.056
0.056
0.056
Basic
-
h
0.013
0.013
0.013
0.020
0.020
0.020
0.020
Reference
-
16
20
24
28
Reference
-
N
SO-8
SO16
(0.150”)
8
14
16
Rev. M 2/07
NOTES:
1. Plastic or metal protrusions of 0.006” maximum per side are not included.
2. Plastic interlead protrusions of 0.010” maximum per side are not included.
3. Dimensions “D” and “E1” are measured at Datum Plane “H”.
4. Dimensioning and tolerancing per ASME Y14.5M-1994
13
FN7365.5
May 15, 2007
EL5166, EL5167
SOT-23 Package Family
MDP0038
e1
D
SOT-23 PACKAGE FAMILY
A
MILLIMETERS
6
N
SYMBOL
4
E1
2
E
3
0.15 C D
1
2X
2
3
0.20 C
5
2X
e
0.20 M C A-B D
B
b
NX
0.15 C A-B
1
3
SOT23-5
SOT23-6
A
1.45
1.45
MAX
A1
0.10
0.10
±0.05
A2
1.14
1.14
±0.15
b
0.40
0.40
±0.05
c
0.14
0.14
±0.06
D
2.90
2.90
Basic
E
2.80
2.80
Basic
E1
1.60
1.60
Basic
e
0.95
0.95
Basic
e1
1.90
1.90
Basic
L
0.45
0.45
±0.10
L1
0.60
0.60
Reference
N
5
6
Reference
D
2X
TOLERANCE
Rev. F 2/07
NOTES:
C
A2
2. Plastic interlead protrusions of 0.25mm maximum per side are not
included.
SEATING
PLANE
A1
0.10 C
1. Plastic or metal protrusions of 0.25mm maximum per side are not
included.
3. This dimension is measured at Datum Plane “H”.
4. Dimensioning and tolerancing per ASME Y14.5M-1994.
NX
5. Index area - Pin #1 I.D. will be located within the indicated zone
(SOT23-6 only).
(L1)
6. SOT23-5 version has no center lead (shown as a dashed line).
H
A
GAUGE
PLANE
c
L
14
0.25
0° +3°
-0°
FN7365.5
May 15, 2007
EL5166, EL5167
Small Outline Transistor Plastic Packages (SC70-5)
P5.049
D
VIEW C
e1
5 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE
INCHES
5
SYMBOL
4
E
CL
1
2
CL
3
e
E1
b
CL
0.20 (0.008) M
C
C
CL
A
A2
SEATING
PLANE
A1
-C-
WITH
PLATING
b1
NOTES
0.031
0.043
0.80
1.10
-
0.004
0.00
0.10
-
A2
0.031
0.039
0.80
1.00
-
b
0.006
0.012
0.15
0.30
-
b1
0.006
0.010
0.15
0.25
c
0.003
0.009
0.08
0.22
6
c1
0.003
0.009
0.08
0.20
6
D
0.073
0.085
1.85
2.15
3
E
0.071
0.094
1.80
2.40
-
E1
0.045
0.053
1.15
1.35
3
e
0.0256 Ref
0.65 Ref
-
e1
0.0512 Ref
1.30 Ref
-
L2
0.010
0.018
0.017 Ref.
0.26
0.46
4
0.420 Ref.
0.006 BSC
0o
N
c1
MAX
0.000
α
c
MIN
A
L
b
MILLIMETERS
MAX
A1
L1
0.10 (0.004) C
MIN
-
0.15 BSC
8o
0o
5
8o
-
5
5
R
0.004
-
0.10
-
R1
0.004
0.010
0.15
0.25
Rev. 2 9/03
NOTES:
BASE METAL
1. Dimensioning and tolerances per ASME Y14.5M-1994.
2. Package conforms to EIAJ SC70 and JEDEC MO-203AA.
4X θ1
3. Dimensions D and E1 are exclusive of mold flash, protrusions,
or gate burrs.
R1
4. Footlength L measured at reference to gauge plane.
5. “N” is the number of terminal positions.
R
GAUGE PLANE
SEATING
PLANE
L
C
L1
α
L2
6. These Dimensions apply to the flat section of the lead between
0.08mm and 0.15mm from the lead tip.
7. Controlling dimension: MILLIMETER. Converted inch dimensions are for reference only.
4X θ1
VIEW C
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
15
FN7365.5
May 15, 2007