FEATURES • • • • • • • • • • –55° to +125°C operation 16 to 40 VDC input Fully Isolated Optocoupler feedback Fixed frequency 550 kHz typical Topology – Single Ended Flyback 50 V for up to 50 ms transient protection Inhibit function Indefinite short circuit protection Up to 74% efficiency DC/DC CONVERTERS 28 VOLT INPUT MGA SERIES 5 WATT MODELS VDC OUTPUT SINGLE 5 12 15 DUAL ±5 ±12 ±15 Size (max.): 1.110 x 1.110 x 0.250 inches (28.19 x 28.19 x 6.35 mm) Shown with “Gull Wing” lead option, also available with straight leads. See Section B8, case D, for dimensions and options. Weight: 15 grams maximum. Screening: Standard, ES, or 883 (Class H). See Section B9 for screening options, see Section A5 for ordering information. DESCRIPTION The MGA Series™ of DC/DC converters delivers 5 watts of output power from a wide input voltage range of 16 to 40 VDC with up to 74% efficiency. Output models of 5, 12, 15, ±5, ±12 and ±15 VDC meet a variety of system needs. All units withstand transients of up to 50 V for up to 50 milliseconds and operate over the full military temperature range of -55°C to +125°C. a TTL low voltage (0.8 V or less) to the inhibit terminal (pin 1) disables the output. Leaving the inhibit terminal unconnected or connecting the inhibit terminal to an open collector gate enables the output. The inhibit terminal has an open circuit voltage of 9 to 11 V. In the inhibit mode the inhibit pin will source a maximum of 4 mA. See “Inhibit Interface,” Figure 2. CONVERTER DESIGN MIL-STD-461 The MGA converters incorporate flyback topology with a typical constant switching frequency of 500 kHz. Isolation between input and output circuits is provided with a transformer in the forward path and a temperature compensated optical link in the feedback control loop. The feed-forward compensation design delivers an audio rejection of 50 dB, typical, with input ripple as low as 50 mA p-p and output ripple as low as 100 mV p-p. Output filter examples in Figures 3 and 4 provide suggested solutions for systems where very low output ripple is required. Tightly coupled magnetics minimize cross regulation in the MGA dual output models. Either output can provide up to 80% of the total available output power, providing the opposite output is carrying at least 20% of the total output power. The converter’s short circuit current protection restricts the output current to approximately 115% of the full load output current. Use Interpoint’s FMGA-461 EMI filter to pass the CE03 requirements of MIL-STD-461C. SURFACE MOUNT PACKAGE The MGA DC/DC converters can be surface mounted with pick-andplace equipment or manually. It is recommended that the case be attached with flexible epoxy adhesive or silicone which is thermally conductive (>1 watt /meter/°K). Internal components are soldered with SN96 (melting temperature 221°C) to prevent damage during reflow. Maximum reflow temperature for surface mounting the MGA converter is 220°C for a maximum of 30 seconds. SN60, 62, or 63 are the recommended types of solder. Hand soldering should not exceed 300°C for 10 seconds per pin. The hermetically sealed metal cases are available in two different lead configurations. See Section B8, cases D1 and D2. INHIBIT FUNCTION The MGA converter’s inhibit terminal disables internal switching, resulting in no output and very low quiescent input current. Applying B2-81 MGA SERIES 5 WATT DC/DC CONVERTERS ABSOLUTE MAXIMUM RATINGS TYPICAL CHARACTERISTICS INHIBIT Input Voltage • 16 to 40 V Output Power • 5 watts Lead Soldering Temperature • Reflow 220°C 30 sec. max SN60, 62 or 63 recommended solder • Hand solder 300°C 10 sec. max. per lead Storage Temperature Range (Case) • –65°C to +150°C Inhibit: TTL Open Collector • Logic low (output disabled) Logic low voltage ≤0.8 V • Referenced to input common • Logic high (output enabled) Open collector Output Voltage Temperature Coefficient • 100 ppm/°C typ, 150 ppm/C max Current Limit • 115% of full load typical Isolation • Input to output • Any pin to case except case pins • 100 megohm minimum at 500 V Conversion Frequency • 500 kHz typical 450 kHz. min, 600 kHz max Inhibit Pin Voltage (unit enabled) • 9 to 11 V RECOMMENDED OPERATING CONDITIONS Input Voltage Range • 16 to 40 VDC continuous • 50 V for up to 50 msec transient Case Operating Temperature (Tc) • –55°C to +125°C full power • –55°C to +135°C absolute Derating Output Power/Current (Tc) • Linearly from 100% at 125°C to 0% at 135°C Electrical Characteristics: 25°C Tc, 28 VDC Vin, 100% load, unless otherwise specified. SINGLE OUTPUT MODELS PARAMETER MGA2805S MGA2812S MGA2815S CONDITIONS MIN TYP MAX MIN TYP OUTPUT VOLTAGE +VOUT 4.95 5.0 5.05 11.88 12 OUTPUT CURRENT VIN = 16 to 40 VDC 0 — 1000 0 — 417 OUTPUT POWER VIN = 16 to 40 VDC — — 5 — — OUTPUT RIPPLE 10 kHz - 2 MHz — 250 450 — LINE REGULATION VIN = 16 to 40 VDC — 10 50 LOAD REGULATION NO LOAD TO FULL — 10 50 CONTINUOUS 16 28 40 INPUT VOLTAGE NO LOAD TO FULL INPUT CURRENT INPUT RIPPLE 10 kHz - 10 MHz STEP LOAD RESPONSE2 STEP LINE RESPONSE4 START-UP MIN TYP MAX UNITS 15 15.15 VDC 0 — 333 mA 5 — — 5 W 100 500 — 100 600 mV p-p — 10 50 — 10 50 mV — 10 50 — 10 50 mV 16 28 40 16 28 40 VDC V 12.12 14.85 TRANSIENT 50 ms — — 50 — — 50 — — 50 NO LOAD — 27 60 — 29 60 — 31 60 FULL LOAD — — 279 — — 263 — — 259 INHIBITED — 3 4 — 3 4 — 3 4 Tc = 25°C — 50 200 — 50 200 — 50 200 Tc = –55°C to +125°C — 75 300 — 75 300 — 75 300 64 69 — 68 74 — 69 74 — POWER DISS. — 1.5 2.0 — 1.2 1.9 — 1.2 1.8 W RECOVERY — 10 75 — 10 30 — 10 30 ms EFFICIENCY LOAD FAULT1 MAX mA mA p-p % SHORT CIRCUIT 50% – 100% – 50% LOAD TRANSIENT –500 200 500 –750 300 750 –1000 400 1000 mV pk RECOVERY3 — 200 500 — 400 1000 — 400 1000 µs mV pk 16 – 40 – 16 VDC TRANSIENT –500 100 500 –800 200 800 –500 100 500 RECOVERY3 — .4 1.0 — 0.5 1.3 — 0.5 1.3 ms OVERSHOOT 0 0 200 0 0 500 0 0 500 mV pk DELAY 0 10 75 0 10 30 0 10 30 ms INHIBITED — 2.5 4.0 — 2.5 4.0 — 2.5 4.0 mA INPUT TO OUTPUT — 50 — — 40 — — 60 — pF — — 300 — — 500 — — 500 µF INHIBIT PIN CURRENT CAPACITANCE CAPACITIVE LOAD Notes 1. Indefinite short circuit protection not guaranteed above 125°C (case). 2. Load transient transition time is >10 µs. B2-82 3. Recovery time is measured from application of the transient to the point at which Vout is within regulation. 4. Input step transition time is >10µs. MGA SERIES 5 WATT DC/DC CONVERTERS Electrical Characteristics: 25°C Tc, 28 VDC Vin, 100% load, unless otherwise specified. DUAL OUTPUT MODELS MGA2805D MGA2812D MGA2815D PARAMETER CONDITIONS MIN TYP MAX OUTPUT VOLTAGE +VOUT 11.88 –VOUT –11.76 –12 –12.24 12 12.12 14.85 TYP MAX 15 15.15 UNITS VDC –14.70 –15 –15.30 OUTPUT CURRENT VIN = 16 to 40 VDC 0 0 ±167 267 OUTPUT POWER 1 VIN = 16 to 40 VDC — — 5 — — 5 W OUTPUT RIPPLE 2 10 kHz - 2 MHz — 120 300 — 120 300 mV p-p LINE REGULATION +VOUT — 10 50 — 10 50 VIN = 16 to 40 VDC –VOUT — 40 180 — 40 180 LOAD REGULATION +VOUT (BALANCED) — 10 50 — 10 50 NO LOAD TO FULL –VOUT (BALANCED) — 50 200 — 50 200 CROSS REG.3 EFFECT ON –VOUT — 8 15 — 7 15= % CONTINUOUS 16 28 40 16 28 40 VDC V INPUT VOLTAGE NO LOAD TO FULL ±208 333 MIN mA mV mV TRANSIENT 50 ms — — 50 — — 50 NO LOAD — 33 63 — 38 63 — — 267 — — 263 — 3 4 — 3 4 — 50 200 — 50 200 — 75 300 — 75 300 67 73 — 68 73 — POWER DISS. — 1.3 1.7 — 1.3 1.6 W RECOVERY — 10 30 — 10 30 ms STEP LOAD TRANSIENT –550 180 550 –600 180 600 mV pk RESP O N S E 5, 6 RECOVERY 7 — 200 500 — 200 500 µs –1500 200 1500 mV pk INPUT CURRENT FULL LOAD INHIBITED INPUT RIPPLE 10 kHz - 10 MHz Tc = 25°C Tc = –55°C to +125°C TION EFFICIENCY LOAD FAULT4 STEP LINE RESP O N S E 8 START-UP AVAILABLE SOON, ASK YOUR INTERPOINT REP FOR INFORMA- mA mA p-p % SHORT CIRCUIT 16 – 40 – 16 VDC TRANSIENT –500 100 500 RECOVERY 7 — 0.8 2.0 — 1.6 4.0 ms OVERSHOOT 0 200 500 0 200 500 mV pk DELAY 0 10 30 0 10 30 ms UNIT INHIBITED — 2.5 4.0 — 2.5 4.0 mA INPUT TO OUTPUT — 50 — — 50 — pF — — 100 — — 100 µF INHIBIT PIN CURRENT CAPACITANCE CAPACITIVE LOAD Notes 1. Up to 4 watts, 80% of the total output power is available from either output providing the opposite output is simultaneously carrying 20% of the total output power. Each output must carry a minimum of 20% of the total output power in order to maintain regulation on the negative output. 2. Applies to both +Vout and –Vout 3. Cross regulation is specified for the following percentages of total output power: +PO = 20% and –PO = 80% to +PO =80% and –PO = 20% 4. Indefinite short circuit protection not guaranteed above 125°C (case). 5. Load transient transition time is >10 µs. 6. Response of either output when the load for each output is simultaneously transitioned from 25% to 50% to 25% of total output power (5 watts). 7. Recovery time is measured from application of the transient to the point at which Vout is within regulation. 8. Input step transition time is >10µs. B2-83 MGA SERIES 5 WATT DC/DC CONVERTERS DIAGRAMS AND CONNECTIONS Positive Input Positive Output + Inhibit Error Amp VR PWM Control + Input Common Negative Output Isolated Feedback Case Ground Output Common = Dual Output FIGURE 1: BLOCK DIAGRAM MGA Positive Input 12 k 5k Inhibit FIGURE 2: INHIBIT INTERFACE 400 50 k 200 pF 2N3904 10V 10 K Vcc 10 k 3.9 K Input Common EMI Filter From input power source Positive Input Input Common MGA2815S T1 Positive Output Positive Positive Input Output Case Output Common Input Output Common Common C2 + C3 To Load Case T1 C1 FIGURE 3: LOW NOISE OUTPUT FILTER MGA SINGLE OUTPUT MODEL EMI Filter From input power source MGA2815D T1 Positive Input Positive Positive Positive Input Output Output Case Output Common Input Output Input Negative Common Common Common Output C2 C4 Case C1 + C 3 + C To Loads 5 T2 FIGURE 4: LOW NOISE OUTPUT FILTER MGA DUAL OUTPUT MODEL B2-84 The filter suggestions in Figures 3 and 4 will further reduce the output ripple for systems requiring very low output noise. C1 = 0.27 µF ceramic capacitor, 500V C2 = C4 = 6.8 µF tantalum capacitor C3 = C5 = 0.27 µF ceramic capacitor Single output: T1 = 15T #28 AWG winding on toroid, m = 5000 Dual output: T2 = 10T #28 AWG winding on toroid, m = 5000 MGA SERIES 5 WATT DC/DC CONVERTERS Pin 1 2, 3 4 5, 6 7, 8 9, 10 11, 12 13 14 15, 16 17, 18 19, 20 Single Output Inhibit Positive Input No connection Input Common Case Ground No connection Positive Output Positive Output Output Common Output Common No connection Case Ground PIN OUT Dual Output Inhibit Positive Input No connection Input Common Case Ground No connection Positive Output Output Common Output Common Negative Output No connection Case Ground 1 2 3 4 5 6 7 8 9 10 TOP VIEW MGA Differently colored glass bead around pin one or dimple in header (bottom of case) indicates pin one. Cover marking is oriented with pin one at the upper right corner. See Section B8, case D for dimensions and gull-wing lead option. To meet specified performance, all pins must be connected except “No Connection” pins. FIGURE 5: PIN OUT SMD NUMBERS STANDARD MICROCIRCUIT DRAWING (SMD) MODEL NUMBERING KEY MGA SERIES SIMILAR PART MGA 28 12 S Z / ES Base Model Input Voltage MGA2805S/883 MGA2812S/883 MGA2815S/883 MGA2805D/883 MGA2812D/883 MGA2815D/883 5962-9309201HXC 5962-9309301HXC 5962-9309401HXC IN PROCESS 5962-9308901HXC 5962-9309001HXC 20 19 18 17 16 15 14 13 12 11 Output Voltage Number of Outputs (S = single, D = dual) Gull Wing Lead Option (Straight leaded case has no designator in this position.) Replace the “Y” with a “Z” in the SMD number to specify gull-wing leads. For exact specifications for an SMD product, refer to the SMD drawing. See Section A3, SMDs, for more information. Screening (Standard screening has no designator in this position.) Typical Performance Curves: 25°C Tc , 28 VDC Vin, 100% load, unless otherwise specified. 80 80 80 16V 16V 28V 40V 50 40 30 EFFICIENCY (%) 60 16V 70 70 EFFICIENCY (%) EFFICIENCY (%) 70 28V 60 40V 50 30 MGA2805S EFFICIENCY vs LINE & LOAD 28V 40V 50 40 40 1 2 3 4 5 6 OUTPUT POWER (Watts) 60 30 1 2 3 4 5 6 OUTPUT POWER (Watts) FIGURE 6 1 2 3 4 5 6 OUTPUT POWER (Watts) MGA2815S EFFICIENCY vs LINE & LOAD MGA2812S EFFICIENCY vs LINE & LOAD FIGURE 8 FIGURE 7 EFFICIENCY (%) 60 28V 40V 50 40 30 30 ATTENUATION (dB) 16V 70 ATTENUATION (dB) 80 40 50 60 1 0.1 MGA2815D EFFICIENCY vs LINE & LOAD FIGURE 9 40 50 60 70 70 1 2 3 4 5 6 OUTPUT POWER (Watts) 30 FREQUENCY (kHz) 10 0.1 MGA2805S FREQUENCY (kHz) 1 AUDIO REJECTION AUDIO REJECTION FIGURE 10 FIGURE 11 10 MGA2815D B2-85 MGA SERIES 5 WATT DC/DC CONVERTERS 100% to 50% 100% to 10% 50mV/div. Vin Vout 50% to 100% 10% to 100% 100µs/div 100µs/div LOAD TRANSIENT RESPONSE (10% 100%), MGA2805S LOAD TRANSIENT RESPONSE (50% 100%) MGA2805S FIGURE 12 FIGURE 13 20V/div. 100µs/div INPUT LINE TRANSIENT RESPONSE (16V TO 40V), MGA2805S FIGURE 14 –Pout=0.5W 90% to 10% Vin Vout 200mV/div. Vin 100mV/div. 1V/div. 20V/div. 20mV/div. 50mV/div. 20V/div. Typical Performance Curves: 25°C Tc , 28 VDC Vin, 100% load, unless otherwise specified. +Vout –Vout 10% to 90% 200µs/div 1ms/div 200µs/div TURN-ON INTO NO LOAD, MGA2805S INPUT LINE TRANSIENT RESPONSE (16V TO 40V), MGA2815D +Vout LOAD TRANSIENT RESPONSE (10% 90%), MGA2815D FIGURE 17 FIGURE 16 FIGURE 15 10 8 20V/div. 100mV/div. –Vout VOLTAGE CHANGE (%) –Pout=2.5W 50% to 10% Vin 5V/div. +Vout –Vout 10% to 50% 2812D 2 0 –2 2815D –4 –6 –8 500µs/div 90/10 70/30 50/50 30/70 10/90 TURN-ON INTO NO LOAD, MGA2815D OUTPUT LOAD (+Vout %/–Vout %) FIGURE 18 MGA2815D/MGA2812D CROSS REGULATION (90–10% LOAD on +V, 10-90% LOAD on –V) FIGURE 19 FIGURE 20 5 –Vout VOLTAGE CHANGE (%) 4 2812D 3 2 COND A 1 0 2815D –1 COND B –2 –3 2812D –4 –5 10 20 30 40 OUTPUT LOAD (%) 50 MGA2815D/MGA2812D CROSS REGULATION COND. A: 50% LOAD +V; 10% to 50% –V COND. B: 50% LOAD –V; 10% to 50% +V FIGURE 21 B2-86 4 –10 100µs/div +Vout LOAD TRANSIENT RESPONSE (10% 50%), MGA2815D 6 22222-001-DTS Rev A DQ# 1034 All technical information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. MGA Series is a trademark of Interpoint. Copyright © 1998 - 1999 Interpoint. All rights reserved. CASES TOP VIEW CASE D MGA Series: Screening – Standard, ES, or 883 Differently colored glass bead around pin one or dimple in header (bottom or side of case) indicates pin one. CASE D TOP VIEW See Figure 13 for pin configurations. 1.110 max (28.19) CASE D 1 2 3 4 5 6 7 8 9 10 1.000 (25.40) 0.900 (22.86) 0.800 (20.32) 0.700 (17.78) 0.600 (15.24) 0.500 (12.70) 0.400 (10.16) 0.300 ( 7.62) 0.200 ( 5.08) 0.100 ( 2.54) (This view shows straight leads.) 20 19 18 17 16 15 14 13 12 11 0.015 (0.38) 0.000 Differently colored glass bead around pin one or dimple in header (bottom or side of case) indicates pin one. Cover marking is oriented with pin one at the upper right corner. 0.000 1.110 max (28.19) Cover marking is oriented with pin one at the upper right corner. 2.115 ref. (53.72) Materials Header Kovar/Nickel/Gold Cover Kovar/Nickel Pins Kovar/Nickel/Gold, matched glass seal Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Maximum reflow temperature is 220°C for a maximum of 30 seconds. SN60, SN62, or SN63 are the recommended types of solder. See below for Solder Mask instructions. Hand soldering should not exceed 300°C for 10 seconds per pin. 0.08 (2.0) 0.50 (12.7) Straight Leads 0.010 (0.25) Seam seal 0.250 max. (6.35) 1.400 ref. (35.56) 0.135 ref. (3.43) Gull Wing Leads Option 1 0.010 (0.25) 1 Leads are solder dipped and lead dimensions are prior to solder dip. 0.055 (1.40) 0.010 (0.25) Bottom of lead to bottom of case FIGURE 12: CASE D MAXIMUM DIMENSIONS FIGURE 13: CASE D Solder Mask Notes 1. Pad dimensions are for the solder mask opening. Lead common to each other can be connected underneath as desired. 2. Ground pins should be connected to the center pad for improved grounding. 3. Center pad should not have a solder mask. Solder, copper, or Au/Ni plate are preferred over solder for adhesive attach. 4. Solder coat to solder down converter. 5. If less rotation of case is desired, make the pad width 0.020inches (0.51 mm). Pad length can be extended 0.010 inches (0.25 mm) towards the case body and as-desired dimension away from the case body. 6. Do not exceed 220°C as measured on the body of the converter (top or bottom). 7. Attach the body of the case to the board with a thermally conductive adhesive or SN60, 62, or 63 solder. The adhesive can be electrically conductive as well. It can be applied as an underfill post solder or dispensed and cured prior or during solder. 0.070 (1.78) 0.08 (2.0) 0.075 (1.91) 0.060 (1.52) 1.000 (25.40) 0.030 (0.76) 1.000 (25.40) 0.100 (2.54) 18X 0.100 (2.54) 4X FIGURE 14: CASE D SOLDER MASK Note: Although every effort has been made to render the case drawings at actual size, variations in the printing process may cause some distortion. Please refer to the numerical dimensions for accuracy. B8-9 QA SCREENING 125°C PRODUCTS 125°C PRODUCTS TEST (125°C Products) STANDARD /ES /883 (Class H)* PRE-CAP INSPECTION Method 2017, 2032 yes yes yes TEMPERATURE CYCLE (10 times) Method 1010, Cond. C, -65°C to 150°C Method 1010, Cond. B, -55°C to 125°C no no no yes yes no CONSTANT ACCELERATION Method 2001, 3000 g Method 2001, 500 g no no no yes yes no BURN-IN Method 1015, 160 hours at 125°C 96 hours at 125°C case (typical) no no no yes yes no FINAL ELECTRICAL TEST MIL-PRF-38534, Group A Subgroups 1 through 6: -55°C, +25°C, +125°C Subgroups 1 and 4: +25°C case no yes no yes yes no HERMETICITY TESTING Fine Leak, Method 1014, Cond. A Gross Leak, Method 1014, Cond. C Gross Leak, Dip (1 x 10-3) no no yes yes yes no yes yes no FINAL VISUAL INSPECTION Method 2009 yes yes yes Test methods are referenced to MIL-STD-883 as determined by MIL-PRF-38534. *883 products are built with element evaluated components and are 100% tested and guaranteed over the full military temperature range of –55°C to +125°C. Applies to the following products MOR Series MHD Series MFLHP Series MHV Series MFL Series MHF+ Series MHP Series MHF Series** MTR Series MGA Series MQO Series** MSA Series MGH Series MCH Series FM-704A EMI Filter FMD**/FME EMI Filter FMC EMI Filter FMH EMI Filter FMGA EMI Filter FMSA EMI Filter HUM Modules** LCM Modules** LIM Modules **MFLHP Series, MQO Series, MHF Series, FMD EMI Filters, Hum Modules, and LCM Modules do not offer ‘883” screening. C2-10