LMV712 LMV712 Low Power, Low Noise, High Output, RRIO Dual Operational Amplifier with Independent Shutdown Literature Number: SNOS534G LMV712 Low Power, Low Noise, High Output, RRIO Dual Operational Amplifier with Independent Shutdown General Description Features The LMV712 duals are high performance BiCMOS operational amplifiers intended for applications requiring Rail-toRail inputs combined with speed and low noise. They offer a bandwidth of 5MHz and a slew rate of 5 V/µs and can handle capacitive loads of up to 200pF without oscillation. The LMV712 is guaranteed to operate from 2.7V to 5.5V and offers two independent shutdown pins. This feature allows disabling of each device separately and reduces the supply current to less than 1µA typical. The output voltage rapidly ramps up smoothly with no glitch as the amplifier comes out of the shutdown mode. The LMV712 with the shutdown feature is offered in space saving 10-Bump micro SMD and 10-Pin Leadless Leadframe Package (LLP) packages. It is also offered in 10-Pin MSOP package. These packages are designed to meet the demands of small size, low power, and low cost required by cellular phones and similar battery operated portable electronics. (Typical Unless Otherwise Noted) ■ 5MHz GBP ■ Slew rate 5V/µs ■ Low noise 20nV/√Hz ■ Supply current 1.22mA/channel ■ VOS< 3mV max ■ Guaranteed 2.7V and 5V specifications ■ Rail-to-Rail inputs and outputs ■ Unity gain stable ■ Small package: 10-Pin LLP, 10-Pin MSOP and 10-Bump micro SMD ■ 1.5µA shutdown ICC ■ 2.2µs turn on Applications ■ ■ ■ ■ ■ ■ Power amplifier control loop Cellular phones Portable equipment Wireless LAN Radio systems Cordless phones Typical Application Circuit 10137034 P.A. Control Loop © 2010 National Semiconductor Corporation 101370 www.national.com LMV712 Low Power, Low Noise, High Output, RRIO Dual Operational Amplifier with Independent Shutdown March 5, 2010 LMV712 Soldering specification for LLP SnPb: Infrared or Convection (20sec) Soldering specification for all other packages: see product folder at www.national.com and www.national.com/ms/MS/MS-SOLDERING.pdf Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Tolerance (Note 2) Human Body Model 1.5kV Machine Model 150V Differential Input Voltage ±Supply Voltage Voltage at Input/Output Pin (V+) +0.4V to (V−) −0.4V Supply Voltage (V+ - V−) 6V Output Short Circuit V+ (Note 3) Output Short Circuit V− (Note 3) Current at Input Pin ±10mA Current at Output Pin ±50mA Storage Temp Range −65°C to 150°C Junction Temperature TJMAX (Note 4) 150°C 235°C Recommended Operating Conditions (Note 1) Supply Voltage Temperature Range 2.7V to 5.5V −40°C ≤ TJ ≤ 85°C Thermal Resistance 10-Pin MSOP 10-Pin LLP 10-Bump micro SMD 235°C/W 53.4°C/W 196°C/W 2.7V Electrical Characteristics Unless otherwise specified, all limits guaranteed for V+ = 2.7V, V − = 0V, VCM = 1.35V and TA = 25°C and RL > 1MΩ. Boldface limits apply at the temperature extremes. Symbol Parameter VOS Input Offset Voltage IB Input Bias Current CMRR Common Mode Rejection Ratio PSRR CMVR Power Supply Rejection Ratio Common Mode Voltage Range Condition VCM = 0.85V and VCM = 1.85V Output Short Circuit Current Typ (Note 5) Max (Note 6) MSOP LLP 0.4 3 3.2 μSMD 3 7 9 5.5 115 130 0V ≤ VCM ≤ 2.7V 50 45 75 2.7V ≤ V+ ≤ 5V, VCM = 0.85V 70 68 90 2.7V ≤ V+ ≤ 5V, VCM = 1.85V 70 68 90 For CMRR ≥ 50dB Sourcing ISC Min (Note 6) VO = 0V Sinking VO = 2.7V RL = 10kΩ to 1.35V −0.3 2.9 3 15 12 25 25 22 50 2.62 2.60 2.68 0.01 VO Output Swing RL = 600Ω to 1.35V VO(SD) Output Voltage in Shutdown On Mode IS Supply Current per Channel Shutdown Mode www.national.com 2 2.52 2.50 Units mV pA dB dB dB −0.2 V mA mA V 0.12 0.15 2.55 V V 0.05 0.23 0.30 V 10 200 mV 1.22 1.7 1.9 mA 0.12 1.5 2.0 uA Parameter Condition Min (Note 6) Typ (Note 5) Max (Note 6) Units 80 76 115 dB 80 76 113 dB 80 76 97 dB 80 76 100 dB 2.4 to 2.7 2.0 to 2.7 V 0 to 0.8 0 to 1 V 5 MHz 5 V/µs 60 Deg Sourcing RL = 10kΩ VO = 1.35V to 2.3V Sinking RL = 10kΩ AVOL Large Signal Voltage Gain VO = 0.4V to 1.35V Sourcing RL = 600Ω VO = 1.35V to 2.2V Sinking RL = 600Ω VO = 0.5V to 1.35V VSD Shutdown Pin Voltage Range GBWP Gain-Bandwidth Product SR Slew Rate φm Phase Margin en Input Referred Voltage Noise On Mode Shutdown Mode (Note 7) f = 1kHz 20 2.2 Turn-On Time from Shutdown TON Turn-On Time from Shutdown nV/ 4 4.6 μs 6 8 micro SMD μs 5V Electrical Characteristics Unless otherwise specified, all limits guaranteed for V+ = 5V, V − = 0V, VCM = 2.5V and TA = 25°C and RL > 1MΩ. Boldface limits apply at the temperature extremes. Symbol Parameter VOS Input Offset Voltage IB Input Bias Current CMRR Common Mode Rejection Ratio PSRR CMVR Power Supply Rejection Ratio Common Mode Voltage Range Condition VCM = 0.85V and VCM = 1.85V Output Short Circuit Current Typ (Note 5) Max (Note 6) MSOP LLP 0.4 3 3.2 μSMD 3 7 9 5.5 115 130 0V ≤ VCM ≤ 5V 50 45 80 2.7V ≤ V+ ≤ 5V, VCM = 0.85V 70 68 90 2.7V ≤ V+ ≤ 5V, VCM = 1.85V 70 68 90 For CMRR ≥ 50dB Sourcing ISC Min (Note 6) VO = 0V Sinking VO = 5V 3 −0.3 5.2 5.3 20 18 35 25 21 50 Units mV pA dB dB dB −0.2 V V mA mA www.national.com LMV712 Symbol LMV712 Symbol Parameter Condition RL = 10kΩ to 2.5V Min (Note 6) Typ (Note 5) 4.92 4.90 4.98 0.01 VO Output Swing RL = 600Ω to 2.5V VO(SD) 4.82 4.80 Output Voltage in Shutdown On Mode IS Supply Current per Channel Shutdown Mode Max (Note 6) Units V 0.12 0.15 4.85 V V 0.05 0.23 0.30 V 10 200 mV 1.17 1.7 1.9 mA 0.12 1.5 2.0 uA Sourcing RL = 10kΩ 80 76 130 dB 80 76 130 dB 80 76 110 dB 80 76 107 dB On Mode 4.5 to 5 3.5 to 5 V Shutdown Mode 0 to 0.8 0 to 1.5 V 5 MHz 5 V/µs 60 Deg VO = 2.5V to 4.6V Sinking RL = 10kΩ AVOL Large Signal Voltage Gain VO = 0.4V to 2.5V Sourcing RL = 600Ω VO = 2.5V to 4.6V Sinking RL = 600Ω VO = 0.4V to 2.5V VSD Shutdown Pin Voltage Range GBWP Gain-Bandwidth Product SR Slew Rate φm Phase Margin en Input Referred Voltage Noise (Note 7) f = 1kHz 20 1.6 Turn-On Time for Shutdown TON Turn-On Time for Shutdown nV/ 4 4.6 6 8 micro SMD μs μs Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics. Note 2: Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of JEDEC) Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC). Note 3: Shorting circuit output to either V+ or V− will adversely affect reliability. Note 4: The maximum power dissipation is a function of TJ(MAX), θJA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) – TA)/ θJA. All numbers apply for packages soldered directly onto a PC Board. Note 5: Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material. Note 6: All limits are guaranteed by testing or statistical analysis. Note 7: Number specified is the slower of the positive and negative slew rates. www.national.com 4 Unless otherwise specified, VS = +5V, single supply, TA = 25°C. Supply Current Per Channel vs. Supply Voltage Supply Current vs. Supply Voltage (Shutdown) 10137001 10137002 VOS vs. VCM IB vs. VCM Over Temp 10137003 10137005 Output Positive Swing vs. Supply Voltage, RL = 600Ω Output Negative Swing vs. Supply Voltage, RL = 600Ω 10137006 10137007 5 www.national.com LMV712 Typical Performance Characteristics LMV712 Sourcing Current vs. Output Voltage, VS = 2.7V Sourcing Current vs. Output Voltage, VS = 5V 10137008 10137010 Sinking Current vs. Output Voltage, VS = 2.7V Sinking Current vs. Output Voltage, VS = 5V 10137009 10137011 PSRR vs. Frequency VS = 2.7V PSRR vs. Frequency VS = 5V 10137018 www.national.com 10137019 6 LMV712 CMRR vs. Frequency CMRR vs. Frequency 10137016 10137017 Open Loop Frequency Response vs. RL Open Loop Frequency Response vs. RL 10137012 10137014 Open Loop Frequency Response vs. CL Open Loop Frequency Response vs. CL 10137013 10137015 7 www.national.com LMV712 Voltage Noise vs. Frequency Voltage Noise vs. Frequency 10137020 10137021 Non-Inverting Large Signal Pulse Response, VS = 2.7V Non-Inverting Large Signal Pulse Response, VS = 5V 10137022 10137024 Non-Inverting Small Signal Pulse Response, VS = 2.7V Non-Inverting Small Signal Pulse Response, VS = 5V 10137023 www.national.com 10137025 8 Inverting Large Signal Pulse Response, VS = 5V 10137026 10137028 Inverting Small Signal Pulse Response, VS = 2.7V Inverting Small Signal Pulse Response VS = 5V 10137027 10137029 Turn on Time Response VS = 5V Input Common Mode Capacitance vs. VCM VS = 5V 10137030 10137004 9 www.national.com LMV712 Inverting Large Signal Pulse Response, VS = 2.7V LMV712 Application Information THEORY OF OPERATION The LMV712 dual op amp is derived from the LMV711 single op amp. Figure 1 contains a simplified schematic of one channel of the LMV712. 10137031 FIGURE 1. Rail-to-Rail input is achieved by using in parallel, one NMOS differential pair (MN1 and MN2) and one PMOS differential pair (MP1 and MP2). When the common mode input voltage (VCM) is near V+, the NMOS pair is on and the PMOS pair is off. When VCM is near V−, the NMOS pair is off and the PMOS pair is on. When VCM is between V+ and V−, internal logic decides how much current each differential pair will get. This special logic ensures stable and low distortion amplifier operation within the entire common mode voltage range. Because both input stages have their own offset voltage (VOS) characteristic, the offset voltage of the LMV712 becomes a function of VCM. VOS has a crossover point at 1.4V above V−. Refer to the "VOS vs. VCM" curve in the Typical Performance Characteristics section. Caution should be taken in situations where input signal amplitude is comparable to VOS value and/or the design requires high accuracy. In these situations, it is necessary for the input signal to avoid the crossover point. The current coming out of the input differential pairs gets mirrored through two folded cascode stages (Q1, Q2, Q3, Q4) into the "class AB control" block. This circuitry generates voltage gain, defines the op amp's dominant pole and limits the maximum current flowing at the output stage. MN3 introduces a voltage level shift and acts as a high impedance to low impedance buffer. The output stage is composed of a PMOS and a NPN transistor in a common source/emitter configuration, delivering a rail-to-rail output excursion. The MN4 transistor ensures that the LMV712 output remains near V− when the amplifier is in shutdown mode. www.national.com SHUTDOWN PIN The LMV712 offers independent shutdown pins for the dual amplifiers. When the shutdown pin is tied low, the respective amplifier shuts down and the supply current is reduced to less than 1µA. In shutdown mode, the amplifier's output level stays at V−. In a 2.7V operation, when a voltage between 1.5V to 2.7V is applied to the shutdown pin, the amplifier is enabled. As the amplifier is coming out of the shutdown mode, the output waveform ramps up without any glitch. This is demonstrated in Figure 2. 10137030 FIGURE 2. 10 PRINTED CIRCUIT BOARD CONSIDERATION To properly bypass the power supply, several locations on a printed circuit board need to be considered. A 6.8µF or greater tantalum capacitor should be placed at the point where the power supply for the amplifier is introduced onto the board. Another 0.1µF ceramic capacitor should be placed as close as possible to the power supply pin of the amplifier. If the amplifier is operated in a single power supply, only the V+ pin needs to be bypassed with a 0.1µF capacitor. If the amplifier is operated in a dual power supply, both V+ and V− pins need to be bypassed. It is good practice to use a ground plane on a printed circuit board to provide all components with a low inductive ground connection. Surface mount components in 0805 size or smaller are recommended in the LMV712 application circuits. Designers can take advantage of the micro SMD, MSOP and LLP miniature sizes to condense board layout in order to save space and reduce stray capacitance. 10137033 CAPACITIVE LOAD TOLERANCE The LMV712 can directly drive 200pF in unity-gain without oscillation. The unity-gain follower is the most sensitive configuration to capacitive loading. Direct capacitive loading reduces the phase margin of amplifiers. The combination of the amplifier's output impedance and the capacitive load induces phase lag. This results in either an under-damped pulse response or oscillation. To drive a heavier capacitive load, Figure 3 can be used. FIGURE 4. LATCHUP CMOS devices tend to be susceptible to latchup due to their internal parasitic SCR (silicon controlled rectifier) effects. The input and output pins look similar to the gate of the SCR. There is a minimum current required to trigger the SCR gate lead. The LMV712 is designed to withstand 150mA surge current on all the pins. Some resistive method should be used to isolate any capacitance from supplying excess current to the pins. In addition, like an SCR, there is a minimum holding current for any latchup mode. Limiting current to the supply pins will also inhibit latchup susceptibility. 10137032 FIGURE 3. 11 www.national.com LMV712 In Figure 3, the isolation resistor RISO and the load capacitor CL form a pole to increase stability by adding more phase margin to the overall system. The desired performance depends on the value of RISO. The bigger the RISO resistor value, the more stable VOUT will be. But the DC accuracy is degraded when the RISO gets bigger. If there were a load resistor in Figure 3, the output voltage would be divided by RISO and the load resistor. The circuit in Figure 4 is an improvement to the one in Figure 3 because it provides DC accuracy as well as AC stability. In this circuit, RF provides the DC accuracy by using feed-forward techniques to connect VIN to RL. CF and RISO serve to counteract the loss of phase margin by feeding the high frequency component of the output signal back to the amplifier's inverting input, thereby preserving phase margin in the overall feedback loop. Increased capacitive drive is possible by increasing the value of CF. This in turn will slow down the pulse response. A glitch-free output waveform is highly desirable in many applications, one of which is power amplifier control loops. In this application, the LMV712 is used to drive the power amplifier's power control. If the LMV712 did not have a smooth output ramp during turn on, it would directly cause the power amplifier to produce a glitch at its output. This adversely affects the performance of the system. To enable the amplifier, the shutdown pin must be pulled high. It should not be left floating in the event that any leakage current may inadvertently turn off the amplifier. LMV712 Connection Diagrams 10-Pin MSOP (Top View) 10-Pin LLP (Top View) 10137036 10137040 *Connect thermal pad to V- or leave floating 10-Bump micro SMD (Top View) 10-Bump micro SMD (Bottom View) 10137038 10137037 Ordering Information Package 10-Pin MSOP 10-Pin LLP 10-Bump micro SMD (NOPB) www.national.com Part Number LMV712MM LMV712MMX LMV712LD LMV712LDX LMV712TL LMV712TLX Package Marking Transport Media 1k Units Tape and Reel A61 3.5k Units Tape and Reel 1k Units Tape and Reel A62 4.5k Units Tape and Reel 250 Units Tape and Reel AU2A 3k Units Tape and Reel 12 NSC Drawing MUB10A LDA10A TLP10BBA 0.600mm thick LMV712 Physical Dimensions inches (millimeters) unless otherwise noted 10-Pin MSOP NS Package Number MUB10A 10-Pin LLP NS Package Number LDA10A 13 www.national.com LMV712 NOTES: UNLESS OTHERWISE SPECIFIED 1. EPOXY COATING 2. FOR SOLDER BUMP COMPOSITION. SEE ”SOLDER INFORMATION” IN THE PACKAGING SECTION OF THE NATIONAL SEMICONDUCTOR WEB PAGE (www.national.com) 3. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD. 4. PIN A1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION. 5. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X1 IS PACKAGE WIDTH, X2 IS PACKAGE LENGTH AND X3 IS PACKAGE HEIGHT. 6. REFERENCE JEDEC REGISTRATION MO-211, VARIATION BD. 10-Bump micro SMD NS Package Number TLP10BBA X1 = 1.539 ±0.030mm X2 = 2.022 ±0.030mm X3 = 0.600 ±0.075mm www.national.com 14 LMV712 Notes 15 www.national.com LMV712 Low Power, Low Noise, High Output, RRIO Dual Operational Amplifier with Independent Shutdown Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise® Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagic™ www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise® Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2010 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: [email protected] National Semiconductor Asia Pacific Technical Support Center Email: [email protected] National Semiconductor Japan Technical Support Center Email: [email protected] IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated