ASAHI KASEI [AK4358] AK4358 192kHz 24-Bit 8ch DAC with DSD Input GENERAL DESCRIPTION The AK4358 is eight channels 24bit DAC corresponding to digital audio system. Using AKM's advanced multi bit architecture for its modulator the AK4358 delivers a wide dynamic range while preserving linearity for improved THD+N performance. The AK4358 has full differential SCF outputs, removing the need for AC coupling capacitors and increasing performance for systems with excessive clock jitter. The AK4358 accepts 192kHz PCM data and 1-Bit DSD data, ideal for a wide range of applications including DVD-Audio and SACD. FEATURES Sampling Rate Ranging from 8kHz to 192kHz 24Bit 8 times Digital Filter with Slow roll-off option THD+N: -94dB DR, S/N: 112dB High Tolerance to Clock Jitter Low Distortion Differential Output DSD Data input available Digital De-emphasis for 32, 44.1 & 48kHz sampling Zero Detect function Channel Independent Digital Attenuator with soft-transition (3 Speed mode) Soft Mute 3-wire Serial and I2C Bus µP I/F for mode setting I/F format: MSB justified, LSB justified (16bit, 20bit, 24bit), I2S, TDM or DSD Master clock: 256fs, 384fs, 512fs or 768fs (PCM Normal Speed Mode) 128fs, 192fs, 256fs or 384fs (PCM Double Speed Mode) 128fs or 192fs (PCM Quad Speed Mode) 512fs or 768fs (DSD Mode) Power Supply: 4.75 to 5.25V 48pin LQFP Package DZF LOUT1+ LOUT1- SCF DAC DATT ROUT1+ ROUT1- SCF DAC DATT LOUT2+ LOUT2- SCF DAC DATT ROUT2+ ROUT2- SCF DAC DATT LOUT3+ LOUT3- SCF DAC DATT ROUT3+ ROUT3- SCF DAC DATT LOUT4+ LOUT4- SCF DAC DATT ROUT4+ ROUT4- SCF DAC DATT Audio I/F MCLK LRCK BICK SDTI1 SDTI2 SDTI3 SDTI4 PCM Control Register DSD 3-wire or I2C DCLK DSDL1 DSDR1 DSDL2 DSDR2 DSDL3 DSDR3 DSDL4 DSDR4 AK4358 MS0203-E-00 2003/02 -1- ASAHI KASEI [AK4358] Ordering Guide -40 ∼ +85°C 48LQFP Evaluation Board for AK4358 AK4358VQ AKD4358 ROUT1+ ROUT1- LOUT2+ LOUT2- ROUT2+ ROUT2- LOUT3+ LOUT3- ROUT3+ ROUT3- LOUT4+ LOUT4- 48 47 46 45 44 43 42 41 40 39 38 37 Pin Layout LOUT1- 1 36 AVSS LOUT1+ 2 35 AVDD DZF3 3 34 VREFH DZF2 4 33 ROUT4+ DZF1 5 32 ROUT4- AK4358VQ CAD0 6 31 DIF0 ACKSN 7 30 DSDR3 PDN 8 29 DSDL3 BICK 9 28 DSDR2 DSDL2 Top View 22 23 24 DCLK DSDL4 DSDR4 20 21 18 19 I2C CCLK/SCL CDTI/SDA 17 MS0203-E-00 CSN/CAD1 16 LRCK DSDL1 SDTI3 25 15 12 14 DSDR1 DVSS SDTI2 26 13 27 SDTI1 10 11 SDTI4 MCLK DVDD 2003/02 -2- ASAHI KASEI [AK4358] Compatibility with AK4357 1. Function & Performance Functions # of channels DR 48kHz/96kHz TDM I2C DSDM control Input channel of DZF pin AK4357 6 106dB Not available Not available Pin/Register Fixed AK4358 8 112dB Available Available Register Programmable 2. Pin Configuration Pin # 3 4 5 7 12 13 18 19 20 21 22 23 24 32 33 37 38 AK4357 DZFL1 DZFR1 DZF23 CAD1 NC DVSS SMUTE CCLK CDTI CSN DSDM DCLK NC DIF1 DIF2 AVSS AVSS AK4358 DZF3 DZF2 DZF1 ACKSN DVSS SDTI4 I2C CCLK/SCL CDTI/SDA CSN/CAD1 DCLK DSDL4 DSDR4 ROUT4ROUT4+ LOUT4LOUT4- Bit D5 D6 D7 D7 D7 D7 D7 D7 D7, D6 AK4357 DZFM 0 ATT7 ATT7 ATT7 ATT7 ATT7 ATT7 0, 0 Not available Not available Not available Not available Not available 3. Register Addr 00H 01H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0FH AK4358 0 PW4 ATTE ATTE ATTE ATTE ATTE ATTE TDM1, TDM0 LOUT4 ATT Control ROUT4 ATT Control DZF1 control DZF2 control DZF3 control MS0203-E-00 2003/02 -3- ASAHI KASEI [AK4358] PIN/FUNCTION No. 1 2 3 4 5 6 7 Pin Name LOUT1LOUT1+ DZF3 DZF2 DZF1 CAD0 ACKSN I/O O O O O O I I 8 PDN I 9 10 BICK MCLK I I 11 12 13 14 15 16 17 18 DVDD DVSS SDTI4 SDTI1 SDTI2 SDTI3 LRCK I2C I I I I I I 19 CCLK/SCL I 20 CDTI/SDA I/O 21 CSN/CAD1 I 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 DCLK DSDL4 DSDR4 DSDL1 DSDR1 DSDL2 DSDR2 DSDL3 DSDR3 DIF0 ROUT4ROUT4+ VREFH AVDD AVSS LOUT4LOUT4+ ROUT3ROUT3+ LOUT3LOUT3+ ROUT2ROUT2+ LOUT2- I I I I I I I I I I O O I O O O O O O O O O Function DAC1 Lch Negative Analog Output Pin DAC1 Lch Positive Analog Output Pin Zero Input Detect 3 Pin Zero Input Detect 2 Pin Zero Input Detect 1 Pin Chip Address 0 Pin Auto Setting Mode Disable Pin (Pull-down Pin) “L”: Auto Setting Mode, “H”: Manual Setting Mode Power-Down Mode Pin When at “L”, the AK4358 is in the power-down mode and is held in reset. The AK4358 should always be reset upon power-up. Audio Serial Data Clock Pin Master Clock Input Pin An external TTL clock should be input on this pin. Digital Power Supply Pin, +4.75∼+5.25V Digital Ground Pin DAC4 Audio Serial Data Input Pin DAC1 Audio Serial Data Input Pin DAC2 Audio Serial Data Input Pin DAC3 Audio Serial Data Input Pin L/R Clock Pin Control Mode Select Pin “L”: 3-wire Serial, “H”: I2C Bus Control Data Clock Pin I2C = “L”: CCLK (3-wire Serial), I2C = “H”: SCL (I2C Bus) Control Data Input Pin I2C = “L”: CDTI (3-wire Serial), I2C = “H”: SDA (I2C Bus) Chip Select Pin I2C = “L”: CSN (3-wire Serial), I2C = “H”: CAD1 (I2C Bus) DSD Clock Pin DAC4 DSD Lch Data Input Pin DAC4 DSD Rch Data Input Pin DAC1 DSD Lch Data Input Pin DAC1 DSD Rch Data Input Pin DAC2DSD Lch Data Input Pin DAC2 DSD Rch Data Input Pin DAC3 DSD Lch Data Input Pin DAC3 DSD Rch Data Input Pin Audio Data Interface Format 0 Pin DAC4 Rch Negative Analog Output Pin DAC4 Rch Positive Analog Output Pin Positive Voltage Reference Input Pin Analog Power Supply Pin, +4.75∼+5.25V Analog Ground Pin DAC4 Lch Negative Analog Output Pin DAC4 Lch Positive Analog Output Pin DAC3 Rch Negative Analog Output Pin DAC3 Rch Positive Analog Output Pin DAC3 Lch Negative Analog Output Pin DAC3 Lch Positive Analog Output Pin DAC2 Rch Negative Analog Output Pin DAC2 Rch Positive Analog Output Pin DAC2 Lch Negative Analog Output Pin MS0203-E-00 2003/02 -4- ASAHI KASEI [AK4358] 46 LOUT2+ O DAC2 Lch Positive Analog Output Pin 47 ROUT1O DAC1 Rch Negative Analog Output Pin 48 ROUT1+ O DAC1 Rch Positive Analog Output Pin Note: All input pins except pull-down pin should not be left floating. ABSOLUTE MAXIMUM RATINGS (AVSS, DVSS=0V; Note 1) Parameter Symbol Min Power Supplies Analog AVDD -0.3 Digital DVDD -0.3 |AVSS-DVSS| (Note 2) ∆GND Input Current (any pins except for supplies) IIN Analog Input Voltage VINA -0.3 Digital Input Voltage VIND -0.3 Ambient Operating Temperature Ta -40 Storage Temperature Tstg -65 Max 6.0 6.0 0.3 ±10 AVDD+0.3 DVDD+0.3 85 150 Units V V V mA V V °C °C Note 1. All voltages with respect to ground. Note 2. AVSS and DVSS must be connected to the same analog ground plane. WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes. RECOMMENDED OPERATING CONDITIONS (AVSS, DVSS=0V; Note 1) Parameter Symbol Min Typ Power Supplies Analog AVDD 4.75 5.0 (Note 3) Digital DVDD 4.75 5.0 Voltage Reference VREF AVDD-0.5 - Max 5.25 5.25 AVDD Units V V V Note 3. The power up sequence between AVDD and DVDD is not critical. *AKM assumes no responsibility for the usage beyond the conditions in this datasheet. MS0203-E-00 2003/02 -5- ASAHI KASEI [AK4358] ANALOG CHARACTERISTICS (Ta=25°C; AVDD, DVDD=5V; VREFH=AVDD; fs=44.1kHz; BICK=64fs; Signal Frequency=1kHz; 24bit Input Data; Measurement frequency=20Hz ∼ 20kHz; RL ≥2kΩ; unless otherwise specified) Parameter Min Typ Max Units Resolution 24 Bits (Note 4) Dynamic Characteristics THD+N fs=44.1kHz 0dBFS -94 -86 dB BW=20kHz -60dBFS -48 dB fs=96kHz 0dBFS -92 -84 dB BW=40kHz -60dBFS -45 dB fs=192kHz 0dBFS -92 dB BW=40kHz -60dBFS -45 dB Dynamic Range (-60dBFS with A-weighted) (Note 5) 102 112 dB S/N (A-weighted) (Note 6) 102 112 dB Interchannel Isolation (1kHz) 90 100 dB Interchannel Gain Mismatch 0.2 0.5 dB DC Accuracy Gain Drift 100 ppm/°C Output Voltage (Note 7) Vpp ±2.35 ±2.5 ±2.65 Load Resistance (Note 8) 2 kΩ Power Supplies Power Supply Current (AVDD+DVDD) mA 70 56 Normal Operation (PDN = “H”, fs≤96kHz) (Note 9) mA 85 62 Normal Operation (PDN = “H”, fs=192kHz) (Note 10) µA 100 10 Power-Down Mode (PDN = “L”) (Note 11) Note 4. Measured by Audio Precision System Two. Refer to the evaluation board manual. Note 5. 100dB at 16bit data. Note 6. S/N does not depend on input bit length. Note 7. Full scale voltage (0dB). Output voltage scales with the voltage of VREFH pin. AOUT (typ. @0dB) = (AOUT+)-(AOUT-) = ±2.5Vpp×VREFH/5.0 Note 8. For AC-load. 4kΩ for DC-load Note 9 AVDD=40mA(Typ), DVDD=12mA(Typ)@44.1kHz&5V, 16mA(Typ)@96kHz&5V Note 10 AVDD=40mA(Typ), DVDD=22mA(Typ)@192kHz&5V Note 11. All digital inputs including clock pins (MCLK, BICK and LRCK) are held DVDD or DVSS. MS0203-E-00 2003/02 -6- ASAHI KASEI [AK4358] SHARP ROLL-OFF FILTER CHARACTERISTICS (Ta = 25°C; AVDD, DVDD = 4.75 ∼ 5.25V; fs = 44.1kHz; DEM = OFF; SLOW = “0”; PCM Mode) Parameter Symbol Min Typ Max Digital filter PB 0 20.0 Passband ±0.05dB (Note 12) 22.05 -6.0dB Stopband (Note 12) SB 24.1 Passband Ripple PR ± 0.02 Stopband Attenuation SA 54 Group Delay (Note 13) GD 19.1 Digital Filter + SCF Frequency Response 20.0kHz Fs=44.1kHz FR ± 0.2 40.0kHz Fs=96kHz FR ± 0.3 80.0kHz Fs=192kHz FR +0/-0.6 Units kHz kHz kHz dB dB 1/fs dB dB dB Note 12. The passband and stopband frequencies scale with fs(system sampling rate). For example, PB=0.4535×fs (@±0.05dB), SB=0.546×fs. Note 13. The calculating delay time which occurred by digital filtering. This time is from setting the 16/24bit data of both channels to input register to the output of analog signal. SLOW ROLL-OFF FILTER CHARACTERISTICS (Ta = 25°C; AVDD, DVDD = 4.75~5.25V; fs = 44.1kHz; DEM = OFF; SLOW = “1”; PCM Mode) Parameter Symbol Min Typ Max Units PB 0 39.2 18.2 8.1 - Digital Filter Passband ±0.04dB -3.0dB Stopband Passband Ripple Stopband Attenuation Group Delay (Note 14) (Note 14) (Note 13) SB PR SA GD 72 - 19.1 - kHz kHz kHz dB dB 1/fs - +0/-5 +0/-4 +0/-5 - dB dB dB ± 0.005 Digital Filter + SCF Frequency Response 20.0kHz 40.0kHz 80.0kHz fs=44.kHz fs=96kHz fs=192kHz FR FR FR Note 14. The passband and stopband frequencies scale with fs. For example, PB = 0.185×fs (@±0.04dB), SB = 0.888×fs. DC CHARACTERISTICS (Ta = 25°C; AVDD, DVDD = 4.75 ∼ 5.25V) Parameter Symbol Min High-Level Input Voltage VIH 2.2 Low-Level Input Voltage VIL High-Level Output Voltage (Iout = -80µA) VOH DVDD-0.4 Low-Level Output Voltage (Iout = 80µA) VOL Input Leakage Current (Note 15) Iin - Typ - Max 0.8 0.4 ± 10 Units V V V V µA Note 15. ACKSN pin has internal pull-down devices, nominally 100kΩ. MS0203-E-00 2003/02 -7- ASAHI KASEI [AK4358] SWITCHING CHARACTERISTICS (Ta = 25°C; AVDD, DVDD = 4.75 ∼ 5.25V; CL = 20pF) Parameter Symbol Min fCLK 2.048 Master Clock Frequency Duty Cycle dCLK 40 LRCK Frequency Normal Mode (TDM0= “L”, TDM1= “L”) Normal Speed Mode Double Speed Mode Quad Speed Mode Duty Cycle TDM256 mode (TDM0= “H”, TDM1= “L”) Normal Speed Mode High time Low time TDM128 mode (TDM0= “H”, TDM1= “H”) Normal Speed Mode Double Speed Mode High time Low time PCM Audio Interface Timing BICK Period BICK Pulse Width Low Pulse Width High BICK “↑” to LRCK Edge (Note 16) LRCK Edge to BICK “↑” (Note 16) SDTI Hold Time SDTI Setup Time DSD Audio Interface Timing DCLK Period DCLK Pulse Width Low Pulse Width High DCLK Edge to DSDL/R (Note 17) Control Interface Timing (3-wire Serial mode): CCLK Period CCLK Pulse Width Low Pulse Width High CDTI Setup Time CDTI Hold Time CSN High Time CSN “↓” to CCLK “↑” CCLK “↑” to CSN “↑” Control Interface Timing (I2C Bus mode): SCL Clock Frequency Bus Free Time Between Transmissions Start Condition Hold Time (prior to first clock pulse) Clock Low Time Clock High Time Setup Time for Repeated Start Condition SDA Hold Time from SCL Falling (Note 18) SDA Setup Time from SCL Rising Rise Time of Both SDA and SCL Lines Fall Time of Both SDA and SCL Lines Setup Time for Stop Condition Pulse Width of Spike Noise Suppressed by Input Filter MS0203-E-00 Typ 11.2896 Max 36.864 60 Units MHz % fsn fsd fsq Duty 8 60 120 45 48 96 192 55 kHz kHz kHz % fsn tLRH tLRL 32 1/256fs 1/256fs 48 kHz ns ns fsn fsd tLRH tLRL 32 60 1/128fs 1/128fs 48 96 kHz kHz ns ns tBCK tBCKL tBCKH tBLR tLRB tSDH tSDS 81 30 30 20 20 10 10 ns ns ns ns ns ns ns tDCK tDCKL tDCKH tDDD 1/64fs 160 160 -20 ns ns ns ns tCCK tCCKL tCCKH tCDS tCDH tCSW tCSS tCSH 200 80 80 40 40 150 50 50 fSCL tBUF tHD:STA tLOW tHIGH tSU:STA tHD:DAT tSU:DAT tR tF tSU:STO tSP 4.7 4.0 4.7 4.0 4.7 0 0.25 4.0 0 20 ns ns ns ns ns ns ns ns 100 1.0 0.3 50 kHz µs µs µs µs µs µs µs µs µs µs ns 2003/02 -8- ASAHI KASEI Parameter Reset Timing PDN Pulse Width [AK4358] (Note 19) Symbol Min tPD 150 Typ Max Units ns Note 16. BICK rising edge must not occur at the same time as LRCK edge. Note 17. DSD data transmitting device must meet this time. Note 18. Data must be held for sufficient time to bridge the 300 ns transition time of SCL. Note 19. The AK4358 can be reset by bringing PDN= “L”. Note 20. I2C is a registered trademark of Philips Semiconductors. Purchase of Asahi Kasei Microsystems Co., Ltd I2C components conveys a license under the Philips I2C patent to use the components in the I2C system, provided the system conform to the I2C specifications defined by Philips. MS0203-E-00 2003/02 -9- ASAHI KASEI [AK4358] Timing Diagram 1/fCLK VIH MCLK VIL tCLKH tCLKL dCLK=tCLKH x fCLK, tCLKL x fCLK 1/fs VIH LRCK VIL tBCK VIH BICK VIL tBCKH tBCKL Clock Timing VIH LRCK VIL tBLR tLRB VIH BICK VIL tSDS tSDH VIH SDTI VIL Audio Serial Interface Timing (PCM Mode) MS0203-E-00 2003/02 - 10 - ASAHI KASEI [AK4358] tDCK tDCKL tDCKH VIH DCLK VIL tDDD VIH DSDL DSDR VIL Audio Serial Interface Timing (DSD Normal Mode, DCKB = “0”) tDCK tDCKL tDCKH VIH DCLK VIL tDDD tDDD VIH DSDL DSDR VIL Audio Serial Interface Timing (DSD Phase Modulation Mode, DCKB = “0”) VIH CSN VIL tCSS tCCKL tCCKH VIH CCLK VIL tCDS CDTI C1 tCDH C0 R/W A4 VIH VIL WRITE Command Input Timing MS0203-E-00 2003/02 - 11 - ASAHI KASEI [AK4358] tCSW VIH CSN VIL tCSH VIH CCLK VIL CDTI D3 D2 D1 VIH D0 VIL WRITE Data Input Timing VIH SDA VIL tLOW tBUF tR tHIGH tF tSP VIH SCL VIL tHD:STA Stop Start tHD:DAT tSU:DAT tSU:STA tSU:STO Start Stop I2C Bus mode Timing tPD PDN VIL Power-down Timing MS0203-E-00 2003/02 - 12 - ASAHI KASEI [AK4358] OPERATION OVERVIEW D/A Conversion Mode The AK4358 can perform D/A conversion for both PCM data and DSD data. When DSD mode, DSD data can be input from DCLK, DSDL1-4 and DSDR1-4 pins. When PCM mode, PCM data can be input from BICK, SDTI1-4 and LRCK pins. PCM/DSD mode changes by D/P bit. When PCM/DSD mode changes by D/P bit, the AK4358 should be reset by RSTN bit, PW bit (PW1=PW2=PW3=PW4= “0”) or PDN pin. It takes about 2/fs to 3/fs to change the mode. D/P bit 0 1 DAC Output PCM DSD Table 1. DSD/PCM Mode Control System Clock 1) PCM Mode The external clocks, which are required to operate the AK4358, are MCLK, LRCK and BICK. The master clock (MCLK) should be synchronized with LRCK but the phase is not critical. The MCLK is used to operate the digital interpolation filter and the delta-sigma modulator. There are two methods to set MCLK frequency. In Manual Setting Mode (ACKS = “0”: Register 00H), the sampling speed is set by DFS0/1(Table 2). The frequency of MCLK at each sampling speed is set automatically. (Table 3~Table 5). In Auto Setting Mode (ACKS = “1”: Default), as MCLK frequency is detected automatically (Table 6), and the internal master clock becomes the appropriate frequency (Table 7), it is not necessary to set DFS0/1. When ACKSN = “H”, regardless of ACKS bit setting the AK4358 operates by Manual Setting Mode. When ACKSN = “L”, ACKS bit setting is valid. All external clocks (MCLK, BICK and LRCK) should always be present whenever the AK4358 is in the normal operation mode (PDN= ”H”). If these clocks are not provided, the AK4358 may draw excess current and may fall into unpredictable operation. This is because the device utilizes dynamic refreshed logic internally. The AK4358 should be reset by PDN = “L” after threse clocks are provided. If the external clocks are not present, the AK4358 should be in the power-down mode (PDN= ”L”). After exiting reset(PDN = “↑”) at power-up etc., the AK4358 is in the power-down mode until MCLK is input. DSD interface signals (DCLK, DSDL1-4, DSDR1-4) are fixed to “H” or “L”. DFS1 DFS0 Sampling Rate (fs) 0 0 Normal Speed Mode 0 1 Double Speed Mode 1 0 Quad Speed Mode 8kHz~48kHz Default 60kHz~96kHz 120kHz~192kHz Table 2. Sampling Speed (Manual Setting Mode) LRCK fs 32.0kHz 44.1kHz 48.0kHz 256fs 8.1920MHz 11.2896MHz 12.2880MHz MCLK 384fs 512fs 12.2880MHz 16.3840MHz 16.9344MHz 22.5792MHz 18.4320MHz 24.5760MHz 768fs 24.5760MHz 33.8688MHz 36.8640MHz BICK 64fs 2.0480MHz 2.8224MHz 3.0720MHz Table 3. System Clock Example (Normal Speed Mode @Manual Setting Mode) MS0203-E-00 2003/02 - 13 - ASAHI KASEI [AK4358] LRCK fs 88.2kHz 96.0kHz MCLK 192fs 256fs 16.9344MHz 22.5792MHz 18.4320MHz 24.5760MHz 128fs 11.2896MHz 12.2880MHz 384fs 33.8688MHz 36.8640MHz BICK 64fs 5.6448MHz 6.1440MHz Table 4. System Clock Example (Double Speed Mode @Manual Setting Mode) LRCK fs 176.4kHz 192.0kHz MCLK 128fs 192fs 22.5792MHz 33.8688MHz 24.5760MHz 36.8640MHz BICK 64fs 11.2896MHz 12.2880MHz Table 5. System Clock Example (Quad Speed Mode @Manual Setting Mode) MCLK 512fs 768fs 256fs 384fs 128fs 192fs Sampling Speed Normal Double Quad Table 6. Sampling Speed (Auto Setting Mode) LRCK fs 32.0kHz 44.1kHz 48.0kHz 88.2kHz 96.0kHz 176.4kHz 192.0kHz 128fs 22.5792 24.5760 192fs 33.8688 36.8640 MCLK (MHz) 256fs 384fs 22.5792 33.8688 24.5760 36.8640 - 512fs 16.3840 22.5792 24.5760 - 768fs 24.5760 33.8688 36.8640 - Sampling Speed Normal Double Quad Table 7. System Clock Example (Auto Setting Mode) ACKSN pin ACKS bit Clock Mode 0 0 Manual Setting Mode 0 1 Auto Setting Mode (Default) 1 0 Manual Setting Mode 1 1 Manual Setting Mode Table 8. Relationship between ACKSN pin and ACKS bit 2) DSD Mode The external clocks, which are required to operate the AK4358, are MCLK and DCLK. The master clock (MCLK) should be synchronized with DSD clock (DCLK) but the phase is not critical. The frequency of MCLK is set by DCKS bit. All external clocks (MCLK, DCLK) should always be present whenever the AK4358 is in the normal operation mode (PDN= ”H”). If these clocks are not provided, the AK4358 may draw excess current because the device utilizes dynamic refreshed logic internally. The AK4358 should be reset by PDN= ”L” after threse clocks are provided. If the external clocks are not present, the AK4358 should be in the power-down mode (PDN= ”L”). After exiting reset(PDN = “↑”) at power-up etc., the AK4358 is in the power-down mode until MCLK is input. PCM interface signals (BICK, LRCK, SDTI1-4) are fixed to “H” or “L”. MS0203-E-00 2003/02 - 14 - ASAHI KASEI [AK4358] DCKS MCLK DCLK 0 512fs 64fs 1 768fs 64fs Table 9. System Clock (fs=44.1kHz) Audio Serial Interface Format 1) PCM Mode When PCM mode, data is shifted in via the SDTI1-4 pins using BICK and LRCK inputs. The DIF0-2 as shown in Table 10 can select five serial data modes. Initial value of DIF0-2 bits is “010” and DIF0 bit is ORed with DIF0 pin. In all modes the serial data is MSB-first, 2’s compliment format and is latched on the rising edge of BICK. Mode 2 can be used for 16/20 MSB justified formats by zeroing the unused LSBs. When TDM0 = “1”, the audio interface becomes TDM mode. In TDM256 mode (TDM1 = “0”, Table 11), the serial data of all DAC (eight channels) is input to the SDTI1 pin. The input data to SDTI2-4 pins is ignored. BICK should be fixed to 256fs. “H” time and “L” time of LRCK should be 1/256fs at least. The serial data is MSB-first, 2’s compliment format. The input data to SDTI1 pin is latched on the rising edge of BICK. In TDM128 mode (TDM1 = “1”, Table 12), the serial data of DAC (four channels; L1, R1, L2, R2) is input to the SDTI1 pin. Other four data (L3, R3, L4, R4) is input to the SDTI2. The input data to SDTI3-4 pins is ignored. BICK should be fixed to 128fs. Mode 0 1 2 3 4 TDM1 0 0 0 0 0 TDM0 0 0 0 0 0 DIF2 0 0 0 0 1 DIF1 0 0 1 1 0 DIF0 0 1 0 1 0 SDTI Format 16bit LSB Justified 20bit LSB Justified 24bit MSB Justified 24bit I2S Compatible 24bit LSB Justified LRCK H/L H/L H/L L/H H/L BICK ≥32fs ≥40fs ≥48fs ≥48fs ≥48fs Figure Figure 1 Figure 2 Figure 3 Figure 4 Figure 2 13 15 Default Table 10. Audio Data Formats (Normal mode) LRCK 0 1 10 11 12 13 14 15 0 1 10 11 12 14 0 1 BICK (32fs) SDTI Mode 0 15 0 14 1 6 5 14 4 15 3 2 16 17 1 0 31 15 0 14 1 6 5 14 4 15 3 16 2 17 1 0 31 15 0 14 1 BICK (64fs) SDTI Mode 0 Don’t care 15 14 0 Don’t care 15 14 0 15:MSB, 0:LSB Lch Data Rch Data Figure 1. Mode 0 Timing MS0203-E-00 2003/02 - 15 - ASAHI KASEI [AK4358] LRCK 0 1 8 9 10 11 12 31 0 1 8 9 10 11 12 31 0 1 0 1 BICK (64fs) SDTI Mode 1 Don’t care 19 0 Don’t care 19 0 Don’t care 19 0 19 0 19:MSB, 0:LSB SDTI Mode 4 Don’t care 23 22 21 20 23 22 20 21 23:MSB, 0:LSB Lch Data Rch Data Figure 2. Mode 1,4 Timing LRCK 0 1 2 22 23 24 30 31 0 1 2 22 23 24 30 31 BICK (64fs) SDTI 23 22 1 0 Don’t care 23 22 0 1 Don’t care 23 22 0 1 23:MSB, 0:LSB Lch Data Rch Data Figure 3. Mode 2 Timing LRCK 0 1 2 3 23 24 25 31 0 1 2 3 23 24 25 31 BICK (64fs) SDTI 23 22 1 0 Don’t care 23 22 1 0 Don’t care 23 23:MSB, 0:LSB Lch Data Rch Data Figure 4. Mode 3 Timing MS0203-E-00 2003/02 - 16 - ASAHI KASEI Mode [AK4358] 5 TDM1 0 0 0 TDM0 1 1 1 DIF2 0 0 0 DIF1 0 0 1 DIF0 0 1 0 6 0 1 0 1 1 7 0 1 1 0 0 SDTI Format N/A N/A 24bit MSB Justified 24bit I2S Compatible 24bit LSB Justified LRCK BICK Figure ↑ 256fs Figure 5 ↓ 256fs Figure 6 ↑ 256fs Figure 7 Table 11. Audio Data Formats (TDM256 mode) 256 BICK LRCK BICK(256fs) SDTI1(i) 23 22 0 23 22 0 23 22 0 23 22 0 23 22 0 23 22 0 23 22 0 23 22 0 23 22 L1 R1 L2 R2 L3 R3 L4 R4 32 BICK 32 BICK 32 BICK 32 BICK 32 BICK 32 BICK 32 BICK 32 BICK Figure 5. Mode 5 Timing 256 BICK LRCK BICK(256fs) SDTI1(i) 23 0 23 0 23 0 23 0 23 0 23 0 23 0 23 0 L1 R1 L2 R2 L3 R3 L4 R4 32 BICK 32 BICK 32 BICK 32 BICK 32 BICK 32 BICK 32 BICK 32 BICK 23 Figure 6. Mode 6 Timing 256 BICK LRCK BICK(256fs) SDTI1(i) 23 22 0 23 22 0 23 22 0 23 22 0 23 22 0 23 22 0 23 22 0 23 22 L1 R1 L2 R2 L3 R3 L4 R4 32 BICK 32 BICK 32 BICK 32 BICK 32 BICK 32 BICK 32 BICK 32 BICK 0 23 Figure 7. Mode 7 Timing MS0203-E-00 2003/02 - 17 - ASAHI KASEI Mode [AK4358] 8 TDM1 1 1 1 TDM0 1 1 1 DIF2 0 0 0 DIF1 0 0 1 DIF0 0 1 0 9 1 1 0 1 1 10 1 1 1 0 0 SDTI Format N/A N/A 24bit MSB Justified 24bit I2S Compatible LRCK BICK Figure ↑ 128fs Figure 8 ↓ 128fs Figure 9 24bit LSB Justified ↑ 128fs Figure 10 Table 12. Audio Data Formats (TDM128 mode) 128 BICK LRCK BICK(128fs) SDTI1(i) SDTI2(i) 23 22 23 22 0 0 23 22 23 22 0 L1 R1 L2 R2 32 BICK 32 BICK 32 BICK 32 BICK 23 22 23 22 0 0 23 22 23 22 0 L3 R3 L4 R4 32 BICK 32 BICK 32 BICK 32 BICK 0 23 22 0 23 22 0 23 0 23 Figure 8. Mode 8 Timing 128 BICK LRCK BICK(128fs) SDTI1(i) SDTI2(i) 23 22 0 23 22 0 0 23 22 23 22 L1 R1 L2 R2 32 BICK 32 BICK 32 BICK 32 BICK 23 22 0 23 22 0 0 23 22 23 22 L3 R3 L4 R4 32 BICK 32 BICK 32 BICK 32 BICK Figure 9. Mode 9 Timing 128 BICK LRCK BICK(128fs) SDTI1(i) SDTI2(i) 23 22 0 23 22 0 23 22 0 23 22 L1 R1 L2 R2 32 BICK 32 BICK 32 BICK 32 BICK 23 22 0 23 22 0 23 22 0 23 22 L3 R3 L4 R4 32 BICK 32 BICK 32 BICK 32 BICK 0 19 0 19 Figure 10. Mode 10 Timing MS0203-E-00 2003/02 - 18 - ASAHI KASEI [AK4358] 2) DSD Mode In case of DSD mode, DIF0-2 is ignored. The frequency of DCLK is fixed to 64fs. DCKB bit can invert the polarity of DCLK. DCLK (64fs) DCKB=1 DCLK (64fs) DCKB=0 DSDL,DSDR Normal D0 DSDL,DSDR Phase Modulation D0 D1 D1 D2 D1 D2 D3 D3 D2 Figure 11. DSD Mode Timing D/A conversion mode switching timing RSTN bit ≥4/fs D/A Mode PCM Mode DSD Mode ≥0 D/A Data PCM Data DSD Data Figure 12. D/A Mode Switching Timing (PCM to DSD) RSTN bit D/A Mode DSD Mode PCM Mode ≥4/fs D/A Data DSD Data PCM Data Figure 13. D/A Mode Switching Mode Timing (DSD to PCM) Caution: In DSD mode, the signal level is ranging from 25% to 75%. Peak levels of DSD signal above this duty are not recommended by SACD format book (Scarlet Book). MS0203-E-00 2003/02 - 19 - ASAHI KASEI [AK4358] De-emphasis Filter A digital de-emphasis filter is available for 32, 44.1 or 48kHz sampling rates (tc = 50/15µs) and is enabled or disabled with DEM0 and DEM1. In case of double speed and quad speed mode, the digital de-emphasis filter is always off. When DSD mode, DEM0-1 is invalid. DEM1 DEM0 Mode 0 0 1 1 0 1 0 1 44.1kHz OFF 48kHz 32kHz Default Table 13. De-emphasis Filter Control (Normal Speed Mode) Output Volume The AK4358 includes channel independent digital output volumes (ATT) with 128 levels at 0.5dB steps including SMUTE. These volumes are in front of the DAC and can attenuate the input data from 0dB to –63dB and mute. Transition time is set by AST1-0 bits(Table 15) When changing levels, transitions are executed via soft changes; thus no switching noise occurs during these transitions. When ATTE bit is set to “0”, the DAC input data goes to “0” immediately. It takes a time of group delay to mute the analog output. ATTE bit should be “1” to enable the volume setting. ATTE 1 0 ATT6-0 7FH 7EH 7DH : 02H 01H 00H Don’t care Attenuation Level 0dB -0.5dB -1.0dB : -62.5dB -63.0dB SMUTE (-∞) OFF ( “0” ) Default Table 14. Attenuation Level of Output Volume Mode 0 1 2 3 ATS1 0 0 1 1 ATS0 0 1 0 1 ATT speed 1792/fs 896/fs 256/fs N/A Default Table 15. Transition time of output volume In case of Mode 0, it takes 1792/fs to transit from 7FH(0dB) to 00H(SMUTE). In case Mode1, it takes 896/fs to transit from 7FH(0dB) to 00H(SMUTE). In case Mode2 and 3,it takes 256/fs to transit from 7FH(0dB) to 00H (SMUTE). If PDN pin goes to “L”, ATT6-0 registers are initialized to 7FH.ATT6-0 registers go to 7FH when RSTN bit is set to “0”. When RSTN bit returns to “1”, ATT6-0 registers go to the set value. Digital output volume function is independent of soft mute function. The setting value of the register is held when switching between PCM mode and DSD mode. MS0203-E-00 2003/02 - 20 - ASAHI KASEI [AK4358] Zero Detection When the input data at all channels are continuously zeros for 8192 LRCK cycles, the AK4358 has Zero Detection like Table 16. DZF pin immediately goes to “L” if input data of each channel is not zero after going DZF “H”. If RSTN bit is “0”, DZF pin goes to “H”. DZF pin goes to “L” at 4~5LRCK if input data of each channel is not zero after RSTN bit returns to “1”. Zero detect function can be disabled by DZFE bit. In this case, all DZF pins are always “L”. When one of PW1-4 bit is set to “0”, the input data of DAC that the PW bit is set to “0” should be zero in order to enable zero detection of the other channels. When all PW1-4 bits are set to “0”, DZF pin fixes “L”. DZFB bit can invert the polarity of DZF pin. DZF Pin DZF1 DZF2 DZF3 Operations ANDed output of zero detection flag of each channel set to “1” in 0DH register ANDed output of zero detection flag of each channel set to “1” in 0EH register ANDed output of zero detection flag of each channel set to “1” in 0FH register Table 16. DZF pins Operation Soft Mute Operation Soft mute operation is performed at digital domain. When the SMUTE bit goes to “1”, the output signal is attenuated by -∞ during ATT_DATA×ATT transition time (Table 15) from the current ATT level. When the SMUTE bit is returned to “0”, the mute is cancelled and the output attenuation gradually changes to the ATT level during ATT_DATA×ATT transition time. If the soft mute is cancelled before attenuating to -∞ after starting the operation, the attenuation is discontinued and returned to ATT level by the same cycle. The soft mute is effective for changing the signal source without stopping the signal transmission. SMUTE bit ATT Level (1) (1) (3) Attenuation -∞ GD (2) GD AOUT DZF pin (4) 8192/fs Notes: (1) ATT_DATA×ATT transition time (Table 15). For example, in Normal Speed Mode, this time is 1792LRCK cycles (1792/fs) at ATT_DATA=128. (2) The analog output corresponding to the digital input has a group delay, GD. (3) If the soft mute is cancelled before attenuating to -∞ after starting the operation, the attenuation is discontinued and returned to ATT level by the same cycle. (4) When the input data at each channel is continuously zeros for 8192 LRCK cycles, DZF pin of each channel goes to “H”. DZF pin immediately goes to “L” if input data are not zero after going DZF “H”. Figure 14. Soft Mute and Zero Detection MS0203-E-00 2003/02 - 21 - ASAHI KASEI [AK4358] System Reset The AK4358 should be reset once by bringing PDN= ”L” upon power-up. The analog section exits power-down mode by MCLK input and then the digital section exits power-down mode after the internal counter counts MCLK during 4/fs. Power-down The AK4358 is placed in the power-down mode by bringing PDN pin “L” and the anlog outputs are floating (Hi-Z). Figure 6 shows an example of the system timing at the power-down and power-up. Each DAC can be powered down by each power-down bit (PW1-3) “0”. In this case, the internal register values are not initialized and the analog output is Hi-Z. Because some click noise occurs, the analog output should be muted externally if the click noise influences system application. PDN Internal State Normal Operation Power-down D/A In (Digital) Normal Operation “0” data GD D/A Out (Analog) (1) GD (2) (3) (3) (1) (4) Clock In Don’t care MCLK, LRCK, BICK DZF External MUTE (6) (5) Mute ON Notes: (1) The analog output corresponding to digital input has the group delay (GD). (2) Analog outputs are floating (Hi -Z) at the power-down mode. (3) Click noise occurs at the edge of PDN signal. This noise is output even if “0” data is input. (4) The external clocks (MCLK, BICK and LRCK) can be stopped in the power-down mode (PDN = “L”). (5) Please mute the analog output externally if the click noise (3) influence system application. The timing example is shown in this figure. (6) DZF pins are “L” in the power-down mode (PDN = “L”). Figure 15. Power-down/up Sequence Example MS0203-E-00 2003/02 - 22 - ASAHI KASEI [AK4358] Reset Function When RSTN=0, DAC is powered down but the internal register values are not initialized. The analog outputs go to VCOM voltage and DZFL/DZFR pins go to “H”. Figure 16 shows the example of reset by RSTN bit. RSTN bit 3~4/fs (6) 2~3/fs (6) Internal RSTN bit Internal State Normal Operation D/A In (Digital) “0” data (1) D/A Out (Analog) Normal Operation Digital Block Power-down GD GD (2) (3) (3) (1) (4) Clock In Don’t care MCLK,LRCK,BICK 2/fs(5) DZF Notes: (1) The analog output corresponding to digital input has the group delay (GD). (2) Analog outputs go to VCOM voltage. (3) Click noise occurs at the edges(“↑ ↓”) of the internal timing of RSTN bit. This noise is output even if “0” data is input. (4) The external clocks (MCLK, BICK and LRCK) can be stopped in the reset mode (RSTN = “L”). (5) DZF pins go to “H” when the RSTN bit becomes “0”, and go to “L” at 2/fs after RSTN bit becomes “1”. (6) There is a delay, 3~4/fs from RSTN bit “0” to the internal RSTN bit “0”, and 2~3/fs from RSTN bit “1” to the internal RSTN “1”. Figure 16. Reset Sequence Example MS0203-E-00 2003/02 - 23 - ASAHI KASEI [AK4358] Register Control Interface The AK4358 controls its functions via registers. 2 types of control mode write internal registers. In the I2C-bus mode, the chip address is determined by the state of the CAD0 and CAD1 inputs. In 3-wire mode, the CAD1 input is fixed to “1” and Chip Address C0 is determined by the state of the CAD0 pin. PDN = “L” initializes the registers to their default values. Writing “0” to the RSTN bit resets the internal timing circuit, but the register data is not initialized. * The AK4358 does not support the read command. * When the AK4358 is in the power down mode (PDN = “L”) or the MCLK is not provided, Writing to control register is invalid. Function Manual Setting Mode De-emphasis DZFE SMUTE Audio data format DSD mode Attenuator Slow roll-off response Pin set-up O X X X DIF0 X X X Register set-up O O O O O O O O Table 17. Function Table (O: Supported, X: Not supported) (1) 3-wire Serial Control Mode (I2C = “L”) 3-wire µP interface pins, CSN, CCLK and CDTI, write internal registers. The data on this interface consists of Chip Address (2bits, C1/0; C1 is fixed to “1” and C0=CAD0), Read/Write (1bit; fixed to “1”, Write only), Register Address (MSB first, 5bits) and Control Data (MSB first, 8bits). The AK4358 latches the data on the rising edge of CCLK, so data should clocked in on the falling edge. The writing of data becomes valid by the rising edge of CSN. The clock speed of CCLK is 5MHz (max). CSN 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 CCLK CDTI C1 C0 R/W A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 C1-C0: R/W: A4-A0: D7-D0: Chip Address (C1= “1”, C0=CAD0) READ/WRITE (Fixed to “1”, Write only) Register Address Control Data Figure 17. Control I/F Timing MS0203-E-00 2003/02 - 24 - ASAHI KASEI [AK4358] (2) I2C-bus Control Mode (I2C= “H”) The AK4358 supports the standard-mode I2C-bus (max:100kHz). Then the AK4358 does not support a fast-mode I2C-bus system (max: 400kHz). Figure 18 shows the data transfer sequence at the I2C-bus mode. All commands are preceded by a START condition. A HIGH to LOW transition on the SDA line while SCL is HIGH indicates a START condition (Figure 22). After the START condition, a slave address is sent. This address is 7 bits long followed by an eighth bit which is a data direction bit (R/W) (Figure 19). The most significant five bits of the slave address are fixed as “00100”. The next two bits are CAD1 and CAD0 (device address bits). These two bits identify the specific device on the bus. The hard-wired input pins (CAD1 pin and CAD0 pin) set them. If the slave address match that of the AK4358 and R/W bit is “0”, the AK4358 generates the acknowledge and the write operation is executed. If R/W bit is “1”, the AK4358 generates the not acknowledge since the AK4358 can be only a slave-receiver. The master must generate the acknowledge-related clock pulse and release the SDA line (HIGH) during the acknowledge clock pulse (Figure 23). The second byte consists of the address for control registers of the AK4358. The format is MSB first, and those most significant 3-bits are fixed to zeros (Figure 20). Those data after the second byte contain control data. The format is MSB first, 8bits (Figure 21). The AK4358 generates an acknowledge after each byte has been received. A data transfer is always terminated by a STOP condition generated by the master. A LOW to HIGH transition on the SDA line while SCL is HIGH defines a STOP condition (Figure 22). The AK4358 is capable of more than one byte write operation by one sequence. After receipt of the third byte, the AK4358 generates an acknowledge, and awaits the next data again. The master can transmit more than one byte instead of terminating the write cycle after the first data byte is transferred. After the receipt of each data, the internal 5bits address counter is incremented by one, and the next data is taken into next address automatically. If the addresses exceed 1FH prior to generating the stop condition, the address counter will “roll over” to 00H and the previous data will be overwritten. The data on the SDA line must be stable during the HIGH period of the clock. The HIGH or LOW state of the data line can only change when the clock signal on the SCL line is LOW (Figure 24) except for the START and the STOP condition. S T A R T SDA S S T O P R/W Slave Address Sub Address(n) A C K Data(n+x) Data(n+1) Data(n) A C K A C K A C K A C K P A C K Figure 18. Data transfer sequence at the I2C-bus mode 0 0 1 0 0 CAD1 CAD0 R/W (Those CAD1/0 should match with CAD1/0 pins) Figure 19. The first byte 0 0 0 A4 A3 A2 A1 A0 D2 D1 D0 Figure 20. The second byte D7 D6 D5 D4 D3 Figure 21. Byte structure after the second byte MS0203-E-00 2003/02 - 25 - ASAHI KASEI [AK4358] SDA SCL S P start condition stop condition Figure 22. START and STOP conditions DATA OUTPUT BY MASTER not acknowledge DATA OUTPUT BY SLAVE(AK4529) acknowledge SCL FROM MASTER 2 1 8 9 S clock pulse for acknowledgement START CONDITION Figure 23. Acknowledge on the I2C-bus SDA SCL data line stable; data valid change of data allowed Figure 24. Bit transfer on the I2C-bus MS0203-E-00 2003/02 - 26 - ASAHI KASEI [AK4358] Register Map Addr 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0FH Register Name Control 1 Control 2 Speed & Power Down Control De-emphasis Control LOUT1 ATT Control ROUT1 ATT Control LOUT2 ATT Control ROUT2 ATT Control LOUT3 ATT Control ROUT3 ATT Control Control 3 LOUT4 ATT Control ROUT4 ATT Control DZF1 Control DZF2 Control DZF3 Control D7 ACKS 0 0 0 ATTE ATTE ATTE ATTE ATTE ATTE TDM1 ATTE ATTE L1 L1 L1 D6 SLOW 0 PW4 0 ATT6 ATT6 ATT6 ATT6 ATT6 ATT6 TDM0 ATT6 ATT6 R1 R1 R1 D5 0 0 DFS1 D4 DZFE 0 DFS0 D3 DIF2 0 PW3 D2 DIF1 0 PW2 D1 DIF0 0 0 0 0 DEM1 DEM0 ATT5 ATT5 ATT5 ATT5 ATT5 ATT5 DCKS ATT5 ATT5 L2 L2 L2 ATT4 ATT4 ATT4 ATT4 ATT4 ATT4 D/P ATT4 ATT4 R2 R2 R2 ATT3 ATT3 ATT3 ATT3 ATT3 ATT3 DCKB ATT3 ATT3 L3 L3 L3 ATT2 ATT2 ATT2 ATT2 ATT2 ATT2 DZFB ATT2 ATT2 R3 R3 R3 ATT1 ATT1 ATT1 ATT1 ATT1 ATT1 ATS1 ATT1 ATT1 L4 L4 L4 ATT0 ATT0 ATT0 ATT0 ATT0 ATT0 ATS0 ATT0 ATT0 R4 R4 R4 SMUTE PW1 D0 RSTN RSTN RSTN Note: For addresses from 10H to 1FH, data must not be written. When PDN goes to “L”, the registers are initialized to their default values. When RSTN bit goes to “0”, the only internal timing is reset, and the registers are not initialized to their default values. All data can be written to the registers even if PW1-4 or RSTN bit is “0”. ACKS bit is ANDed with the ACKSN pin. DIF0 bit is ORed with the DIF pin. MS0203-E-00 2003/02 - 27 - ASAHI KASEI [AK4358] Register Definitions Addr 00H Register Name Control 1 Default D7 ACKS 1 D6 SLOW 0 D5 0 0 D4 DZFE 1 D3 DIF2 0 D2 DIF1 1 D1 DIF0 0 D0 RSTN 1 RSTN: Internal timing reset 0: Reset. All DZF pins go to “H” and any registers are not initialized. 1: Normal operation When MCLK frequency or DFS changes, the AK4358 should be reset by PDN pin or RSTN bit. DIF2-0: Audio data interface modes (See Table 10, Table 11, Table 12, PCM Only) Initial: “010” Register bit of DIF0 is ORed with the DIF0 pin. DZFE: Data Zero Detect Enable 0: Disable 1: Enable Zero detect function can be disabled by DZFE bit “0”. In this case, the DZF pins are “L” at DZFB bit “0” and are “H” at DZFB bit “1”. SLOW: Slow Roll-off Filter Enable (PCM Only) 0: Sharp Roll-off Filter 1: Slow Roll-off Filter ACKS: Master Clock Frequency Auto Setting Mode Enable 0: Disable, Manual Setting Mode 1: Enable, Auto Setting Mode Master clock frequency is detected automatically at ACKS bit “1”. In this case, the setting of DFS1-0 is ignored. When this bit is “0”, DFS1-0 set the sampling speed mode. Register bit of ACKS is ANDed with the inverted of the ACKSN pin. Addr 01H Register Name Control 2 Default D7 D6 D5 D4 D3 D2 D1 D0 RSTN 1 0 0 0 0 0 0 SMUT E 0 0 0 0 0 0 0 RSTN: Internal timing reset 0: Reset. All DZF pins of go to “H” and any registers are not initialized. 1: Normal operation When MCLK frequency or DFS changes, the AK4358 should be reset by PDN pin or RSTN bit. SMUTE: Soft Mute Enable 0: Normal operation 1: All DAC outputs soft-muted MS0203-E-00 2003/02 - 28 - ASAHI KASEI Addr 02H [AK4358] Register Name Speed & Power Down Control Default D7 0 0 D6 PW4 1 D5 DFS1 0 D4 DFS0 0 D3 PW3 1 D2 PW2 1 D1 PW1 1 D0 RSTN 1 RSTN: Internal timing reset 0: Reset. All DZF pins go to “H” and any registers are not initialized. 1: Normal operation When MCLK frequency or DFS changes, the AK4358 should be reset by PDN pin or RSTN bit. PW4-1: Power-down control (0: Power-down, 1: Power-up) PW1: Power down control of DAC1 PW2: Power down control of DAC2 PW3: Power down control of DAC3 PW4: Power down control of DAC4 All sections are powered-down by PW1=PW2=PW3=PW4=0. DFS1-0: Sampling speed control (See Table 2, PCM Only) 00: Normal speed 01: Double speed 10: Quad speed When changing between Normal/Double Speed Mode and Quad Speed Mode, some click noise occurs. Addr 03H Register Name De-emphasis Control Default D7 0 0 D6 0 0 D5 D4 D3 D2 D1 D0 0 0 0 0 DEM1 DEM0 0 0 0 0 0 1 DEM1-0: De-emphasis response control for DAC1/2/3/4 data on SDTI1/2/3/4 (See Table 13, PCM only) Initial: “01”, OFF Addr 04H 05H 06H 07H 08H 09H 0BH 0CH Register Name LOUT1 ATT Control ROUT1 ATT Control LOUT2 ATT Control ROUT2 ATT Control LOUT3 ATT Control ROUT3 ATT Control LOUT4 ATT Control ROUT4 ATT Control Default D7 ATTE ATTE ATTE ATTE ATTE ATTE ATTE ATTE 1 D6 ATT6 ATT6 ATT6 ATT6 ATT6 ATT6 ATT6 ATT6 1 D5 ATT5 ATT5 ATT5 ATT5 ATT5 ATT5 ATT5 ATT5 1 D4 ATT4 ATT4 ATT4 ATT4 ATT4 ATT4 ATT4 ATT4 1 D3 ATT3 ATT3 ATT3 ATT3 ATT3 ATT3 ATT3 ATT3 1 D2 ATT2 ATT2 ATT2 ATT2 ATT2 ATT2 ATT2 ATT2 1 D1 ATT1 ATT1 ATT1 ATT1 ATT1 ATT1 ATT1 ATT1 1 D0 ATT0 ATT0 ATT0 ATT0 ATT0 ATT0 ATT0 ATT0 1 ATT6-0: Attenuation Level 128 levels, 0.5dB step (See Table 14) ATTE: Attenuation Output Enable 0: Disable 1: Enable MS0203-E-00 2003/02 - 29 - ASAHI KASEI Addr 0AH [AK4358] Register Name Control 3 Default D7 TDM1 0 D6 TDM0 0 D5 DCKS 0 D4 D/P 0 D3 DCKB 0 D2 DZFB 0 D1 ATS1 0 D0 ATS0 0 ATS1-0: DATT Speed Setting (See Table 15) Initial: “00”, mode 0 DZFB: Inverting Enable of DZF 0: DZF goes “H” at Zero Detection 1: DZF goes “L” at Zero Detection DCKB: Polarity of DCLK (DSD Only) 0: DSD data is output from DCLK falling edge 1: DSD data is output from DCLK rising edge D/P: DSD/PCM Mode Select 0: PCM Mode. SCLK, SDTI1-4, LRCK 1: DSD Mode. DCLK, DSDL1-4, DSDR1-4 When D/P changes form “1” to “0”, the AK4358 should be reset by PDN pin, PW bit or RSTN bit. When D/P changes form “0” to “1”, the AK4358 should be reset by PW bit or RSTN bit. DCKS: Master Clock Frequency Select at DSD mode (DSD only) 0: 512fs 1: 768fs TDM0-1: TDM Mode Select (PCM only) Mode Normal TDM256 TDM128 Addr 0DH Register Name DZF1 Control Default TDM1 0 0 1 TDM0 0 1 1 D7 L1 1 BICK 32fs∼ 256fs fixed 128fs fixed D6 R1 1 SDTI 1-4 1 1-2 D5 L2 1 Sampling Speed Normal, Double, Quad Speed Normal Speed Normal, Double Speed D4 R2 1 D3 L3 1 D2 R3 1 D1 L4 1 D0 R4 1 D4 R2 R2 0 D3 L3 L3 0 D2 R3 R3 0 D1 L4 L4 0 D0 R4 R4 0 L1-4, R1-4: Zero Detect Flag Enable Bit for DZF1 pin 0: Disable 1: Enable Addr 0EH 0FH Register Name DZF2 Control DZF3 Control Default D7 L1 L1 0 D6 R1 R1 0 D5 L2 L2 0 L1-4, R1-4: Zero Detect Flag Enable Bit for DZF2,3 pins 0: Disable 1: Enable MS0203-E-00 2003/02 - 30 - ASAHI KASEI [AK4358] SYSTEM DESIGN Figure 25 shows the system connection diagram. An evaluation board (AKD4358) is available which demonstrates application circuits, the optimum layout, power supply arrangements and measurement results. + 10u Digital 5V 0.1u Reset 3 2 DZF3 LOUT1+ 1 4 DZF2 LOUT1- 5 DZF1 7 6 PDN CAD1 8 9 BICK ROUT1- 47 15 SDTI2 LOUT2+ 46 16 SDTI3 LOUT2- 45 AK4358 ROUT2- 43 19 CCLK/SCL LOUT3- 41 35 AVDD 34 VREFH 33 ROUT4+ 32 ROUT4- 25 31 DIF0 DSDL1 Data 30 DSDR3 LOUT4+ 38 29 DSDL3 23 DSDL4 28 DSDR2 ROUT3- 39 27 DSDL2 ROUT3+ 40 22 DCLK 26 DSDR1 21 CSN/CAD1 DSD LPF MUTE R1ch OUT LPF MUTE L2ch OUT LPF MUTE R2ch OUT LPF MUTE L3ch OUT LPF MUTE R3ch OUT LPF MUTE L4ch OUT LOUT3+ 42 Top View 20 CDTI/SDA DSDR4 L1ch OUT ROUT2+ 44 18 I2C 24 MUTE 48 14 SDTI1 17 LRCK uP ROUT1+ LPF LOUT4- 37 36 AVSS DSP CAD0 13 SDTI4 MCLK 10 DVSS 12 Gen DVDD 11 Clock Controller Analog 5V + 0.1u 10u Mode Control LPF System Ground MUTE R4ch OUT Analog Ground Figure 25. Typical Connection Diagram Notes: - LRCK = fs, BICK = 64fs. - When AOUT drives some capacitive load, some resistor should be added in series between AOUT and capacitive load. - All input pins except pull-down pins should not be left floating. MS0203-E-00 2003/02 - 31 - ASAHI KASEI [AK4358] 4 3 2 DZF2 DZF3 LOUT1+ ROUT1- 47 15 SDTI2 LOUT2+ 46 16 SDTI3 LOUT2- 45 17 LRCK ROUT2+ 44 AK4358 18 I2C ROUT2- 43 19 CCLK/SCL LOUT3+ 42 20 CDTI/SDA LOUT3- 41 21 CSN/CAD1 ROUT3+ 40 36 AVSS 35 AVDD 34 VREFH 33 ROUT4+ 32 ROUT4- 31 DIF0 37 28 DSDR2 38 LOUT4- 24 DSDR4 27 DSDL2 39 25 DSDL1 ROUT3LOUT4+ 26 DSDR1 22 DCLK 23 DSDL4 30 DSDR3 Controller ROUT1+ 48 14 SDTI1 29 DSDL3 System 1 5 DZF1 13 SDTI4 LOUT1- 7 6 CAD0 8 PDN CAD1 9 BICK MCLK 10 DVSS 12 Analog Ground DVDD 11 Digital Ground Figure 26. Ground Layout AVSS and DVSS must be connected to the same analog ground plane. 1. Grounding and Power Supply Decoupling AVDD and DVDD are usually supplied from analog supply in system and should be separated from system digital supply. Alternatively if AVDD and DVDD are supplied separately, the power up sequence is not critical. AVSS and DVSS of the AK4358 must be connected to analog ground plane. System analog ground and digital ground should be connected together near to where the supplies are brought onto the printed circuit board. Decoupling capacitor, especially 0.1µF ceramic capacitor for high frequency should be placed as near to AVDD and DVDD as possible. 2. Voltage Reference VREFH sets the analog output range. VREFH pin is normally connected to AVDD with a 0.1µF ceramic capacitor. All signals, especially clocks, should be kept away from the VREFH pin in order to avoid unwanted coupling into the AK4358. 3. Analog Outputs The analog outputs are full-differential outputs and 0.5 x VREFH Vpp (typ) centered around the internal common voltage (about AVDD/2). The differential outputs are summed externally, VAOUT=(AOUT+)-(AOUT-) between AOUT+ and AOUT-. If the summing gain is 1, the output range is 5.0Vpp (typ @VREFH=5V). The bias voltage of the external summing circuit is supplied externally. The input data format is 2’s complement. The output voltage(VAOUT) is a positive full scale for 7FFFFF (@24bit) and a negative full scale for 800000H (@24bit). The ideal VAOUT is 0V for 000000H (@24bit). The internal switched-capacitor filter and external low pass filter attenuate the noise generated by the delta-sigma modulator beyond the audio passband. DC offset on AOUT+/- is eliminated without AC coupling since the analog outputs are differential. MS0203-E-00 2003/02 - 32 - ASAHI KASEI [AK4358] 4. External Analog Filter It is recommended by SACD format book (Scarlet Book) that the filter response at SACD playback is an analog low pass filter with a cut-off frequency of maximum 50kHz and a slop of minimum 30dB/Oct. The AK4358 can achieve this filter response by combination of the internal filter (Table 18) and an external filter (Figure 27). Frequency 20kHz 50kHz 100kHz Gain -0.4dB -2.8dB -15.5dB Table 18. Internal Filter Response at DSD mode 2.0k AOUT- 1.8k 4.3k 1.0k 2.5Vpp 2200p 270p +Vop 3300p 2.0k 1.8k 1.0k AOUT+ - Analog Out + 4.3k 2.5Vpp 270p 5.65Vpp -Vop Figure 27. External 3rd order LPF Circuit Example Frequency Gain 20kHz -0.05dB 50kHz -0.51dB 100kHz -16.8dB DC gain = 1.07dB Table 19. 3rd order LPF (Figure 27) Response 3.9k AOUT- 4.7k R1 2.5Vpp 470p +Vop 3900p 3.9k AOUT+ 2.5Vpp Analog Out R1 4.7k 470p 6.05Vpp -Vop When R1=180Ω fc=90.1kHz, Q=0.735, g=-0.04dB at 40kHz When R1=150Ω fc=99.0kHz, Q=0.680, g=-0.23dB at 40kHz Figure 28. External 2nd order LPF Circuit Example for PCM MS0203-E-00 2003/02 - 33 - ASAHI KASEI [AK4358] PACKAGE 48pin LQFP(Unit:mm) 1.70Max 9.0 ± 0.2 0.13 ± 0.13 7.0 36 25 24 48 13 7.0 37 1 9.0 ± 0.2 1.40 ± 0.05 12 0.16 ± 0.07 0.5 0.22 ± 0.08 0.10 M 0° ∼ 10° 0.10 0.5 ± 0.2 Package & Lead frame material Package molding compound: Lead frame material: Lead frame surface treatment: Epoxy Cu Solder (Pb free) plate MS0203-E-00 2003/02 - 34 - ASAHI KASEI [AK4358] MARKING AKM AK4358VQ XXXXXXX 1 1) Asahi Kasei Logo 2) Marking Code: AK4358VQ 3) Date Code: XXXXXXX(7 digits) 4) Pin #1 indication IMPORTANT NOTICE • These products and their specifications are subject to change without notice. Before considering any use or application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM) sales office or authorized distributor concerning their current status. • AKM assumes no liability for infringement of any patent, intellectual property, or other right in the application or use of any information contained herein. • Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. • AKM products are neither intended nor authorized for use as critical components in any safety, life support, or other hazard related device or system, and AKM assumes no responsibility relating to any such use, except with the express written consent of the Representative Director of AKM. As used here: (a) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. (b) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. • It is the responsibility of the buyer or distributor of an AKM product who distributes, disposes of, or otherwise places the product with a third party to notify that party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification. MS0203-E-00 2003/02 - 35 -