GS71116ATP/J/U SOJ, TSOP, FP-BGA Commercial Temp Industrial Temp 7, 8, 10, 12 ns 3.3 V VDD Center VDD and VSS 64K x 16 1Mb Asynchronous SRAM Features • Fast access time: 7, 8, 10, 12 ns • CMOS low power operation: 145/125/100/85 mA at minimum cycle time • Single 3.3 V power supply • All inputs and outputs are TTL-compatible • Byte control • Fully static operation • Industrial Temperature Option: –40° to 85°C • Package line up J: 400 mil, 44-pin SOJ package TP: 400 mil, 44-pin TSOP Type II package GP: Pb-Free 400 mil, 3244-pin TSOP Type II package U: 6 mm x 8 mm Fine Pitch Ball Grid Array package GU: Pb-Free 6 mm x 8 mm Fine Pitch Ball Grid Array package • Pb-Free TSOP-II and FP-BGA packages available Description The GS71116A is a high speed CMOS static RAM organized as 65,536-words by 16-bits. Static design eliminates the need for external clocks or timing strobes. Operating on a single 3.3 V power supply and all inputs and outputs are TTLcompatible. The GS71116A is available in a 6 mm x 8 mm Fine Pitch BGA package, as well as in 400 mil SOJ and 400 mil TSOP Type-II packages. Pin Descriptions Symbol Description A0–A15 Address input DQ1–DQ16 Data input/output CE Chip enable input LB Lower byte enable input (DQ1 to DQ8) UB Upper byte enable input (DQ9 to DQ16) WE Write enable input OE Output enable input VDD +3.3 V power supply VSS Ground NC No connect Rev: 1.07 12/2004 SOJ 64K x 16-Pin Configuration A4 A3 A2 A1 A0 CE DQ1 DQ2 DQ3 DQ4 VDD VSS DQ5 DQ6 DQ7 DQ8 WE A15 A14 A13 A12 NC 1 2 3 4 5 6 7 8 9 10 11 12 Top view 44-pin SOJ 13 14 15 16 17 18 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 19 20 21 22 A5 A6 A7 OE UB LB DQ16 DQ15 DQ14 DQ13 VSS VDD DQ12 DQ11 DQ10 DQ9 NC A8 A9 A10 A11 NC Package J 1/16 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. © 2001, GSI Technology GS71116ATP/J/U Fine Pitch BGA 64K x 16-Bump Configuration 1 2 3 4 5 6 A LB OE A0 A1 A2 NC B DQ16 UB A3 A4 CE DQ1 C DQ14 DQ15 A5 A6 DQ2 DQ3 D VSS DQ13 NC A7 DQ4 VDD E VDD DQ12 NC NC DQ5 VSS F DQ11 DQ10 A8 A9 DQ7 DQ6 G DQ9 NC A10 A11 WE DQ8 H NC A12 A13 A14 A15 NC 6 mm x 8 mm, 0.75 mm Bump Pitch (Package U) Top View TSOP-II 64K x 16-Pin Configuration A4 A3 A2 A1 A0 CE DQ1 DQ2 DQ3 DQ4 VDD VSS DQ5 DQ6 DQ7 DQ8 WE A15 A14 A13 A12 NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Top view 44-pin TSOP II 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 16 17 18 19 20 21 22 A5 A6 A7 OE UB LB DQ16 DQ15 DQ14 DQ13 VSS VDD DQ12 DQ11 DQ10 DQ9 NC A8 A9 A10 A11 NC Package TP Rev: 1.07 12/2004 2/16 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. © 2001, GSI Technology GS71116ATP/J/U Block Diagram A0 Address Input Buffer Row Decoder Memory Array Column Decoder A15 CE WE Control OE UB _____ I/O Buffer DQ1 DQ16 Truth Table CE OE WE LB UB DQ1 to DQ8 DQ9 to DQ16 VDD Current H X X X X Not Selected Not Selected ISB1, ISB2 L L Read Read L H Read High Z H L High Z Read L L Write Write L H Write Not Write, High Z H L Not Write, High Z Write L L L X H L L H H X X High Z High Z L X X H H High Z High Z IDD Note: X: “H” or “L” Rev: 1.07 12/2004 3/16 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. © 2001, GSI Technology GS71116ATP/J/U Absolute Maximum Ratings Parameter Symbol Rating Unit Supply Voltage VDD –0.5 to +4.6 V Input Voltage VIN –0.5 to VDD +0.5 (≤ 4.6 V max.) V Output Voltage VOUT –0.5 to VDD +0.5 (≤ 4.6 V max.) V Allowable power dissipation PD 0.7 W Storage temperature TSTG –55 to 150 oC Note: Permanent device damage may occur if Absolute Maximum Ratings are exceeded. Functional operation shall be restricted to Recommended Operating Conditions. Exposure to higher than recommended voltages for extended periods of time could affect device reliability. Recommended Operating Conditions Parameter Symbol Min Typ Max Unit Supply Voltage for -7/-8/-10/-12 VDD 3.0 3.3 3.6 V Input High Voltage VIH 2.0 — VDD +0.3 V Input Low Voltage VIL –0.3 — 0.8 V Ambient Temperature, Commercial Range TAc 0 — 70 o Ambient Temperature, Industrial Range TAI –40 — 85 o C C Notes: 1. Input overshoot voltage should be less than VDD +2 V and not exceed 20 ns. 2. Input undershoot voltage should be greater than –2 V and not exceed 20 ns. Capacitance Parameter Symbol Test Condition Max Unit Input Capacitance CIN VIN = 0 V 5 pF Output Capacitance COUT VOUT = 0 V 7 pF Notes: 1. Tested at TA = 25°C, f = 1 MHz 2. These parameters are sampled and are not 100% tested. Rev: 1.07 12/2004 4/16 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. © 2001, GSI Technology GS71116ATP/J/U DC I/O Pin Characteristics Parameter Symbol Test Conditions Min Max Input Leakage Current IIL VIN = 0 to VDD –1 uA 1uA Output Leakage Current ILO Output High Z VOUT = 0 to VDD –1 uA 1uA Output High Voltage VOH IOH = –4 mA 2.4 Output Low Voltage VOL ILO = +4 mA 0.4V Power Supply Currents Parameter Symbol Test Conditions 0 to 70°C 10 ns 12 ns 7 ns IDD CE ≤ VIL All other inputs ≥ VIH or ≤ VIL Min. cycle time IOUT = 0 mA 145 mA 125 mA 100 mA 85 mA Standby Current ISB1 CE ≥ VIH All other inputs ≥ VIH or ≤VIL Min. cycle time 25 mA 15 mA Standby Current ISB2 CE ≥ VDD – 0.2 V All other inputs ≥ VDD – 0.2 V or ≤ 0.2 V Operating Supply Current Rev: 1.07 12/2004 7 ns 8 ns –40 to 85°C 20 mA 20 mA 10 ns 12 ns 150 mA 130 mA 105 mA 90 mA 30 mA 25 mA 20 mA 2 mA 5/16 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. 8 ns 25 mA 5 mA © 2001, GSI Technology GS71116ATP/J/U AC Test Conditions Output Load 1 Parameter Conditions Input high level VIH = 2.4 V Input low level VI L= 0.4 V 50Ω Input rise time tr = 1V/ns VT = 1.4 V Input fall time tf = 1 V/ns Input reference level 1.4 V Output Load 2 Output reference level 1.4 V 3.3 V Output load Fig. 1& 2 DQ Rev: 1.07 12/2004 589Ω DQ Notes: 1. Include scope and jig capacitance. 2. Test conditions as specified with output loading as shown in Fig. 1 unless otherwise noted. 3. Output load 2 for tLZ, tHZ, tOLZ and tOHZ 6/16 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. 30pF1 5pF1 434Ω © 2001, GSI Technology GS71116ATP/J/U AC Characteristics Read Cycle Parameter Symbol Read cycle time -7 -8 -10 -12 Unit Min Max Min Max Min Max Min Max tRC 7 — 8 — 10 — 12 — ns Address access time tAA — 7 — 8 — 10 — 12 ns Chip enable access time (CE) tAC — 7 — 8 — 10 — 12 ns Byte enable access time (UB, LB) tAB — 3 — 3.5 — 4 — 5 ns Output enable to output valid (OE) tOE — 3 — 3.5 — 4 — 5 ns Output hold from address change tOH 3 — 3 — 3 — 3 — ns Chip enable to output in low Z (CE) tLZ* 3 — 3 — 3 — 3 — ns Output enable to output in low Z (OE) tOLZ* 0 — 0 — 0 — 0 — ns Byte enable to output in low Z (UB, LB) tBLZ* 0 — 0 — 0 — 0 — ns Chip disable to output in High Z (CE) tHZ* — 3.5 — 4 — 5 — 6 ns Output disable to output in High Z (OE) tOHZ* — 3 — 3.5 — 4 — 5 ns Byte disable to output in High Z (UB, LB) tBHZ* — 3 — 3.5 — 3.5 — 3.5 — * These parameters are sampled and are not 100% tested. Read Cycle 1: CE = OE = VIL, WE = VIH, UB and, or LB = VIL tRC Address tAA tOH Data Out Rev: 1.07 12/2004 Previous Data Data valid 7/16 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. © 2001, GSI Technology GS71116ATP/J/U Read Cycle 2: WE = VIH tRC Address tAA CE tAC tHZ tLZ tAB UB, LB tBHZ tBLZ OE tOE Data Out tOHZ Data valid tOLZ High impedance Write Cycle Parameter Symbol Write cycle time -7 -8 -10 -12 Unit Min Max Min Max Min Max Min Max tWC 7 — 8 — 10 — 12 — ns Address valid to end of write tAW 5 — 5.5 — 7 — 8 — ns Chip enable to end of write tCW 5 — 5.5 — 7 — 8 — ns Byte enable to end of write tBW 5 — 5.5 — 7 — 8 — ns Data set up time tDW 3.5 — 4 — 5 — 6 — ns Data hold time tDH 0 — 0 — 0 — 0 — ns Write pulse width tWP 5 — 5.5 — 7 — 8 — ns Address set up time tAS 0 — 0 — 0 — 0 — ns Write recovery time (WE) tWR 0 — 0 — 0 — 0 — ns Write recovery time (CE) tWR1 0 — 0 — 0 — 0 — ns Output Low Z from end of write tWLZ* 3 — 3 — 3 — 3 — ns Write to output in High Z tWHZ* — 3 — 3.5 — 4 — 5 ns * These parameters are sampled and are not 100% tested. Rev: 1.07 12/2004 8/16 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. © 2001, GSI Technology GS71116ATP/J/U Write Cycle 1: WE control tWC Address tAW tWR OE tCW CE tBW UB, LB tAS tWP WE tDW tDH Data valid Data In tWHZ tWLZ Data Out High impedance Write Cycle 2: CE control tWC Address tAW tWR1 OE tAS tCW CE tBW UB, LB tWP WE tDW Data valid Data In Data Out Rev: 1.07 12/2004 tDH High impedance 9/16 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. © 2001, GSI Technology GS71116ATP/J/U Write Cycle 3: UB, LB control tWC Address tAW tWR1 OE tAS tCW CE tBW UB, LB tWP WE tDW Data valid Data In Data Out Rev: 1.07 12/2004 tDH High impedance 10/16 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. © 2001, GSI Technology GS71116ATP/J/U 44-Pin, 400 mil SOJ L D c HE GE 23 E 44 22 e A A1 A A2 1 Symbol y B B1 Detail A Q Dimension in inch Dimension in mm min nom max min nom max A — — 0.148 — — 3.759 A1 0.025 — — 0.635 — — A2 0.105 0.110 0.115 2.667 2.794 2.921 B — 0.018 — — 0.457 — B1 0.026 0.028 0.032 0.660 0.711 0.813 c — 0.008 — — 0.203 — D 1.120 1.125 1.130 28.44 28.58 28.70 E 0.395 0.400 0.405 10.033 10.160 10.287 e — 0.05 — — 1.27 — HE 0.435 0.440 0.445 11.049 11.176 11.303 GE 0.360 0.370 0.380 9.144 9.398 9.652 L 0.082 0.087 0.106 2.083 2.210 2.70 y — — 0.004 — — 0.102 Q 0o — 7o 0o — 7o Notes: 1. Dimension D& E do not include interlead flash. 2. Dimension B1 does not include dambar protrusion/intrusion. 3. Controlling dimension: inches Rev: 1.07 12/2004 11/16 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. © 2001, GSI Technology GS71116ATP/J/U 44 Pin, 400 mil TSOP-II Symbol D c 22 e B y L L1 A1 A A2 1 A HE 23 E 44 Detail A Rev: 1.07 12/2004 Q Dimension in inch Dimension in mm min nom max min nom max A — — 0.047 — — 1.20 A1 0.002 — — 0.05 — — A2 0.037 0.039 0.041 0.95 1.00 1.05 B 0.01 0.014 0.018 0.25 0.35 0.45 c — 0.006 — — 0.15 — D 0.721 0.725 0.729 18.31 18.41 18.51 E 0.396 0.400 0.404 10.06 10.16 10.26 e — 0.031 — — 0.80 — HE 0.455 0.463 0.471 11.56 11.76 11.96 L 0.016 0.020 0.024 0.40 0.50 0.60 L1 — 0.031 — — 0.80 — y — — 0.004 — — 0.10 Q o — o o — 5o 0 5 0 Notes: 1. Dimension D& E do not include interlead flash. 2. Dimension B does not include dambar protrusion/intrusion. 3. Controlling dimension: mm 12/16 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. © 2001, GSI Technology GS71116ATP/J/U 6 mm x 8 mm Fine Pitch BGA 0.36(typ) D H G F E D C B A 0.22 ± 0.05 1 0.75(typ). 3.75 3 4 5.25 Rev: 1.07 12/2004 13/16 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. Ball Dia. 0.35 Pitch 0.75 6 5 Bottom View 2 pin A1 index 1.20(max) pin A1 index units: mm Top View 6.00 ± 0.10 8.00 ± 0.10 0.10 © 2001, GSI Technology GS71116ATP/J/U Ordering Information Part Number* Package Access Time Temp. Range GS71116ATP-7 400 mil TSOP-II 7 ns Commercial GS71116ATP-8 400 mil TSOP-II 8 ns Commercial GS71116ATP-10 400 mil TSOP-II 10 ns Commercial GS71116ATP-12 400 mil TSOP-II 12 ns Commercial GS71116ATP-7I 400 mil TSOP-II 7 ns Industrial GS71116ATP-8I 400 mil TSOP-II 8 ns Industrial GS71116ATP-10I 400 mil TSOP-II 10 ns Industrial GS71116ATP-12I 400 mil TSOP-II 12 ns Industrial GS71116AGP-7 Pb-free 400 mil TSOP-II 7 ns Commercial GS71116AGP-8 Pb-free 400 mil TSOP-II 8 ns Commercial GS71116AGP-10 Pb-free 400 mil TSOP-II 10 ns Commercial GS71116AGP-12 Pb-free 400 mil TSOP-II 12 ns Commercial GS71116AGP-7I Pb-free 400 mil TSOP-II 7 ns Industrial GS71116AGP-8I Pb-free 400 mil TSOP-II 8 ns Industrial GS71116AGP-10I Pb-free 400 mil TSOP-II 10 ns Industrial GS71116AGP-12I Pb-free 400 mil TSOP-II 12 ns Industrial GS71116AJ-7 400 mil SOJ 7 ns Commercial GS71116AJ-8 400 mil SOJ 8 ns Commercial GS71116AJ-10 400 mil SOJ 10 ns Commercial GS71116AJ-12 400 mil SOJ 12 ns Commercial GS71116AJ-7I 400 mil SOJ 7 ns Industrial GS71116AJ-8I 400 mil SOJ 8 ns Industrial GS71116AJ-10I 400 mil SOJ 10 ns Industrial GS71116AJ-12I 400 mil SOJ 12 ns Industrial GS71116AU-7 6 mm x 8 mm Fine Pitch BGA 7 ns Commercial GS71116AU-8 6 mm x 8 mm Fine Pitch BGA 8 ns Commercial GS71116AU-10 6 mm x 8 mm Fine Pitch BGA 10 ns Commercial GS71116AU-12 6 mm x 8 mm Fine Pitch BGA 12 ns Commercial GS71116AU-7I 6 mm x 8 mm Fine Pitch BGA 7 ns Industrial GS71116AU-8I 6 mm x 8 mm Fine Pitch BGA 8 ns Industrial Rev: 1.07 12/2004 14/16 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. Status © 2001, GSI Technology GS71116ATP/J/U Ordering Information Part Number* Package Access Time Temp. Range GS71116AU-10I 6 mm x 8 mm Fine Pitch BGA 10 ns Industrial GS71116AU-12I 6 mm x 8 mm Fine Pitch BGA 12 ns Industrial GS71116AGU-7 Pb-free 6 mm x 8 mm Fine Pitch BGA 7 ns Commercial GS71116AGU-8 Pb-free 6 mm x 8 mm Fine Pitch BGA 8 ns Commercial GS71116AGU-10 Pb-free 6 mm x 8 mm Fine Pitch BGA 10 ns Commercial GS71116AGU-12 Pb-free 6 mm x 8 mm Fine Pitch BGA 12 ns Commercial GS71116AGU-7I Pb-free 6 mm x 8 mm Fine Pitch BGA 7 ns Industrial GS71116AGU-8I Pb-free 6 mm x 8 mm Fine Pitch BGA 8 ns Industrial GS71116AGU-10I Pb-free 6 mm x 8 mm Fine Pitch BGA 10 ns Industrial GS71116AGU-12I Pb-free 6 mm x 8 mm Fine Pitch BGA 12 ns Industrial Status * Customers requiring delivery in Tape and Reel should add the character “T” to the end of the part number. For example: GS71116ATP-10T Rev: 1.07 12/2004 15/16 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. © 2001, GSI Technology GS71116ATP/J/U 1Mb Asynchronous Datasheet Revision History Rev. Code: Old; New Types of Changes Format or Content Page #/Revisions/Reason • Creation of new datasheet 71116A_r1 71116A_r1; 71116_r1_01 Content • Added 6 ns speed bin to entire document 71116A_r1_01; 71116A _r1_02 Content • Updated all power numbers • Changed 6 mm x 10 mm FPBGA package designator from U to X 71116A_r1_02; 71116A _r1_03 Content • Updated Recommended Operating Conditions table on page 4 • Changed FPBGA package from 6 x 10 to 6 x 8 (package U) • Updated Read Cycle AC Characteristics table 71116A_r1_03; 71116A _r1_04 Content • Removed 6 ns speed bin from entire document • Added 7 ns speed bin to entire document 71116A_r1_04; 71116A _r1_05 Content 71116A_r1_05; 71116A_r1_06 Content/Format 71116A_r1_06; 71116A_r1_07 Content/Format Rev: 1.07 12/2004 • Updated timings for tBHZ (Read Cycle) for 10 ns and 12 ns • Updated format • Added Pb-free information for TSOP-II package • Added Pb-free information for FP-BGA package 16/16 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. © 2001, GSI Technology