JWS-P-SERIES Peak current / Single output 70 ~ 480W Unit Type Power Supply 䡵 Model name JWS120P - 24 *24V output with cover Nominal output voltage Average output power Series name 䡵 Features JWS70P JWS120P JWS240P JWS480P (Low Voltage Directive) 3 year warranty 䢇 marking (Low Voltage Directive) 䢇 Applicable to peak output current, compact package 䢇 Universal Input (85 ~ 265VAC) 䢇 Power Factor & Harmonic Correction (Conform to EN61000-3-2) 䢇 EMI (Built to meet EN55011-A, EN55022-A, VCCI-A, FCC-A) 䢇 Remote ON/OFF control (JWS240P & JWS480P) 䡵 Specifications 1. Input voltage range 2. Power Factor 3. Cooling 4. Operating Temperature 5. Withstand Voltage 6. Conducted emission noise 7. Radiated emission noise 8. PFHC 9. Safety standard 10. Functions 85 ~ 265VAC ( 47 ~ 63Hz) Universal input 0.99 (typ) at 100VAC Average load, 0.92 (typ) at 200VAC Average load JWS70P, JWS120P: Convection cooling, JWS240P, JWS480P: Forced air by built-in blower –10 ~ +60°C (–10 ~ +50°C: 100%, +60°C: 60%) Input to output: 3kVAC (20mA), Input to FG: 2kVAC (20mA), Output to FG: 500VAC (100mA) for 1 min. Built to meet EN55011-A, EN55022-A, FCC class A, VCC I class A Built to meet EN55011-A, EN55022-A, FCC class A, VCC I class A Built to meet EN61000-3-2 Approved by UL1950 , CSA950 , EN60950 , VDE0160 and UL508 OVP, OCP, Thermal protection, JWS240P, JWS480P: Remote ON/OFF control (optional, Note) Note: JWS150P 24V output with cover model - UL508 approval is expencted to be confirmed in August 2002 䡵 Line-up Model JWS70P-24 JWS70P-48 JWS120P-24 JWS120P-48 JWS240P-24 JWS240P-36 JWS240P-48 JWS480P-24 JWS480P-48 JWS70P JWS120P JWS240P JWS480P Output Voltage 24V 48V 24V 48V 24V 36V 48V 24V 48V (*1) Operating time at peak output is less than 10 seconds. (Duty Average Output Current 3.0A 1.5A 5.0A 2.5A 10.0A 6.65A 5.0A 20.0A 10.0A Average Output Power 72W 72W 120W 120W 240W 239.4W 240W 480W 480W Peak output Current (*1) 6.0A 3.0A 10.0A 5.0A 20.0A 13.3A 10.0A 40.0A 20.0A Peak output Power (*1) 144W 144W 240W 240W 480W 478.8W 480W 960W 960W UL CSA EN 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 䡬 : Safety standard approved < = 0.5) 䡵 Outline drawing JWS70P 䢇Recommended Noise Filter MAW-1202-22 GO!! P134 䢇Recommended Power Supply Fixture GO!! P198 (Unit: mm) 29 JWS-P-SERIES Unit Type Power Supply 䡵 Outline drawing JWS120P 䢇Recommended Noise Filter 䢇Recommended Power Supply GO!! MAW-1202-22 Fixture P198 GO!! (Unit: mm) P134 JWS240P A A NOTE A: M4 tapped holes (20) for customer chassis mounting. [Screws must not protrude into power supply by more than 6m/m.] 䢇Recommended Noise Filter MAW-1205-22 GO!! P134 (Unit: mm) A JWS480P A A NOTE A: M4 tapped holes (16) for customer chassis mounting. [Screws must not protrude into power supply by more than 6m/m.] A (Unit: mm) 30