Safety-door Switch D4NS CSM_D4NS_DS_E_5_2 Multi-contact, Labor-saving, Environment-friendly, Next-generation Safety-door Switch • Lineup includes three contact models with 2NC/1NO and 3NC contact forms and MBB models in addition to the previous contact forms 1NC/1NO, and 2NC. • M12-connector models are available, saving on labor and simplifying replacement. • Standardized gold-clad contacts provide high contact reliability. Applicable to both standard loads and microloads. • Variety of metallic heads available. Be sure to read the “Safety Precautions” on page 10 and the “Precautions for All Safety Door Switches”. Model Number Structure Model Number Legend Switch (Standard type) Switch (High pull-force type) D4NS-@@@ D4NS-@@F-SJ 1 2 3 1. Conduit/Connector size 1:Pg13.5 (1-conduit) 2:G1/2 (1-conduit) 4:M20 (1-conduit) 6:G1/2 (2-conduit) 8:M20 (2-conduit) 9:M12 connector (1-conduit) 1 2 1. Conduit size 2:G1/2 (1-conduit) 4:M20 (1-conduit) 2. Built-in Switch A:1NC/1NO (slow-action) B:2NC (slow-action) C:2NC/1NO (slow-action) D:3NC (slow-action) E:1NC/1NO (MBB contact) F:2NC/1NO (MBB contact) 3. Head Mounting Direction F:Four mounting directions possible (Front-side mounting at shipping)/plastic D:Four mounting directions possible (Front-side mounting at shipping)/metal 2. Built-in Switch A:1NC/1NO (slow-action) B:2NC (slow-action) C:2NC/1NO (slow-action) D:3NC (slow-action) Operation Key D4DS-K@ 1 1. Operation Key Type 1:Horizontal mounting 2:Vertical mounting 3:Adjustable mounting (Horizontal) 5:Adjustable mounting (Horizontal/Vertical) Note: An order for the head part or the switch part alone cannot be accepted. (The Operation Key is sold separately.) 1 D4NS Ordering Information Switches (Operation Keys are sold separately.) : Models with certified direct opening contacts. Consult with your OMRON representative when ordering any models that are not listed in this table. Type Contact configuration 1NC/1NO 2NC Slow-action 2NC/1NO 1-Conduit 3NC 1NC/1NO Slow-action MBB contact 2NC/1NO 1NC/1NO 2NC Slow-action 2NC/1NO 2-Conduit 3NC 1NC/1NO Slow-action MBB contact 2NC/1NO 1-Conduit, with connector Slow-action Slow-action MBB contact Conduit opening/Connector D4NS-1AF * G1/2 D4NS-2AF * M20 D4NS-4AF Pg13.5 D4NS-1BF * G1/2 D4NS-2BF * M20 D4NS-4BF Pg13.5 D4NS-1CF * G1/2 D4NS-2CF * M20 D4NS-4CF Pg13.5 D4NS-1DF * G1/2 D4NS-2DF * M20 D4NS-4DF Pg13.5 D4NS-1EF G1/2 D4NS-2EF M20 D4NS-4EF Pg13.5 D4NS-1FF G1/2 D4NS-2FF M20 D4NS-4FF G1/2 D4NS-6AF M20 D4NS-8AF G1/2 D4NS-6BF M20 D4NS-8BF G1/2 D4NS-6CF M20 D4NS-8CF G1/2 D4NS-6DF M20 D4NS-8DF G1/2 D4NS-6EF M20 D4NS-8EF G1/2 D4NS-6FF M20 D4NS-8FF D4NS-9AF 1NC/1NO 2NC M12 connector 1NC/1NO 1NC/1NO 2NC 1-Conduit Slow-action (High pull-force type) 2NC/1NO 3NC Model Pg13.5 D4NS-9BF D4NS-9EF G1/2 D4NS-2AF-SJ * M20 D4NS-4AF-SJ * G1/2 D4NS-2BF-SJ * M20 D4NS-4BF-SJ * G1/2 D4NS-2CF-SJ * M20 D4NS-4CF-SJ * G1/2 D4NS-2DF-SJ * M20 D4NS-4DF-SJ * * Models with Korean S-mark certification. 2 D4NS Operation Keys Type Model Horizontal mounting D4DS-K1 Vertical mounting D4DS-K2 Adjustable mounting (Horizontal) D4DS-K3 Adjustable mounting (Horizontal/Vertical) D4DS-K5 Specifications Standards and EC Directives Certified Standard Ratings Conforms to the following EC Directives: TÜV (EN60947-5-1), CCC (GB14048.5) • • • • • • Machinery Directive Low Voltage Directive EN50047 EN60204-1 EN1088 GS-ET-15 Item AC-15 DC-13 Rated operating current (Ie) 3A 0.27 A Rated operating voltage (Ue) 240 V 250 V Note: Use a 10 A fuse type gI or gG that conforms to IEC60269 as a short-circuit protection device. This fuse is not built into the Switch. Certified Standards Certification body Utilization category Standard TÜV SÜD EN60947-5-1 (certified direct opening) UL *1 UL508, CSA C22.2 No.14 CQC (CCC) GB14048.5 KOSHA *2 EN60947-5-1 File No. Consult your OMRON representative for details. E76675 2003010305077330 2005-197 *1. Certification for CSA C22.2 No. 14 is authorized by the UL mark. *2. Only certain models have been certified. UL/CSA (UL508, CSA C22.2 No. 14) A300 Rated voltage 120 VAC 240 VAC Carry current 10 A Current (A) Make Break 60 6 30 3 Volt-amperes (VA) Make Break 7,200 720 Q300 Rated voltage 125 VDC 250 VDC Carry current 2.5 A Current (A) Make Break 0.55 0.55 0.27 0.27 Volt-amperes (VA) Make Break 69 69 3 D4NS Characteristics Degree of protection *1 IP67 (EN60947-5-1) Durability *2 Mechanical <Standard type> 1,000,000 operations min. <High pull-force type> 100,000 operations min. Electrical <Standard type> 500,000 operations min. (3 A resistive load at 250 VAC) *3 300,000 operations min. (10 A resistive load at 250 VAC) <High pull-force type> 100,000 operations min. (10 A resistive load at 250 VAC) Operating speed 0.05 to 0.5 m/s Direct opening force *4 <Standard type> 60 N min. <High pull-force type> 80 N min. Direct opening travel *4 10 mm min. Contact resistance 25 mΩ max. Minimum applicable load *5 1 mA resistive load at 5 VDC (N-level reference value) Rated insulation voltage (Ui) 300 V Rated frequency 50/60 Hz Protection against electric shock Class II (double insulation) Pollution degree (operating environment) 3 (EN60947-5-1) Impulse withstand voltage (EN60947-5-1) Between terminals of same polarity 2.5 kV Between terminals of different polarity 4 kV Between each terminal 6 kV and non-current carrying metallic parts Insulation resistance 100 MΩ min. 2 × 2 mm min. Contact gap Vibration resistance Malfunction 10 to 55 Hz, 0.75 mm single amplitude Shock resistance Destruction 1,000 m/s2 min. Malfunction 300 m/s2 min. Conditional short-circuit current 100 A (EN60947-5-1) Conventional free air thermal current (Ith) 10 A (EN60947-5-1) Ambient operating temperature −30 to 70°C (with no icing) Ambient operating humidity 95% max. Weight Approx. 96 g (D4NS-1CF) Note: 1. The above values are initial values. 2. The Switch contacts can be used with either standard loads or microloads. Once the contacts have been used to switch a load, however, they cannot be used to switch smaller loads. The contact surfaces will become rough once they have been used and contact reliability for smaller loads may be reduced. *1. The degree of protection is tested using the method specified by the standard (EN60947-5-1). Confirm that sealing properties are sufficient for the operating conditions and environment beforehand. Although the switch box is protected from dust or water penetration, do not use the D4NS in places where foreign material may enter through the key hole on the head, otherwise Switch damage or malfunctioning may occur. *2. The durability is for an ambient temperature of 5 to 35°C and an ambient humidity of 40% to 70%. For more details, consult your OMRON representative. *3. Do not pass the 3 A, 250 VAC load through more than 2 circuits. *4. These figures are minimum requirements for safe operation. *5. This value will vary with the switching frequency, environment, and reliability level. Confirm that correct operation is possible with the actual load beforehand. 4 D4NS Structure and Nomenclature Structure D4NS-@A@, D4NS-@B@, D4NS-@E@, D4NS-@AF-SJ, D4NS-@BF-SJ Operation key hole D4NS-@C@, D4NS-@D@, D4NS-@F@, D4NS-@CF-SJ, D4NS-@DF-SJ Head The head can be mounted in four directions. Sealing properties The switch casing ensures IP67 Terminal 11 Terminal 12 Terminal 31 (33) Terminal 32 (34) Terminal 11 Terminal 12 Terminal 21 Terminal 22 Terminal 31 (33) Terminal 32 (34) Note: The 2-conduit models have the same terminal arrangement. Contact Form Diagrams Show State with Key Inserted. Model Contact Contact form 11-12 33-34 Zb D4NS-@A@ D4NS-@AF-SJ D4NS-@B@ D4NS-@BF-SJ 1NC/1NO 11 12 33 34 11 12 31 32 Zb D4NS-@C@ D4NS-@CF-SJ 2NC/1NO 11 12 21 22 33 34 Zb D4NS-@D@ D4NS-@DF-SJ 3NC 11 12 21 22 31 32 D4NS-@E@ 1NC/1NO MBB * 11 12 33 34 Zb D4NS-@F@ 2NC/1NO MBB * Stroke Extraction completion position Operation Key insertion completion position Stroke Operation Key insertion completion position Extraction completion position 11-12 21-22 33-34 ON Stroke Extraction completion position Operation Key insertion completion position 11-12 21-22 31-32 ON Stroke Operation Key insertion completion position 11 12 21 22 33 34 Stroke Extraction completion position 11-12 21-22 33-34 NC contacts 11-12 and 31-32 have a certified direct opening mechanism. The terminals 11-12 and 31-32 can be used as unlike poles. NC contacts 11-12 and 21-22 have a certified direct opening mechanism. The terminals 11-12, 21-22, and 33-34 can be used as unlike poles. NC contacts 11-12, 21-22, and 31-32 have a certified direct opening mechanism. The terminals 11-12, 21-22, and 31-32 can be used as unlike poles. Extraction completion position ON Operation Key insertion completion position Only NC contacts 11-12 have a certified direct opening mechanism. The terminals 11-12 and 33-34 can be used as unlike poles. ON 11-12 33-34 Zb Remarks ON 11-12 31-32 Zb 2NC Operating pattern Only NC contacts 11-12 have a certified direct opening mechanism. The terminals 11-12 and 33-34 can be used as unlike poles. ON NC contacts 11-12 and 21-22 have a certified direct opening mechanism. Stroke Operation Key insertion completion position Extraction completion position The terminals 11-12, 21-22 and 33-34 can be used as unlike poles. * MBB (Make Before Break) contacts have an overlapping structure, so that before the normally closed contact (NC) opens, the normally open contact (NO) closes. 5 D4NS Dimensions (Unit: mm) Dimensions and Operating Characteristics 1-Conduit Models Head cap D4NS-1@F D4NS-2@F D4NS-4@F D4NS-2@F-SJ D4NS-4@F-SJ 7.5 Model 15.3 Red Operating characteristics 30.6 15.5 30.2 Key insertion force Key extraction force 4.4 41 33.5 2.5 Black 55 47±0.2 D4NS-1@F D4NS-2@F D4NS-4@F 21.5 20±0.1 22±0.1 2.15±0.05R mounting holes 6±3 mm 6±3 mm Total travel (TT) (28 mm) (28 mm) 60 N min. 10 mm min. 80N min. 10mm min. * Always maintain the above operating characteristics for safe use. 14.2 30 22±0.2 31 15N max. (50N max.) Pretravel (PT) Direct opening force * Direct opening stroke * 31.5 15 N max. 30 N max. D4NS-2@F-SJ D4NS-4@F-SJ Two, 4+0.15 dia. holes 0 depth: 5 2-Conduit Models Head cap D4NS-6@F D4NS-8@F 7.5 31.5 30.6 42±0.1 40±0.1 30.2 15.3 Red Model Operating characteristics 21.5 15.5 Key insertion force Key extraction force 4.4 Black 41 47 33.5 5.4 2.5 20.5 20±0.1 39±0.2 9±0.2 Cap (both sides) 42±0.2 56 max. 2.15±0.05R mounting holes 14.2 3 30 4+0.15 0 Two, depth: 5 15 N max. 30 N max. Pretravel (PT) 6±3 mm Total travel (TT) (28 mm) Direct opening force * Direct opening stroke * 25 dia. 22±0.1 D4NS-6@F D4NS-8@F 60 N min. 10 mm min. * Always maintain the above operating characteristics for safe use. dia. holes 1-Conduit Connector Models Head cap D4NS-9@F 7.5 Red 30.6 15.5 30.2 15.3 Operating characteristics Key insertion force Key extraction force 4.4 Black Model D4NS-9@F 15 N max. 30 N max. 41 33.5 Pretravel (PT) 6±3 mm Total travel (TT) (28 mm) 2.5 55 47±0.2 21.5 20±0.1 22±0.1 31.5 2.15±0.05R mounting holes M12 × 1 Two, depth: 5 dia. holes Direct opening force * Direct opening stroke * 60 N min. 10 mm min. * Always maintain the above operating characteristics for safe use. (14) 22±0.2 31 4+0.15 0 14.2 30 Note: 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. 2. There are fluctuations in the contact ON/OFF timing for Switches with multiple poles (2NC, 2NC/1NO, or 3NC). Confirm performance before application. 6 D4NS Operation Keys D4DS-K1 17.5 D4DS-K3 28 14 28 9 dia. 4 Angle adjustment screw 8 dia. 13 4.5 dia. 4.3 7 13 30 15 13 Four, 2.15R 7 9 30 28 6 40 56 Black 2 2 6.3 10.5 D4DS-K2 30 20° D4DS-K5 7 13 20.9 15 28 24.6 22.5 4 Mounting Holes (Enlargement) Angle adjustment screws 17 15 4.5 15 8 15° 30 41 2 4.3 43 55 7 13 Four, 2.15R Black 18° 41 6.5 18 43 (7) Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. 7 D4NS With Operation Key Inserted (Relationship between Insertion Radius and Key Hole) D4NS-1@F + D4DS-K1 (with Top-inserted Operation Key) D4NS-1@F + D4DS-K1 (with Front-inserted Operation Key) Red 44 to 46.5 Key insertion face (30.6) Horizontal key insertion radius R ≥ 200 Red Horizontal key insertion radius R ≥ 200 (15) (15) Black (30.6) 54.5 to 57.0 Key (41) insertion face Black Permissible difference in center lines between the Operation Key and key hole is ±1. The permissible difference in center lines between the Operation Key and key hole is ±1. Vertical key insertion radius R ≥ 200 44 to 46.5 Key insertion face Vertical key insertion radius R ≥ 200 (33.5) (8) Permissible difference in center lines between the Operation Key and key hole is ±1. 54.5 to 57.0 Key (41) insertion face The permissible difference in center lines between the Operation Key and key hole is ±1. D4NS-1@F + D4DS-K2 (with Front-inserted Operation Key) Red 40 to 42.5 Key insertion face (30.6) D4NS-1@F + D4DS-K2 (with Top-inserted Operation Key) Horizontal key insertion radius R ≥ 200 Horizontal key insertion radius R ≥ 200 Red (15) (15) Black Permissible difference in center lines between the Operation Key and key hole is ±1. 50.5 to 53.0 Key (41) insertion face Black The permissible difference in center lines between the Operation Key and key hole is ±1. (30.6) 40 to 42.5 Key insertion face Vertical key insertion radius R ≥ 200 (33.5) (27.5) Permissible difference in center lines between the Operation Key and key hole is ±1. Vertical key insertion radius R ≥ 200 (6) (8) 50.5 to 53.0 Key (41) insertion face The permissible difference in center lines between the Operation Key and key hole is ±1. Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. 8 D4NS D4NS-1@F + D4DS-K3 (with Front-inserted Operation Key) Red D4NS-1@F + D4DS-K3 (with Top-inserted Operation Key) 45 to 47.5 Key insertion face (30.6) 40 (40±0.15) Black Black Permissible difference in center lines between the Operation Key and key hole is ±1. (30.6) 45 to 47.5 Key insertion face Horizontal key insertion radius R ≥ 50 Red Horizontal key insertion radius R ≥ 50 55.5 to 58.0 Key insertion face (41) The permissible difference in center lines between the Operation Key and key hole is ±1. Vertical key insertion radius R ≥ 200 Horizontal key insertion radius R ≥ 200 (8) (33.5) Permissible difference in center lines between the Operation Key and key hole is ±1. 55.5 to 58.0 Key (41) insertion face The permissible difference in center lines between the Operation Key and key hole is ±1. D4NS-1@F + D4DS-K5 (with Top-inserted Operation Key) D4NS-1@F + D4DS-K5 (with Front-inserted Operation Key) Red 51.9 to 54.4 Key insertion face 43 ± 0.1 41 ± 0.1 Red (30.6) (43±0.1) (41±0.1) Black 62.4 to 64.9 Key insertion face Black Horizontal key insertion radius R ≥ 50 (30.6) 51.9 to 54.4 Key insertion face Permissible difference in center lines between the Operation Key and key hole is ±1. Horizontal key insertion radius R ≥ 50 (41) The permissible difference in center lines between the Operation Key and key hole is ±1. Vertical key insertion radius R ≥ 50 (33.5) Permissible difference in center lines between the Operation Key and key hole is ±1. Horizontal key insertion radius R ≥ 50 (8) (41) 62.4 to 64.9 Key insertion face The permissible difference in center lines between the Operation Key and key hole is ±1. Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. 9 D4NS Safety Precautions Refer to the “Precautions for All Switches” and “Precautions for All Safety Door Switches”. !CAUTION Electric shock may occasionally occur. Do not use metal connectors or metal conduits. Precautions for Safe Use • Do not use the Switch submersed in oil or water or in locations continuously subject to splashes of oil or water. Doing so may result in oil or water entering the Switch. (The IP67 degree of protection of the Switch specifies the amount of water penetration after the Switch is submerged in water for a certain period of time.) • Always attach the cover after completing wiring and before using the Switch. Also, do not turn ON the Switch with the cover open. Doing so may result in electric shock. • Do not switch circuits for two or more standard loads (250 VAC, 3 A). Doing so may adversely affect insulation performance. Mounting Holes • Use M4 screws and spring washers to mount the Switch and Operation Key, and tighten the screws to a suitable torque. To ensure safety, use screws that cannot be easily removed or another means to prevent the Switch and Operation Key from easily being removed. • As shown below, two studs with a maximum height of 4.8 mm and a diameter of 4 −0.05 −0.15 mm can be provided, the studs inserted into the holes on the bottom of the Switch, and the Switch secured at four locations to increase the mounting strength. Switch Mounting Holes and Studs Operation Key Mounting Holes • 1-Conduit Modules • Horizontal/Vertical Mounting (D4DS-K1/-K2) Two, M4 Two, M4 2.5±0.1 20±0.1 22±0.1 15±0.1 47±0.1 • Horizontal Adjustable Mounting (D4DS-K3) Stopper Installation Two, M4 Do not use a Switch as a stopper. Be sure to install a stopper as shown in the following illustration to ensure that the base of the Operation Key does not strike the Head, and adjust the stopper to be within the setting zone (0.5 to 3 mm) of the base of the Operation Key. Do not subject the Switch to a shock that exceeds the Switch's shock resistance of 1,000 m/s2. 22±0.1 -0.05 4-0.15 dia. Height: 4.8 max. 40±0.1 • Horizontal/Vertical Adjustable Mounting (D4DS-K5) • 2-Conduit Modules Two, M4 Two, M4 2.5±0.1 5.35±0.1 Correct Stopper Incorrect 39±0.1 41±0.1 or, 43±0.1 20±0.1 22±0.1 40±0.1 42±0.1 42±0.1 Operation key -0.05 4-0.15 dia. Height: 4.8 max. Switch Precautions for Correct Use The Switch contacts can be used with either standard loads or microloads. Once the contacts have been used to switch a load, however, they cannot be used to switch smaller loads. The contact surfaces will become rough once they have been used and contact reliability for smaller loads may be reduced. Mounting Method Appropriate Tightening Torque • Loose screws may result in malfunction. Tighten the screws to the specified torques. Terminal screw 0.6 to 0.8 N·m Cover mounting screw 0.5 to 0.7 N·m Head mounting screw 0.5 to 0.6 N·m Operation Key mounting screw 2.4 to 2.8 N·m Body mounting screw 0.5 to 0.7 N·m Connector 1.8 to 2.2 N·m Cap screw 1.3 to 1.7 N·m • When loosening a screw with an electrical screwdriver or similar tool while pressing down on the screw head, do not continue turning the screw past the point where the threads disengage. Doing so may strip the end of the threads. • Set the Operation Key so that it is within 1 mm of the center of the key hole. If the Operation Key is offset or at an angle, accelerated wear or breaking may result. • Observe the specified insertion radius for the Operation Key and insert it in a direction perpendicular to the key hole. Head Direction • The rotation of the Switch head may be adjusted to any of the four directions by loosening the head mounting screws at the four corners of the head. Make sure that no foreign materials enter through the head. • Do not insert or remove the Operation Key with the Switch head removed. Doing so may make it impossible to insert the Operation Key. Securing the Door When the door is closed (with the Operation Key inserted), the Operation Key may exceed the set zone because of, for example, the door's own weight, machine vibration, or the door cushion rubber. Secure the door with a stopper so that the Operation Key remains within the set zone. Set zone (0.5 to 3 mm) Operation Key 10 D4NS Wiring Pin arrangement of connector type Wiring • When connecting with insulation tubes and M3.5 crimp terminals, connect the terminals as shown in the following figure and wire without overriding to the case and the cover. Adequate conductor size is AWG 20 to AWG18 (0.5 to 0.75 mm2). Prepare lead wires using the lengths given in the following diagrams. If lead wires are too long, they will press against the cover causing the cover to not close properly. 1-Conduit Models with 3 Poles 11 12 B C 21 22 D E 33 34 F F 42 mm 33 mm 28 mm Tolerance ±2 mm 2-Conduit Models with 3 Poles ECA A 11 12 B Left hand Right hand BD F C 21 22 BD F 33 34 D 42 mm 28 mm F 28 mm Tolerance ±2 mm Tolerance ±2 mm • Do not push the crimp terminal and the likes into the opening between the parts to prevent the case from being broken and deformed. • Use terminals having the thickness of 0.5 mm or less to avoid the contact between the terminal and the Switch case inside. <Reference> The crimp terminals listed below have a thickness of 0.5 mm or less. 3 (31) 4 (32) Zb 1 (11) 2 (12) 3 (33) 4 (34) • Suitable socket is XS2F-D421 series (OMRON). • Refer to the Connector Catalog for corresponding Socket pin numbers and lead wire colors. • Use cables with suitable diameters for the connector being used. • When wiring, place the enclosed cap screw on unused conduit openings (for 2-Conduit Switches) and tighten them to the suitable tightening torque. Recommended Connectors Use the connector with thread section of 9 mm long or less. If a connector with a longer thread section is used, the protruding part may interfere with the other parts inside the body. Use the connectors listed below to ensure IP67 degree of protection. Manufacture Model Type FN0.5-3.7 (F Type) J.S.T. Mfg Co. L 0.5 mm 3.7 mm 2.9 mm 6.6 mm 19 mm D dia. 7.7 mm 8.0 mm l F B Applicable cable diameter G1/2 LAPP ST-PF1/2 5380-1002 6.0 to 12.0 mm Pg13.5 LAPP S-13.5 5301-5030 6.0 to 12.0 mm M20 LAPP ST-M20 × 1.5 5311-1020 7.0 to 13.0 mm N0.5-3.7 (Straight Type) J.S.T is a Japanese manufacturer. t: dz dia.: D dia.: B: L: F: I: 2 (12) Pin No. (Terminal No.) Size Manufacture 1 (11) D4NS-9AF (1NC/1NO) D4NS-9EF (1NC/1NO (MBB)) Conduit Opening ECA 42 mm E 3 Zb • Turn the tightening screws on the Socket by hand and tighten them until the gap between the Socket and Plug essentially disappears. • Make sure that the Socket’s connector is tightened securely, otherwise the rated degree of protection (IP67) of the D4NS may not be maintained, or the Socket connector may be loosened by vibration. D E C D4NS-9BF (2NC) 4 Socket Tightening (Models with Connectors) AB A 1 2 When use LAPP's products, use together with a Seal Packing which is sold separately (Type names, JPK-16, GP-13.5, or GPM20) and tighten with proper tightening torque. • LAPP is a German manufacturer. dz dia. Terminal screw Crimp terminal Correct Incorrect 11 Read and Understand This Catalog Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranty and Limitations of Liability WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. Application Considerations SUITABILITY FOR USE OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's application or use of the products. At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog. Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. Systems, machines, and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to the products. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. PROGRAMMABLE PRODUCTS OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof. Disclaimers CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual specifications of purchased products. DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. PERFORMANCE DATA Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability. ERRORS AND OMISSIONS The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions. 2012.1 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2012 All Right Reserved.