SRAM AS5C4009 Austin Semiconductor, Inc. 512K x 8 SRAM Ultra Low Power SRAM PIN ASSIGNMENT AVAILABLE AS MILITARY SPECIFICATION (Top View) 32-Pin DIP, 32-Pin SOJ & 32-Pin TSOP • SMD 5962-956131,2 • MIL STD-8831 FEATURES A18 1 32 Vcc • Ultra Low Power with 2V Data Retention (0.2mW MAX worst case Power-down standby) • Fully Static, No Clocks • Single +5V ±10% power supply • Easy memory expansion with CE\ and OE\ options • All inputs and outputs are TTL-compatible • Three state outputs • Operating temperature range: Ceramic -55oC to +125oC & -40oC to +85oC Plastic -40oC to +85oC3 A16 2 31 A15 A14 3 30 A17 A12 A7 A6 A5 A4 A3 A2 A1 A0 I/01 I/02 I/03 Vss 4 5 6 7 8 9 10 11 12 13 14 15 16 29 28 27 26 25 24 23 22 21 20 19 18 17 WE\ A13 A8 A9 A11 OE\ A10 CE\ I/08 I/07 I/06 I/05 I/04 1. Not applicable to plastic package 2. Applies to CW package only. 3. Contact factory for -55oC to +125oC OPTIONS MARKING • Timing 55ns access -55 4 70ns access -70 85ns access -85 100ns access -100 • Packages Ceramic Dip (600 mil) CW Ceramic SOJ5 ECJ Plastic TSOP DG • Options 2V data retention/very low power L No. 112 No. 502 No. 1002 GENERAL DESCRIPTION The AS5C4009 is organized as 524,288 x 8 SRAM utilizing a special ultra low power design process. ASI’s pinout adheres to the JEDEC standard for pinout on 4 megabit SRAMs. The evolutionary 32 pin version allows for easy upgrades from the 1 meg SRAM design. For flexibility in memory applications, ASI offers chip enable (CE\) and output enable (OE\) capabilities. These features can place the outputs in High-Z for additional flexibility in system design. This devices operates from a single +5V power supply and all inputs and outputs are fully TTL-compatible. Writing to these devices is accomplished when write enable (WE\) and CE\ inputs are both LOW. Reading is accomplished when WE\ remains HIGH and CE\ and OE\ go LOW. The device offers a reduced power standby mode when disabled, by lowering VCC to 2V and maintaining CE\ = 2V. This allows system designers to meet ultra low standby power requirements. 4. For DG package, contact factory 5. Contact Factory NOTE: Not all combinations of operating temperature, speed, data retention and low power are necessarily available. Please contact the factory for availability of specific part number combinations. Pin Name Function WE\ Write Enable Input CE\ Chip Select Input OE\ Output Enable Input A0 - A18 Address Inputs I/O1 - I/O8 Data Inputs/Outputs Vcc Power Vss Ground For more products and information please visit our web site at www.austinsemiconductor.com AS5C4009 Rev. 5.1 6/05 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 1 SRAM AS5C4009 Austin Semiconductor, Inc. FUNCTIONAL BLOCK DIAGRAM Clk. gen. Precharge circuit A18 A16 A14 A12 A7 Memory Array 1024 rows 512 x 8 columns Row select A6 A5 A4 A1 A0 I/O1 I/O Circuit Data cont I/O8 Column Select Data cont A9 A8 A13 A17 A15 A10 A11 A3 A2 CE\ WE\ Control logic OE\ AS5C4009 Rev. 5.1 6/05 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 2 SRAM AS5C4009 Austin Semiconductor, Inc. ABSOLUTE MAXIMUM RATINGS* Voltage on Vcc Supply Relative to Vss...................-.5V to +7.0V Voltage on any pin Relative to Vss..........................-.5V to +7.0V Storage Temperature ....................................-65°C to +150°C Operating Temperature Range.............................-55oC to +125oC Soldering Temperature Range...............................................260oC Maximum Junction Temperature**....................................+150°C Power Dissipation...................................................................1.0W *Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. ** Junction temperature depends upon package type, cycle time, loading, ambient temperature and airflow. ELECTRICAL CHARACTERISTICS AND RECOMMENDED DC OPERATING CONDITIONS (-55oC < TA < 125oC; Vcc = 5V +10%) SYMBOL ILI MIN -5 MAX 5 UNITS µΑ Output Leakage Current (CE\=VIH or OE\=VIH or WE\=VIL, VIO=VSS to VCC) ILO -5 5 µΑ Output Low Voltage (IOL = 2.1mA) VOL -- 0.4 V 15 Output High Voltage (IOH = -1.0 mA) VOH 2.4 -- V 15 Supply Voltage VCC 4.5 5.5 V 15 Input High (Logic 1) Voltage VIH 2.2 Vcc +0.5 V 1, 15 Input Low (Logic 0) Voltage VIL -0.5 0.8 V 2, 15 PARAMETER/CONDITION Input Leakage Current (VIN = VSS to VCC) SYM -55 MAX -70 -85 Cycle Time = Min., 100% Duty Cycle, IIO = 0mA, CE\ = VIL, VIN = VIH or VIL Icc1 100 90 80 70 mA TTL CE\ = VIH, Other inputs = VIL or VIH ISB 6 6 6 6 mA CMOS CE\ = Vcc -0.2V, Other inputs = 0 ~ Vcc ISB1 0.75 0.75 0.75 0.75 mA PARAMETER CONDITIONS Power Supply Current: Operating Power Supply Current: Standby AS5C4009 Rev. 5.1 6/05 NOTES -100 UNITS NOTES 3 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 3 SRAM AS5C4009 Austin Semiconductor, Inc. CAPACITANCE PARAMETER Input Capacitance Input/Output Capactiance SYMBOL MAXIMUM UNITS NOTES VIN=0V CIN 8 pF 4 VIO=0V CIO 10 pF 4 CONDITIONS o TA = 25 C, f = 1MHz VCC = 5V ELECTRICAL CHARACTERISTICS AND RECOMMENDED AC OPERATING CONDITIONS (-55oC < TA < 125oC; Vcc = 5V +10%) DESCRIPTION SYM -55 MIN MAX -70 MIN MAX -85 MIN MAX -100 MIN MAX UNITS NOTES READ Cycle READ cycle Time t RC Address access time t AA 55 70 85 100 ns Chip Enable access time t ACE 55 70 85 100 ns Output hold from address change t OH 10 10 10 10 ns Chip Enable to output in Low-Z t LZCE 10 10 10 10 ns 4,6 Chip disable to output in High-Z t HZCE ns 4,6 ns 4 4 55 70 20 85 25 100 30 ns 30 Chip Enable to power-up time t PU Chip disable to power-down time t PD 55 70 85 100 ns Output Enable access time t AOE 30 35 40 45 ns Output Enable to output in Low-Z t LZOE Output disable to output in High-Z WRITE Cycle t HZOE 0 0 5 0 5 20 0 5 25 5 30 30 ns 4,6 ns 4,6 WRITE cycle time t WC 55 70 85 100 ns Chip Enable to end of write t CW 50 60 70 80 ns Address valid to end of write t AW 50 60 70 80 ns Address setup time t AS 0 0 0 0 ns Address hold from end of write t AH 0 0 0 0 ns t WP1 50 60 70 80 ns Data setup time t DS 30 30 35 40 ns Data hold time t DH 0 0 0 0 ns Write disable to output in Low-Z t LZWE 5 5 5 5 ns 4,6 Write Enable to output in High-Z t HZWE ns 4,6 WRITE pulse width AS5C4009 Rev. 5.1 6/05 25 25 30 30 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 4 SRAM AS5C4009 Austin Semiconductor, Inc. AC TEST CONDITIONS Input pulse levels ................................... Vss to 3.0V Input rise and fall times ....................................... 3ns Input timing reference levels ............................. 1.5V Output reference levels ..................................... 1.5V Output load ......................................... See Figures 1 50167 ohms ohms Q 1.73V C C=30pF = 100pF Fig. 1 Output Load Equivalent NOTES 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. tRC = Read Cycle Time. 11. Chip enable and write enable can initiate and terminate a WRITE cycle. 12. Output enable (OE\) is inactive (HIGH). 13. Output enable (OE\) is active (LOW). 14. ASI does not warrant functionality nor reliability of any product in which the junction temperature exceeds 150°C. Care should be taken to limit power to acceptable levels. 15. All voltage referenced to Vss (GND). Overshoot: Vcc +3.0V for pulse width < 20ms. Undershoot: -3V for pulse width < 20ms. ICC is dependent on output loading and cycle rates. This parameter is guaranteed but not tested. Test conditions as specified with the output loading as shown in Fig. 1 unless otherwise noted. At any given temperature and voltage condition, tHZCE is less than tLZCE, and tHZWE is less than tLZWE. WE\ is HIGH for READ cycle. Device is continuously selected. Chip enables and output enables are held in their active state. Address valid prior to, or coincident with, latest occurring chip enable. DATA RETENTION ELECTRICAL CHARACTERISTICS DESCRIPTION VCC for Retention Data CONDITIONS SYMBOL VDR MIN 2 MAX UNITS V CE\ > (VCC - 0.2V) VCC = 2V ICCDR 100 µA VIN > (VCC - 0.2V) VCC = 3V ICCDR 200 µA Data Retention Current Chip Deselect to Data Retention Time Operation Recovery Time AS5C4009 Rev. 5.1 6/05 NOTES tCDR 0 ns 4 tR 5 ms 4, 10 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 5 SRAM AS5C4009 Austin Semiconductor, Inc. LOW VCC DATA RETENTION WAVEFORM CE\ Controlled VCC 4.5V tSDR tRDR Data Retention 2.2V VDR CE\ > Vcc - 0.2V CE\ GND READ CYCLE NO. 1 1 (Address Controlled, CE\ = OE\ = VIL, WE\ = VIH) t RC ADDRESS tOH DATA OUT Previous Data Valid tAA 1234567 12345678901 12 1234567 12 1234567 12345678901 12 1234567 12 12345678901 1234567 12 1234567 12 1234567 12345678901 12 1234567 12 1234567 12 1234567 12 12345678901 1234567 12 1234567 12 12345678901 Data Valid READ CYCLE NO. 2 2 (WE\ = VIH) t RC ADDRESS tAA 1234567890123456789012 12345678901234567890 123456 12345678901234567890 1234567890123456789012 123456 12345678901234567890 123456 CE\1234567890123456789012 12345678901234567890 1234567890123456789012 123456 tOH 123456 123456789012345678901 12345678901234567890 123456 123456789012345678901 12345678901234567890 123456 123456789012345678901 12345678901234567890 123456 123456789012345678901 12345678901234567890 t CO1 12345678901234567890 1234567890123 12345678901234567890 1234567890123456789012 1234567890123 1234567890123456789012 12345678901234567890 1234567890123 12345678901234567890 1234567890123 OE\1234567890123456789012 12345678901234567890 1234567890123456789012 1234567890123 t t OE HZ 123456789 12345678901234567890 123456789 123456789012345678901 12345678901234567890 123456789012345678901 12345678901234567890 123456789 123456789 123456789012345678901 12345678901234567890 123456789 123456789012345678901 12345678901234567890 t OHZ DATA OUT High-Z t LZ t OLZ 1234567 12 1234 1234567 12 1234567 12 1234 1234567 12 1234567 12 1234 1234567 12 1234567 12 1234567 12 1234 1234567 12 1234 1234567 12 1234567 1234 1234567 Data Valid 1234567 1234567 11234 12 1234567 1234567 11234 12 1234567 1234567 11234 12 1234567 1234567 1 12 1234 1234567 1234567 1234 1 12 1234567 1234567 1234 12345 12345 12345 12345 Don’t Care 12345 12345 12345 12345 12345 12345 AS5C4009 Rev. 5.1 6/05 Undefined Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 6 SRAM AS5C4009 Austin Semiconductor, Inc. WRITE CYCLE NO. 1 (WE Controlled) t WC ADDRESS t CW(4) 1234567890123456789012 123456789012345678901 123456789 123456789012345678901 1234567890123456789012 123456789 1234567890123456789012 123456789 CE\123456789012345678901 123456789012345678901 1234567890123456789012 123456789 123456789012345678901 123456789 WE\ 1234567 1234567 1234567 tAS(5) 1234567 1234567 tWR(6) 123456 12345678901234567 1234567890123456 123456 12345678901234567 1234567890123456 12345678901234567 1234567890123456 123456 12345678901234567 1234567890123456 123456 1234567890123456 123456 t AW t WP(3) tDH tDW Data Valid DATA IN t WHZ DATA OUT tOW Data Undefined WRITE CYCLE NO. 2 (Write Enabled Controlled) t WC ADDRESS tAS(5) t CW(4) tWR(6) CE\ t AW 12345678901234567890123456 1234567890123456789012345 123456789 1234567890123456789012345 12345678901234567890123456 123456789 12345678901234567890123456 1234567890123456789012345 123456789 WE\12345678901234567890123456 1234567890123456789012345 123456789 1234567 123456789012345678 1234567 123456789012345678 123456789012345678 1234567 1234567 123456789012345678 t WP(3) tDW Data Valid DATA IN DATA OUT NOTES: AS5C4009 Rev. 5.1 6/05 tDH High-Z High-Z 1. tHZ and tOHZ are defined as the time at which the outputs achieve the open circuit conditions and are not referenced to output voltage levels. 2. At any given temperature adn voltage condition, tHZ (MAX) is less than tLZ (MIN) both for a given device and from device to device interconnection. 3. A write occurs during the overlap of a low CE\ adn a low WE\. A write begins at the latest transistion among CE\ going Low and WE\ going Low: A write end at the earliest transistion among CE\ going High and WE\ going High, tWP is measured from the beginning of write to the end of write. 4. tCW is measured from the CE\ going Low to end of write. 5. tAS is measured from the address valid to the beginning of write. 6. tWR is measure from the end of write to the address change. tWR applied in case a write ends are CE\ or WE\ going High. Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 7 SRAM AS5C4009 Austin Semiconductor, Inc. MECHANICAL DEFINITION* ASI Case #112 (Package Designator CW) D A L L1 b e Pin 1 b1 E b2 E1 ASI PACKAGE SYMBOL A b b1 b2 D E E1 e L L1 MIN 0.089 0.016 0.045 0.008 1.585 0.585 0.590 0.090 0.040 0.125 MAX 0.111 0.020 0.055 0.012 1.615 0.605 0.610 0.110 0.060 0.175 *All measurements are in inches. AS5C4009 Rev. 5.1 6/05 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 8 SRAM AS5C4009 Austin Semiconductor, Inc. MECHANICAL DEFINITION* ASI Case #502 (Package Designator ECJ) A b1 b2 e D L D1 E1 b A1 E *All measurements are in inches. AS5C4009 Rev. 5.1 6/05 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 9 SRAM AS5C4009 Austin Semiconductor, Inc. MECHANICAL DEFINITION* ASI Case #1002 (Package Designator DG) 0 - 8° 0.463±0.008 0.400 TYP 0.018 ~ 0.030 0.006 +0.004/-0.002 0.841 MAX 0.825 ± 0.004 0.039 ± 0.004 0.002 MIN 0.016 ± 0.004 0.037 TYP 0.047 MAX 0.004 MAX 0.050 TYP *All measurements are in inches. AS5C4009 Rev. 5.1 6/05 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 10 SRAM AS5C4009 Austin Semiconductor, Inc. ORDERING INFORMATION EXAMPLE: AS5C4009CW-55L/XT Device Number AS5C4009 AS5C4009 AS5C4009 AS5C4009 Package Type CW CW CW CW Speed ns -55 -70 -85 -100 EXAMPLE: AS5C4009DG-70/IT Device Number AS5C4009 AS5C4009 AS5C4009 AS5C4009 Package Type DG DG DG DG 1 EXAMPLE: AS5C4009ECJ-85L/883C Options** Process L L L L Device Number /* /* /* /* AS5C4009 AS5C4009 AS5C4009 AS5C4009 Package Type ECJ ECJ ECJ ECJ Speed ns -55 -70 -85 -100 1 Options** Process L L L L /* /* /* /* 2 Speed ns -55 -70 -85 -100 Options** Process L L L L /* /* /* /* *AVAILABLE PROCESSES IT = Industrial Temperature Range XT = Extended Temperature Range 883C = Full Military Processing -40oC to +85oC -55oC to +125oC -55oC to +125oC ** OPTIONS L = 2V Data Retention/Ultra Low Power NOTES: 1. All CSOJ devices, please consult factory. Not all combinations of operating temperature, speed, data retention and low power are necessarily available. Please contact the factory for availability of specific part number combinations. 2. Plastic devices not available as 883. For XT or 55ns devices, contact factory. AS5C4009 Rev. 5.1 6/05 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 11 SRAM Austin Semiconductor, Inc. AS5C4009 ASI TO DSCC PART NUMBER CROSS REFERENCE FOR 5962-95613 Package Designator CW ASI Part # AS5C4009CW-120/H AS5C4009CW-120L/H AS5C4009CW-100/H AS5C4009CW-100L/H AS5C4009CW-85/H AS5C4009CW-85L/H AS5C4009CW-70/H AS5C4009CW-70L/H SMD Part 5962-9561301HYA 5962-9561315HYA 5962-9561302HYA 5962-9561316HYA 5962-9561303HYA 5962-9561317HYA 5962-9561304HYA 5962-9561318HYA AS5C4009CW-120/H AS5C4009CW-120L/H AS5C4009CW-100/H AS5C4009CW-100L/H AS5C4009CW-85/H AS5C4009CW-85L/H AS5C4009CW-70/H AS5C4009CW-70L/H 5962-9561301HYC 5962-9561315HYC 5962-9561302HYC 5962-9561316HYC 5962-9561303HYC 5962-9561317HYC 5962-9561304HYC 5962-9561318HYC * ASI part number is for reference only. Orders received referencing the SMD part number will be processed per the SMD. AS5C4009 Rev. 5.1 6/05 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. 12