MN103S83D Type MN103S83D Internal ROM 64K-byte Internal RAM 2K-byte Package QFP084-P-1818E *Lead-free, LQFP080-P-1414A *Lead-free (under development) Minimum Instruction Execution Time 25 ns (at 4.3 V to 5.5 V, 10 MHz internal regulator used) 25 ns (at 3.0 V to 3.6 V, 10 MHz) *at internal 4 times oscillation used) Interrupts • 9 external interrupts • 40 internal interrupts (watch dog timer, timer, serial I/F, PWM, A/D, system error) Timer Counter 8-bit timer × 8 Timer 0 to 7: Interval timer, Event counter, Cascading connectable 16-bit timer × 4 Timer 8: Interval timer, Event counter, PWM output (6 pins simultaneous output are available), Double buffer Timer 9, 10: Interval timer, Event counter, PWM output, Double buffer Timer 11: Interval timer, Double buffer, Start synchronized with 3-phase PWM are available Watch dog timer UART (full duplex) / synchronous interfaces selective × 2 Serial 1: 7-bit, 8-bit transmission Serial 2: 1-bit to 8-bit transmission (synchronous), 2 and 3 channel type selectable (synchronous) Serial Interface I/O Pins I/O 50 Exclusive × 5, selective × 45 Input 10 Selective × 10 A/D Inputs 10-bit × 2 unit, 2 inputs × 2, 6 inputs × 1 Simultaneous conversion of 3 series are available, With S/H, Conversion start synchronized with 3-phase PWM or timer 11 are available Motor Control PWM 16-bit 3-phase PWM × 1 Minimum resolution: 50 ns Triangular waveform or jigsaw waveform dead time setup, Double buffer, Output polar switching is available, PWM output pin protect function Notes 5 V single power supply (Internal regulator) Electrical Characteristics A/D converter characteristics Parameter Limit Symbol Condition Unit min max ±3 10-bit Non-linear error typ A/D conversion time tAD 1.5 Analog input voltage VIA VSS LSB µs VDD V (Ta = 25°C, VDD = 5.0 V, VSS = 0 V) MAF00014DEM MN103S83D P37/TM7IO P36/TM6IO P35/TM5IO VDD P34/TM4IO VSS P33/TM3IO P32/TM2IO P31/TM1IO P30/TM0IO N.C. P27 P26 P25 P24/SBI1 P23/SBT1 P22/SBO1 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 P43/TM9BI P42/TM9AI P41/TM8BIO P40/TM8AIO P37/TM7IO P36/TM6IO P35/TM5IO VDD P34/TM4IO VSS P33/TM3IO P32/TM2IO P31/TM1IO P30/TM0IO P27 P26 P25 P24/SBI1 P23/SBT1 P22/SBO1 P40/TM8AIO 60 42 P21/SBI2 65 41 P20/SBT2 P46/TM10AI 66 40 N.C. P47/TM10BI 67 39 P17/SBO2 VPP 68 38 P14/IRQ08 VDD2 69 37 P13/IRQ07 P50/TM10AO 70 36 P12/IRQ06 VSS 71 35 P11/IRQ05 P51/TM10BO 72 34 P10/IRQ04 33 P07/NRST 32 LON VDD 73 P52/PWM00 74 P53/NPWM00 75 31 VDD P54/PWM01 76 30 VDD2 P55/NPWM01 77 29 PVDD P56/PWM02 78 28 PVSS P57/NPWM02 79 27 VSS N.C. 80 26 OSCI P60 81 25 OSCO P61 82 24 TEST3 P62/PWM10 83 23 TEST2 P63/PWM11 84 22 TEST1 14 15 16 17 18 19 20 21 VDD P84/ADIN20 P85/ADIN21 P86/ADIN22 P87/ADIN23 P90/ADIN24 P91/ADIN25 N.C. P83/ADIN11 9 P77/IRQ03 13 8 P82/ADIN10 7 P76/IRQ02 12 6 P75/IRQ01 11 5 P74/IRQ00 VSS 4 P67/PWM15 P81/ADIN01 3 P66/PWM14 10 2 P65/PWM13 P80/ADIN00 1 P64/PWM12 MN103S83D QFP084-P-1818E *Lead-free 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 P41/TM8BIO 61 64 P45/TM9BO P44/TM9AO P45/TM9BO P46/TM10AI P47/TM10BI VPP VDD2 P50/TM10AO VSS P51/TM10BO VDD P52/PWM00 P53/NPWM00 P54/PWM01 P55/NPWM01 P56/PWM02 P57/NPWM02 P60 P61 P62/PWM10 P63/PWM11 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 MN103S83D 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 P42/TM9AI 62 P44/TM9AO P64/PWM12 P65/PWM13 P66/PWM14 P67/PWM15 P74/IRQ00 P75/IRQ01 P76/IRQ02 P77/IRQ03 P80/ADIN00 P81/ADIN01 VSS P82/ADIN10 VDD P83/ADIN11 P84/ADIN20 P85/ADIN21 P86/ADIN22 P87/ADIN23 P90/ADIN24 P91/ADIN25 P43/TM9BI 63 Pin Assignment LQFP080-P-1414A *Lead-free (under development) Support Tool In-circuit Emulator PX-ICE-103S65 Flash Memory Built-in Type Type MN103SF65GBF, MN103SF65GAL ROM 128K-byte RAM 4K-byte Minimum instruction execution time 25 ns (at 4.3 V to 5.5 V, 10 MHz internal regulator used) 25 ns (at 3.0 V to 3.6 V, 10 MHz) Package MAF00014DEM QFP084-P-1818I *Lead-free, LQFP080-P-1414B *Lead-free P21/SBI2 P20/SBT2 P17/SBO2 P14/IRQ08 P13/IRQ07 P12/IRQ06 P11/IRQ05 P10/IRQ04 P07/NRST LON VDD VDD2 PVDD PVSS VSS OSCI OSCO TEST3 TEST2 TEST1 Request for your special attention and precautions in using the technical information and semiconductors described in this material (1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technical information described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. It neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) We are not liable for the infringement of rights owned by a third party arising out of the use of the technical information as described in this material. (4) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: • Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. • Any applications other than the standard applications intended. (5) The products and product specifications described in this material are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) When using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd. 2003 SEP