6-PIN DIP OPTOISOLATORS LOGIC OUTPUT H11L1M H11L2M H11L3M PACKAGE SCHEMATIC 6 VCC ANODE 1 6 6 CATHODE 2 1 5 GND 1 4 VO 3 6 1 Truth Table DESCRIPTION The H11LXM series has a high speed integrated circuit detector optically coupled to a gallium-arsenide infrared emitting diode. The output incorporates a Schmitt trigger, which provides hysteresis for noise immunity and pulse shaping. The detector circuit is optimized for simplicity of operation and utilizes an open collector output for maximum application flexibility. Input Output H L L H FEATURES • High data rate, 1 MHz typical (NRZ) • Free from latch up and oscilliation throughout voltage and temperature ranges. • Microprocessor compatible drive • Logic compatible output sinks 16 mA at 0.4 V maximum • Guaranteed on/off threshold hysteresis • Wide supply voltage capability, compatible with all popular logic systems • Underwriters Laboratory (UL) recognized—file #E90700, Volume 2 • VDE recognized – File#102497 – Add option V (e.g., H11LIVM) APPLICATIONS • • • • • • Logic to logic isolator Programmable current level sensor Line receiver—eliminate noise and transient problems A.C. to TTL conversion—square wave shaping Digital programming of power supplies Interfaces computers with peripherals © 2003 Fairchild Semiconductor Corporation Page 1 of 9 3/24/03 6-PIN DIP OPTOISOLATORS LOGIC OUTPUT H11L1M H11L2M H11L3M ABSOLUTE MAXIMUM RATINGS Parameters Symbol Device Value Units Storage Temperature TSTG All -55 to +150 °C Operating Temperature TOPR All -40 to +85 °C Lead Solder Temperature TSOL All 260 for 10 sec °C PD All Continuous Forward Current IF Reverse Voltage TOTAL DEVICE Total Device Power Dissipation @ 25°C 250 mW 2.94 mW/°C All 60 mA VR All 6 V IF(pk) All 3.0 A PD All 120 mW 1.41 mW/°C PD All V45 Allowed Range VO V65 Allowed Range Derate Above 25°C EMITTER Forward Current - Peak (1 µs pulse, 300 pps) LED Power Dissipation 25°C Ambient Derate Linearly From 25°C DETECTOR Detector Power Dissipation @ 25°C Derate Linearly from 25°C 150 mW 2.0 mW/°C All 0 to 16 V VCC All 3 to 16 V IO All 50 mA I4 Output Current ELECTRICAL CHARACTERISTICS (TA = 25°C Unless otherwise specified.) INDIVIDUAL COMPONENT CHARACTERISTICS Parameters Test Conditions Symbol Device VF All Min Typ Max 1.2 1.5 Units EMITTER Input Forward Voltage IF = 10 mA IF = 0.3 mA 0.75 1.0 V Reverse Current VR = 3 V IR All 10 µA Capacitance V = 0, f = 1.0 MHz CJ All 100 pF VCC All 15 V ICC(off) All 5.0 mA IOH All 100 µA DETECTOR Operating Voltage Range Supply Current IF = 0, VCC = 5V Output Current, High IF = 0, VCC = VO = 15V © 2003 Fairchild Semiconductor Corporation Page 2 of 9 3 1.6 3/24/03 6-PIN DIP OPTOISOLATORS LOGIC OUTPUT H11L1M H11L2M H11L3M ISOLATION CHARACTERISTICS Parameters Test Conditions Symbol Min 7500 Input-Output Isolation Voltage t =1 sec. VISO Isolation Capacitance VI-O = 0V, f = 1 MHz CISO Isolation Resistance VI-O = ±500 VDC Typ Max Units VPEAK 0.4 0.6 pF Ω 1011 RISO TRANSFER CHARACTERISTICS DC Characteristics Test Conditions Supply Current IF = 10mA, VCC = 5V Output Voltage, low RL=270Ω,VCC=5V, IF=IF(on) max. Turn-On Threshold Current RL=270Ω, VCC = 5V Symbol Device ICC(on) VOL IF(on)* Min Typ Max Units All 1.6 5.0 mA All 0.2 0.4 V H11L1M 1.6 H11L2M 10.0 H11L3M 5.0 Turn-Off Threshold Current RL=270Ω, VCC = 5V IF(off) All 0.3 1.0 Hysteresis Ratio RL=270Ω, VCC = 5V IF(off)/IF(on) All 0.50 0.75 0.90 Symbol Device Min Typ Max AC Characteristics Test Conditions mA mA Units SWITCHING SPEED Turn-On time Fall Time Turn-Off Time Rise time RL=270Ω, VCC = 5V, IF=IF(on), TA=25°C RL=270Ω, VCC = 5V, IF=IF(on), TA=25°C 1.0 ton 0.65 µs 4 0.1 tf All .05 µs 0.1 2.0 RL=270Ω, VCC = 5V, IF=IF(on), TA=25°C toff RL=270Ω, VCC = 5V, IF=IF(on), TA=25°C tr Data Rate All All 1.2 µs 4 0.1 All 0.07 µs 0.1 All 1.0 MHz NOTE: *Maximum IF(ON) is the maximum current required to trigger the output. For example, a 1.6mA maximum trigger current would require the LED to be driven at a current greater than 1.6mA to guarantee the device will turn on. A 10% guard band is recommended to account for degradation of the LED over its lifetime. The maximum allowable LED drive current is 60mA. © 2003 Fairchild Semiconductor Corporation Page 3 of 9 3/24/03 6-PIN DIP OPTOISOLATORS LOGIC OUTPUT H11L1M H11L2M C I6 H11L3M VIN 5V 5V IF 50% 0 1 RE H11L1 6 RL 4 VIN 270Ω VO toff ton tr = tf = 0.01µS Z = 50Ω 5 2 10% VO 90% tf tr Figure 1. Switching Test Circuit and Waveforms TYPICAL PERFORMANCE CURVES Figure 2. Transfer Characteristics Figure 3. Threshold Current vs. Supply Voltage VCC= 5V RL = 270 Ω TA = 25°C V OH 5 O V - OUTPUT VOLTAGE (V) IF - THRESHOLD CURRENT (NORMALIZED) 6 4 I F(OFF) I F(ON) 3 2 1 V OL 0 0 1 2 1.6 IF NORMALIZED TO : IF(ON) AT VCC = 5V 1.4 TA = 25oC 1.2 TURN ON THRESHOLD 1.0 TURN OFF THRESHOLD 0.8 0.6 0.4 0 3 2 6 8 10 12 14 16 VCC - SUPPLY VOLTAGE (V) IF - INPUT CURRENT (mA) Figure 4. Threshold Current vs. Supply Temperature Figure 5. Output Voltage, Low vs. Load Current 1.6 2 1.4 VOL - OUTPUT VOLTAGE, LOW (V) IF(On) , IF(Off) - THRESHOLD CURRENT (NORMALIZED) 4 1.2 1.0 0.8 NORMALIZED TO : VCC = 5V TA = 25oC 0.6 0.4 0.2 -50 -25 0 25 50 75 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 IF = IF(ON) VCC = 5V 100 RL = 270Ω TA - TEMPERATURE ( oC) 0.1 1 10 100 IO - LOAD CURRENT (mA) © 2003 Fairchild Semiconductor Corporation Page 4 of 9 3/24/03 6-PIN DIP OPTOISOLATORS LOGIC OUTPUT H11L1M H11L2M H11L3M TYPICAL PERFORMANCE CURVES Figure 6. Supply Current vs. Supply Voltage Figure 7. LED Forward Voltage vs. Forward Current 1.8 6 T A = 0 °C IF = 5mA 1.7 25 °C 70 °C VF - FORWARD VOLTAGE (V) IC - SUPPLY CURRENT (mA) 5 4 3 2 TA = 0°C 25°C 70°C 1 IF = 0mA 1.6 1.5 1.4 TA = 55°C 1.3 TA = 25°C 1.2 TA = 100°C 0 0 2 4 6 8 10 12 14 16 1.1 VCC - SUPPLY VOLTAGE (V) 1.0 1 10 100 IF - LED FORWARD CURRENT (mA) © 2003 Fairchild Semiconductor Corporation Page 5 of 9 3/24/03 6-PIN DIP OPTOISOLATORS LOGIC OUTPUT H11L1M H11L2M Package Dimensions (Through Hole) H11L3M Package Dimensions (Surface Mount) 0.350 (8.89) 0.320 (8.13) 0.350 (8.89) 0.320 (8.13) 0.260 (6.60) 0.240 (6.10) 0.070 (1.77) 0.040 (1.02) 0.260 (6.60) 0.240 (6.10) 0.390 (9.90) 0.332 (8.43) 0.070 (1.77) 0.040 (1.02) 0.320 (8.13) 0.014 (0.36) 0.010 (0.25) 0.320 (8.13) 0.014 (0.36) 0.010 (0.25) 0.200 (5.08) 0.115 (2.93) 0.200 (5.08) 0.115 (2.93) 0.100 (2.54) 0.015 (0.38) 0.012 (0.30) 0.008 (0.20) 0.025 (0.63) 0.020 (0.51) 0.020 (0.50) 0.016 (0.41) 0.100 (2.54) 0.100 [2.54] 15° 0.035 (0.88) 0.006 (0.16) 0.020 (0.50) 0.016 (0.41) 0.012 (0.30) Package Dimensions (0.4” Lead Spacing) Recommended Pad Layout for Surface Mount Leadform 0.350 (8.89) 0.320 (8.13) 0.070 (1.78) 0.260 (6.60) 0.240 (6.10) 0.060 (1.52) 0.070 (1.77) 0.040 (1.02) 0.014 (0.36) 0.010 (0.25) 0.425 (10.79) 0.100 (2.54) 0.305 (7.75) 0.200 (5.08) 0.115 (2.93) 0.030 (0.76) 0.100 (2.54) 0.015 (0.38) 0.020 (0.50) 0.016 (0.41) 0.100 [2.54] 0.012 (0.30) 0.008 (0.21) 0.425 (10.80) 0.400 (10.16) NOTE All dimensions are in inches (millimeters) © 2003 Fairchild Semiconductor Corporation Page 6 of 9 3/24/03 6-PIN DIP OPTOISOLATORS LOGIC OUTPUT H11L1M H11L2M H11L3M ORDERING INFORMATION Option/Order Entry Identifier Description S Surface Mount Lead Bend SR2 Surface Mount; Tape and reel T 0.4" Lead Spacing V VDE 0884 TV VDE 0884, 0.4" Lead Spacing SV VDE 0884, Surface Mount SR2V VDE 0884, Surface Mount, Tape & Reel MARKING INFORMATION 1 V 3 H11L1 2 X YY Q 6 5 4 Definitions 1 Fairchild logo 2 Device number 3 VDE mark (Note: Only appears on parts ordered with VDE option – See order entry table) 4 One digit year code, e.g., ‘3’ 5 Two digit work week ranging from ‘01’ to ‘53’ 6 Assembly package code *Note – ‘V’ option parts marked with date code ‘325’ or earlier are marked in portrait format. © 2003 Fairchild Semiconductor Corporation Page 7 of 9 3/24/03 6-PIN DIP OPTOISOLATORS LOGIC OUTPUT H11L1M H11L2M H11L3M Carrier Tape Specifications 12.0 ± 0.1 4.5 ± 0.20 2.0 ± 0.05 4.0 ± 0.1 0.30 ± 0.05 Ø1.5 MIN 1.75 ± 0.10 11.5 ± 1.0 21.0 ± 0.1 9.1 ± 0.20 10.1 ± 0.20 0.1 MAX 24.0 ± 0.3 Ø1.5 ± 0.1/-0 User Direction of Feed NOTE All dimensions are in inches (millimeters) Reflow Profile Temperature (°C) 300 230°C, 10–30 s 250 245°C peak 200 150 Time above 183°C, 120–180 sec 100 Ramp up = 2–10°C/sec 50 • Peak reflow temperature: 245°C (package surface temperature) • Time of temperature higher than 183°C for 120–180 seconds • One time soldering reflow is recommended 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 Time (Minute) © 2003 Fairchild Semiconductor Corporation Page 8 of 9 3/24/03 6-PIN DIP OPTOISOLATORS LOGIC OUTPUT H11L1M H11L2M H11L3M DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. © 2003 Fairchild Semiconductor Corporation 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Page 9 of 9 3/24/03