MCP3918
3V Single-Channel Analog Front End
Features:
Description:
• One 24-bit Resolution Delta-Sigma A/D Converter
• 93.5 dB SINAD, -107 dBc Total Harmonic
Distortion (THD) (up to 35th harmonic), 112 dB
Spurious-Free Dynamic Range (SFDR)
• Flexible Serial Interface that Includes Both SPI
and a Simple 2-Wire Interface Ideal for Polyphase
Shunt Energy Meters
• Advanced Security Features:
- 16-bit Cyclic Redundancy Check (CRC)
Checksum on All Communications for Secure
Data Transfers
- 16-bit CRC Checksum and Interrupt Alert for
Register-Map Configuration
- Register-Map Lock with 8-bit Secure Key
• 2.7V – 3.6V AVDD, DVDD
• Programmable Data Rate, up to 125 ksps:
- 4 MHz Maximum Sampling Frequency
- 16 MHz Maximum Master Clock
• Oversampling Ratio, up to 4096
• Ultra Low-Power Shutdown Mode with < 10 µA
• Low-Drift 1.2V Internal Voltage Reference:
9 ppm/°C
• Differential Voltage Reference Input Pins
• High-Gain Programmable Gain Amplifier (PGA)
(up to 32 V/V)
• Phase Delay Compensation with 1 µs Time
Resolution
• Separate Data Ready Pin for Easy
Synchronization
• Individual 24-bit Digital Offset and Gain Error
Correction
• High-Speed 20 MHz SPI Interface with Mode 0,0
and 1,1 Compatibility
• Continuous Read/Write Modes for Minimum
Communication with Dedicated 16-/32-bit Modes
• Available in 20-lead QFN and SSOP Packages
• Extended Temperature Range: -40°C to +125°C
(all specifications are valid down to -45°C)
The MCP3918 is a 3V single-channel Analog Front End
(AFE), containing one delta-sigma, Analog-to-Digital
Converter (ADC), one programmable gain amplifier
(PGA), phase delay compensation block, low-drift
internal voltage reference, digital offset and gain errors
calibration registers, and high-speed 20 MHz
SPI-compatible serial interface.
The MCP3918 ADC is fully configurable with features
such as: 16-/24-bit resolution, Oversampling Ratio
(OSR) from 32 to 4096, gain from 1x to 32x,
independent Shutdown and Reset, dithering and
auto-zeroing. Communication is largely simplified with
8-bit commands, including various continuous
read/write modes and 16-/24-/32-bit data formats that
can be accessed by the Direct Memory Access (DMA)
of an 8-/16-/32-bit MCU, and with the separate Data
Ready pin that can be directly connected to an Interrupt
Request (IRQ) input of an MCU.
The MCP3918 includes advanced security features to
secure the communications and the configuration
settings, such as a CRC-16 checksum on both serial
data outputs and on the register-map static
configuration. It also includes a register-map lock
through an 8-bit password to avoid the processing of
any unwanted write commands.
For polyphase shunt-based energy meters, the
MCP3918 2-Wire serial interface greatly reduces
system cost, requiring only a single bidirectional
isolator per phase.
The MCP3918 is capable of interfacing a variety of
voltage and current sensors, including shunts, current
transformers, Rogowski coils and Hall effect sensors.
2014 Microchip Technology Inc.
Applications:
•
•
•
•
•
•
•
Single-Phase and Polyphase Energy Meters
Energy Metering and Power Measurement
Automotive
Portable Instrumentation
Medical and Power Monitoring
Audio/Voice Recognition
Isolator Sensor Application
DS20005287A-page 1
MCP3918
Package Type
10
11
DGND
NC 4
SDO
REFIN-
SDI/OSR1
NC 3
DVDD
NC
AVDD
20
19
18
17
16
15
14
13
12
SDI/OSR1
SDO
SCK/MCLK
CS/BOOST
OSC2/MODE
OSC1/CLKI/GAIN0
DR/GAIN1
MDAT0
REFIN+/OUT
1
2
3
4
5
6
7
8
9
RESET/OSR0
DVDD
AVDD
CH0+
CH0NC
NC
AGND
RESET/OSR0
MCP3918
4 x 4 QFN*
MCP3918
SSOP
20 19 18 17 16
CH0+ 1
15 SCK/MCLK
CH0- 2
14 CS/BOOST
EP
21
13 OSC2/MODE
12 OSC1/CLKI/GAIN0
11 DR/GAIN1
DGND
9 10
MDAT0
8
NC
7
REFIN-
* Includes Exposed Thermal Pad (EP); see Table 3-1.
6
REFIN+/OUT
AGND 5
Functional Block Diagram
REFIN+/OUT
REFIN-
DVDD
AVDD
Voltage
Reference
+
-
AMCLK
VREFEXT
VREF
Xtal Oscillator
DMCLK/DRCLK
Vref-
Vref+
ANALOG
DIGITAL
DMCLK
SINC3+
SINC1
CH0+
+
CH0-
PGA
Single-Channel '6ADC
+
Φ
MCLK
Phase
Shifter
OSC1/CLKI/GAIN0
OSC2/MODE
OSR<2:0>
PRE<1:0>
OFFCAL_CH0 GAINCAL_CH0
<23:0>
<23:0>
DATA_CH0
<23:0>
MOD<3:0>
'6
Modulator
Clock
Generation
X
DR/GAIN1
SDO
PHASE <11:0>
Digital
Interfaces
(SPI & 2-wire)
RESET/OSR0
SDI/OSR1
SCK
CS/BOOST
EN_MDAT
MOD <3:0>
POR
AVDD
Monitoring
POR
DVDD
Monitoring
AGND
DS20005287A-page 2
Modulator
Output Block
MDAT0
DGND
2014 Microchip Technology Inc.
MCP3918
1.0
† Notice: Stresses above those listed under “Absolute
Maximum Ratings” may cause permanent damage to
the device. This is a stress rating only and functional
operation of the device at those or any other
conditions, above those indicated in the operational
listings of this specification, is not implied. Exposure to
maximum rating conditions for extended periods may
affect device reliability.
ELECTRICAL
CHARACTERISTICS
Absolute Maximum Ratings †
VDD ..................................................................... -0.3V to 4.0V
Digital inputs and outputs w.r.t. AGND ................ --0.3V to 4.0V
Analog input w.r.t. AGND ..................................... ....-2V to +2V
VREF input w.r.t. AGND ............................... -0.6V to VDD +0.6V
Storage temperature .....................................-65°C to +150°C
Ambient temp. with power applied ................-65°C to +125°C
Soldering temperature of leads (10 seconds) ............. +300°C
ESD on the analog inputs (HBM, MM) ................ 4.0 kV, 200V
ESD on all other pins (HBM, MM) ....................... 4.0 kV, 200V
1.1
Electrical Specifications
TABLE 1-1:
ANALOG SPECIFICATIONS
Electrical Specifications: Unless otherwise indicated, all parameters apply at AVDD = DVDD = 3V, MCLK = 4 MHz;
PRE<1:0> = 00; OSR = 256; GAIN = 1; VREFEXT = 0, CLKEXT = 1, DITHER<1:0> = 11; BOOST<1:0> = 10,
VCM = 0V; TA = -40°C to +125°C (Note 1); VIN = 1.2 VPP = -0.5 dBFS @ 50/60 Hz on all channels.
Characteristic
Sym.
Min.
Typ.
Max.
Units
Conditions
24
—
—
bits
OSR = 256 or greater
ADC Performance
Resolution
(No Missing Codes)
Sampling Frequency
fS(DMCLK)
—
1
4
MHz
For maximum condition,
BOOST<1:0> = 11
Output Data Rate
fD(DRCLK)
—
4
125
ksps
For maximum condition,
BOOST<1:0> = 11,
OSR = 32
CH0+/-
-1
—
+1
V
All analog input channels,
measured to AGND
IIN
—
+/-1
—
nA
RESET<0> = 1,
MCLK running continuously
—
+600/GAIN
mV
VREF = 1.2V,
proportional to VREF
-1
0.2
1
mV
Note 5
Analog Input Absolute
Voltage on CH0+/- pins
Analog Input
Leakage Current
Differential Input
Voltage Range
(CH0+-CH0-) -600/GAIN
Offset Error
VOS
Offset Error Drift
Gain Error
—
0.5
—
µV/°C
GE
-4
—
+4
%
—
1
—
ppm/°C
INL
—
5
—
ppm
Gain Error Drift
Integral Non-Linearity
Note 1:
2:
3:
4:
5:
6:
7:
Note 5
All specifications are valid down to -45°C.
This specification implies that the ADC output is valid over this entire differential range and that there is no distortion or
instability across this input range. Dynamic Performance specified at -0.5 dB below the maximum signal range,
VIN = 1.2 VPP = 424 mVRMS, VREF = 1.2V @ 50/60 Hz. See Section 4.0 “Terminology and Formulas” for definition.
This parameter is established by characterization and not 100% tested.
For these operating currents, the following configuration bit settings apply: SHUTDOWN<0> = 0, RESET<0> = 0,
VREFEXT = 0, CLKEXT = 0.
For these operating currents, the following configuration bit settings apply: SHUTDOWN<0> = 1, VREFEXT = 1,
CLKEXT = 1.
Applies to all gains. Offset and gain errors depend on the PGA gain setting. See Section 2.0 “Typical Performance
Curves” for typical performance.
Outside this range, the ADC accuracy is not specified. An extended input range of +/-2V can be applied continuously to
the part, with no damage.
For proper operation and for optimizing the ADC accuracy, AMCLK should be limited to the maximum frequency defined
in Table 5-2, as a function of the BOOST and PGA setting chosen. MCLK can take larger values as long as the
prescaler settings (PRE<1:0>) limit AMCLK = MCLK/PRESCALE within the defined range in Table 5-2.
2014 Microchip Technology Inc.
DS20005287A-page 3
MCP3918
TABLE 1-1:
ANALOG SPECIFICATIONS (CONTINUED)
Electrical Specifications: Unless otherwise indicated, all parameters apply at AVDD = DVDD = 3V, MCLK = 4 MHz;
PRE<1:0> = 00; OSR = 256; GAIN = 1; VREFEXT = 0, CLKEXT = 1, DITHER<1:0> = 11; BOOST<1:0> = 10,
VCM = 0V; TA = -40°C to +125°C (Note 1); VIN = 1.2 VPP = -0.5 dBFS @ 50/60 Hz on all channels.
Characteristic
Sym.
Min.
Typ.
Max.
Units
Measurement Error
ME
—
0.1
—
%
Differential Input
Impedance
ZIN
Conditions
Measured with a 10,000:1
dynamic range (from
600 mVPeak to 6 µVPeak),
AVDD = DVDD = 3V,
measurement points averaging
time: 20 seconds.
232
—
—
k
G = 1, proportional to 1/AMCLK
142
—
—
k
G = 2, proportional to 1/AMCLK
72
—
—
k
G = 4, proportional to 1/AMCLK
38
—
—
k
G = 8, proportional to 1/AMCLK
36
—
—
k
G = 16, proportional to 1/AMCLK
33
—
—
k
G = 32, proportional to 1/AMCLK
SINAD
92
93.5
—
dB
Total Harmonic Distortion (Note 2)
THD
—
-107
-103
dBc
Signal-to-Noise Ratio
(Note 2)
SNR
92
94
—
dB
SFDR
—
112
—
dBFS
AC Power Supply
Rejection
AC PSRR
—
-73
—
dB
AVDD = DVDD = 3V + 0.6VPP
50/60 Hz, 100/120 Hz
DC Power Supply
Rejection
DC PSRR
—
-73
—
dB
AVDD = DVDD = 2.7V to 3.6V
DC Common Mode
Rejection
DC CMRR
—
-105
—
dB
VCM from -1V to +1V
Signal-to-Noise and
Distortion Ratio (Note 2)
Spurious-Free Dynamic
Range (Note 2)
Note 1:
2:
3:
4:
5:
6:
7:
Includes the first
35 harmonics
All specifications are valid down to -45°C.
This specification implies that the ADC output is valid over this entire differential range and that there is no distortion or
instability across this input range. Dynamic Performance specified at -0.5 dB below the maximum signal range,
VIN = 1.2 VPP = 424 mVRMS, VREF = 1.2V @ 50/60 Hz. See Section 4.0 “Terminology and Formulas” for definition.
This parameter is established by characterization and not 100% tested.
For these operating currents, the following configuration bit settings apply: SHUTDOWN<0> = 0, RESET<0> = 0,
VREFEXT = 0, CLKEXT = 0.
For these operating currents, the following configuration bit settings apply: SHUTDOWN<0> = 1, VREFEXT = 1,
CLKEXT = 1.
Applies to all gains. Offset and gain errors depend on the PGA gain setting. See Section 2.0 “Typical Performance
Curves” for typical performance.
Outside this range, the ADC accuracy is not specified. An extended input range of +/-2V can be applied continuously to
the part, with no damage.
For proper operation and for optimizing the ADC accuracy, AMCLK should be limited to the maximum frequency defined
in Table 5-2, as a function of the BOOST and PGA setting chosen. MCLK can take larger values as long as the
prescaler settings (PRE<1:0>) limit AMCLK = MCLK/PRESCALE within the defined range in Table 5-2.
DS20005287A-page 4
2014 Microchip Technology Inc.
MCP3918
TABLE 1-1:
ANALOG SPECIFICATIONS (CONTINUED)
Electrical Specifications: Unless otherwise indicated, all parameters apply at AVDD = DVDD = 3V, MCLK = 4 MHz;
PRE<1:0> = 00; OSR = 256; GAIN = 1; VREFEXT = 0, CLKEXT = 1, DITHER<1:0> = 11; BOOST<1:0> = 10,
VCM = 0V; TA = -40°C to +125°C (Note 1); VIN = 1.2 VPP = -0.5 dBFS @ 50/60 Hz on all channels.
Characteristic
Sym.
Min.
Typ.
Max.
Units
Conditions
VREF
1.176
1.2
1.224
V
TCVREF
—
9
—
ZOUTVREF
—
0.6
—
k
VREFEXT = 0
AIDDVREF
—
54
—
µA
VREFEXT = 0,
SHUTDOWN<0> = 1
—
—
10
pF
Differential Input Voltage
Range (VREF+ – VREF-)
VREF
1.1
—
1.3
V
VREFEXT = 1
Absolute Voltage
on REFIN+ pin
VREF+
VREF- + 1.1
—
VREF- + 1.3
V
VREFEXT = 1
Absolute Voltage
on REFIN- pin
VREF-
-0.1
—
+0.1
V
REFIN- should be connected to
AGND when VREFEXT = 0
—
20
MHz
CLKEXT = 1 (Note 7)
—
20
MHz
CLKEXT = 0 (Note 7)
Note 7
Internal Voltage Reference
Tolerance
Temperature Coefficient
Output Impedance
Internal Voltage Reference Operating Current
VREFEXT = 0,
TA = +25°C only
ppm/°C TA = -40°C to +125°C,
VREFEXT = 0
Voltage Reference Input
Input Capacitance
Master Clock Input
Master Clock Input
Frequency Range
fMCLK
Crystal Oscillator
Operating Frequency
Range
fXTAL
1
Analog Master Clock
AMCLK
—
—
16
MHz
DIDDXTAL
—
80
—
µA
Operating Voltage, Analog
AVDD
2.7
—
3.6
V
Operating Voltage, Digital
DVDD
2.7
—
3.6
V
Operating Current, Analog
(Note 3)
IDD,A
—
0.8
1
mA
BOOST<1:0> = 00
—
1
1.2
mA
BOOST<1:0> = 01
—
1.3
1.7
mA
BOOST<1:0> = 10
—
2.2
2.9
mA
BOOST<1:0> = 11
Crystal Oscillator
Operating Current
CLKEXT = 0
Power Supply
Note 1:
2:
3:
4:
5:
6:
7:
All specifications are valid down to -45°C.
This specification implies that the ADC output is valid over this entire differential range and that there is no distortion or
instability across this input range. Dynamic Performance specified at -0.5 dB below the maximum signal range,
VIN = 1.2 VPP = 424 mVRMS, VREF = 1.2V @ 50/60 Hz. See Section 4.0 “Terminology and Formulas” for definition.
This parameter is established by characterization and not 100% tested.
For these operating currents, the following configuration bit settings apply: SHUTDOWN<0> = 0, RESET<0> = 0,
VREFEXT = 0, CLKEXT = 0.
For these operating currents, the following configuration bit settings apply: SHUTDOWN<0> = 1, VREFEXT = 1,
CLKEXT = 1.
Applies to all gains. Offset and gain errors depend on the PGA gain setting. See Section 2.0 “Typical Performance
Curves” for typical performance.
Outside this range, the ADC accuracy is not specified. An extended input range of +/-2V can be applied continuously to
the part, with no damage.
For proper operation and for optimizing the ADC accuracy, AMCLK should be limited to the maximum frequency defined
in Table 5-2, as a function of the BOOST and PGA setting chosen. MCLK can take larger values as long as the
prescaler settings (PRE<1:0>) limit AMCLK = MCLK/PRESCALE within the defined range in Table 5-2.
2014 Microchip Technology Inc.
DS20005287A-page 5
MCP3918
TABLE 1-1:
ANALOG SPECIFICATIONS (CONTINUED)
Electrical Specifications: Unless otherwise indicated, all parameters apply at AVDD = DVDD = 3V, MCLK = 4 MHz;
PRE<1:0> = 00; OSR = 256; GAIN = 1; VREFEXT = 0, CLKEXT = 1, DITHER<1:0> = 11; BOOST<1:0> = 10,
VCM = 0V; TA = -40°C to +125°C (Note 1); VIN = 1.2 VPP = -0.5 dBFS @ 50/60 Hz on all channels.
Characteristic
Sym.
Min.
Typ.
Max.
Units
Conditions
Operating Current, Digital
IDD,D
—
0.2
0.3
mA
MCLK = 4 MHz,
proportional to MCLK
—
0.7
—
mA
MCLK = 16 MHz,
proportional to MCLK
Shutdown Current, Analog
IDDS,A
—
—
1
µA
AVDD pin only (Note 4)
Shutdown Current, Digital
IDDS,D
—
—
2
µA
DVDD pin only (Note 4)
Pull-Down Current
on OSC2 Pin
(External Clock Mode)
IOSC2
—
35
—
µA
CLKEXT = 1
Note 1:
3:
4:
5:
6:
7:
1.2
All specifications are valid down to -45°C.
This specification implies that the ADC output is valid over this entire differential range and that there is no distortion or
instability across this input range. Dynamic Performance specified at -0.5 dB below the maximum signal range,
VIN = 1.2 VPP = 424 mVRMS, VREF = 1.2V @ 50/60 Hz. See Section 4.0 “Terminology and Formulas” for definition.
This parameter is established by characterization and not 100% tested.
For these operating currents, the following configuration bit settings apply: SHUTDOWN<0> = 0, RESET<0> = 0,
VREFEXT = 0, CLKEXT = 0.
For these operating currents, the following configuration bit settings apply: SHUTDOWN<0> = 1, VREFEXT = 1,
CLKEXT = 1.
Applies to all gains. Offset and gain errors depend on the PGA gain setting. See Section 2.0 “Typical Performance
Curves” for typical performance.
Outside this range, the ADC accuracy is not specified. An extended input range of +/-2V can be applied continuously to
the part, with no damage.
For proper operation and for optimizing the ADC accuracy, AMCLK should be limited to the maximum frequency defined
in Table 5-2, as a function of the BOOST and PGA setting chosen. MCLK can take larger values as long as the
prescaler settings (PRE<1:0>) limit AMCLK = MCLK/PRESCALE within the defined range in Table 5-2.
2:
Serial Interface Characteristics
TABLE 1-2:
SERIAL DC CHARACTERISTICS
Electrical Specifications: Unless otherwise indicated, all parameters apply at DVDD = 2.7 to 3.6 V,
TA = -40°C to +125°C (Note 1), CLOAD = 30 pF, applies to all digital I/O.
Characteristic
Sym.
Min.
Typ.
Max.
Units
Conditions
High-Level Input Voltage
VIH
0.7 DVDD
—
—
V
Schmitt-Triggered
Low-Level Input Voltage
VIL
—
—
0.3 DVDD
V
Schmitt-Triggered
Input Leakage Current
ILI
—
—
±1
µA
CS = DVDD,
VIN = DGND to DVDD
Output Leakage Current
ILO
—
—
±1
µA
CS = DVDD,
VOUT = DGND or DVDD
VHYS
—
300
—
mV
DVDD = 3.3V only (Note 3)
Hysteresis
of Schmitt-Triggered Inputs
Low-Level Output Voltage
VOL
—
—
0.4V
V
IOL = +1.7 mA, DVDD = 3.3V
High-Level Output Voltage
VOH
DVDD - 0.5
—
—
V
IOH = -1.7 mA, DVDD = 3.3V
Internal Capacitance
(All Inputs and Outputs)
CINT
—
—
7
pF
TA = +25°C, SCK = 1.0 MHz,
DVDD = 3.3V (Note 2)
Note 1:
2:
3:
All specifications are valid down to -45°C.
This parameter is periodically sampled and not 100% tested.
This parameter is established by characterization and not production tested.
DS20005287A-page 6
2014 Microchip Technology Inc.
MCP3918
TABLE 1-3:
SERIAL AC CHARACTERISTICS
Electrical Specifications: Unless otherwise indicated, all parameters apply at DVDD = 2.7 to 3.6 V,
TA = -40°C to +125°C (Note 1), GAIN = 1, CLOAD = 30 pF.
Characteristic
Sym
Min
Typ
Max
Units
fSCK
—
—
20
MHz
CS Setup Time
tCSS
25
—
—
ns
CS Hold Time
tCSH
50
—
—
ns
CS Disable Time
tCSD
50
—
—
ns
Serial Clock Frequency
Data Setup Time
tSU
5
—
—
ns
Data Hold Time
tHD
10
—
—
ns
Serial Clock High Time
tHI
20
—
—
ns
Serial Clock Low Time
tLO
20
—
—
ns
Serial Clock Delay Time
tCLD
50
—
—
ns
Serial Clock Enable Time
tCLE
50
—
—
ns
Output Valid from SCK Low
tDO
—
—
25
ns
Output Hold Time
tHO
0
—
—
ns
Output Disable Time
tDIS
—
—
25
ns
tMCLR
100
—
—
ns
Data Transfer Time to DR
(Data Ready)
tDODR
—
—
25
ns
Modulator Mode Entry to
Modulator Data Present
tMODSU
—
—
100
ns
tDRP
—
1/(2 x DMCLK)
—
µs
2-Wire Mode Enable Time
tMODE
—
—
50
ns
2-Wire Mode
Watchdog Timer
tWATCH
3.5
—
35
µs
Reset Pulse Width (RESET)
Data Ready Pulse Low Time
Note 1:
2:
Conditions
Note 2
All specifications are valid down to -45°C.
This parameter is established by characterization and not production tested.
TABLE 1-4:
TEMPERATURE SPECIFICATIONS
Electrical Specifications: Unless otherwise indicated, all parameters apply at AVDD = 2.7 to 3.6V,
DVDD = 2.7 to 3.6V.
Parameters
Sym.
Min.
Typ.
Max.
Units
Operating Temperature Range
TA
-40
—
+125
°C
Storage Temperature Range
TA
-65
—
+150
°C
Thermal Resistance, 20L 4x4 QFN
JA
—
46.2
—
°C/W
Thermal Resistance, 20L SSOP
JA
—
87.3
—
°C/W
Conditions
Temperature Ranges
Note 1, Note 2
Thermal Package Resistances
Note 1:
2:
The internal junction temperature (TJ) must not exceed the absolute maximum specification of +150°C.
All specifications are valid down to -45°C.
2014 Microchip Technology Inc.
DS20005287A-page 7
MCP3918
CS
fSCK
tHI
tCSH
tLO
Mode 1,1
SCK
Mode 0,0
tDO
tDIS
tHO
MSB out
SDO
LSB out
DON’T CARE
SDI
FIGURE 1-1:
Serial Output Timing Diagram.
tCSD
CS
tHI
Mode 1,1
SCK
tCLE
fSCK
tCSS
tCSH
tLO
tCLD
Mode 0,0
tSU
SDI
tHD
MSB in
Hi-Z
SDO
FIGURE 1-2:
LSB in
Serial Input Timing Diagram.
1/fD
tDRP
DR
tDODR
SCK
SDO
FIGURE 1-3:
DS20005287A-page 8
Data Ready Pulse/Sampling Timing Diagram.
2014 Microchip Technology Inc.
MCP3918
Waveform for tDIS
Timing Waveform for tDO
SCK
CS
VIH
tDO
90%
SDO
SDO
tDIS
Hi-Z
10%
FIGURE 1-4:
AVDD, DVDD
OSC2/
MODE
Timing Diagrams, continued.
SPI
Mode
0
SCK/MCLK
SDO
2-Wire
Mode
0
Hi-Z
0
tMODE
FIGURE 1-5:
Entering 2-Wire Interface
Mode Timing Diagram.
2014 Microchip Technology Inc.
DS20005287A-page 9
MCP3918
NOTES:
DS20005287A-page 10
2014 Microchip Technology Inc.
MCP3918
2.0
TYPICAL PERFORMANCE CURVES
Note:
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
Note: Unless otherwise indicated, AVDD = 3V, DVDD = 3V; TA = +25°C, MCLK = 4 MHz; PRESCALE = 1;
OSR = 256; GAIN = 1; Dithering = Maximum; VIN = -0.5 dBFS @ 60 Hz on all channels, VREFEXT = 0; CLKEXT = 1;
BOOST<1:0> = 10.
0
Amplitude (dB)
-40
-60
Am
mplitud
de (dB))
Vin = -0.5 dBFS @ 60 Hz
fD = 3.9 ksps
OSR = 256
Dithering = Off
16 ksamples FFT
-20
-80
-100
-120
-140
140
-160
-180
0
500
1000
1500
2000
0
-20
-40
-60
-80
-100
-120
-140
-160
-180
0
Frequency (Hz)
0
Vin = -60 dBFS @ 60 Hz
fD = 3.9 ksps
OSR = 256
Dithering = Off
16 ksamples FFT
Amplitude (dB
B)
20
-20
-40
-60
-80
-100
-120
-140
-160
-180
0
500
FIGURE 2-2:
1000
1500
Frequency (Hz)
2000
1000
Frequency (Hz)
1500
2000
Spectral Response.
1.0%
% Error Channel 0,1
0.5%
0.0%
-0.5%
-1.0%
0.01
0.1
1
10
100
1000
Current Channel Input Amplitude (mVPeak)
FIGURE 2-5:
Measurement Error
with 1-Point Calibration.
Spectral Response.
1.0%
Vin = -0.5 dBFS @ 60 Hz
fD = 3.9 ksps
OSR = 256
Dithering = Maximum
16 ksamples FFT
-20
-40
-60
-80
-100
-120
-140
140
Measurement Error (%)
0
Amplitude (dB)
500
FIGURE 2-4:
Spectral Response.
Measurement Error (%)
FIGURE 2-1:
Vin = -60 dBFS @ 60 Hz
fD = 3.9 ksps
OSR = 256
Dithering = Maximum
16 ksamples FFT
% Error Channel 0,1
0.5%
0.0%
-0.5%
-160
-180
0
FIGURE 2-3:
500
1000
Frequency (Hz)
1500
Spectral Response.
2014 Microchip Technology Inc.
2000
-1.0%
0.01
0.1
1
10
100
1000
Current Channel Input Amplitude (mVPeak)
FIGURE 2-6:
Measurement Error
with 2-Point Calibration.
DS20005287A-page 11
MCP3918
Standar deviation = 78 LSB
Noise = 7.4ȝVrms
16 ksamples
-108.2
-107.8
-107.4
-107.0
-106.6
Total Harmonic Distortion (-dBc)
( dBc)
-106.2
448
481
514
548
581
614
647
680
714
747
780
813
846
880
913
946
979
1,012
1,046
1,079
1,112
Frequ
uency of Occurrence
F
Freque
ency off Occurrence
e
Note: Unless otherwise indicated, AVDD = 3V, DVDD = 3V; TA = +25°C, MCLK = 4 MHz; PRESCALE = 1;
OSR = 256; GAIN = 1; Dithering = Maximum; VIN = -0.5 dBFS @ 60 Hz on all channels, VREFEXT = 0; CLKEXT = 1;
BOOST<1:0> = 10.
Output Noise (LSB)
FIGURE 2-10:
THD Repeatability
Freq
quency of Occurrence
Total Harmonic Distortion
(dBc)
FIGURE 2-7:
Histogram.
111.7
112.3 112.9 113.5 114.1 114.7 115.3
Spurious Free Dynamic Range (dBFS)
-90
Dithering=Maximum
Dithering=Medium
Dithering=Minimum
Dithering=Off
-95
-100
-105
-110
-115
-120
-125
-130
115.9
FIGURE 2-8:
Spurious-Free Dynamic
Range Repeatability Histogram.
Output Noise Histogram.
32
64 128 256 512 1024 2048 4096
Oversampling Ratio (OSR)
FIGURE 2-11:
THD vs.OSR.
Signal-to-N
Noise and
Disto
ortion R
Ratio (d
dB)
Frequency o
of Occu
urrence
e
110
105
100
95
90
85
80
75
70
65
60
93.3
93.4
93.5
93.6
93.7
Signal to Noise and Distortion (dB)
FIGURE 2-9:
Histogram.
DS20005287A-page 12
SINAD Repeatability
93.8
Dithering Maximu
Dithering=Maximu
m
Dithering=Medium
32
FIGURE 2-12:
64
128 256 512 1024 2048 4096
Oversampling Ratio (OSR)
SINAD vs. OSR.
2014 Microchip Technology Inc.
MCP3918
110
105
100
95
90
85
80
75
70
65
60
100
32
64
Spurio
ous Fre
ee Dyn
namic
Range ((dBFS))
R
90
85
80
75
70
SNR vs.OSR.
60
2
100
115
95
110
105
100
95
g
Dithering=Maximum
Dithering=Medium
Dithering=Minimum
Dithering=Off
Dithering
Off
85
80
32
64
128 256 512 1024 2048 4096
Oversampling
O
li
Ratio
R ti (OSR)
FIGURE 2-14:
4
6
8
10 12 14
MCLK Frequency (MHz)
FIGURE 2-16:
120
90
Boost = 00
Boost = 01
Boost = 10
65
128 256 512 1024 2048 4096
O
Oversampling
li
Ratio
R ti (OSR)
FIGURE 2-13:
SFDR vs. OSR.
16
18
SINAD vs. MCLK.
90
85
80
75
70
Boost = 00
Boost = 01
Boost = 10
Boost = 11
65
60
2
4
6
FIGURE 2-17:
8
10 12 14 16
MCLK Frequency (MHz)
18
SNR vs. MCLK.
120
-60
-65
-70
-75
-80
-85
-90
-95
100
-100
-105
-110
Boost = 00
Boost = 01
Boost = 10
Boost = 11
2
4
FIGURE 2-15:
6
8
10
12
14
16
MCLK Frequency (MHz)
THD vs. MCLK.
2014 Microchip Technology Inc.
18
Spurio
ous Fre
ee Dynamic
Range
(dBF
FS)
Tota
al Harmonic Distortion
(dB)
95
Sig
gnal-to
o-Noise
e and
Disttortion
(dB)
Dithering
Maximum
Dithering=Maximum
Dithering=Medium
Dithering=Minimum
Dithering=Off
Signal-to-Noise Rattio
(dB))
Signal-to--Noise Ratio ((dB)
Note: Unless otherwise indicated, AVDD = 3V, DVDD = 3V; TA = +25°C, MCLK = 4 MHz; PRESCALE = 1;
OSR = 256; GAIN = 1; Dithering = Maximum; VIN = -0.5 dBFS @ 60 Hz on all channels, VREFEXT = 0; CLKEXT = 1;
BOOST<1:0> = 10.
20
110
100
90
80
Boost = 00
Boost = 01
Boost = 10
Boost = 11
70
60
2
FIGURE 2-18:
4
6
8 10 12 14 16
MCLK Frequency (MHz)
18
20
SFDR vs. MCLK.
DS20005287A-page 13
MCP3918
0
140
OSR = 32
OSR = 64
OSR = 128
OSR = 256
OSR = 512
OSR = 1024
OSR = 2048
OSR = 4096
-20
-40
-60
-80
-100
-120
Spurious-Free Dynamic Range
(dBFS)
Total Harmonic Distortion (dB)
Note: Unless otherwise indicated, AVDD = 3V, DVDD = 3V; TA = +25°C, MCLK = 4 MHz; PRESCALE = 1;
OSR = 256; GAIN = 1; Dithering = Maximum; VIN = -0.5 dBFS @ 60 Hz on all channels, VREFEXT = 0; CLKEXT = 1;
BOOST<1:0> = 10.
120
100
-140
2
FIGURE 2-19:
4
8
Gain (V/V)
16
40
20
32
THD vs. GAIN.
1
2
FIGURE 2-22:
-20
Total Harmonic Distortion (dB)
120
100
80
60
OSR = 32
OSR = 64
OSR = 128
OSR = 256
OSR = 512
OSR = 1024
OSR = 2048
OSR = 4096
40
20
0
1
2
FIGURE 2-20:
4
8
Gain (V/V)
16
32
120
100
80
60
OSR = 32
OSR = 64
OSR = 128
OSR = 256
OSR = 512
OSR = 1024
OSR = 2048
OSR = 4096
40
20
0
1
2
FIGURE 2-21:
DS20005287A-page 14
4
8
Gain (V/V)
SNR vs. GAIN.
16
-60
32
16
32
SFDR vs. GAIN.
-80
-100
-120
0.001
0.01
0.1
1
10
100
Input Signal Amplitude (mVPK)
FIGURE 2-23:
Amplitude.
SINAD vs. GAIN.
4
8
Gain (V/V)
GAIN = 1x
GAIN = 2x
GAIN = 4x
GAIN = 8x
GAIN = 16x
GAIN = 32x
-40
Signal-to-Noise and Distortion
Ratio (dB)
Signal-to-Noise and Distortion
Ratio (dB)
OSR = 32
OSR = 64
OSR = 128
OSR = 256
OSR = 512
OSR = 1024
OSR = 2048
OSR = 4096
60
0
1
Signal-to-Noise Ratio (dB)
80
1000
THD vs. Input Signal
100
80
60
40
GAIN = 1x
GAIN = 2x
GAIN = 4x
GAIN = 8x
GAIN = 16x
GAIN = 32x
20
0
-20
0.001
0.01
0.1
1
10
100
Input Signal Amplitude (mVPK)
FIGURE 2-24:
Amplitude.
1000
SINAD vs. Input Signal
2014 Microchip Technology Inc.
MCP3918
80
60
40
GAIN = 1x
GAIN = 2x
GAIN = 4x
GAIN = 8x
GAIN = 16x
GAIN = 32x
20
0
-20
0.001
0.01
0.1
1
10
100
Input Signal Amplitude (mVPK)
-60
-80
-50
-25
0
FIGURE 2-28:
SNR vs. Input Signal
25
50
75
Temperature (°C)
100
125
THD vs. Temperature.
100
120
100
80
GAIN = 1x
GAIN = 2x
GAIN = 4x
GAIN = 8x
GAIN = 16x
GAIN = 32x
60
40
20
0.01
0.1
1
10
100
Input Signal Amplitude (mVPK)
FIGURE 2-26:
Amplitude.
OSR = 32
OSR = 64
OSR = 128
OSR = 256
OSR = 512
OSR = 1024
OSR = 2048
OSR = 4096
100
80
60
90
80
70
60
50
40
20
0
GAIN = 1x
GAIN = 2x
GAIN = 4x
GAIN = 8x
GAIN = 16x
GAIN = 32x
40
30
20
10
0
1000
SFDR vs. Input Signal
120
Signal-to-Noise and Distortion
Ratio (dB)
-40
-120
140
0
0.001
GAIN = 1x
GAIN = 2x
GAIN = 4x
GAIN = 8x
GAIN = 16x
GAIN = 32x
-20
Signal-to-Noise and Distortion
Ratio (dB)
Spurious-Free Dynamic Range
(dBFS)
FIGURE 2-25:
Amplitude.
1000
0
-100
-50
-25
0
FIGURE 2-29:
25
50
75
Temperature (°C)
100
125
SINAD vs. Temperature.
100
90
Signal-to-Noise Ratio (dB)
Signal-to-Noise Ratio (dB)
100
Total Harmonic Distortion (dB)
Note: Unless otherwise indicated, AVDD = 3V, DVDD = 3V; TA = +25°C, MCLK = 4 MHz; PRESCALE = 1;
OSR = 256; GAIN = 1; Dithering = Maximum; VIN = -0.5 dBFS @ 60 Hz on all channels, VREFEXT = 0; CLKEXT = 1;
BOOST<1:0> = 10.
80
70
60
50
GAIN = 1x
GAIN = 2x
GAIN = 4x
GAIN = 8x
GAIN = 16x
GAIN = 32x
40
30
20
10
0
10
FIGURE 2-27:
100
1000
10000
Signal Frequency (Hz)
100000
SINAD vs. Input Frequency.
2014 Microchip Technology Inc.
-50
-25
FIGURE 2-30:
0
25
50
75
Temperature (°C)
100
125
SNR vs. Temperature.
DS20005287A-page 15
MCP3918
Note: Unless otherwise indicated, AVDD = 3V, DVDD = 3V; TA = +25°C, MCLK = 4 MHz; PRESCALE = 1;
OSR = 256; GAIN = 1; Dithering = Maximum; VIN = -0.5 dBFS @ 60 Hz on all channels, VREFEXT = 0; CLKEXT = 1;
BOOST<1:0> = 10.
Internal Voltage Reference (V)
100
80
60
GAIN = 1x
GAIN = 2x
GAIN = 4x
GAIN = 8x
GAIN = 16x
GAIN = 32x
40
20
0
0
25
50
75
Temperature (°C)
100
1.198
125
SFDR vs. Temperature.
1000
GAIN = 1x
GAIN = 2x
GAIN = 4x
GAIN = 8x
GAIN = 16x
GAIN = 32x
800
600
400
200
0
-200
-400
-600
-800
-40
-20
0
FIGURE 2-34:
vs. Temperature.
Internal Voltage Reference (V)
-25
FIGURE 2-31:
Offset (µV)
1.199
1.197
-50
20 40 60 80
Temperature (°C)
100 120 140
Internal Voltage Reference
1.1969
1.1968
1.1967
1.1966
1.1965
1.1964
1.1963
1.1962
1.1961
-1000
-40
-20
0
FIGURE 2-32:
Gain.
20
40
60
80
Temperature (°C)
100
GAIN = 1x
GAIN = 2x
GAIN = 4x
GAIN = 8x
GAIN = 16x
GAIN = 32x
7
5
3
1
-1
-3
-5
-40
-20
0
FIGURE 2-33:
vs. Gain.
DS20005287A-page 16
20
40
60
80
Temperature (°C)
100
2.5 2.6 2.7 2.8 2.9 3 3.1 3.2 3.3 3.4 3.5 3.6
AVDD (V)
120
Offset vs. Temperature vs.
9
Gain Error (%)
1.2
120
Gain Error vs. Temperature
FIGURE 2-35:
Internal Voltage Reference
vs. Supply Voltage.
10
Integral Non-Linearity Error
(ppm)
Spurious-Free Dynamic Range
(dBFS)
120
8
6
4
2
0
-2
-4
-6
-8
-10
-0.6
-0.4
-0.2
0.0
0.2
Input Voltage (V)
0.4
0.6
FIGURE 2-36:
Integral Non-Linearity
(Dithering Maximum).
2014 Microchip Technology Inc.
MCP3918
Note: Unless otherwise indicated, AVDD = 3V, DVDD = 3V; TA = +25°C, MCLK = 4 MHz; PRESCALE = 1;
OSR = 256; GAIN = 1; Dithering = Maximum; VIN = -0.5 dBFS @ 60 Hz on all channels, VREFEXT = 0; CLKEXT = 1;
BOOST<1:0> = 10.
Integral Non-Linearity Error
(ppm)
10
8
6
4
2
0
-2
-4
-6
-8
-10
-0.6
-0.4
-0.2
0.0
0.2
Input Voltage (V)
IDD (mA)
FIGURE 2-37:
(Dithering Off).
3
2.75
2.5
2.25
2
1.75
1.5
1.25
1
0.75
0.5
0.25
0
0.4
0.6
Integral Non-Linearity
AIDD Boost = 2
AIDD Boost = 1
AIDD Boost = 0.66
AIDD Boost = 0.5
DIDD
2
4
6
8
10 12 14 16
MCLK Frequency (MHz)
18
20
FIGURE 2-38:
Operating Current vs. MCLK
Frequency vs. Boost, VDD = 3.0V.
2014 Microchip Technology Inc.
DS20005287A-page 17
MCP3918
NOTES:
DS20005287A-page 18
2014 Microchip Technology Inc.
MCP3918
3.0
PIN DESCRIPTION
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
SIX-CHANNEL MCP3918 PIN FUNCTION TABLE
MCP3918
SSOP
MCP3918
QFN
Symbol
1
18
RESET/OSR0
2
19
DVDD
Digital Power Supply Pin
3
20
AVDD
Analog Power Supply Pin
4
1
CH0+
Non-Inverting Analog Input Pin for Channel 0
5
2
CH0-
Inverting Analog Input Pin for Channel 0
6
3
NC
Not connected
7
4
NC
Not connected
8
5
AGND
9
6
REFIN+/OUT
10
7
REFIN-
11
8
DGND
3.1
Function
Master Reset Logic Input Pin or OSR0 Logic Input Pin
Analog Ground Pin, Return Path for internal analog circuitry
Non-Inverting Voltage Reference Input and Internal Reference
Output Pin
Inverting Voltage Reference Input Pin
Digital Ground Pin, Return Path for internal digital circuitry
12
9
NC
13
10
MDAT0
Not connected
14
11
DR/GAIN1
15
12
OSC1/CLKI/GAIN0
Oscillator Crystal Connection Pin or External Clock Input Pin or
GAIN0 Logic Input Pin
16
13
OSC2/MODE
Oscillator Crystal Connection Input Pin or Serial Interface Mode
Logic Input Pin
17
14
CS/BOOST
Serial Interface Chip Select Input Pin or BOOST Logic Input Pin
18
15
SCK/MCLK
Serial Interface Clock Pin or Master Clock Input Pin
19
16
SDO
20
17
SDI/OSR1
—
21
EP
Modulator Data Output Pin for Channel 0
Data Ready Signal Output Pin or GAIN1 Logic Input Pin
Serial Interface Data Input Pin
Serial Interface Data Input Pin or OSR1 Logic Input Pin
Exposed Thermal Pad
Master Reset/OSR0 Logic Input
(RESET/OSR0)
In SPI mode, this pin is active low and places the entire
chip in a Reset state when active.
When RESET is logic low, all registers are reset to their
default value, no communication can take place, and
no clock is distributed inside the part, except in the
input structure if MCLK is applied (if MCLK is idle, then
no clock is distributed). This state is equivalent to a
Power-On Reset (POR) state.
Since the default state of the ADC is on, the analog
power consumption when RESET is logic low is
equivalent to when RESET is logic high. Only the digital
power consumption is largely reduced because this
current consumption is essentially dynamic and is
reduced drastically when there is no clock running.
2014 Microchip Technology Inc.
If MCLK is applied when RESET is logic low, all the
analog biases are enabled during a reset, so that the
part is fully operational just after a RESET rising edge.
If MCLK is not applied, there is a time after a hard reset
when the conversion may not accurately correspond to
the start-up of the input structure.
This input is Schmitt-triggered.
In 2-Wire Interface mode, this is the OSR0 logic select
pin (see Section 7.0 “2-Wire Serial Interface
Description” for the logic input table for OSR0 and
OSR1). The pin state is latched when the MODE
changes to 2-Wire Interface mode, and is relatched at
each watchdog timer reset.
DS20005287A-page 19
MCP3918
3.2
Digital VDD (DVDD)
DVDD is the power supply voltage for the digital circuitry
within the MCP3918. For optimal performance, it is
recommended to connect appropriate bypass
capacitors (typically a 10 µF in parallel with a 0.1 µF
ceramic). DVDD should be maintained between 2.7V
and 3.6V for specified operation.
3.3
Analog Power Supply (AVDD)
AVDD is the power supply voltage for the analog
circuitry within the MCP3918. It is recommended to
connect appropriate bypass capacitors (typically a
10 µF in parallel with a 0.1 µF ceramic). AVDD should
be maintained between 2.7V and 3.6V for specified
operation.
3.4
ADC Differential Analog Inputs
(CH0+/CH0-)
The CH0+/- pins are the fully differential analog voltage
inputs for the delta-sigma ADC.
The linear and specified region of the channels is
dependent on the PGA gain. This region corresponds
to a differential voltage range of ±600 mV/GAIN with
VREF = 1.2V.
The maximum absolute voltage, with respect to AGND,
for each CH0+/- input pin is ±1V with no distortion and
±2V with no breaking after continuous voltage. This
maximum absolute voltage is not proportional to the
VREF voltage.
3.5
Analog Ground (AGND)
AGND is the ground reference voltage for the analog
circuitry within the MCP3918. For optimal performance,
it is recommended to connect it to the same ground
node voltage as DGND, preferably with a star
connection.
If an analog ground plane is available, it is
recommended that these pins be tied to this plane of
the Printed Circuit Board (PCB). This plane should also
reference all other analog circuitry in the system.
3.6
Non-Inverting Reference Input,
Internal Reference Output
(REFIN+/OUT)
This pin is the non-inverting side of the differential
voltage reference input for the ADC or the internal
voltage reference output.
When VREFEXT = 1, an external voltage reference
source can be used, and the internal voltage reference
is disabled. When using an external differential voltage
reference, it should be connected to its VREF+ pin.
When using an external single-ended reference, it
should be connected to this pin.
When VREFEXT = 0, the internal voltage reference is
enabled and connected to this pin through a switch.
This voltage reference has minimal drive capability and
thus needs proper buffering and bypass capacitances
(a 0.1 µF ceramic capacitor is sufficient in most cases),
if used as a voltage source.
If the voltage reference is only used as an internal
VREF, adding bypass capacitance on REFIN+/OUT is
not necessary for keeping ADC accuracy, but a minimal
0.1 µF ceramic capacitance can be connected to avoid
EMI/EMC susceptibility issues due to the antenna
created by the REFIN+/OUT pin if left floating.
3.7
Inverting Reference Input (REFIN-)
This pin is the inverting side of the differential voltage
reference input for the ADC. When using an external
differential voltage reference, it should be connected to
its VREF- pin. When using an external single-ended
voltage reference, or when VREFEXT = 0 (default) and
using the internal voltage reference, the pin should be
directly connected to AGND.
3.8
Digital Ground Connection (DGND)
DGND is the ground reference voltage for the digital
circuitry within the MCP3918. For optimal performance,
it is recommended to connect it to the same ground
node voltage as AGND, preferably with a star
connection.
If a digital ground plane is available, it is recommended
that this pin be tied to this plane of the PCB. This plane
should also reference all other digital circuitry in the
system.
DS20005287A-page 20
2014 Microchip Technology Inc.
MCP3918
3.9
Modulator Output
(MDAT0)
MDAT0 is the output pin for the modulator serial bit
streams of the ADC. This pin is high-impedance when
the EN_MDAT bit is logic low. When the EN_MDAT bit
is enabled, the modulator bit stream of the ADC is
present on the pin and updated at the AMCLK
frequency (see Section 5.3.5 “Modulator Output
Block” for a complete description of the modulator
output). This pin can be directly connected to an MCU
or a DSP when a specific digital filtering is needed.
When the MDAT0 output pin is enabled, the DR output
is disabled. In 2-Wire Interface mode, this pin is
automatically inactive. Its state is high-impedance
during the 2-Wire mode (therefore this pin can be left
grounded in applications using exclusively the 2-Wire
Interface mode; this configuration improves the
EMI/EMC susceptibility of the device).
3.10
Data Ready Output/GAIN1 Logic
Input (DR/GAIN1)
In SPI mode, the Data Ready pin indicates if a new
conversion result is ready to be read. The default state
of this pin is logic high when DR_HIZ = 1 and is
high-impedance when DR_HIZ = 0 (default). After
each conversion is finished, a logic low pulse will take
place on the Data Ready pin to indicate the conversion
result is ready as an interrupt. This pulse is
synchronous with the master clock and has a defined
and constant width.
The Data Ready pin is independent from the SPI
interface and acts like an interrupt output. The Data
Ready pin state is not latched, and the pulse width (and
period) are both determined by the MCLK frequency,
oversampling rate, and internal clock prescale settings.
The Data Ready pulse width is equal to half a DMCLK
period and the frequency of the pulses is equal to
DRCLK (see Figure 1-3).
In 2-Wire Interface mode, this is the GAIN1 logic select
pin. See Section 7.0 “2-Wire Serial Interface
Description” for the logic input table for GAIN0 and
GAIN1. The pin state is latched when the MODE
changes to 2-Wire Interface mode, and is relatched at
each watchdog timer reset.
Note:
This pin should not be left floating when
the DR_HIZ bit is low; a 100 k pull-up
resistor
connected
to
DVDD
is
recommended.
2014 Microchip Technology Inc.
3.11
Crystal Oscillator/Master Clock
Input/GAIN0 Logic Input
(OSC1/CLKI/GAIN0)
In SPI mode, OSC1/CLKI and OSC2 provide the
master clock for the device. When CLKEXT = 0, a
resonant crystal or clock source with a similar
sinusoidal waveform must be placed across the OSC1
and OSC2 pins to ensure proper operation.
The typical clock frequency specified is 4 MHz. For
proper operation and in order to optimize ADC
accuracy, AMCLK should be limited to the maximum
frequency defined in Table 5-2 for the function of the
BOOST and PGA setting chosen. MCLK can take
larger values as long as the prescaler settings
(PRE<1:0>) limit AMCLK = MCLK/PRESCALE in the
defined range in Table 5-2. Appropriate load
capacitance should be connected to these pins for
proper operation.
In 2-Wire Interface mode, this is the GAIN0 logic select
pin. See Section 7.0 “2-Wire Serial Interface
Description” for the logic input table for GAIN0 and
GAIN1. The pin state is latched when the MODE
changes to 2-Wire Interface mode, and is relatched at
each watchdog timer reset.
Note:
3.12
When CLKEXT = 1, the crystal oscillator
is disabled. OSC1 becomes the master
clock input CLKI, a direct path for an
external clock source. One example
would be a clock source generated by an
MCU.
Crystal Oscillator Output/
Interface MODE Logic Input
(OSC2/MODE)
When CLKEXT = 0 (default), a resonant crystal or
clock source with a similar sinusoidal waveform must
be placed across the OSC1 and OSC2 pins to ensure
proper operation. Appropriate load capacitance should
be connected to these pins for proper operation.
When CLKEXT = 1 (default condition at POR), this pin
is the MODE selection pin for the digital interface.
When MODE is logic low, the SPI interface is selected
(see Section 6.0 “SPI Serial Interface Description”).
When MODE is logic high, the 2-Wire interface is
selected (see Section 7.0 “2-Wire Serial Interface
Description”). The MODE input is latched after a
POR, a Master Reset and/or a Watchdog Timer Reset.
DS20005287A-page 21
MCP3918
3.13
Chip Select/ Boost Logic Input
(CS/BOOST)
In SPI mode, this pin is the SPI chip select that enables
serial communication. When this pin is logic high, no
communication can take place. A chip select falling
edge initiates serial communication, and a chip select
rising edge terminates the communication. No
communication can take place even when CS is logic
low, if RESET is also logic low.
This input is Schmitt-triggered.
In the 2-Wire Interface mode, this is the Boost logic
select pin. See Section 7.0 “2-Wire Serial Interface
Description” for the logic input table for Boost. The pin
state is latched when the mode changes to 2-Wire
Interface mode, and is re-latched at each watchdog
timer reset.
3.14
Serial Data Clock/
Master Clock Input (SCK/MCLK)
In SPI mode, this is the serial clock pin for SPI
communication. Data is clocked into the device on the
rising edge of SCK. Data is clocked out of the device on
the falling edge of SCK.
The MCP3918 SPI interface is compatible with SPI 0,0
and 1,1 modes. SPI modes can be changed during a
CS high time.
The maximum clock speed specified is 20 MHz. SCK
and MCLK are two different and asynchronous clocks;
SCK is only required when a communication happens,
while MCLK is continuously required when the part is
converting analog inputs.
3.16
Serial Data/OSR1 Logic Input
(SDI/OSR1)
In SPI mode, this is the SPI data input pin. Data is
clocked into the device on the rising edge of SCK.
When CS is logic low, this pin is used to communicate
with 8-bit commands followed by data bytes that can be
16-/24- or 32-bit wide. The interface is half-duplex
(inputs and outputs do not happen at the same time).
Each communication starts with a chip select falling
edge followed by an 8-bit command word, entered
through the SDI pin. Each command is either a Read or
a Write command. Toggling SDI during a Read
command has no effect.
This input is Schmitt-triggered.
In 2-Wire Interface mode, this is the OSR1 logic select
pin. See Section 7.0 “2-Wire Serial Interface
Description” for the logic input table for OSR0 and
OSR1. The pin state is latched when the mode
changes to 2-Wire Interface Mode, and is relatched at
each watchdog timer reset.
3.17
Exposed Pad (EP)
Exposed Thermal Pad. This pin must be connected to
AGND for optimal accuracy and thermal performance.
This pad can also be left floating if necessary.
Connecting it to AGND is preferable for the lowest noise
performance and best thermal behavior.
This input is Schmitt-triggered.
In the 2-Wire Interface mode, this pin is defining the
master clock of the device (MCLK) and the serial clock
(SCK) for the interface simultaneously. In this mode,
the clock has to be provided continuously to ensure
proper operation. See Section 7.0 “2-Wire Serial
Interface Description” for more information and
timing diagrams of the 2-Wire interface protocol.
3.15
Serial Data Output (SDO)
This is the SPI data output pin. Data is clocked out of
the device on the falling edge of SCK.
This pin remains in a high-impedance state during the
command byte. It also stays high-impedance during the
entire communication for Write commands and when
the CS pin is logic high or when the RESET pin is logic
low. This pin is active only when a Read command is
processed. The interface is half-duplex (inputs and
outputs do not happen at the same time).
In the 2-Wire Interface Mode, this pin is the only digital
output pin, and sends synchronous frames at each
data ready with data bits clocked out on the falling edge
of SCK.
DS20005287A-page 22
2014 Microchip Technology Inc.
MCP3918
4.0
TERMINOLOGY AND
FORMULAS
4.1
This is the fastest clock present on the device. This is
the frequency of the crystal placed at the OSC1/OSC2
inputs when CLKEXT = 0 or the frequency of the clock
input at the OSC1/CLKI when CLKEXT = 1. In the 2Wire mode, this is the frequency present at the SCK
input pin. See Figure 4-1.
This section defines the terms and formulas used
throughout this data sheet. The following terms are
defined:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
MCLK – Master Clock
MCLK – Master Clock
AMCLK – Analog Master Clock
DMCLK – Digital Master Clock
DRCLK – Data Rate Clock
OSR – Oversampling Ratio
Offset Error
Gain Error
Integral Non-Linearity Error
Signal-to-Noise Ratio (SNR)
Signal-to-Noise and Distortion Ratio (SINAD)
Total Harmonic Distortion (THD)
Spurious-Free Dynamic Range (SFDR)
MCP3918 Delta-Sigma Architecture
Idle Tones
Dithering
PSRR
CMRR
ADC Reset Mode
Hard Reset Mode (RESET = 0)
ADC Shutdown Mode
Full Shutdown Mode
4.2
AMCLK – Analog Master Clock
AMCLK is the clock frequency that is present on the
analog portion of the device, after prescaling has
occurred via the PRE<1:0> bits in the CONFIG0
register (see Equation 4-1). The analog portion
includes the PGA and one delta-sigma modulator.
EQUATION 4-1:
MCLK
AMCLK = ------------------------------PRESCALE
TABLE 4-1:
MCP3918 OVERSAMPLING
RATIO SETTINGS
CONFIG0
Analog Master Clock
Prescale
PRE<1:0>
0
0
AMCLK = MCLK/1 (default)
0
1
AMCLK = MCLK/2
1
0
AMCLK = MCLK/4
1
1
AMCLK = MCLK/8
MODE
SCK
CLKEXT
PRE<1:0>
OSR<2:0>
1
OUT
0
1
Multiplexer
OUT
OSC1
1/PRESCALE
AMCLK
1/4
DMCLK
1/OSR
DRCLK
0
OSC2
Multiplexer
Xtal Oscillator
FIGURE 4-1:
4.3
MCLK
Clock Divider
Clock Divider
Clock Divider
Clock Sub-Circuitry.
DMCLK – Digital Master Clock
This is the clock frequency that is present on the digital
portion of the device, after prescaling and division by
four (Equation 4-2). This is also the sampling
frequency, which is the rate at which the modulator
outputs are refreshed. Each period of this clock
corresponds to one sample and one modulator output.
See Figure 4-1.
EQUATION 4-2:
AMCLK
MCLK
DMCLK = --------------------- = ---------------------------------------4
4 PRESCALE
2014 Microchip Technology Inc.
4.4
DRCLK – Data Rate Clock
This is the output data rate, i.e. the rate at which the
ADC outputs new data. Each new data is signaled by a
Data Ready pulse on the Data Ready pin.
This data rate is dependent on the OSR and the
prescaler with the formula in Equation 4-3.
EQUATION 4-3:
AMCLK
DMCLK
MCLK
DRCLK = ---------------------- = --------------------- = ----------------------------------------------------------4 OSR
OSR
4 OSR PRESCALE
DS20005287A-page 23
MCP3918
Since this is the output data rate, and because the
decimation filter is a sinc (or notch) filter, there is a
notch in the filter transfer function at each integer
multiple of this rate.
TABLE 4-2:
PRE<1:0>
Table 4-2 describes the various combinations of OSR
and PRESCALE, and their associated AMCLK,
DMCLK and DRCLK rates.
DEVICE DATA RATES IN FUNCTION OF MCLK, OSR AND PRESCALE,
MCLK = 4 MHZ
OSR<2:0>
OSR
AMCLK
DMCLK
DRCLK
DRCLK
(ksps)
SINAD
(dB)
Note 1
MCLK/8
MCLK/32
MCLK/131072
0.035
102.5
ENOB
from
SINAD
(bits)
Note 1
16.7
1
1
1
1
1
4096
1
1
1
1
0
2048
MCLK/8
MCLK/32
MCLK/65536
0.061
100
16.3
1
1
1
0
1
1024
MCLK/8
MCLK/32
MCLK/32768
0.122
97
15.8
1
1
1
0
0
512
MCLK/8
MCLK/32
MCLK/16384
0.244
96
15.6
1
1
0
1
1
256
MCLK/8
MCLK/32
MCLK/8192
0.488
95
15.5
1
1
0
1
0
128
MCLK/8
MCLK/32
MCLK/4096
0.976
90
14.7
1
1
0
0
1
64
MCLK/8
MCLK/32
MCLK/2048
1.95
83
13.5
1
1
0
0
0
32
MCLK/8
MCLK/32
MCLK/1024
3.9
70
11.3
1
0
1
1
1
4096
MCLK/4
MCLK/16
MCLK/65536
0.061
102.5
16.7
1
0
1
1
0
2048
MCLK/4
MCLK/16
MCLK/32768
0.122
100
16.3
1
0
1
0
1
1024
MCLK/4
MCLK/16
MCLK/16384
0.244
97
15.8
1
0
1
0
0
512
MCLK/4
MCLK/16
MCLK/8192
0.488
96
15.6
1
0
0
1
1
256
MCLK/4
MCLK/16
MCLK/4096
0.976
95
15.5
1
0
0
1
0
128
MCLK/4
MCLK/16
MCLK/2048
1.95
90
14.7
1
0
0
0
1
64
MCLK/4
MCLK/16
MCLK/1024
3.9
83
13.5
1
0
0
0
0
32
MCLK/4
MCLK/16
MCLK/512
7.8125
70
11.3
0
1
1
1
1
4096
MCLK/2
MCLK/8
MCLK/32768
0.122
102.5
16.7
0
1
1
1
0
2048
MCLK/2
MCLK/8
MCLK/16384
0.244
100
16.3
0
1
1
0
1
1024
MCLK/2
MCLK/8
MCLK/8192
0.488
97
15.8
0
1
1
0
0
512
MCLK/2
MCLK/8
MCLK/4096
0.976
96
15.6
0
1
0
1
1
256
MCLK/2
MCLK/8
MCLK/2048
1.95
95
15.5
0
1
0
1
0
128
MCLK/2
MCLK/8
MCLK/1024
3.9
90
14.7
0
1
0
0
1
64
MCLK/2
MCLK/8
MCLK/512
7.8125
83
13.5
0
1
0
0
0
32
MCLK/2
MCLK/8
MCLK/256
15.625
70
11.3
0
0
1
1
1
4096
MCLK
MCLK/4
MCLK/16384
0.244
102.5
16.7
0
0
1
1
0
2048
MCLK
MCLK/4
MCLK/8192
0.488
100
16.3
0
0
1
0
1
1024
MCLK
MCLK/4
MCLK/4096
0.976
97
15.8
0
0
1
0
0
512
MCLK
MCLK/4
MCLK/2048
1.95
96
15.6
0
0
0
1
1
256
MCLK
MCLK/4
MCLK/1024
3.9
95
15.5
0
0
0
1
0
128
MCLK
MCLK/4
MCLK/512
7.8125
90
14.7
0
0
0
0
1
64
MCLK
MCLK/4
MCLK/256
15.625
83
13.5
0
0
0
0
0
32
MCLK
MCLK/4
MCLK/128
31.25
70
11.3
Note 1: For OSR = 32 and 64, DITHER = None. For OSR = 128 and higher, DITHER = Maximum. The SINAD
values are given for GAIN = 1.
DS20005287A-page 24
2014 Microchip Technology Inc.
MCP3918
4.5
OSR – Oversampling Ratio
4.8
Integral Non-Linearity Error
This is the ratio of the sampling frequency to the output
data rate: OSR = DMCLK/DRCLK. The default OSR is
256,
with
MCLK = 4 MHz,
PRESCALE = 1,
AMCLK = 4 MHz, fS = 1 MHz, and fD = 3.90625 ksps.
The bits in Table 4-3, available in the CONFIG0
register, are used to change the oversampling ratio
(OSR).
Integral non-linearity error is the maximum deviation of
an ADC transition point from the corresponding point of
an ideal transfer function, with the offset and gain
errors removed, or with the end points equal to zero.
TABLE 4-3:
4.9
MCP3918 OVERSAMPLING
RATIO SETTINGS
CONFIG0
OSR<2:0>
Oversampling Ratio
(OSR)
0
0
0
32
0
0
1
64
0
1
0
128
0
1
1
256 (Default)
1
0
0
512
1
0
1
1024
1
1
0
2048
1
1
1
4096
4.6
Offset Error
This is the error induced by the ADC when the inputs
are shorted together (VIN = 0V). The specification
incorporates both PGA and ADC offset contributions.
This error varies with PGA and OSR settings. The
offset is different on each channel and varies from chip
to chip. The offset is specified in µV. The offset error
can be digitally compensated independently on each
channel through the OFFCAL_CH0 register with a
24-bit calibration word.
It is the maximum remaining error after calibration of
offset and gain errors for a DC input signal.
Signal-to-Noise Ratio (SNR)
For the MCP3918 ADC, the signal-to-noise ratio is a
ratio of the output fundamental signal power to noise
power (not including the harmonics of the signal), when
the input is a sine wave at a predetermined frequency
(see Equation 4-4). It is measured in dB. Usually, only
the maximum signal-to-noise ratio is specified. The
SNR figure depends mainly on the OSR and DITHER
settings of the device.
EQUATION 4-4:
SIGNAL-TO-NOISE RATIO
SignalPower
SNR dB = 10 log ----------------------------------
NoisePower
4.10
Signal-to-Noise and Distortion
Ratio (SINAD)
The most important figure of merit for the analog
performance of the ADC present on the MCP3918 is
the
Signal-to-Noise
and
Distortion
(SINAD)
specification.
The offset on the MCP3918 has a low temperature
coefficient.
The Signal-to-Noise and Distortion ratio is similar to
signal-to-noise ratio, with the exception that you must
include the harmonics power in the noise power
calculation
(see
Equation 4-5).
The
SINAD
specification depends mainly on the OSR and DITHER
settings.
4.7
EQUATION 4-5:
Gain Error
This is the error induced by the ADC on the slope of the
transfer function. It is the deviation expressed in %,
compared to the ideal transfer function defined in
Equation 5-3. The specification incorporates both PGA
and ADC gain error contributions, but not the VREF
contribution (it is measured with an external VREF).
This error varies with PGA and OSR settings. The gain
error can be digitally compensated independently on
each channel through the GAINCAL_CH0 register with
a 24-bit calibration word.
The gain error on the MCP3918 has a low temperature
coefficient.
2014 Microchip Technology Inc.
SINAD EQUATION
SignalPower
SINAD dB = 10 log ---------------------------------------------------------------------
Noise + HarmonicsPower
The calculated combination of SNR and THD per the
following formula also yields SINAD (see Equation 46).
EQUATION 4-6:
SINAD, THD AND SNR
RELATIONSHIP
SINAD dB = 10 log 10
SNR
-
---------10
+ 10
THD
–
--------------10
DS20005287A-page 25
MCP3918
4.11
Total Harmonic Distortion (THD)
The total harmonic distortion is the ratio of the output
harmonics power to the fundamental signal power for a
sine wave input, and is defined in Equation 4-7.
EQUATION 4-7:
HarmonicsPower
THD dB = 10 log -----------------------------------------------------
FundamentalPower
The THD calculation includes the first 35 harmonics for
the MCP3918 specifications. The THD is usually only
measured with respect to the first ten harmonics. THD
is sometimes expressed as percentage. Equation 4-8
converts the THD in percentage.
EQUATION 4-8:
THD % = 100 10
THD dB
-----------------------20
This specification depends mainly on the DITHER
setting.
4.12
Spurious-Free Dynamic Range
(SFDR)
SFDR is the ratio between the output power of the
fundamental and the highest spur in the frequency
spectrum (see Equation 4-9). The spur frequency is not
necessarily a harmonic of the fundamental, even
though this is usually the case. This figure represents
the dynamic range of the ADC when a full-scale signal
is used at the input. This specification depends mainly
on the DITHER setting.
EQUATION 4-9:
FundamentalPower
SFDR dB = 10 log -----------------------------------------------------
HighestSpurPower
4.13
MCP3918 Delta-Sigma
Architecture
The MCP3918 incorporates one delta-sigma ADC with
a multi-bit architecture. A delta-sigma ADC is an
oversampling converter that incorporates a built-in
modulator, which digitizes the quantity of charges
integrated by the modulator loop (see Figure 5-1). The
quantizer is the block that performs the
analog-to-digital conversion. The quantizer is typically
1-bit, or a simple comparator, which helps maintain the
linearity performance of the ADC (the DAC structure is,
in this case, inherently linear).
DS20005287A-page 26
Multi-bit quantizers help lower the quantization error
(the error fed back in the loop can be very large with
1-bit quantizers) without changing the order of the
modulator or the OSR, which leads to better SNR
figures. However, typically, the linearity of such
architectures is more difficult to achieve since the DAC
linearity is as difficult to attain, and its linearity limits the
THD of such ADC.
The 5-level quantizer present in MCP3918 is a Flash
ADC composed of four comparators arranged with
equally spaced thresholds and a thermometer coding.
For improved THD figures, the MCP3918 also includes
proprietary 5-level DAC architecture that is inherently
linear.
4.14
Idle Tones
A delta-sigma converter is an integrating converter. It
also has a finite quantization step (LSB) which can be
detected by its quantizer. A DC input voltage that is
below the quantization step should only provide an
all zeros result, since the input is not large enough to
be detected. As an integrating device, any delta-sigma
ADC will show idle tones. This means that the output
will have spurs in the frequency content that depend on
the ratio between the quantization step voltage and the
input voltage. These spurs are the result of the
integrated sub-quantization step inputs that will
eventually cross the quantization steps after a long
enough integration. This will induce an AC frequency at
the output of the ADC, and can be shown in the ADC
output spectrum.
These idle tones are residues that are inherent to the
quantization process and to the fact that the converter
is integrating at all times without being reset. They are
residues of the finite resolution of the conversion
process. They are very difficult to attenuate and they
are heavily signal-dependent. They can degrade the
SFDR and THD of the converter, even for DC inputs.
They can be localized in the baseband of the converter
and are thus difficult to filter from the actual input signal.
For power metering applications, idle tones can be very
disturbing, because energy can be detected even at
the 50 or 60 Hz frequency, depending on the DC offset
of the ADC, while no power is really present at the
inputs. The only practical way to suppress or attenuate
the idle tones phenomenon is to apply dithering to the
ADC. The amplitudes of the idle tones are a function of
the order of the modulator, the OSR and the number of
levels in the quantizer of the modulator. A higher order,
a higher OSR, or a higher number of levels for the
quantizer will attenuate the amplitudes of the idle
tones.
2014 Microchip Technology Inc.
MCP3918
4.15
Dithering
In order to suppress or attenuate the idle tones present
in any delta-sigma ADC, dithering can be applied to the
ADC. Dithering is the process of adding an error to the
ADC feedback loop in order to “decorrelate” the outputs
and “break” the idle tone’s behavior. Usually a random
or pseudo-random generator adds an analog or digital
error to the feedback loop of the delta-sigma ADC in
order to ensure that no tonal behavior can happen at its
outputs. This error is filtered by the feedback loop and
typically has a zero average value, so that the
converter’s static transfer function is not disturbed by
the dithering process. However, the dithering process
slightly increases the noise floor (it adds noise to the
part) while reducing its tonal behavior and thus
improving SFDR and THD. The dithering process
scrambles the idle tones into baseband white noise and
ensures that dynamic specs (SNR, SINAD, THD,
SFDR) are less signal-dependent. The MCP3918
incorporates a proprietary dithering algorithm on the
ADC in order to remove idle tones and improve THD,
which is crucial for power metering applications.
4.16
PSRR
This is the ratio between a change in the power supply
voltage and the ADC output codes. It measures the
influence of the power supply voltage on the ADC
outputs.
The PSRR specification can be DC (the power supply
takes multiple DC values) or AC (the power supply is a
sine wave at a certain frequency with a certain
common-mode). In AC, the amplitude of the sine wave
represents the change in the power supply. It is defined
in Equation 4-10.
EQUATION 4-10:
V OUT
PSRR dB = 20 log -------------------
AVDD
Where VOUT is the equivalent input voltage that the
output code translates to, with the ADC transfer
function.
In the MCP3918 specification, AVDD varies from 2.7V
to 3.6V, and for AC PSRR a 50/60 Hz sine wave
centered around 3.0V is chosen, with a maximum
amplitude of 300 mV. The PSRR specification is
measured with AVDD = DVDD.
4.17
The CMRR specification can be DC (the
common-mode input voltage takes multiple DC values)
or AC (the common-mode input voltage is a sine wave
at a certain frequency with a certain common-mode). In
AC, the amplitude of the sine wave represents the
change in the power supply. It is defined in Equation 411.
EQUATION 4-11:
VOUT
CMRR dB = 20 log -----------------
VCM
Where VCM = (CH0+ + CH0-)/2 is the common-mode
input voltage and VOUT is the equivalent input voltage
that the output code translates to, with the ADC transfer
function. In the MCP3918 specification, VCM varies
from -1V to +1V.
4.18
ADC Reset Mode
ADC Reset mode (also called Soft Reset mode) can
only be entered in SPI mode by setting the RESET<0>
bit high in the CONFIG1 register. This mode is defined
as the condition where the converter is active, but its
output is forced to 0.
The registers are not affected in this Reset mode and
retain their state, except for the data registers of the
corresponding channel, which are reset to 0.
The ADC can immediately output meaningful codes
after leaving the Reset mode (and after the sinc filter
settling time). This mode is both entered and exited
through bit settings in CONFIG1 register.
The configuration registers are not modified by the Soft
Reset mode. While in Reset mode, no Data Ready
pulse will be generated by the ADC.
When the ADC exits ADC Reset mode, any phase
delay present before reset was entered will still be
present.
However, when the ADC is in Soft Reset mode, the
input structure is still clocking if MCLK is applied in
order to properly bias the inputs, so that no leakage
current is observed. If MCLK is not applied, large
analog input leakage currents can be observed for
highly negative input voltages (typically below -0.6V
referred to AGND).
CMRR
CMRR is the ratio between a change in the
common-mode input voltage and the ADC output
codes. It measures the influence of the common-mode
input voltage on the ADC outputs.
2014 Microchip Technology Inc.
DS20005287A-page 27
MCP3918
4.19
Hard Reset Mode (RESET = 0)
This mode is only available during a POR or when the
RESET pin is pulled low in the SPI mode. The RESET
pin logic-low state places the device in Hard Reset
mode. In this mode, all internal registers are reset to
their default state. In the 2-Wire Interface mode, the
RESET pin functionality is not available and the user
must use a watchdog timer reset to be able to fully reset
the part (see Section 7.4 “Watchdog Timer Reset,
Resetting the Part when in 2-Wire Mode”).
The DC biases for the analog blocks are still active, i.e.
the MCP3918 is ready to convert. However, this pin
clears all conversion data in the ADC. The
comparators’ outputs of the ADC are forced to their
Reset state (0011). The sinc filter as well as its double
output buffers are all reset. See serial timing for
minimum pulse low time in Section 1.0 “Electrical
Characteristics”. During a Hard Reset, no
communication with the part is possible. The digital
interface is maintained in a Reset state.
During this state, the clock MCLK can be applied to the
part in order to properly bias the input structures of all
channels. If not applied, large analog input leakage
currents can be observed for highly negative input
signals, and, after removing the Hard Reset state, a
certain start-up time is necessary to properly bias the
input structure. During this delay, the ADC conversions
can be inaccurate.
4.20
ADC Shutdown Mode
ADC Shutdown mode is defined as a state where the
converters and their biases are off, consuming only
leakage current. When the Shutdown bit is reset to ‘0’,
the analog biases will be enabled, as well as the clock
and the digital circuitry. The ADC will give a data ready
after the sinc filter settling time has occurred. However,
since the analog biases are not completely settled at
the beginning of the conversion, the sampling may not
be accurate for about 1 ms (corresponding to the
settling time of the biasing under worst-case
conditions). In order to ensure accuracy, the Data
Ready pulse within the delay of 1 ms + settling time of
the sinc filter should be discarded.
When the ADC exits ADC Shutdown mode, any phase
delay present before Shutdown was entered will still be
present.
If the ADC is in Shutdown mode, the clock is not
distributed to the input structure or to the digital core for
low-power operation. This can potentially cause high
analog input leakage currents at the analog inputs if the
input voltage is highly negative (typically below -0.6V
referred to AGND). Once the ADC is back to normal
operation, the clock is automatically distributed again.
4.21
Full Shutdown Mode
The lowest power consumption can be achieved when
SHUTDOWN<0> = 1, VREFEXT = CLKEXT = 1. This
mode is called Full Shutdown mode, and no analog
circuitry is enabled. In this mode, both AVDD and DVDD
POR monitoring are also disabled, and no clock is
propagated throughout the chip. The ADC is in
Shutdown mode, and the internal voltage reference is
disabled. This mode can only be entered during SPI
mode.
The clock is no longer distributed to the input structure
either. This can potentially cause high analog input
leakage currents at the analog inputs, if the input
voltage is highly negative (typically below -0.6V
referred to AGND).
The only circuit that remains active is the SPI interface,
but this circuit does not induce any static power
consumption. If SCK is idle, the only current
consumption comes from the leakage currents induced
by the transistors and is less than 5 µA on each power
supply.
This mode can be used to power down the chip
completely and to avoid power consumption when
there is no data to convert at the analog inputs. Any
SCK or MCLK edge occurring while in this mode will
induce dynamic power consumption.
Once any of the SHUTDOWN, CLKEXT and VREFEXT
bits returns to ‘0’, the two POR monitoring blocks are
operational, and AVDD and DVDD monitoring can take
place.
The configuration registers are not modified by the
Shutdown mode. This mode is only available in SPI
mode through programming the SHUTDOWN<1:0>
bits in the CONFIG1 register.
The output data is flushed to all zeros while in ADC
Shutdown mode. While in ADC Shutdown mode, no
Data Ready pulse will be generated by the ADC.
DS20005287A-page 28
2014 Microchip Technology Inc.
MCP3918
4.22
Measurement Error
The measurement error specification is typically used
in power metering applications. This specification is a
measurement of the linearity of the active energy of a
given power meter across its dynamic range.
Figure 2-5 shows the typical measurement error
curves obtained with the samples acquired by the
MCP3918, using the default settings with 1-point and
2-point calibration. These calibrations are detailed in
Section 8.6 “Energy Measurement Error Considerations”.
For this measurement, the goal is to measure the
active energy of one phase when the voltage Root
Mean Square (RMS) value is fixed, and the current
RMS value is sweeping across the dynamic range
specified by the meter. The measurement error is the
non-linearity error of the energy power across the
current dynamic range. It is expressed in percent (%).
Equation 4-12 shows the formula that calculates the
measurement error:
EQUATION 4-12:
Measured Active Energy – Active Energy present at inputs
Measurement Error I RMS = -------------------------------------------------------------------------------------------------------------------------------------------- 100%
Active Energy present at inputs
In the present device, the calculation of the active
energy is done externally, as a post-processing step
that typically happens in the microcontroller,
considering, for example, one ADC as current channel
and the other MCP3918 ADC as voltage channel. The
voltage channel is fed with a full-scale sine wave at
600 mV peak and is configured with GAIN = 1 and
DITHER = Maximum. To obtain the active energy
measurement error graphs, the current channel is fed
with sine waves with amplitudes that vary from 600 mV
peak to 60 µV peak, representing a 10,000:1 dynamic
range. The offset is removed on both current and
voltage channels, and the channels are multiplied
together to give instantaneous power. The active
energy is calculated by multiplying the current and
voltage channel, and averaging the results of this
power during 20 seconds, to extract the active energy.
The sampling frequency is chosen as a multiple integer
of line frequency (coherent sampling). Therefore, the
calculation does not take into account any residue
coming from bad synchronization.
The measurement error is a function of IRMS, varies
with the OSR, averaging time, MCLK frequency and is
tightly coupled with the noise and linearity
specifications. The measurement error is a function of
the linearity and THD of the ADC, while the standard
deviation of the measurement error is a function of the
noise specification of the ADC. Overall, the low THD
specification enables low measurement error on a very
large dynamic range (e.g. 10,000:1). A low noise and
high SNR specification enables the decrease of the
measurement time and, therefore, of the calibration
time, to obtain a reliable measurement error
specification.
2014 Microchip Technology Inc.
DS20005287A-page 29
MCP3918
NOTES:
DS20005287A-page 30
2014 Microchip Technology Inc.
MCP3918
5.0
DEVICE OVERVIEW
5.1
Analog Inputs (CH0+/-)
The MCP3918 analog inputs can be connected directly
to current and voltage transducers (such as shunts,
current transformers or Rogowski coils). Each input pin
is protected by specialized ESD structures that allow
bipolar ±2V continuous voltage, with respect to AGND,
to be present at their inputs without the risk of permanent damage.
The ADC has fully differential voltage inputs for better
noise performance. The absolute voltage at each pin
relative to AGND should be maintained in the ±1V range
during operation in order to ensure the specified ADC
accuracy. The common mode signals should be
adapted to respect both the previous conditions and
the differential input voltage range. For best
performance, the common mode signals should be
maintained to AGND.
Note:
5.2
If the analog inputs are held to a potential
of -0.6 to -1V for extended periods of time,
MCLK must be present inside the device
in order to avoid large leakage currents at
the analog inputs. This is true even during
Hard Reset mode or during the Soft Reset
of the ADC. However, during the
Shutdown mode of the ADC or during the
POR state, the clock is not distributed
inside the circuit. During these states, it is
recommended to keep the analog input
voltages above -0.6V referred to AGND in
order to avoid high analog inputs leakage
currents.
Programmable Gain Amplifiers
(PGA)
The Programmable Gain Amplifier (PGA) resides at the
front-end of the delta-sigma ADC. It has two functions:
translate the common-mode voltage of the input from
AGND to an internal level between AGND and AVDD, and
amplify the input differential signal. The translation of
the common-mode voltage does not change the
differential signal, but recenters the common mode so
that the input signal can be properly amplified.
The PGA block can be used to amplify very low signals,
but the differential input range of the delta-sigma
modulator must not be exceeded. The PGA of the ADC
is controlled by the PGA_CH0<2:0> bits in the GAIN
register. Table 5-1 displays the gain settings for the
PGA.
2014 Microchip Technology Inc.
TABLE 5-1:
PGA CONFIGURATION
SETTING
Gain
PGA_CH0<2:0>
Gain
(V/V)
Gain
(dB)
0
VIN Range (V)
0
0
0
1
±0.6
0
0
1
2
6
±0.3
0
1
0
4
12
±0.15
0
1
1
8
18
±0.075
1
0
0
16
24
±0.0375
1
0
1
32
30
±0.01875
Note: The two undefined settings are G = 1. This
table is defined with VREF = 1.2V.
5.3
Delta-Sigma Modulator
5.3.1
ARCHITECTURE
The ADC includes a proprietary second-order
modulator with a multi-bit 5-level DAC architecture (see
Figure 5-1). The quantizer is a Flash ADC composed of
four comparators with equally spaced thresholds and a
thermometer output coding. The proprietary five-level
architecture ensures minimum quantization noise at
the outputs of the modulators without disturbing
linearity or inducing additional distortion. The sampling
frequency is DMCLK (typically 1 MHz with
MCLK = 4 MHz) so the modulators are refreshed at a
DMCLK rate.
Figure 5-1 represents a simplified block diagram of the
delta-sigma ADC present on MCP3918.
Loop
Filter
Differential
Voltage Input
SecondOrder
Integrator
Quantizer
Output
5-level
Flash ADC
Bit Stream
DAC
MCP3918 Delta-Sigma Modulator
FIGURE 5-1:
Block Diagram.
Simplified Delta-Sigma ADC
DS20005287A-page 31
MCP3918
5.3.2
MODULATOR INPUT RANGE AND
SATURATION POINT
5.3.3
The delta-sigma modulator includes a programmable
biasing circuit, in order to further adjust the power
consumption to the sampling speed applied through
the MCLK. This can be programmed through the
BOOST<1:0> bits, which are applied to all channels
simultaneously.
For a specified voltage reference value of 1.2V, the
modulator specified differential input range is ±600 mV.
The input range is proportional to VREF and scales
according to the VREF voltage. This range ensures the
stability of the modulator over amplitude and frequency.
Outside this range, the modulator is still functional;
however, its stability is no longer ensured and therefore
it is not recommended to exceed this limit. The
saturation point for the modulator is VREF/1.5, since the
transfer function of the ADC includes a gain of 1.5 by
default (independent from the PGA setting). See
Section 5.5 “ADC Output Coding”.
TABLE 5-2:
The maximum achievable analog master clock speed
(AMCLK), the maximum sampling frequency (DMCLK)
and the maximum achievable data rate (DRCLK) highly
depend on the BOOST<1:0> and PGA_CH0<2:0>
settings. Table 5-2 specifies the maximum AMCLK
possible to keep optimal accuracy with respect to the
BOOST<1:0> and PGA_CH0<2:0> settings.
MAXIMUM AMCLK LIMITS AS A FUNCTION OF BOOST AND PGA GAIN
Conditions
Boost
BOOST SETTINGS
Gain
VDD = 3.0V to 3.6V,
TA from -40°C to +125°C
Maximum AMCLK
(MHz)
(SINAD within -3 dB
from its maximum)
Maximum AMCLK
(MHz)
(SINAD within -5 dB
from its maximum)
VDD = 2.7V to 3.6V,
TA from -40°C to +125°C
Maximum AMCLK
(MHz)
(SINAD within -3 dB
from its maximum)
Maximum AMCLK
(MHz)
(SINAD within -5 dB
from its maximum)
0.5x
1
4
4
4
4
0.66x
1
6.4
7.3
6.4
7.3
1x
1
11.4
11.4
10.6
10.6
2x
1
16
16
16
16
0.5x
2
4
4
4
4
0.66x
2
6.4
7.3
6.4
7.3
1x
2
11.4
11.4
10.6
10.6
2x
2
16
16
13.3
14.5
0.5x
4
2.9
2.9
2.9
2.9
0.66x
4
6.4
6.4
6.4
6.4
1x
4
10.7
10.7
9.4
10.7
2x
4
16
16
16
16
0.5x
8
2.9
4
2.9
4
0.66x
8
7.3
8
6.4
7.3
1x
8
11.4
12.3
8
8.9
2x
8
16
16
10
11.4
0.5x
16
2.9
2.9
2.9
2.9
0.66x
16
6.4
7.3
6.4
7.3
1x
16
11.4
11.4
9.4
10.6
2x
16
13.3
16
8.9
11.4
0.5x
32
2.9
2.9
2.9
2.9
0.66x
32
7.3
7.3
7.3
7.3
1x
32
10.6
12.3
9.4
10,6
2x
32
13.3
16
10
11.4
DS20005287A-page 32
2014 Microchip Technology Inc.
MCP3918
5.3.4
DITHER SETTINGS
The modulator includes a dithering algorithm that can
be enabled through the DITHER<1:0> bits in the
CONFIG0 register. This dithering process improves
THD and SFDR (for high OSR settings), while slightly
increasing the noise floor of the ADC. For power
metering applications and applications that are
distortion-sensitive, it is recommended to keep
DITHER at maximum settings for best THD and SFDR
performance. In the case of power metering
applications, THD and SFDR are critical specifications.
Optimizing SNR (noise floor) is not problematic due to
the large averaging factor at the output of the ADC.
Therefore, even for low OSR settings, the dithering
algorithm will show a positive impact on the
performance of the application.
5.3.5
TABLE 5-3:
DELTA-SIGMA MODULATOR
CODING
Comp<3:0>
Code
Modulator
Output Code
MDAT Serial
Stream
1111
+2
1111
0111
+1
0111
0011
0
0011
0001
-1
0001
0000
-2
0000
COMP COMP COMP COMP
<0>
<1>
<3>
<2>
AMCLK
MODULATOR OUTPUT BLOCK
If the user wishes to use the modulator output of the
device, the EN_MDAT bit in the STATUSCOM register
must be set to enable.
DMCLK
When the EN_MDAT bit is enabled, the modulator
output is present at the MDAT0 output pin as soon as
the command is placed. Additionally, the corresponding
sinc filter is disabled in order to consume less current.
The corresponding Data Ready pulse is not present
either at the DR output pin. When the EN_MDAT bit is
cleared, the sinc filter is back to normal operation and
the MDAT0 output is high-impedance. The data ready
output pin is then placed in high-impedance regardless
of the DR_HIZ setting, so that the user can tie this pin
to an external supply or ground for lower noise
behavior.
MDAT+2
Since the delta-sigma modulator has a five-level output
given by the state of the four comparators with
thermometer coding, its output can be represented on
four bits, each bit giving the state of the corresponding
comparator (see Table 5-3). These bits are present in
the MOD register and are updated at the DMCLK rate.
MDAT-2
In order to output the result of the comparator on a
separate pin (MDAT0), this comparator output bit has
been arranged to be serially output at the AMCLK rate
(see Figure 5-2).
This 1-bit serial bit stream is the same that would be
produced by a 1-bit DAC modulator with a sampling
frequency of AMCLK. The modulator can either be
considered as a five-level output at DMCLK rate or a
1-bit output at AMCLK rate. These two representations
are interchangeable. The MDAT0 output can therefore
be used in any application that requires 1-bit modulator
outputs. Such applications will often integrate and filter
the 1-bit output with sinc or more complex decimation
filters computed by a MCU or a DSP.
2014 Microchip Technology Inc.
MDAT+1
MDAT+0
MDAT-1
FIGURE 5-2:
MDAT0 Serial Output with
Respect to the Modulator Output Code.
Since the Reset and Shutdown SPI commands are
asynchronous, the MDAT0 pin is resynchronized with
DMCLK after each time the part goes out of reset and
shutdown.
This means that, after a soft reset or a shutdown, the
first output of MDAT0 is always 0011 after the first
DMCLK rising edge.
The MDAT0 output pin is high-impedance if the RESET
pin is low and in 2-wire interface mode.
DS20005287A-page 33
MCP3918
5.4
SINC3 + SINC1 Filter
The decimation filter present in the MCP3918 is a
cascade of two sinc filters (SINC3 + SINC1): a
third-order sinc filter with a decimation ratio of OSR3,
followed by a first-order sinc filter with a decimation
ratio of OSR1 (moving average of OSR1 values).
Figure 5-3 represents the decimation filter architecture.
OSR1 = 1
Modulator
Output
SINC3
SINC1
4
Decimation Filter
Output
16 (WIDTH = 0)
24 (WIDTH = 1)
OSR3
OSR1
Decimation Filter
FIGURE 5-3:
MCP3918 Decimation Filter Block Diagram.
Equation 5-1 calculates the filter z-domain transfer
function.
EQUATION 5-1:
SINC FILTER TRANSFER
FUNCTION
- OSR 1 OSR 3
- OSR 3 3
1 – z
1 – z
H z = ---------------------------------------------- --------------------------------------------------------3
–
1
OSR
OSR 1 – z
3
3
OSR 1 – z
1
Where z = EXP 2 j f in DMCLK
Equation 5-2 calculates the settling time of the ADC as
a function of DMCLK periods.
EQUATION 5-2:
SettlingTime DMCLKperiods = 3 OSR + OSR – 1 OSR
3
1
3
The SINC1 filter following the SINC3 filter is only
enabled for the high OSR settings. This SINC1 filter
provides additional rejection at a low cost with little
modification to the -3 dB bandwidth. The resolution
(number of significant bits) of the digital filter is 24-bit
maximum for any OSR and data format choice. The
resolution depends only on the OSR<2:0> settings in
the CONFIG0 register per Table 5-4. Once the OSR is
chosen, the resolution is fixed and the output code
respects the data format defined by the
WIDTH_DATA<1:0> setting in the STATUSCOM
register (see Section 5.5 “ADC Output Coding”).
keep the desired accuracy over the baseband of the
converter. This anti-aliasing filter can be a simple,
first-order RC network, with a sufficiently low time
constant to generate high rejection at the DMCLK
frequency.
Any unsettled data is automatically discarded to avoid
data corruption. Each Data Ready pulse corresponds
to fully settled data at the output of the decimation filter.
The first data available at the output of the decimation
filter is present after the complete settling time of the
filter (see Table 5-4). After the first data has been
processed, the delay between two Data Ready pulses
is one DRCLK period. The data stream from input to
output is delayed by an amount equal to the settling
time of the filter (which is the group delay of the filter).
The resolution achievable, the -3 dB bandwidth and the
settling time at the output of the decimation filter (the
output of the ADC) are dependent on the OSR of each
sinc filter and are summarized in Table 5-4.
The gain of the transfer function of this filter is 1 at each
multiple of DMCLK (typically 1 MHz), so a proper antialiasing filter must be placed at the inputs. This will
attenuate the frequency content around DMCLK and
DS20005287A-page 34
2014 Microchip Technology Inc.
MCP3918
TABLE 5-4:
OVERSAMPLING RATIO AND SINC FILTER SETTLING TIME
OSR<2:0>
OSR3
OSR1
Total OSR
Resolution in Bits
(No Missing Code)
Settling Time
-3 dB Bandwidth
32
1
32
17
96/DMCLK
0.26*DRCLK
0
0
0
0
0
1
64
1
64
20
192/DMCLK
0.26*DRCLK
0
1
0
128
1
128
23
384/DMCLK
0.26*DRCLK
0
1
1
256
1
256
24
768/DMCLK
0.26*DRCLK
1
0
0
512
1
512
24
1536/DMCLK
0.26*DRCLK
1
0
1
512
2
1024
24
2048/DMCLK
0.37*DRCLK
1
1
0
512
4
2048
24
3072/DMCLK
0.42*DRCLK
1
1
1
512
8
4096
24
5120/DMCLK
0.43*DRCLK
5.5
0
The second-order modulator, SINC3+SINC1 filter,
PGA, VREF and the analog input structure all work
together to produce the device transfer function for the
analog-to-digital conversion (see Equation 5-3).
Ma
agnitude (dB)
-20
-40
-60
-80
-100
-120
1
10
100
1000
10000
100000
Input Frequency (Hz)
FIGURE 5-4:
Sinc Filter Frequency
Response, OSR = 256, MCLK = 4 MHz,
PRE<1:0> = 00.
0
The output data is calculated on 24-bit (23-bit plus sign)
and coded in two's complement format, MSB first. The
output format can then be modified by the
WIDTH_DATA<1:0> settings in the STATUSCOM
register to allow 16-, 24- or 32-bit formats compatibility
(see Section 9.5 “STATUSCOM Register - Status
and Communication Register” for more information).
In case of positive saturation (CH0+ – CH0> VREF/1.5), the output code is locked to 7FFFFF for
24-bit mode. In case of negative saturation
(CH0+ - CH0- < -VREF/1.5), the output code is locked
to 800000 for 24-bit mode.
Equation 5-3 is only true for DC inputs. For AC inputs,
this transfer function needs to be multiplied by the
transfer function of the SINC3+SINC1 filter (see
Equations 5-1 and 5-3).
-20
Magnitude (dB)
ADC Output Coding
-40
-60
-80
EQUATION 5-3:
-100
CH n+ – CH nDATA_CH0 = ------------------------------------- 8 388 608 G 1.5
V REF+ – V REF-
-120
-140
-160
For 24-bit Mode, WIDTH_DATA<1:0> = 01 (Default)
1
100
10000
Input Frequency (Hz)
1000000
FIGURE 5-5:
Sinc Filter Frequency
Response, OSR = 4096 (in pink), OSR = 512 (in
blue), MCLK = 4 MHz, PRE<1:0> = 00.
2014 Microchip Technology Inc.
For data formats other than the default 24-bit format,
Equation 5-3 should be multiplied by a scaling factor,
depending on the data format used (defined by
WIDTH_DATA<1:0>). The data format and the
associated scaling factors are given in Figure 5-6.
DS20005287A-page 35
MCP3918
23
0
Scaling
Factor
DATA DATA DATA
<23:16> <15:8> <7:0>
15
WIDTH_DATA<1:0> = 00
16-bit
0
DATA DATA
<23:16> <15:8>
DATA
<7>
Unformatted ADC data
x1/256
Rounded
WIDTH_DATA<1:0> = 01
24-bit
23
WIDTH_DATA<1:0> = 10
32-bit with zeros padded
31
x1
0
DATA DATA DATA
<23:16> <15:8> <7:0>
31
WIDTH_DATA<1:0> = 11
32-bit with sign extension
FIGURE 5-6:
0
DATA DATA DATA
<23:16> <15:8> <7:0>
0x00
x256
0
DATA DATA DATA DATA
<23> <23:16> <15:8> <7:0>
x1
Output Data Formats.
The ADC resolution is a function of the OSR
(Section 5.4 “SINC3 + SINC1 Filter”). The resolution
is the same for all channels. No matter what the
resolution is, the ADC output data is always calculated
in 24-bit words, with added zeros at the end if the OSR
is not large enough to produce 24-bit resolution (left
justification).
TABLE 5-5:
OSR = 256 (AND HIGHER) OUTPUT CODE EXAMPLES
ADC Output Code (MSB First)
0
0
0
1
1
1
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
TABLE 5-6:
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
0
0
1
1
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
TABLE 5-7:
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
0
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
0
0
1
1
0
0
0
0
0
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
0x7FFFFF
0x7FFFFE
0x000000
0xFFFFFF
0x800001
0x800000
+ 8,388,607
+ 8,388,606
0
-1
- 8,388,607
- 8,388,608
Hexadecimal
Decimal,
23-bit Resolution
0x7FFFFE
0x7FFFFC
0x000000
0xFFFFFE
0x800002
0x800000
+ 4,194,303
+ 4,194,302
0
-1
- 4,194,303
- 4,194,304
Hexadecimal
Decimal,
20-bit Resolution
0x7FFFF0
0x7FFFE0
0x000000
0xFFFFF0
0x800010
0x800000
+ 524, 287
+ 524, 286
0
-1
- 524,287
- 524, 288
OSR = 64 OUTPUT CODE EXAMPLES
ADC Output Code (MSB First)
0
0
0
1
1
1
Decimal,
24-bit Resolution
OSR = 128 OUTPUT CODE EXAMPLES
ADC Output Code (MSB First)
0
0
0
1
1
1
Hexadecimal
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
DS20005287A-page 36
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
2014 Microchip Technology Inc.
MCP3918
TABLE 5-8:
OSR = 32 OUTPUT CODE EXAMPLES
ADC Output Code (MSB First)
0
0
0
1
1
1
1
1
0
1
0
0
5.6
5.6.1
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
1
0
1
0
0
1
0
0
1
1
0
Voltage Reference
INTERNAL VOLTAGE REFERENCE
The MCP3918 contains an internal voltage reference
source specially designed to minimize drift over
temperature. In order to enable the internal voltage
reference, the VREFEXT bit in the CONFIG1 register
must be set to ‘0’ (default mode). This internal VREF
supplies reference voltage to all channels. The typical
value of this voltage reference is 1.2V ± 2%. The
internal reference has a very low typical temperature
coefficient of ±7 ppm/°C, allowing the output to have
minimal variation, with respect to temperature, since
they are proportional to (1/VREF).
The noise of the internal voltage reference is low
enough not to significantly degrade the SNR of the
ADC, if compared to a precision external low-noise
voltage reference. The output pin for the internal
voltage reference is REFIN+/OUT.
If the voltage reference is only used as an internal
VREF, adding bypass capacitance on REFIN+/OUT is
not necessary for keeping ADC accuracy, but a minimal
0.1 µF ceramic capacitance can be connected to avoid
EMI/EMC susceptibility issues due to the antenna
created by the REFIN+/OUT pin, if left floating.
The bypass capacitors also help in applications where
the voltage reference output is connected to other
circuits. In this case, additional buffering may be
needed, since the output drive capability of this output
is low.
Adding too much capacitance on the REFIN+/OUT pin
may slightly degrade the THD performance of the ADC.
2014 Microchip Technology Inc.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
5.6.2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Hexadecimal
Decimal,
17-bit Resolution
0x7FFF80
0x7FFF00
0x000000
0xFFFF80
0x800080
0x800000
+ 65, 535
+ 65, 534
0
-1
- 65,535
- 65, 536
DIFFERENTIAL EXTERNAL
VOLTAGE INPUTS
When the VREFEXT bit is set to ‘1’, the two reference
pins (REFIN+/OUT, REFIN-) become a differential
voltage reference input. The voltage at the
REFIN+/OUT is noted VREF+, and the voltage at the
REFIN- pin is noted VREF-. The differential voltage
input value is given by Equation 5-4.
EQUATION 5-4:
VREF = VREF+ – VREFThe specified VREF ranges from 1.1V to 1.3V. The
REFIN- pin voltage (VREF-) should be limited to ±0.1V,
with respect to AGND. Typically, for single-ended
reference applications, the REFIN- pin should be
directly connected to AGND, with its own separate track
to avoid any spike due to switching noise.
5.6.3
TEMPERATURE COMPENSATION
(VREFCAL<7:0>)
The internal voltage reference consists of a proprietary
circuit and algorithm to compensate for first-order and
second-order
temperature
coefficients.
The
compensation enables very low temperature
coefficients (typically 9 ppm/°C) on the entire range of
temperatures, from - 40°C to +125°C. This temperature
coefficient varies from part to part.
This temperature coefficient can be adjusted on each
part through the VREFCAL<7:0> bits present in the
CONFIG0 register (bits 7 to 0). These register settings
are only for advanced users. The VREFCAL<7:0> bits
should not be modified unless the user wants to
calibrate the temperature coefficient of the whole
system or application. The default value of this register
is set to 0x50. The default value (0x50) was chosen to
optimize the standard deviation of the tempco across
process variation. The value can be slightly improved
to around 7 ppm/°C if the VREFCAL<7:0> bits are
written at 0x42, but this setting degrades the standard
deviation of the VREF tempco.The typical variation of
the temperature coefficient of the internal voltage
reference with respect to the VREFCAL register code
is given by Figure 5-6. Modifying the value stored in the
VREFCAL<7:0> bits may also vary the voltage
reference, in addition to the temperature coefficient.
DS20005287A-page 37
MCP3918
5.7
60
The MCP3918 contains an internal POR circuit that
monitors both analog and digital supply voltages during
operation. The typical threshold for a power-up event
detection is 2.0V ± 5% and a typical start-up time
(tPOR) of 50 µs. The POR circuit has a built-in
hysteresis for improved transient spike immunity that
has a typical value of 200 mV. Proper decoupling
capacitors (0.1 µF ceramic and 10 µF) should be
mounted as close as possible to the AVDD and DVDD
pins, providing additional transient immunity.
VREF Drift (ppm)
50
40
30
20
10
0
0
64
128
192
VREFCAL Register Trim Code (Decimal)
FIGURE 5-7:
Trim Code Chart.
5.6.4
Power-on Reset
256
Figure 5-8 illustrates the different conditions at a
power-up and a power-down event under typical
conditions. All internal DC biases are settled at least
1 ms after system POR, under worst-case conditions.
In order to ensure proper accuracy, any Data Ready
pulse occurring within 1 ms plus the sinc filter settling
time after system reset should be ignored. After POR,
Data Ready pulses are present at the pin with all the
default conditions in the configuration registers.
VREF Tempco vs. VREFCAL
VOLTAGE REFERENCE BUFFER
The MCP3918 ADC includes a voltage reference buffer
tied to the REFIN+/OUT pin, which allows the device to
properly charge the internal capacitors with the voltage
reference signals, even in the case of an external
voltage reference connection with weak load regulation
specifications. This ensures that the correct amount of
current is sourced to each channel to guarantee their
accuracy specifications, and diminishes the constraints
on the voltage reference load regulation.
Both AVDD and DVDD are monitored, so either power
supply can sequence first.
Voltage
(AVDD, DVDD)
Any Data Ready pulse
occurring during this time
can yield inaccurate output
data. It is recommended to
discard them.
POR Threshold
up (2.0V typical)
(1.8V typical)
tPOR Analog biases SINC
SINC filter
filter
settling time
POR
State
settling
settling
time
Power-Up
Normal
Operation
POR
State
Time
Biases are settled.
Biases are
Conversions started
unsettled.
here are accurate.
Conversions
started here may
not be accurate.
FIGURE 5-8:
DS20005287A-page 38
Power-On Reset Operation.
2014 Microchip Technology Inc.
MCP3918
5.8
Hard Reset Effect on Delta-Sigma
Modulator/Sinc Filter
In SPI mode, when the RESET pin is logic low, the ADC
will be in Reset and the output code is 0x0000h. The
RESET pin performs a hard reset (DC biases are still
on, part is ready to convert) and clears all charges
contained in the delta-sigma modulator. The
comparator’s output is ‘0011’ for the ADC.
The sinc filter is reset, as well as its double output
buffers. This pin is independent of the serial interface.
It brings all the registers to the default state. When
RESET is logic low, any write with the SPI interface will
be disabled and will have no effect. All output pins
(SDO, DR) are high-impedance.
If MCLK is applied, the input structure is enabled and is
properly biasing the substrate of the input transistors.
In this case, the leakage current on the analog inputs is
low if the analog input voltages are kept between -1V
and +1V.
If MCLK is not applied when in Reset mode, the
leakage can be high if the analog inputs are
below -0.6V, as referred to AGND.
5.9
Phase Delay Block
The MCP3918 incorporates a phase delay generator
which ensures the ADC (CH0) converts the inputs after
a fixed delay, as determined by the PHASE register
setting.
The PHASE register contains a 12-bit bank that
represents group delay of the ADC channel (in addition
to the settling time of the sinc filter) expressed in
DMCLK periods with an offset of OSR/2 periods. It is
coded with a 11-bit plus sign, MSB-first two's
complement code. This code indicates how many
DMCLK periods are induced as a delay (see
Equation 5-5).
EQUATION 5-5:
OSR
PHASE<11:0> Decimal Code + ----------2
Total Delay = -------------------------------------------------------------------------------------------DMCLK
The timing resolution of the phase delay is 1/DMCLK or
1 µs in the default configuration with MCLK = 4 MHz.
Given the definition of DMCLK, the phase delay is
affected by a change in the prescaler settings
(PRE<1:0>) and the MCLK frequency. The Data Ready
signal is affected by the phase delay settings.
2014 Microchip Technology Inc.
5.9.1
PHASE DELAY LIMITS
The limits of the phase delays are determined by the
OSR settings: the phase delays can only go from 0 to
+(OSR-1) DMCLK periods when taking the last reset as
a reference (same definition as MCP391X but not
showing an odd channel reference here since there is
only one channel).
If larger delays are needed, they can be implemented
externally to the chip with an MCU. A FIFO in the MCU
can save incoming data from the ADC channel for a
number N of DRCLK clocks. In this case, DRCLK
would represent the coarse timing resolution, and
DMCLK the fine timing resolution. The total delay will
then be equal to:
EQUATION 5-6:
Total Delay = N/DRCLK + OSR/2/DMCLK
Note:
Rewriting the PHASE register with the
same value automatically resets and
restarts the ADC.
The Phase delay register can be programmed once
with the OSR = 4096 setting, and will automatically
adjust the OSR afterwards, without the need to change
the value of the PHASE register.
• OSR = 4096: The delay can go from 0 to +4095.
PHASE<11> is the sign bit. Phase<10> is the
MSB and PHASE<0> the LSB.
• OSR = 2048: The delay can go from 0 to +2047.
PHASE<10> is the sign bit. Phase<9> is the MSB
and PHASE<0> the LSB.
• OSR = 1024: The delay can go from 0 to +1023.
PHASE<9> is the sign bit. Phase<8> is the MSB
and PHASE<0> the LSB.
• OSR = 512: The delay can go from 0 to +511
PHASE<8> is the sign bit. Phase<7> is the MSB
and PHASE<0> the LSB.
• OSR = 256: The delay can go from 0 to +255.
PHASE<7> is the sign bit. Phase<6> is the MSB
and PHASE<0> the LSB.
• OSR = 128: The delay can go from 0 to +127.
PHASE<6> is the sign bit. Phase<5> is the MSB
and PHASE<0> the LSB.
• OSR = 64: The delay can go from 0 to +63.
PHASE<5> is the sign bit. Phase<4> is the MSB
and PHASE<0> the LSB.
• OSR = 32: The delay can go from 0 to +31.
PHASE<4> is the sign bit. Phase<3> is the MSB
and PHASE<0> the LSB.
DS20005287A-page 39
MCP3918
TABLE 5-9:
PHASE VALUES WITH
MCLK = 4 MHZ, OSR = 4096,
PRE<1:0> = 00
PHASE<11:0>
Hex
Delay
0 1 1 1 1 1 1 1 1 1 1 1 0x7FF
4095 µs
0 1 1 1 1 1 1 1 1 1 1 0 0x7FE
4094 µs
0 0 0 0 0 0 0 0 0 0 0 1 0x001
2049 µs
0 0 0 0 0 0 0 0 0 0 0 0 0x000
2048 µs
1 1 1 1 1 1 1 1 1 1 1 1 0xFFF
2047 µs
1 0 0 0 0 0 0 0 0 0 0 1 0x801
1 µs
1 0 0 0 0 0 0 0 0 0 0 0 0x800
0 µs
5.10
5.11
Crystal Oscillator
The MCP3918 includes a Pierce-type crystal oscillator
with very high stability and ensures very low tempco
and jitter for the clock generation. This oscillator can
handle crystal frequencies up to 20 MHz, provided that
proper load capacitances and quartz quality factor are
used. The crystal oscillator is enabled when
CLKEXT = 0 in the CONFIG1 register, therefore it
cannot be enabled during the 2-Wire Interface mode. It
is only selectable in the SPI Mode.
For a proper start-up, the load capacitors of the crystal
should be connected between OSC1 and DGND and
between OSC2 and DGND. They should also respect
Equation 5-7.
Data Ready Status Bit
In addition to the DR pin indicator, the MCP3918 device
includes a separate Data Ready status bit. The ADC
channel is associated to the corresponding
DRSTATUS bit that can be read at all times in the
STATUSCOM register. This status bit can be used to
synchronize the data retrieval, in case the DR pin is not
connected (see Section 6.8 “ADC Channel Latching
and Synchronization”).
The DRSTATUS bit is not writable; writing on it has no
effect. It has a default value of '1', which indicates that
the data of the corresponding ADC is not ready. This
means that the ADC output register has not been
updated since the last reading (or since the last reset).
The DRSTATUS bit takes the '0' state, once the ADC
channel register is updated (which happens at a
DRCLK rate). A simple read of the STATUSCOM
register clears the DRSTATUS bit to its default value
('1').
EQUATION 5-7:
2
6
1
R M < 1.6 10 -------------------------
f C LOAD
Where:
f = crystal frequency in MHz
CLOAD = load capacitance in pF, including
parasitics from the PCB
RM = motional resistance of the quartz, in
ohms
When CLKEXT = 1, the crystal oscillator is bypassed
by a digital buffer, to allow direct clock input for an
external clock (see Figure 4-1). In this case, OSC2
becomes the MODE select input pin for the Interface
mode. When MODE = 0, the digital interface stays in
SPI mode; when MODE = 1, the digital interface
toggles to the 2-Wire mode. A pull-down current forces
the MODE to be logic low (SPI mode) by default if the
OSC2 pin is floating.
For proper operation, the external clock should not be
higher
than
20 MHz
before
prescaling
(MCLK < 20 MHz).
Note:
DS20005287A-page 40
In addition to the conditions defining the
maximum MCLK input frequency range,
the AMCLK frequency should be
maintained inferior to the maximum limits
defined in Table 5-2, to ensure the
accuracy of the ADC. If these limits are
exceeded, it is recommended to choose
either a larger OSR or a larger prescaler
value so that AMCLK can respect these
limits.
2014 Microchip Technology Inc.
MCP3918
5.12
Digital System Offset and Gain
Errors
The MCP3918 incorporates two sets of additional
registers to perform system digital offset and gain error
calibration, which will modify the output result of the
channel, if calibration is enabled. The gain and offset
calibrations can be enabled or disabled through two
configuration bits (EN_OFFCAL and EN_GAINCAL).
When both calibrations are enabled, the output of the
ADC is modified per Equation 5-8. These calibrations
are not effective in 2-Wire interface mode.
EQUATION 5-8:
DIGITAL OFFSET AND GAIN ERROR CALIBRATION REGISTERS
CALCULATIONS
DATA_CH0 post – cal = DATA_CH0 pre – cal + OFFCAL_CH0 1 + GAINCAL_CH0
5.12.1
DIGITAL OFFSET ERROR
CALIBRATION
The OFFCAL_CH0 register is 23-bit plus sign two’s
complement registers, whose LSB value is the same as
the Channel ADC Data. This register is then added bit
by bit to the ADC output codes, if the EN_OFFCAL bit
is enabled. Enabling the EN_OFFCAL bit does not
create a pipeline delay; the offset addition is
instantaneous. For low OSR values, only the significant
digits are added to the output (up to the resolution of
the ADC; for example, at OSR = 32, only the first 17
bits are added).
The offset is not added when the corresponding
channel is in Reset or Shutdown mode. The
corresponding input voltage offset value added by each
LSB in these 24-bit registers is:
EQUATION 5-9:
OFFSET(1LSB) = VREF/(PGA_CHn x 1.5 x 8388608)
This register is a “Don't Care” if EN_OFFCAL = 0
(offset calibration disabled), but its value is not cleared
by the EN_OFFCAL bit.
5.12.2
DIGITAL GAIN ERROR
CALIBRATION
This register is a signed 24-bit MSB – first register
coded with a range of -1x to +(1 - 2-23)x (from
0x800000 to 0x7FFFFF). The gain calibration adds 1x
to this register and multiplies it to the output code of the
channel bit by bit, after offset calibration. Thus, the gain
calibration ranges from 0x to 1.9999999x (from
0x80000 to 0x7FFFFF). The LSB corresponds to a 2-23
increment in the multiplier.
Enabling EN_GAINCAL creates a pipeline delay of
24 DMCLK periods on all channels. All Data Ready
pulses are delayed by 24 DMCLK periods, starting
from data ready pulse following the command enabling
EN_GAINCAL bit. The gain calibration is effective on
the next data ready pulse following the command
enabling EN_GAINCAL bit.
The digital gain calibration does not function when the
corresponding channel is in Reset or Shutdown mode.
The gain multiplier value for an LSB in this 24-bit
register is:
EQUATION 5-10:
GAIN (1LSB) = 1/8388608
This register is a “Don't Care” if EN_GAINCAL = 0
(offset calibration disabled), but its value is not cleared
by the EN_GAINCAL bit.
The output data is kept to either 7FFF or 8000 (16-bit
mode) or 7FFFFF or 800000 (24-bit mode) if the output
results are out of bounds after all calibrations are
performed.
2014 Microchip Technology Inc.
DS20005287A-page 41
MCP3918
NOTES:
DS20005287A-page 42
2014 Microchip Technology Inc.
MCP3918
6.0
SPI SERIAL INTERFACE
DESCRIPTION
6.1
Overview
The MCP3918 device includes a four-wire (CS, SCK,
SDI, SDO) digital serial interface that is compatible with
SPI Modes 0,0 and 1,1. Data is clocked out of the
MCP3918 on the falling edge of SCK, and data is
clocked into the MCP3918 on the rising edge of SCK.
In these modes, the SCK clock can idle either high (1,1)
or low (0,0). The digital interface is asynchronous with
the MCLK clock that controls the ADC sampling and
digital filtering. All the digital input pins are
Schmitt-triggered to avoid system noise perturbations
on the communications.
Each independent SPI communication starts with a CS
falling edge and stops with the CS rising edge. When
CS is logic high, SDO is in high-impedance, there are
transitions on SCK, and SDI has no effect. Changing
from an SPI Mode 1,1 to an SPI Mode 0,0 and vice
versa is possible and can be done while the CS pin is
logic high. Any CS rising edge clears the
communication and resets the SPI digital interface.
Additional control pins (RESET, DR) are also provided
on separate pins for advanced communication
features. The Data Ready pin (DR) outputs pulses
when a new ADC channel data is available for reading,
which can be used as an interrupt for an MCU. The
master reset pin (RESET) acts like a hard reset and
can reset the part to its default power-up configuration
(equivalent to a POR state).
The MCP3918 interface has a simple command
structure. Every command is either a Read command
from a register or a Write command to a register. The
MCP3918 device includes nine registers defined in the
register map in Table 9-1. The register map is fully
compatible with the MCP391X family to allow easy
porting of MCU code from one design to another inside
the MCP391X family. The first byte (8-bit wide)
transmitted is always the Control byte that defines the
address of the register and the type of command (Read
or Write). It is followed by the register itself, which can
be in a 16-, 24- or 32-bit format, depending on the
multiple format settings defined in the STATUSCOM
register. The MCP3918 is compatible with multiple
formats that help reduce overhead in the data handling
for most MCUs and processors available on the market
(8-, 16- or 32-bit MCUs) and improve MCU-code
compaction and efficiency.
2014 Microchip Technology Inc.
The MCP3918 digital interface is capable of handling
various continuous read and write modes, which allow
the device to perform ADC data streaming or full
register map writing within only one communication
(and therefore with only one unique Control byte). The
internal registers can be grouped together with various
configurations through the READ<1:0> and WRITE
bits. The internal address counter of the serial interface
can be automatically incremented with no additional
Control byte needed, in order to loop through the
various groups of registers within the register map. The
groups are defined in Table 9-2.
The MCP3918 device also includes advanced security
features to secure each communication, to avoid
processing unwanted write commands in order to
change the desired configuration, and to alert the user
in case of a change in the desired configuration.
Each SPI read communication can be secured through
a selectable CRC-16 checksum provided on the SDO
pin at the end of every communication sequence. This
CRC-16 computation is compatible with the DMA CRC
hardware of the PIC24 and PIC32 MCUs, resulting in
no additional overhead for added security.
In order to secure the entire configuration of the device,
the MCP3918 includes an 8-bit lock code
(LOCK<7:0>), which blocks all write commands to the
full register map if the value of the LOCK<7:0> is not
equal to a defined password (0xA5). The user can
protect its configuration by changing the LOCK<7:0>
value to 0x00 after the full programming, so that no
unwanted write command will result in a change in the
configuration (because LOCK<7:0> is different from
the 0xA5 password).
An additional CRC-16 calculation is also running
continuously in the background to ensure the integrity
of the full register map. All writable registers of the
register map (except for the MOD register) are
processed through a CRC-16 calculation engine and
give a CRC-16 checksum that depends on the
configuration. This checksum is readable on the
LOCK/CRC register and updated at all times. If a
change in this checksum occurs, a selectable interrupt
can give a flag on the DR pin (the DR pin becomes logic
low) to warn the user that the configuration is
corrupted.
DS20005287A-page 43
MCP3918
6.2
Control Byte
6.3
The Control byte of the MCP3918 contains two device
Address bits (A<6:5>), five register Address bits
(A<4:0>) and a Read/Write bit (R/W). The first byte
transmitted to the MCP3918 in any communication is
always the Control byte. During the Control byte
transfer, the SDO pin is always in a high-impedance
state. The MCP3918 interface is device addressable
(through A<6:5>), so that multiple chips can be present
on the same SPI bus with no data bus contention, even
if they use the same CS pin and a provided half-duplex
SPI interface, with a different address identifier. This
functionality enables, for example, a Serial EEPROM
like 24AAXXX/24LCXXX or 24FCXXX. Moreover, it
enables the MCP3918 to share all the SPI pins and to
consume less I/O pins in the application processor,
since all these Serial EEPROM circuits use
A<6:5> = 00.
Reading from the Device
The first register read on the SDO pin is the one defined
by the address (A<4:0>) given in the Control byte. After
this first register is fully transmitted, if the CS pin is
maintained logic low, the communication continues
without an additional Control byte and the SDO pin
transmits another register with the address
automatically incremented.
Four different read mode configurations can be defined
through the READ<1:0> bits in the STATUSCOM
register for the address increment (see Section 6.5
“Continuous Communications, Looping on
Register Sets” and Table 9-2). The data on SDO is
clocked out of the MCP3918 on the falling edge of
SCK. The reading format for each register is defined in
Section 5.5 “ADC Output Coding”.
A<6> A<5> A<4> A<3> A<2> A<1> A<0> R/W
Device
Address
Register Address
FIGURE 6-1:
Read/
Write
Control Byte.
The default device address bits are A<6:5> = 01
(contact the Microchip factory for other available device
address bits). For more information, see the Product
Identification System section. The register map is
defined in Table 9-1.
CS
Device latches SDI on rising edge
Device latches SDO on falling edge
DATA<1>
DATA<2>
DATA<3>
DATA<4>
DATA<5>
DATA<6>
DATA<7>
DATA<8>
DATA<9>
DATA<10>
DATA<11>
DATA<12>
DATA<13>
DATA<14>
DATA<15>
DATA<16>
DATA<17>
DATA<18>
DATA<19>
DATA<20>
DATA<21>
DATA<22>
High
Hi-Z Z
A<0>
A<1>
A<2>
A<3>
Don’t care
R/W
DATA<23>
SDO
A<4>
Don’t care
A<5>
SDI
A<6>
SCK
DATA<0>
High
Hi-ZZ
READ Communication (SPI mode 1,1)
FIGURE 6-2:
SPI Mode 1,1).
DS20005287A-page 44
Read on a Single Register with 24-bit Format (WIDTH_DATA<1:0> = 01,
2014 Microchip Technology Inc.
MCP3918
CS
Device latches SDI on rising edge
Device latches SDO on falling edge
R/W
DATA<0>
DATA<1>
DATA<2>
DATA<3>
DATA<4>
DATA<5>
DATA<6>
DATA<7>
DATA<8>
DATA<9>
DATA<10>
DATA<11>
DATA<12>
DATA<14>
DATA<15>
DATA<16>
DATA<17>
DATA<18>
DATA<19>
DATA<20>
DATA<23>
DATA<21>
DATA<22>
High
Z
Hi-Z
SDO
Don’t care
DATA<13>
A<0>
A<1>
A<2>
A<3>
A<4>
Don’t care
A<5>
SDI
A<6>
SCK
Don’t care
High
Hi-Z Z
READ Communication (SPI mode 0,0)
FIGURE 6-3:
SPI Mode 0,0).
6.4
Read on a Single Register with 24-bit Format (WIDTH_DATA<1:0> = 01,
Two different write mode configurations for the address
increment can be defined through the WRITE bit in the
STATUSCOM register (see Section 6.5 “Continuous
Communications, Looping on Register Sets” and
Table 9-2). The SDO pin stays in a high-impedance
state during a write communication. The data on SDI is
clocked into the MCP3918 on the rising edge of SCK.
The writing format for each register is defined in
Section 5.5 “ADC Output Coding”. A write on an
undefined or non-writable address, such as the ADC
channel register address, will have no effect nor will it
increment the address counter.
Writing to the Device
The first register written from the SDI pin to the device
is the one defined by the address (A<4:0>) given in the
Control byte. After this first register is fully transmitted,
if the CS pin is maintained logic low, the communication
continues without an additional Control byte and the
SDI pin transmits another register with the address
automatically incremented.
CS
Device latches SDI on rising edge
DATA<1>
DATA<2>
DATA<3>
DATA<4>
DATA<5>
DATA<6>
DATA<7>
DATA<8>
DATA<9>
DATA<10>
DATA<11>
DATA<12>
DATA<13>
DATA<14>
DATA<15>
DATA<16>
DATA<17>
DATA<18>
DATA<19>
DATA<20>
DATA<21>
DATA<22>
R/W
DATA<23>
A<0>
A<1>
A<2>
A<3>
A<4>
Don’t care
A<5>
SDI
A<6>
SCK
DATA<0>
Don’t
care
Hi-Z High Z
SDO
WRITE Communication (SPI mode 1,1)
FIGURE 6-4:
Write to a Single Register with 24-bit Format (WIDTH_CRC = 0, SPI Mode 1,1).
2014 Microchip Technology Inc.
DS20005287A-page 45
MCP3918
CS
Device latches SDI on rising edge
SDO
DATA<0>
DATA<1>
DATA<2>
DATA<3>
DATA<4>
DATA<5>
DATA<6>
DATA<7>
DATA<8>
DATA<9>
DATA<10>
DATA<11>
DATA<12>
DATA<13>
DATA<14>
DATA<15>
DATA<16>
DATA<17>
DATA<18>
DATA<19>
DATA<20>
DATA<21>
DATA<23>
DATA<22>
R/W
A<0>
A<1>
A<2>
A<3>
A<4>
Don’t care
A<5>
SDI
A<6>
SCK
Don’t care
High
Hi-Z Z
WRITE Communication (SPI mode 0,0)
FIGURE 6-5:
DS20005287A-page 46
Write to a Single Register with 24-bit Format (WIDTH_CRC = 0, SPI Mode 0,0).
2014 Microchip Technology Inc.
MCP3918
6.5
pin returns logic high. The SPI internal register address
pointer starts by transmitting/receiving the address
defined in the Control byte. After this first
transmission/reception, the SPI internal register
address pointer automatically increments to the next
available address in the register set for each
transmission/reception. When it reaches the last
address in the set, the communication sequence is
finished. The address pointer loops automatically back
to the first address of the defined set and restarts a new
sequence with auto-increment (see Table 6-6). The
undefined or unused addresses are automatically
jumped by the address pointer (they are not considered
to be part of the register map by the address pointer).
This internal address pointer automatic selection
allows the following functionality:
Continuous Communications,
Looping on Register Sets
The MCP3918 digital interface can process
communications in Continuous mode, without having
to enter an SPI command between each read or write
to a register. This feature allows the user to reduce
communication overhead to the strict minimum, which
diminishes EMI emissions and reduces switching noise
in the system.
The registers can be grouped into multiple sets for
continuous communications. The grouping of the
registers in the different sets is defined by the
READ<1:0> and WRITE bits that control the internal
SPI communication address pointer. For a graphical
representation of the register map sets in the function
of the READ<1:0> and WRITE bits, please see
Table 9-2.
•
•
•
•
In the case of a continuous communication, there is
only one Control byte on SDI to start the
communication after a CS pin falling edge. The part
stays within the same communication loop until the CS
Read one ADC channel data continuously
Continuously read the entire register map
Continuously read or write each separate register
Continuously read or write all configuration
registers
CS
ADDRESS SET
SCK
8x
SDI
CONTROL
BYTE
24x
24x
...
24x
24x
24x
...
24x
ADDR
ADDR + 1
Don’t care
Don’t care
...
Starts read sequence
at address ADDR
Complete
READ
sequence
ADDR + n
Roll-over
High Z
Hi-Z
SDO
ADDR
ADDR + 1
...
ADDR + n
ADDR
ADDR + 1
Complete READ sequence
...
ADDR + n
Complete READ sequence
Continuous READ communication (24-bit format)
CS
ADDRESS SET
SCK
8x
SDI
CONTROL
BYTE
24x
24x
...
24x
24x
24x
...
24x
ADDR
ADDR + 1
Don’t care
ADDR
Starts write sequence
at address ADDR
ADDR + 1
...
ADDR + n
ADDR
ADDR + 1
Complete WRITE sequence
...
Complete WRITE sequence
ADDR + n
...
Complete
WRITE
sequence
ADDR + n
Roll-over
High
Hi-Z
SDO
Z
Continuous WRITE communication (24-bit format)
FIGURE 6-6:
Continuous Communication Sequences.
2014 Microchip Technology Inc.
DS20005287A-page 47
MCP3918
6.5.1
CONTINUOUS READ
TABLE 6-1:
READ<1:0>
For continuous reading of ADC data in
SPI Mode 0,0 (see Figure 6-7), once the
data has been completely read after a
data ready pulse, the SDO pin will take the
MSB value of the previous data at the end
of the reading (falling edge of the last SCK
clock). If SCK stays idle at logic low (by
definition of Mode 0,0), the SDO pin will
be updated at the falling edge of the next
Data Ready pulse (synchronously with the
DR pin falling edge with an output timing
of tDODR) with the new MSB of the data
corresponding to the Data Ready pulse.
This mechanism allows the MCP3918 to
continuously read ADC data outputs
seamlessly, even in SPI Mode (0,0).
Note:
The STATUSCOM register contains the loop settings
for the internal register address pointer (READ<1:0>
bits and WRITE bit). For the Continuous Read modes,
the address selection can take the four following
values:
ADDRESS SELECTION IN
CONTINUOUS READ
Register Address Set Grouping
for Continuous Read
Communications
00
Static (No incrementation)
01
Groups
10
Types (Default)
11
Full Register Map
In SPI Mode (1,1), the SDO pin stays in the last state
(LSB of previous data) after a complete reading, which
also allows seamless Continuous Read mode (see
Figure 6-8).
No SDI data coming after the Control byte is
considered during a continuous read communication.
The following figures represent a typical, continuous
read communication with the default settings
(READ<1:0> = 10, WIDTH_DATA<1:0> = 01) for SPI
Mode 0,0 (Figure 6-7) and SPI Mode 1,1 (Figure 6-8).
CS
SCK
SDI
8x
Don’t care
24x
24x
0x01
Don’t care
Starts read sequence at
address 00000
SDO
Hi-Z
DATA_CH0
Stays at
DATA_CH<0>
Complete READ sequence on
the ADC output channel
DATA_CH0
Complete READ sequence on
new ADC output channel
DR
FIGURE 6-7:
Typical Continuous Read Communication (WIDTH_DATA<1:0> = 01, SPI Mode 0,0).
CS
SCK
SDI
8x
Don’t care
24x
0x01
24x
Don’t care
Starts read sequence at
address 00000
SDO
FIGURE 6-8:
DS20005287A-page 48
Hi-Z
DATA_CH0
DATA_CH0 DATA_CH0
<23>
<23>
Old data
New data
DATA_CH0
Typical Continuous Read Communication (WIDTH_DATA<1:0> = 01, SPI Mode 1,1).
2014 Microchip Technology Inc.
MCP3918
6.5.2
CONTINUOUS WRITE
The STATUSCOM register contains the write loop
settings for the internal register address pointer
(WRITE). For the Continuous Write modes, the
address selection can take the two following values:
TABLE 6-2:
WRITE
ADDRESS SELECTION IN
CONTINUOUS WRITE
Register Address Set Grouping for
Continuous Write Communications
0
Static (No incrementation)
1
Types (Default)
SDO is always in a high-impedance state during a
continuous write communication. Writing to a
non-writable address (such as addresses 0x00 to 0x07
or any of the unused register’s addresses) has no
effect and does not increment the address pointer. In
this case, the user needs to stop the communication
and restart a communication with a Control byte
pointing to a writable address (0x08 to 0x1F).
Note:
6.6
When LOCK<7:0> is different from 0xA5,
all the addresses, except for 0x1F,
become non-writable (see Section 6.10
“Locking/Unlocking Register Map
Write Access”)
Situations that Reset and Restart
Active ADC
Immediately after the following actions, the active ADC
(the ones not in Soft Reset or Shutdown modes) is
reset and automatically restarted in order to provide
proper operation:
1.
2.
3.
4.
5.
6.
Change in PHASE register
Overwrite of the same PHASE register value
Change in the OSR<2:0> settings
Change in the PRE<1:0> settings
Change in the CLKEXT setting
Change in the VREFEXT setting
After these temporary resets, the ADC goes back to
normal operation, with no need for an additional
command. Each ADC data output register is cleared
during this process. The PHASE register can be used
to serially soft reset the ADC, without using the RESET
bit in the CONFIG1 register, if the same value is written
in the PHASE register.
2014 Microchip Technology Inc.
6.7
Data Ready Pin (DR)
To communicate when channel data is ready for
transmission, the Data Ready signal is available on the
Data Ready (DR) pin at the end of a conversion. The
DR pin outputs an active-low pulse with a pulse width
equal to half a DMCLK clock period. After a Data Ready
pulse falling edge has occurred, the ADC output data is
updated within the tDODR timing and can then be read
through SPI communication.
The first Data Ready pulse after a Hard or a Soft Reset
is located after the settling time of the sinc filter (see
Table 5-4) plus the phase delay of the corresponding
channel (see Section 5.11 “Crystal Oscillator”).
Each subsequent pulse is then periodic, and the period
is equal to a DRCLK clock period (see Equation 4-3
and Figure 1-3). The Data Ready pulse is always
synchronous with the internal DRCLK clock.
The DR pin can be used as an interrupt pin when
connected to an MCU or DSP, which will synchronize
the readings of the ADC data outputs. When not
active-low, this pin can be either in high-impedance
(when DR_HIZ = 0) or in a defined logic high state
(when DR_HIZ = 1). This is controlled through the
STATUSCOM register. This allows multiple devices to
share the same DR pin (with a pull-up resistor
connected between DR and DVDD). If only the
MCP3918 device is connected on the interrupt bus, the
DR pin does not require a pull-up resistor, and
therefore it is recommended to use the DR_HIZ = 1
configuration for such applications.
The CS pin has no effect over the DR pin, which means
that, even if the CS pin is logic high, the Data Ready
pulses coming from the active ADC channels will still
be provided; the DR pin behavior is independent from
the SPI interface. While the RESET pin is logic low, the
DR pin is not active. The DR pin is latched in the logic
low state when the interrupt flag on the CRCREG is
present to signal that the desired register configuration
has been corrupted (see Section 6.11 “Detecting
Configuration Change through CRC-16 Checksum
on Register Map and its Associated Interrupt
Flag”).
DS20005287A-page 49
MCP3918
6.8
ADC Channel Latching and
Synchronization
The ADC data output register (address 0x00) has a
double buffer output structure. The two sets of latches
in series are triggered by the data ready signal and an
internal signal indicating the beginning of a read
communication sequence (read start).
The first set of latches holds the ADC channel data
output register when the data is ready. This behavior is
synchronous with the MCLK clock.
The second set of latches ensures that, when reading
starts on an ADC output, the corresponding data is
latched, so that no data corruption can occur within a
read. This behavior is synchronous with the SCK clock.
If an ADC read has started, in order to read the
following ADC output, the current reading needs to be
fully completed (all bits must be read on the SDO pin
from the ADC output data registers).
6.9
Securing Read Communications
through CRC-16 Checksum
Since power/energy metering systems can generate or
receive large EMI/EMC interferences and large
transient spikes, it is helpful to secure SPI
communications as much as possible to maintain data
integrity and desired configurations during the lifetime
of the application.
The communication data on the SDO pin can be
secured through the insertion of a Cyclic Redundancy
Check (CRC) checksum at the end of each continuous
reading sequence. The CRC checksum on the
communications can be enabled or disabled through
the EN_CRCCOM bit in the STATUSCOM register. The
CRC message ensures the integrity of the read
sequence bits transmitted on the SDO pin, and the
CRC checksum is inserted in between each read
sequence (see Figure 6-10).
Since the double output buffer structure is triggered
with two events that depend on two asynchronous
clocks (data ready pulse with MCLK and read start with
SCK), it is recommended to implement one of the three
following methods on the MCU or the processor, in
order to synchronize the reading of the channels:
1.
2.
3.
Use the DR pin pulses as an interrupt: once a
falling edge occurs on the DR pin, the data is
available for reading on the ADC output
registers after the tDODR timing. If this timing is
not respected, data corruption can occur.
Use a timer clocked with MCLK as a
synchronization event: since the data ready
pulse is synchronous with MCLK, the user can
calculate the position of the data ready pulse
depending on the PHASE, the OSR<2:0> and
the PRE<1:0> settings. Again, the tDODR timing
needs to be added to this calculation, to avoid
data corruption.
Poll the DRSTATUS bit in the STATUSCOM
register: this method consists of continuously
reading the STATUSCOM register and waiting
for the DRSTATUS bit to be equal to '0'. When
this event happens, the user can start a new
communication to read the desired ADC data. In
this case, no additional timing is required.
The first method is the preferred one, as it can be used
without adding additional MCU code space, but
requires connecting the DR pin to an I/O pin of the
MCU. The two last methods require more MCU code
space and execution time, but they allow synchronizing
the reading of the channels without connecting the DR
pin, which saves one I/O pin on the MCU.
DS20005287A-page 50
2014 Microchip Technology Inc.
MCP3918
CS
ADDRESS SET
SCK
8x
16x/24x/32x
Depending on
data format
16x/24x/32x
Depending on
data format
16x/24x/32x
Depending on
data format
...
16x/24x/32x
Depending on
data format
16x/24x/32x
Depending on
data format
16x/24x/32x
Depending on
data format
...
ADDR
ADDR + 1
SDI
CONTROL
BYTE
Don’t care
Don’t care
...
Starts read sequence
at address ADDR
SDO
High
Hi-ZZ
Complete
READ
sequence
ADDR + n
Roll-over
ADDR
ADDR + 1
...
ADDR + n
ADDR
Complete READ sequence
ADDR + 1
...
ADDR + n
Complete READ sequence
Continuous READ communication without CRC checksum (EN_CRCCOM=0)
CS
ADDRESS SET
SCK
8x
SDI
CONTROL
BYTE
16x/24x/32x
Depending on
data format
16x/24x/32x
Depending on
data format
16x/24x/32x
Depending on
data format
...
16x or 32x
Depending on
CRC format
16x/24x/32x
Depending on
data format
16x/24x/32x
Depending on
data format
...
16x/24x/32x
Depending on
data format
16x or 32x
Depending on
CRC format
ADDR
ADDR + 1
Don’t care
Don’t care
...
Starts read sequence
at address ADDR
SDO
High
Z
Hi-Z
Complete
READ
sequence
ADDR + n
ADDR
ADDR + 1
...
ADDR + n
CRC Checksum
ADDR
ADDR + 1
...
ADDR + n
CRC Checksum
CRC Checksum
(not part of register map)
Roll-over
Complete READ sequence = Message for CRC Calculation
Checksum
New Message
New Checksum
Continuous READ communication with CRC checksum (EN_CRCCOM=1)
FIGURE 6-9:
Continuous Read Sequences With and Without CRC Checksum Enabled.
The CRC checksum in the MCP3918 device uses the
16-bit CRC-16 ANSI polynomial as defined in the IEEE
802.3 standard: x16 + x15 + x2 + 1. This polynomial can
also be noted as 0x8005. CRC-16 detects all single
and double-bit errors, all errors with an odd number of
bits, all burst errors of length 16 or less, and most errors
for longer bursts. This allows an excellent coverage of
the SPI communication errors that can happen in the
system, and heavily reduces the risk of a
miscommunication, even under noisy environments.
The CRC-16 format displayed on the SDO pin depends
on the WIDTH_DATA<1> bit in the STATUSCOM
register (see Figure 6-10). It can be either 16-bit or
32-bit format to be compatible with both 16-bit and
32-bit MCUs. The CRCREG<15:0> bits calculated by
the MCP3918 device are not dependent on the format
(the device always calculates only a 16-bit CRC
checksum).
It
is
recommended
to
keep
WIDTH_DATA<1> = WIDTH_CRC when the CRC
checksum is enabled. If a 32-bit MCU is used in the
application, it is recommended to use 32-bit formats
(WIDTH_DATA<1> = WIDTH_CRC = 1) only.
WIDTH_DATA<1> = 0
16-bit format
WIDTH_DATA<1> = 1
32-bit format
FIGURE 6-10:
15
The CRC computed by the MCP3918 device is fully
compatible with the CRC hardware contained in the
Direct Memory Access (DMA) peripheral of the PIC24
and PIC32 MCU product lines. The CRC message that
should be considered in the PIC® device DMA is the
concatenation of the read sequence and its associated
checksum. When the DMA CRC hardware computes
this extended message, the resulting checksum should
be 0x0000. Any other result indicates that a
miscommunication has happened and that the current
communication sequence should be stopped and
restarted.
Note:
The CRC will be generated only at the end
of the selected address set, before the
rollover of the address pointer occurs (see
Figure 6-10).
0
CRCCOM CRCCOM
<15:8>
<7:0>
31
CRCCOM CRCCOM
<15:8>
<7:0>
0
0x00
0x00
CRC Checksum Format.
2014 Microchip Technology Inc.
DS20005287A-page 51
MCP3918
6.10
Locking/Unlocking Register Map
Write Access
The MCP3918 digital interface includes an advanced
security feature that allows locking or unlocking the
register map write access. This feature prevents the
miscommunications that can corrupt the desired
configuration of the device, especially an SPI read
becoming an SPI write because of the noisy
environment.
The last register address of the register map
(0x1F: LOCK/CRC) contains the LOCK<7:0> bits. If
these bits are equal to the password value (which is
equal to the default value of 0xA5), the register map
write access is not locked. Any write can take place and
communications are not protected.
When the LOCK<7:0> bits are different from 0xA5, the
register map write access is locked. The register map
and therefore the full device configuration are
write-protected. Any write to an address other than
0x1F will yield no result. All the register addresses,
except for 0x1F, become read-only. In this case, if the
user wants to change the configuration, the
LOCK<7:0> bits have to be reprogrammed back to
0xA5 before sending the desired write command.
The LOCK<7:0> bits are located in the last register, so
that the user can program the whole register map,
starting from 0x09 to 0x1E within one continuous write
sequence, and then lock the configuration at the end of
the sequence with writing all zeros, for example in the
0x1F address.
6.11
Detecting Configuration Change
through CRC-16 Checksum on
Register Map and its Associated
Interrupt Flag
In order to prevent internal corruption of the register
and to provide additional security on the register map
configuration, the MCP3918 device includes an
automatic and continuous CRC checksum calculation
on the full register map configuration bits. This
calculation is not the same as the communication CRC
checksum described in Section 6.9 “Securing Read
Communications through CRC-16 Checksum”.
This calculation takes the full register map as the CRC
message and outputs a checksum on the
CRCREG<15:0> bits located in the LOCK/CRC
register (address 0x1F).
Since this feature is intended to protect the
configuration of the device, this calculation is run
continuously only when the register map is locked
(LOCK<7:0> different from 0xA5, see Section 6.10
“Locking/Unlocking Register Map Write Access”).
If the register map is unlocked, the CRCREG<15:0>
bits are cleared and no CRC is calculated.
The calculation is fully completed in ten DMCLK
periods and refreshed every ten DMCLK periods
continuously. The CRCREG<15:0> bits are reset when
a POR or a hard reset occurs. All the bits contained in
the defined registers from addresses 0x09 to 0x1F are
processed by the CRC engine to give the
CRCREG<15:0>. The DRSTATUS bit is set to '1'
(default) and the CRCREG<15:0> bits are set to '0'
(default) for this calculation engine, as they could vary
during the calculation.
An interrupt flag can be enabled through the EN_INT
bit in the STATUSCOM register and provided on the DR
pin when the configuration has changed without a write
command being processed. This interrupt is a logic low
state. This interrupt is cleared when the register map is
unlocked (since CRC calculation is not processed
anymore).
At power-up, the interrupt is not present and the
register map is unlocked. As soon as the user finishes
writing its configuration, the user needs to lock the
register map (writing 0x00 for example in the LOCK
bits) to be able to use the interrupt flag. The
CRCREG<15:0> bits will be calculated for the first time
in 10 DMCLK periods. This first value will then be the
reference checksum value and will be latched
internally, until a hard reset, a POR or an unlocking of
the register map happens. The CRCREG<15:0> will
then be calculated continuously and checked against
the reference checksum. If the CRCREG<15:0> is
different from the reference, the interrupt sends a flag
by setting the DR pin to a logic low state until it is
cleared.
DS20005287A-page 52
2014 Microchip Technology Inc.
MCP3918
6.12
Interface Mode Selection
(SPI or 2-Wire)
The MCP3918 includes two different digital interfaces:
a standard 4-wire half duplex SPI interface (see
Section 6.0 “SPI Serial Interface Description”) and
a 2-wire interface dedicated for digitally isolated
applications (see Section 7.0 “2-Wire Serial Interface
Description”).
The selection between these two interfaces is possible
only when the CLKEXT bit is high (CLKEXT = 1). This
is the case by default at POR. When the CLKEXT = 1
condition is true, the OSC2/MODE pin becomes the
selection input pin for the Interface mode.
When OSC2/MODE is logic low during the
CLKEXT = 1 condition, the SPI interface is selected.
When OSC2/MODE pin is logic high, the 2-Wire
Interface is selected (see Figure 1-5 for the 2-Wire
mode selection timing diagram).
If OSC2/MODE pin is left floating while CLKEXT = 1,
an internal pull-down (35 µA typical current)
automatically selects the SPI mode as the default
interface.
The MODE selection is not combinatorial, it is latched
at each POR, Hard Reset and Watchdog Time Reset.
In other words, to change from one interface mode to
another, the user needs to create one of these three
resets and change the OSC2/MODE logic input state
before exiting the applied reset.
2014 Microchip Technology Inc.
DS20005287A-page 53
MCP3918
NOTES:
DS20005287A-page 54
2014 Microchip Technology Inc.
MCP3918
7.0
2-WIRE SERIAL INTERFACE
DESCRIPTION
7.1
Overview
The 2-Wire Interface mode is designed for applications
that require galvanic isolation. It allows a minimum
number of digital isolator channels, specifically one
bi-directional or two unidirectional channels, to be
connected to the MCP3918 when interfacing through
an isolation barrier. This functionality reduces the total
system cost in an isolated application system, like a
polyphase shunt-based energy meter. It is
recommended to use the MCP3918 with the 2-Wire
mode for digitally isolated applications and with the SPI
mode for other applications where galvanic isolation is
not required.
The principle of this 2-Wire interface is simple: it has a
serial clock input pin (SCK/MCLK) and a serial data
output pin (SDO), and it automatically sends output
data in packets (frames) at a DRCLK data rate (every
time new data is available on the ADC output). It has no
serial input pin to diminish the number of isolated
channels. At the same time, the serial clock pin SCK
also becomes the master clock (MCLK) input pin of the
device, and the part becomes fully synchronous with
SCK = MCLK. The system then becomes fully
synchronous and can be driven by only one master
clock for multiple phases, which ensures proper
synchronization and constant phase angle between
phases, which is important for an energy metering
application.
ANALOG
The SDO pin becomes the only output of the device
and is fully synchronous with the serial/master clock.
The SDO pin is never in high-impedance in this mode,
and is by default at logic low when not transmitting
data. The SDO pin idles logic low in this mode because
most of the digital isolator devices consume less
current in a logic low state than in a logic high state.
This effectively reduces the total power consumption of
a system with digital isolation devices.
When the part has entered 2-Wire mode, the logic pins
RESET, SDI, CS, OSC1 and DR become logic input
pins for the configuration of the device (respectively
OSR0/OSR1/BOOST/GAIN0/GAIN1). These pins
need to have well-defined logic states for low-power
applications. These pins define the only settings that
can be modified in 2-Wire mode.
The MDAT0 pin is always disabled and kept in a
high-impedance state during the 2-Wire Interface
mode. This pin can be grounded for applications using
exclusively the 2-Wire Interface mode so that the
EMI/EMC susceptibility of the part is improved.
DIGITAL
SDO
SINC3
CH0+
CH0-
+
PGA
MCP3918
Isolator
MOD<3:0>
'6
Modulator
To SPI Ports
Of an MCU
SCK/MCLK
Isolator
2-wire
Interface
GAIN0
GAIN1
BOOST
OSR0
OSR1
Logic inputs
connected
to DVDD or
DGND
Main MCU/
CPU Board
Isolation
Barrier
FIGURE 7-1:
MCP3918 2-Wire Interface Typical Application Schematic.
2014 Microchip Technology Inc.
DS20005287A-page 55
MCP3918
7.2
7.2.3
2-Wire Mode Configuration
Settings
When the user wants to exclusively use the 2-Wire
Interface mode in digitally isolated applications, the
OSC2 pin should always be in a logic high state,
starting from the power-up of the part. Otherwise, the
user can change the interface mode by toggling the
OSC2/MODE pin within a POR, a Hard Reset or a
Watchdog Timer Reset; the MODE is latched when
exiting one of these three types of reset. When the part
has entered 2-Wire mode, the entire part configuration
keeps its default settings (see Section 9.0 “MCP3918
Internal Registers” for the default settings of all
internal registers), except for the configuration of the
Gain in Channel 0, the OSR and the BOOST settings.
In
2-Wire
mode,
the
input
pins
OSR0/OSR1/BOOST/GAIN0/GAIN1 are latched on
the OSC2/MODE rising edge and should typically be
directly connected to DVDD or DGND, depending on the
desired configuration. These pins define the only
configurable settings in 2-Wire mode. If more settings
are required by the application, it is recommended to
use the SPI mode. The following tables describe the
configuration options for these five pins.
7.2.1
OSR1/OSR0
OSR Setting Logic
Schmitt-triggered.
TABLE 7-1:
Pins.
These
inputs
OSR SETTINGS
OSR1
OSR0
OSR
0
0
64
0
1
128
1
0
256
1
1
512
7.2.2
are
BOOST
Current Boost Setting Logic Pin. This input is
Schmitt-triggered.
TABLE 7-2:
CURRENT BOOST SETTINGS
BOOST PIN
BOOST
0
0.5x
1
1x
DS20005287A-page 56
GAIN1/GAIN0
PGA Gain Setting Logic Pins. These inputs are
Schmitt-triggered.
TABLE 7-3:
7.3
CHANNEL 0 GAIN SETTINGS
GAIN1
GAIN0
CH0 PGA GAIN
0
0
1
0
1
8
1
0
16
1
1
32
2-Wire Communication Protocol
In 2-Wire mode, the SCK/MCLK pin needs to be
clocked continuously at all times for proper operation.
Any change in the clock frequency will lead to
degraded THD/SFDR specifications. The part obeys
the same timing specifications in both SPI and 2-Wire
Interface mode for SCK/SDO pins. The MCLK
maximum input frequency is 10 MHz in 2-Wire mode,
since the converter still respects Table 5-2 for
maximum AMCLK frequency (provided the part has
entered 2-Wire mode at power-up). Since the MCLK is
divided internally, the part accepts a wide range of duty
cycles for the SCK input, provided the serial interface
timings are respected.
In 2-Wire Interface mode, communication uses framed
data sets on the SDO to output data at a fixed data rate,
synchronously with SCK, and using only one output
pin. The frame is different depending on the device and
the oversampling ratio (OSR) selected. When in
OSR = 64 mode, the MCP3918 frame contains the
sync bytes (16-bit), one channel of 16-bit ADC data and
a 16-bit CRC. For OSR = 128 and higher, each frame
is a group of 7 bytes (56 bits), clocked by the serial
clock SCK. Each frame is composed of a sync word (2
bytes), 24-bit data output word (3 bytes) and CRC. The
sync word comes first, followed by Channel 0 ADC
output (DATA_CH0<23:0>) and 16-bit CRC. See
Figures 7-1 and 7-2.
As a verification feature, the sync word contains all
settings coming from the five logic input pins available
(OSR0/1, GAIN0/1, BOOST), in order to provide the
user with the information about this configuration. It
also provides information about the count of the frame
through bits CNT0/1, which is useful when the SDO is
multiplexed at the output of the digital isolators (see
next paragraph). The sync word also contains an
additional sync byte (fixed at 0xA5 value) for additional
security in synchronization and communication.
2014 Microchip Technology Inc.
MCP3918
DATA_CH0<23:0>
1
0
1
1
0
0
CNT1
CNT0
1
0
G0
BOOST
0
SDO
OSR1
OSR0
G1
SCK/
MCLK
SYNC WORD (2 Bytes)
CRCCOM<15:0>
CHANNEL 0 ADC DATA (3 Bytes)
CRCCOM on Entire Frame (2 Bytes)
SDO OUTPUT FRAME (7 Bytes, 56x clocks per Frame)
FRAME CLOCKING FOR OSR>64
DATA_CH0<15:0>
1
0
1
0
0
1
0
CNT1
CNT0
1
G1
G0
SDO
BOOST
0
OSR1
OSR0
SCK/
MCLK
SYNC WORD (2 Bytes)
CRCCOM<15:0>
CHANNEL 0 ADC DATA (2 Bytes)
CRCCOM on Entire Frame (2 Bytes)
SDO OUTPUT FRAME (6 Bytes, 48x clocks per Frame)
FRAME CLOCKING FOR OSR=64
FIGURE 7-2:
Frame Word.
TABLE 7-4:
3), and retrieved on a single SDO line after the digital
isolators, provided that the isolators have a chip enable
or a multiplexing feature. The frame counter can then
be used to retrieve the information about which
MCP3918 part is actually being read. After the four
frames have been transmitted, the SDO pin idles logic
low to reduce digital isolator power consumption until
the next data is available. Figure 7-3 displays the
timing diagram for the 2-Wire Interface mode, showing
all OSR possibilities. Note that the first set of frames is
sent only when the first data is ready, which means that
the settling time of the sinc filter will be elapsed before
sending the first set of frames, as represented in
Figure 7-3.
FRAME COUNTER SETTINGS
CNT1
CNT0
FRAME NUMBER
0
0
FRAME0
0
1
FRAME1
1
0
FRAME2
1
1
FRAME3
These four frames can be used to multiplex SDO at the
output of the digital isolators. In this case, up to
four channels (typically three phases and one neutral
for energy metering applications) can be multiplexed.
The output data of each individual MCP3918 device
can be attributed to a different frame (FRAME0, 1, 2 or
OSC2/
MODE
2-Wire Mode
0
DATA=D1
DATA=D6
0
DATA=D2
DATA=D3
Hi-Z
(OSR=512)
0
0
0
DATA=D9
0
256x
clocks
0
FRAME0
FRAME1
FRAME2
FRAME3
FRAME0
FRAME1
FRAME2
FRAME3
256x
clocks
FRAME0
FRAME1
FRAME2
FRAME3
0
FRAME0
FRAME1
FRAME2
FRAME3
FRAME0
FRAME1
FRAME2
FRAME3
FRAME0
FRAME1
FRAME2
FRAME3
DATA=D8
FRAME0
FRAME1
FRAME2
FRAME3
0
DATA=D7
FRAME0
FRAME1
FRAME2
FRAME3
FRAME0
FRAME1
FRAME2
FRAME3
FRAME0
FRAME1
FRAME2
FRAME3
FRAME0
FRAME1
FRAME2
FRAME3
0
FRAME0
FRAME1
FRAME2
FRAME3
0
FRAME0
FRAME1
FRAME2
FRAME3
256x
clocks
DATA=D10
FRAME0
FRAME1
FRAME2
FRAME3
0
DATA=D5
FRAME0
FRAME1
FRAME2
FRAME3
256x
clocks
DATA=D4
FRAME0
FRAME1
FRAME2
FRAME3
0
0
FRAME0
FRAME1
FRAME2
FRAME3
DATA=D4
FRAME0
FRAME1
FRAME2
FRAME3
0
DATA=D3
FRAME0
FRAME1
FRAME2
FRAME3
0
FRAME0
FRAME1
FRAME2
FRAME3
DATA=D2
FRAME0
FRAME1
FRAME2
FRAME3
0
FRAME0
FRAME1
FRAME2
FRAME3
0
0
256x
clocks
DATA=D10 DATA=D11 DATA=D12 DATA=D13 DATA=D14 DATA=D15 DATA=D16 DATA=D17 DATA=D18 DATA=D19 DATA=D20 DATA=D21 DATA=D22
0
FRAME0
FRAME1
FRAME2
FRAME3
256x
clocks
DATA=D9
0
FRAME0
FRAME1
FRAME2
FRAME3
256x
clocks
FRAME0
FRAME1
FRAME2
FRAME3
256x
clocks
FRAME0
FRAME1
FRAME2
FRAME3
256x
clocks
DATA=D8
(OSR=256)
SDO
256x
clocks
FRAME0
FRAME1
FRAME2
FRAME3
256x
clocks
DATA=D7
Hi-Z
0
256x
clocks
FRAME0
FRAME1
FRAME2
FRAME3
256x
clocks
DATA=D5 DATA=D6
DATA=D1
SDO
256x
clocks
DATA=D4
(OSR=128)
0
256x
clocks
DATA=D2 DATA=D3
Hi-Z
0
256x
clocks
FRAME0
FRAME1
FRAME2
FRAME3
DATA=D1
256x
clocks
FRAME0
FRAME1
FRAME2
FRAME3
SDO
256x
clocks
FRAME0
FRAME1
FRAME2
FRAME3
0
256x
clocks
FRAME0
FRAME1
FRAME2
FRAME3
0
DATA=0
256x
clocks
FRAME0
FRAME1
FRAME2
FRAME3
0
256x
clocks
FRAME0
FRAME1
FRAME2
FRAME3
Hi-Z
(OSR=64)
256x
clocks
FRAME0
FRAME1
FRAME2
FRAME3
256x
clocks
FRAME0
FRAME1
FRAME2
FRAME3
SDO
256x
clocks
FRAME0
FRAME1
FRAME2
FRAME3
256x
clocks
SCK/MCLK
DATA=D1
Internal data ready (Data is
unsettled). No frame is transmitted
FIGURE 7-3:
Data Ready.
New data is available
MCP3918 2-Wire Communication Protocol.
2014 Microchip Technology Inc.
DS20005287A-page 57
MCP3918
7.4
Watchdog Timer Reset, Resetting
the Part when in 2-Wire Mode
When the part has entered 2-Wire mode, the Hard
Reset mode functionality is not available because the
RESET pin becomes the logic input for OSR0. If the
user wants to execute a full reset of the part without
doing a POR, the 2-Wire mode incorporates an internal
watchdog timer that automatically performs a full reset
of the part, provided that the timer has elapsed.
The watchdog timer starts synchronously with each
rising edge of SCK/MCLK. If the SCK logic high state is
maintained for a time that is larger than tWATCH, the
watchdog timer circuit forces the full reset of the chip,
which then returns to its default configuration with the
ADC being reset. If the SCK logic high state is
maintained for a time shorter than tWATCH and then
SCK/MCLK toggles to logic low, the internal timer is
cleared, waiting for another rising edge to restart.
The watchdog timer functionality induces a restriction
in the usable range of frequencies on SCK/MCLK. In
order to avoid intermittent resets in all cases, the
minimum SCK/MCLK frequency in 2-Wire Interface
mode is equal to the inverse of the minimum tWATCH
time (1/(2 x 3.6 µs) = 138.9 kHz, if the duty cycle of the
SCK/MCLK is 50%).
The watchdog timer starts only on the rising edge of
SCK/MCLK, not on the falling edge. Maintaining
SCK/MCLK at a logic low state for large periods of time
does not create any watchdog timer resets. A
Watchdog Timer Reset is created only when the
SCK/MCLK state is maintained logic high during a long
enough period of time.
This watchdog timer period permits exiting the 2-Wire
interface, if desired, by toggling the OSC2/MODE pin to
logic low before creating the Watchdog Timer Reset
and maintaining it logic low until the reset occurs.
DS20005287A-page 58
2014 Microchip Technology Inc.
MCP3918
8.0
The isolator used between MCU and ADC needs to be
fast enough to support the high-speed clock between
MCU and ADC and the data coming from ADC to MCU.
BASIC APPLICATION
CONFIGURATION
One of the main applications for the MCP3918 is
energy/power measurement in systems where the
ADC sampling the current needs to be isolated from the
rest of the design. Figure 8-1 can be used as a starting
point for MCP3918 applications.
This is typically the case in a polyphase shunt-based
power/energy metering or monitoring application. In
this case, each phase needs to be isolated from the
rest of the design and, since the sensor is not providing
this isolation, the isolation needs to be provided at the
output of the analog front-end.
For power measurements, since MCP3918 is a
1-channel ADC, it is recommended to use it for current
samples acquisition and to use the MCU ADC for
voltage samples acquisition.
A_3.3D
U18
L2
2
MCP1754-3.3V
GND
ND
A_3.3A
VOUT VIN
0.1uF
5
U7
VBT1-S5-S5
C63
4.7uF
4
1
C57
3
A_GNDD
5V
+Vout +Vin
DC
The MCP3918 device is built to work seamlessly with a
large variety of two-channel unidirectional digital
isolators (opto-couplers, capacitive or inductive
integrated digital isolators with or without embedded
power supplies).
DC
-Vout -Vin
2
1
C60
4.7uF
0.1uF
0603
8
7
6
5
3910A_SDO
3910A_CLKIN
A_GNDD
GND
NT3
A_3.3D
A_3.3D
C22
A_GNDD
3.3D
U21
VDD2V
VDD1
VIA VOA
VOB VIB
GND2G
GND1
FOD8012
1
2
3
4
3.3D
3910A_SDO_MCU/RC3
3910_CLKIN_MCU_A
C68
0.1uF
0603
GND
GND
A_3.3D A_GNDD
1k
A_GNDA
R80
HIGH
J24
A_GNDA
A_GNDA
R3
CP1
Via_1.6x1
LINE_SHUNT1
LINE_SHUNT2
CP2
Via_1.6x1
A_GNDA
A_3.3D
A_3.3A
C1
C43
0.1uF
DNP
R4
FB2
R100
1k
0.1uF
C52
0.1uF
R76
10
1k
10
4
5
C5
0.1uF
DNP
A_GNDA
2
3
R5
FB3
R6
1
A_GNDA
6
A_GNDA
7
A_GNDA
8
A_GNDA
9
C46
10
0.1uF
U3
RESET / OSR0
SDI / OSR1
DVDD
SDO
AVDD
SCK / MCLK
CH0+
CS / BOOST
CH0-
OSC2 / MODE
NC
OSC1/CLKI
NC
DR / GAIN1
AGND
MDAT0
RFIN/OUT+
MDAT1
RFIN-
DGND
LOW
OSR1
3 2 1
LOW
HIGH
BOOST
3 2 1
LOW
HIGH
GAIN0
3 2 1
LOW
HIGH
GAIN1
3 2 1
LOW
HIGH
A_GNDD
OSR0
3 2 1
J25
20
19 R86
10
18 R87
10
17
16 R79
1k
15
14
3910A_SDO
J26
3910A_CLKIN
J27
A_3.3D
J28
13
12
11
MCP3918A1T/ISS
A_GNDA A_GNDA
A_GNDD
PHASE A
FIGURE 8-1:
Phase.
8.1
MCP3918 Three-Phase Shunt Energy Meter – Typical Application Schematic for Each
Power Supply Design and
Bypassing
To power the isolated ADC, an isolated DC/DC
converter that can be embedded with the isolated data
communication channels (as in Figure 8-1) or other
structures that provide isolated power supplies (e.g.,
fly-back converter) can be used.
For single-phase designs where isolation between
ADC and MCU is not required, the SPI connection is
also available. This SPI interface could also be used
with isolators but this would require four isolators
instead of two (for the 2-wire mode) and, therefore, this
configuration is not preferred.
2014 Microchip Technology Inc.
8.2
Power Supply Design and
Bypassing
The MCP3918 device was designed to measure
positive and negative voltages that might be generated
by a current-sensing device. This current-sensing
device, with a common-mode voltage close to 0V, is
referred to as AGND, which is a shunt or current
transformer (CT) with burden resistors attached to
ground.
The high performance and good flexibility that
characterize this ADC enable it to be used in other
applications, as long as the absolute voltage on each
pin, referred to AGND, stays in the -1V to +1V range.
DS20005287A-page 59
MCP3918
In any system, the analog ICs (such as references or
operational amplifiers) are always connected to the
analog ground plane. The MCP3918 should also be
considered as a sensitive analog component, and
should be connected to the analog ground plane. The
ADC features two pairs of pins: AGND, AVDD, DGND and
DVDD. For best performance, it is recommended to
keep the two pairs connected to two different networks
(Figure 8-2). This way, the design will feature two
ground traces and two power supplies (Figure 8-3).
This means the analog circuitry (including MCP3918)
and the digital circuitry (MCU) should have separate
power supplies and return paths to the external ground
reference, as described in Figure 8-2.
An example of a typical power supply circuit, with
different lines for analog and digital power, is shown in
Figure 8-3. A possible split example is shown in
Figure 8-4, where the ground star connection can be
done at the bottom of the device with the exposed pad.
The split between analog and digital can be done under
the device, and AVDD and DVDD can be connected
together with lines coming under the ground plane.
Another possibility, sometimes easier to implement in
terms of PCB layout, is to consider the MCP3918 as an
analog component and, therefore, to connect both
AVDD and DVDD together, and AGND and DGND
together, with a star connection. In this scheme, the
decoupling capacitors may be larger, due to the ripple
on the digital power supply (caused by the digital filters
and the SPI interface of the MCP3918) now causing
glitches on the analog power supply.
Note:
FIGURE 8-3:
DS20005287A-page 60
ID
IA
0.1 μF
0.1 μF
C
VA
AVDD DVDD
VD
MCP39XX
MCU
AGND
DGND
IA
ID
“Star” Point
D-=
A-=
FIGURE 8-2:
All Analog and Digital
Return Paths Need to Stay Separate with Proper
Bypass Capacitors.
The “Net Tie” Object NT2 represents the start ground connection.
Power Supply with Separate Lines for Analog and Digital Sections.
2014 Microchip Technology Inc.
MCP3918
The ferrite bead between the digital and analog ground
planes helps keep high-frequency noise from entering
the device. This ferrite bead is recommended to be low
resistance; most often it is a THT component. Ferrite
beads are typically placed on the shunt inputs and into
the power supply circuit for additional protection.
8.3
SPI Interface Digital Crosstalk
The MCP3918 incorporates a high-speed 20-MHz SPI
digital interface. This interface can induce a crosstalk,
if it is running at its full speed without any precautions.
The crosstalk is caused by the switching noise created
by the digital SPI signals (also called ground bouncing).
FIGURE 8-4:
Separation of Analog and
Digital Circuits on Layout.
Figure 7-5 shows a more detailed example with a direct
connection to a high-voltage line (e.g., a two-wire 120V
or 220V system). A current-sensing shunt is used for
current measurement on the high/line side that also
supplies the ground for the system. This is necessary
as the shunt is directly connected to the channel input
pins of the MCP3918. To reduce sensitivity to external
influences, such as EMI, these two wires should form a
twisted pair, as noted in Figure 8-5. The power supply
and MCU are separated on the right side of the PCB,
surrounded by the digital ground plane. The MCP3918
is kept on the left side, surrounded by the analog
ground plane. There are two separate power supplies
going to the digital section of the system and the analog
section, including the MCP3918. With this placement,
there are two separate current supply paths and
current return paths, IA and ID.
Analog Ground Plane
IA
This crosstalk would negatively impact the SNR in this
case. The noise is attenuated if a proper separation
between the analog and digital power supplies is put in
place (see Section 8.2 “Power Supply Design and
Bypassing”). In order to further remove the influence
of the SPI communication on measurement accuracy,
it is recommended to add series resistors on the SPI
lines to reduce the current spikes caused by the digital
switching noise (see Figure 8-1 where these resistors
have been implemented). The resistors also help to
keep the level of electromagnetic emissions low. The
measurement graphs provided in this data sheet have
been performed with 100series resistors connected
on each SPI I/O pin. Measurement accuracy disturbances have not been observed even at the full speed
of 20 MHz interfacing. The crosstalk performance is
dependent on the package choice due to the difference
in the pin arrangement (dual in-line or quad), and is
improved in the QFN-20 package.
Digital Ground Plane
ID
MCU
MCP3918
ID
IA
VD VA
Power Supply
Circuitry
Twisted
Pair
LINE
“Star” Point
SHUNT
NEUTRAL
FIGURE 8-5:
Connection Diagram.
2014 Microchip Technology Inc.
DS20005287A-page 61
MCP3918
8.4
Sampling Speed and Bandwidth
If ADC power consumption is not a concern in the
design, the boost settings can be increased for best
performance so that the OSR is always kept at the
maximum settings to improve the SINAD performance
(see Table 7-1). If the MCU cannot generate a clock
fast enough, it is possible to tap the OSC1/OSC2 pins
of the MCP3918 crystal oscillator directly to the crystal
of the microcontroller. When the sampling frequency is
enlarged, the phase resolution is improved, and with
the OSR increased, the phase compensation range
can be kept in the same range as the default settings.
TABLE 8-1:
SAMPLING SPEED VS. MCLK
AND OSR, ADC PRESCALE
1:1
MCLK
(MHz)
Boost
OSR
Sampling
Speed
(ksps)
16
0b11
1024
3.91
14
0b11
1024
3.42
12
0b11
1024
2.93
10
0b10
1024
2.44
8
0b10
512
3.91
6
0b01
512
2.93
4
0b01
256
3.91
8.5
Differential Inputs Anti-Aliasing
Filter
Due to the nature of the ADC used in the MCP3918
(oversampling converter), each differential input of the
ADC channels requires an anti-aliasing filter so that the
oversampling frequency (DMCLK) is largely attenuated
and does not generate any disturbances on the ADC
accuracy. This anti-aliasing filter also needs to have a
gain close to the one in the signal bandwidth of interest.
Typically, for 50/60 Hz measurement and default
settings (DMCLK = 1 MHz), a simple RC filter with
1 k and 100 nF can be used. The anti-aliasing filter
used for the measurement graphs is a first-order RC
filter with 1 k and 15 nF. The typical schematic for
connecting a current transformer to the ADC is shown
in Figure 8-6. If wires are involved, twisting them is also
recommended.
DS20005287A-page 62
FIGURE 8-6:
First-Order Anti-Aliasing
Filter for CT-Based Designs.
The di/dt current sensors, such as Rogowski coils, can
be an alternative to current transformers. Since these
sensing
elements
are
highly
sensitive
to
high-frequency electromagnetic fields, using a
second-order anti-aliasing filter is recommended to
increase the attenuation of potential perturbing RF
signals.
FIGURE 8-7:
Second-Order Anti-Aliasing
Filter for Rogowski Coil-Based Designs.
The filter presented in Figure 8-7 is an anti-aliasing
filter. The di/dt integrator can be created in firmware as
a first-order low-pass filter with corner frequency much
lower than the input signal.
The MCP3918 is highly recommended in applications
using di/dt as current sensors because of the extremely
low noise floor at low frequencies. In such applications,
a low-pass filter (LPF) with a cut-off frequency much
lower than the signal frequency (50/60 Hz for metering)
is used to compensate for the 90 degree shift and for
the 20 db/decade attenuation induced by the di/dt
sensor. Because of this filter, the SNR will be
decreased, since the signal will be attenuated by a few
orders of magnitude, while the low-frequency noise will
not be attenuated. Usually, a high-order high-pass filter
(HPF) is used to attenuate the low-frequency noise in
order to prevent a dramatic degradation of the SNR,
which can be very important in other parts. A high-order
filter will also consume a significant portion of the
computation power of the MCU. When using the
MCP3918, such a high-order HPF is not required, since
this part has a low noise floor at low frequencies. A
first-order HPF is enough to achieve very good
accuracy.
2014 Microchip Technology Inc.
MCP3918
8.6
Energy Measurement Error
Considerations
The measurement error is a typical representation of
the non-linearity of the ADC (see Section 4.0
“Terminology and Formulas” for the definition of
measurement error). The measurement error is
dependent on the THD and on the noise floor of the
ADC. The measurement error specification on the
MCP3918 can be improved by increasing the OSR (to
get a better SINAD and THD performance) and, to
some extent, the BOOST settings (if the bandwidth of
the measurements is too limited by the bandwidth of
the amplifiers in the sigma-delta ADC). In most of the
energy metering AC applications, high-pass filters are
used to cancel the offset on each ADC channel (current
and voltage channels), and therefore a single-point
calibration is necessary to calibrate the system for
active energy measurement. This calibration is a
system gain calibration, and the user can utilize the
EN_GAINCAL bit and the GAINCAL_CH0 register to
perform this digital calibration. After such calibration,
typical measurement error curves like the ones in
Figure 2-7 can be generated by sweeping the current
channel amplitude and measuring the energy at the
outputs (the energy calculations here are being
realized off-chip). The error is measured using a gain of
1x, as it is commonly used in most CT-based
applications.
At low signal amplitude values (typically 1000:1
dynamic range and higher), the crosstalk between
channels, mainly caused by the PCB, becomes a
significant part of the perturbation as the measurement
error increases. The 1-point measurement error curves
in Figure 2-5 have been performed with a full-scale
sine wave on all the inputs that are not measured,
which means that these channels induce a maximum
amount of crosstalk on the measurement error curve.
In order to avoid such behavior, a 2-point calibration
can be put in place in the calculation section.
This 2-point calibration can be a simple linear
interpolation between two calibration points (one at
high amplitudes, one at low amplitudes at each end of
the dynamic range) and helps to significantly lower the
effect of crosstalk between channels. A 2-point
calibration is very effective in maintaining the
measurement error close to zero on the whole dynamic
range, since the non-linearity and distortion of the
MCP3918 is very low. Figure 2-6 shows the
measurement error curves obtained with the same
ADC data taken for Figure 2-5, but where a 2-point
calibration has been applied. The difference is
significant only at the low end of the dynamic range,
where all the perturbing factors are a bigger part of the
ADC output signals. These curves show extremely tight
measurement error across the full dynamic range
(here, typically 10,000:1), which is required in
high-accuracy class meters.
2014 Microchip Technology Inc.
DS20005287A-page 63
MCP3918
NOTES:
DS20005287A-page 64
2014 Microchip Technology Inc.
MCP3918
9.0
MCP3918 INTERNAL
REGISTERS
The addresses associated with the internal registers
are listed in Table 9-1. This section also describes the
registers in detail. All registers are 24-bit long registers,
which can be addressed and read separately.
TABLE 9-1:
The format of the data register (0x00) can be changed
through the WIDTH_CRC and WIDTH_DATA<1:0> bits
in the STATUSCOM register. The READ<1:0> and
WRITE bits define the groups and types of registers for
continuous read/write communication or looping on
address sets, as shown in Table 9-2.
MCP3918 REGISTER MAP
Address
Name
Bits
R/W
0x00
CHANNEL0
24
R
Channel 0 ADC Data <23:0>, MSB first
0x01
Unused
24
U
Unused
0x02
Unused
24
U
Unused
0x03
Unused
24
U
Unused
0x04
Unused
24
U
Unused
0x05
Unused
24
U
Unused
0x06
Unused
24
U
Unused
0x07
Unused
24
U
Unused
0x08
MOD
24
R/W
0x09
PHASE
24
U
0x0A
Unused
24
U
0x0B
GAIN
24
R/W
0x0C
STATUSCOM
24
R/W
Status and Communication Register
0x0D
CONFIG0
24
R/W
Configuration Register
0x0E
CONFIG1
24
R/W
Configuration Register
0x0F
OFFCAL_CH0
24
R/W
Offset Correction Register - Channel 0
0x10
GAINCAL_CH0
24
R/W
Gain Correction Register - Channel 0
0x11
Unused
24
U
Unused
0x12
Unused
24
U
Unused
0x13
Unused
24
U
Unused
0x14
Unused
24
U
Unused
0x15
Unused
24
U
Unused
0x16
Unused
24
U
Unused
0x17
Unused
24
U
Unused
0x18
Unused
24
U
Unused
0x19
Unused
24
U
Unused
0x1A
Unused
24
U
Unused
0x1B
Unused
24
U
Unused
0x1C
Unused
24
U
Unused
0x1D
Unused
24
U
Unused
0x1E
Unused
24
U
Unused
0x1F
LOCK/CRC
24
R/W
2014 Microchip Technology Inc.
Description
Delta-sigma Modulators Output Value
Phase Delay Configuration Register
Unused
Gain Configuration Register
Security Register (password and CRC-16 on Register Map)
DS20005287A-page 65
MCP3918
TABLE 9-2:
REGISTER MAP GROUPING FOR ALL CONTINUOUS READ/WRITE MODES
Address
CHANNEL 0
0x00
MOD
0x08
GAIN
0x0B
STATUSCOM
0x0C
CONFIG0
0x0D
CONFIG1
0x0E
OFFCAL_CH0
0x0F
GAINCAL_CH0
0x10
LOCKCRC
0x1F
DS20005287A-page 66
WRITE
= ‘11‘
= ‘10‘
= ‘01‘
= ‘00‘
LOOP ENTIRE REGISTER MAP
READ<1:0>
Function
TYPE
GROUP
Static
GROUP
GROUP
TYPE
GROUP
= ‘0‘
Not Writable
Static
Static
Static
Static
Static
Static
Static
Static
GROUP
= ‘1‘
Static
TYPE
Static
Static
Static
Static
Static
Static
Static
2014 Microchip Technology Inc.
MCP3918
9.1
CHANNEL Register –
ADC Channel Data
Output Register
Name
Bits
Address
Cof.
CHANNEL0
24
0x00
R
REGISTER 9-1:
The ADC Channel Data Output register always
contains the most recent A/D conversion data. This
register is read-only. This register is latched when an
ADC read communication occurs. When a data ready
event occurs during a read communication, the most
current ADC data is also latched to avoid data
corruption issues. The three bytes of each channel are
updated synchronously at a DRCLK rate. They can be
accessed separately, if needed, but are refreshed
synchronously.
CHANNEL REGISTER
R-0
R-0
R-0
R-0
R-0
R-0
R-0
R-0
DATA_CH0
<23> (MSB)
DATA_CH0
<22>
DATA_CH0
<21>
DATA_CH0
<20>
DATA_CH0
<19>
DATA_CH0
<18>
DATA_CH0
<17>
DATA_CH0
<16>
bit 23
bit 16
R-0
R-0
R-0
R-0
R-0
R-0
R-0
R-0
DATA_CH0
<15>
DATA_CH0
<14>
DATA_CH0
<13>
DATA_CH0
<12>
DATA_CH0
<11>
DATA_CH0
<10>
DATA_CH0
<9>
DATA_CH0
<8>
bit 15
bit 8
R-0
R-0
R-0
R-0
R-0
R-0
R-0
R-0
DATA_CH0
<7>
DATA_CH0
<6>
DATA_CH0
<5>
DATA_CH0
<4>
DATA_CH0
<3>
DATA_CH0
<2>
DATA_CH0
<1>
DATA_CH0
<0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 23-0
x = Bit is unknown
DATA_CH0: Output code from ADC. This data is post-calibration if the EN_OFFCAL or EN_GAINCAL
bits are enabled. This data can be formatted in 16-/24-/32-bit modes, depending on the WIDTH_DATA<1:0> settings. (See Section 5.5 “ADC Output Coding”.)
2014 Microchip Technology Inc.
DS20005287A-page 67
MCP3918
9.2
The MOD register contains the most recent modulator
data output and is updated at a DMCLK rate. The
default value corresponds to an equivalent input of 0V
on the ADC. Each bit in this register corresponds to one
comparator output on one of the channels. This register
should not be written to ensure ADC accuracy.
MOD Register – Modulators
Output Register
Name
Bits
Address
Cof.
MOD
24
0x08
R/W
REGISTER 9-2:
MOD REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 23
bit 16
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-1
R/W-1
—
—
—
—
COMP3_CH0
COMP2_CH0
COMP1_CH0
COMP0_CH0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 23-4
Unimplemented: Read as ‘0’
bit 3-0
COMPn_CH0: Comparator Outputs from ADC
DS20005287A-page 68
x = Bit is unknown
2014 Microchip Technology Inc.
MCP3918
9.3
Any write to this register automatically resets and
restarts the active ADC.
PHASE Register – Phase
Configuration Register
Name
Bits
Address
Cof.
PHASE
24
0x0A
R/W
REGISTER 9-3:
PHASE REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 23
bit 16
U-0
U-0
U-0
U-0
—
—
—
—
R/W-0
R/W-0
PHASE<11> PHASE<10>
R/W-0
R/W-0
PHASE<9>
PHASE<8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PHASE<7>
PHASE<6>
PHASE<5>
PHASE<4>
PHASE<3>
PHASE<2>
PHASE<1>
PHASE<0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 23-12
Unimplemented: Read as ‘0’
bit 11-0
PHASE<11:0> Conversion Start delay. Delay = (PHASE<11:0> decimal code + OSR/2)/DMCLK.
2014 Microchip Technology Inc.
DS20005287A-page 69
MCP3918
9.4
GAIN Register – PGA Gain
Configuration Register
Name
Bits
Address
Cof.
GAIN
24
0x0B
R/W
REGISTER 9-4:
GAIN REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 23
bit 16
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
R/W-0
—
—
—
—
—
PGA_CH0<2>
R/W-0
R/W-0
PGA_CH0<1> PGA_CH0<0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 23-3
Unimplemented: Read as ‘0’
bit 2-0
PGA_CH0<2:0>: PGA Setting
111 = Reserved (Gain = 1)
110 = Reserved (Gain = 1)
101 = Gain is 32
100 = Gain is 16
011 = Gain is 8
010 = Gain is 4
001 = Gain is 2
000 = Gain is 1 (Default)
DS20005287A-page 70
x = Bit is unknown
2014 Microchip Technology Inc.
MCP3918
9.5
STATUSCOM Register - Status and
Communication Register
Name
Bits
Address
Cof.
STATUSCOM
24
0x0C
R/W
REGISTER 9-5:
STATUSCOM REGISTER
R/W-1
R/W-0
R/W-1
R/W-0
U-0
R/W-0
READ<1>
READ<0>
WRITE
DR_HIZ
—
WIDTH_ CRC
R/W-0
R/W-1
WIDTH_ DATA<1> WIDTH_ DATA<0>
bit 23
bit 16
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
U-0
U-0
U-0
EN_CRCCOM
EN_INT
Reserved
Reserved
EN_MDAT
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
R-1
R-1
—
—
—
—
—
—
—
DRSTATUS<0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 23-22
READ<1:0>: Address counter increment setting for Read Communication
11 = Address counter auto-increments, loops on the entire register map
10 = Address counter auto-increments, loops on register TYPES (DEFAULT)
01 = Address counter auto-increments, loops on register GROUPS
00 =
Address not incremented, continually reads the same single-register address
bit 21
WRITE: Address counter increment setting for Write Communication
1
= Address counter loops on writable part of the register map (Default)
0
= Address not incremented, continually writes to the same single-register address
bit 20
DR_HIZ: Data Ready Pin Inactive State Control
1
= The DR pin state is a logic high when data is NOT ready
0
= The DR pin state is high-impedance when data is NOT ready (Default)
bit 19
Unimplemented: Read as ‘0’
bit 18
WIDTH_CRC Format for CRC-16 on communications
1
= 32-bit (CRC-16 code is followed by sixteen zeros). This coding is compatible with CRC
implementation in most 32-bit MCUs (including PIC32 MCUs).
0
= 16-bit (default)
bit 17-16
WIDTH_DATA<1:0>: ADC Data Format Settings for the ADC (see Section 5.5 “ADC Output Coding”)
11 = 32-bit with sign extension
10 = 32-bit with zeros padding
01 = 24-bit (default)
00 = 16-bit (with rounding)
bit 15
EN_CRCCOM: Enable CRC CRC-16 Checksum on Serial communications
1
= CRC-16 Checksum is provided at the end of each communication sequence (therefore each
communication is longer). The CRC-16 Message is the complete communication sequence
(see section Section 6.9 “Securing Read Communications through CRC-16 Checksum”
for more details).
0
=Disabled (Default)
2014 Microchip Technology Inc.
DS20005287A-page 71
MCP3918
REGISTER 9-5:
STATUSCOM REGISTER (CONTINUED)
bit 14
EN_INT: Enable the CRCREG interrupt function
1
=
The interrupt flag for the CRCREG checksum verification is enabled. The Data Ready pin
(DR) will become logic low and stays logic low if a CRCREG checksum error happens. This
interrupt is cleared if the LOCK<7:0> value is made equal to the PASSWORD value (0xA5).
0
= The interrupt flag for the CRCREG checksum verification is disabled. The CRCREG<15:0>
bits are still calculated properly and can still be read in this mode.
bit 13-12
Reserved: These bits should be kept equal to '0' at all times.
bit 11
EN_MDAT: Enable Modulator Output
1
=
MDAT0 output is enabled
0
=
MDAT0 output is disabled (DEFAULT)
bit 10-1
Unimplemented: Read as ‘0’
bit 0
DRSTATUS: Data Ready status bit
DRSTATUS = 1 - Channel CH0 data is not ready (DEFAULT)
DRSTATUS = 0 - Channel CH0 data is ready. The status bit is set back to '1' after reading the
STATUSCOM register. The status bit is not set back to '1' by the read of the
corresponding channel ADC data.
DS20005287A-page 72
2014 Microchip Technology Inc.
MCP3918
9.6
CONFIG0 Register Configuration Register 0
Name
Bits
Address
Cof.
CONFIG0
24
0x0D
R/W
REGISTER 9-6:
CONFIG0 REGISTER
R/W-0
R/W-0
R/W-1
R/W-1
R/W-1
R/W-0
R/W-0
R/W-0
EN_OFFCAL
EN_GAINCAL
DITHER<1>
DITHER<0>
BOOST<1>
BOOST<0>
PRE<1>
PRE<0>
bit 23
bit 16
R/W-0
R/W-1
R/W-1
U-0
U-0
U-0
U-0
U-0
OSR<2>
OSR<1>
OSR<0>
—
—
—
—
—
bit 15
bit 8
R/W-0
R/W-1
R/W-0
R/W-1
R/W-0
R/W-0
R/W-0
R/W-0
VREFCAL<7>
VREFCAL<6>
VREFCAL<5>
VREFCAL<4>
VREFCAL<3>
VREFCAL<2>
VREFCAL<1>
VREFCAL<0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 23
EN_OFFCAL: Enables the 24-bit digital offset error calibration on all channels
1
= Enabled. This mode does not add any group delay to the ADC data.
0 = Disabled (Default)
bit 22
EN_GAINCAL: Enables or disables the 24-bit digital gain error calibration on all channels
1 = Enabled. This mode adds a group delay on all channels of 24 DMCLK periods. All Data Ready
pulses are delayed by 24 clock periods, compared to the mode with EN_GAINCAL = 0.
0 = Disabled (Default)
bit 21-20
DITHER<1:0>: Control for dithering circuit for idle tones cancellation and improved THD on all channels
11 = Dithering ON, Strength = Maximum (Default)
10 = Dithering ON, Strength = Medium
01 = Dithering ON, Strength = Minimum
00 = Dithering turned OFF
bit 19-18
BOOST<1:0>: Bias Current Selection for the ADC (impacts achievable maximum sampling speed, see
Table 5-2)
11 = All channels have current x 2
10 = All channels have current x 1 (Default)
01 = All channels have current x 0.66
00 = All channels have current x 0.5
bit 17-16
PRE<1:0> Analog Master Clock (AMCLK) Prescaler Value
11 = AMCLK = MCLK/8
10 = AMCLK = MCLK/4
01 = AMCLK = MCLK/2
00 = AMCLK = MCLK (Default)
2014 Microchip Technology Inc.
DS20005287A-page 73
MCP3918
REGISTER 9-6:
CONFIG0 REGISTER (CONTINUED)
bit 15-13
OSR<2:0> Oversampling Ratio for delta-sigma A/D Conversion (ALL CHANNELS, fD/fS)
111 = 4096 (fD = 244 sps for MCLK = 4 MHz, fS = AMCLK = 1 MHz)
110 = 2048 (fD = 488 sps for MCLK = 4 MHz, fS = AMCLK = 1 MHz)
101 = 1024 (fD = 976 sps for MCLK = 4 MHz, fS = AMCLK = 1 MHz)
100 = 512 (fD = 1.953 ksps for MCLK = 4 MHz, fS = AMCLK = 1 MHz)
011 = 256 (fD = 3.90625 ksps for MCLK = 4 MHz, fS = AMCLK = 1 MHz) (Default)
010 = 128 (fD = 7.8125 ksps for MCLK = 4 MHz, fS = AMCLK = 1 MHz)
001 = 64 (fD = 15.625 ksps for MCLK = 4 MHz, fS = AMCLK = 1 MHz)
000 = 32 (fD = 31.25 ksps for MCLK = 4 MHz, fS = AMCLK = 1 MHz)
bit 12-8
Unimplemented: Read as ‘0’
bit 7-0
VREFCAL<7:0>:
DS20005287A-page 74
Internal Voltage Temperature coefficient VREFCAL<7:0> value. (See
Section 5.6.3 “Temperature Compensation (VREFCAL<7:0>)” for complete
description).
2014 Microchip Technology Inc.
MCP3918
9.7
CONFIG1 Register –
Configuration Register 1
Name
Bits
Address
Cof.
CONFIG1
24
0x0E
R/W
REGISTER 9-7:
CONFIG1 REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0
—
—
—
—
—
—
—
RESET<0>
bit 23
bit 16
U-0
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0
—
—
—
—
—
—
—
SHUTDOWN<0>
bit 15
bit 8
R/W-0
R/W-1
U-0
U-0
U-0
U-0
U-0
U-0
VREFEXT
CLKEXT
—
—
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 23-17
Unimplemented: Read as ‘0’
bit 16
RESET<0>: Soft Reset mode setting for the ADC
= ADC Channel in Soft Reset mode
= ADC Channel not in Soft Reset mode
bit 15-9
Unimplemented: Read as ‘0’
bit 8
SHUTDOWN<0>: Shutdown mode setting for the ADC
= ADC Channel in Shutdown mode
= ADC Channel not in Shutdown mode
bit 7
VREFEXT: Internal Voltage Reference selection bit
1 = Internal Voltage Reference Disabled. An external reference voltage needs to be applied across the
REFIN+/- pins. The analog power consumption (AIDD) is slightly diminished in this mode since the
internal voltage reference is placed in Shutdown mode.
0 = Internal Reference enabled. For optimal accuracy, the REFIN+/OUT pin needs proper decoupling
capacitors. REFIN- pin should be connected to AGND, when in this mode.
bit 6
CLKEXT: Internal Clock selection bit
1 = MCLK is generated externally and should be provided on OSC1 pin: the crystal oscillator is disabled
and consumes no current (Default)
0 = Crystal oscillator enabled. A crystal must be placed between OSC1 and OSC2 with proper
decoupling capacitors. The digital power consumption (DIDD) is increased in this mode due to the
oscillator.
bit 5-0
Unimplemented: Read as ‘0’
2014 Microchip Technology Inc.
DS20005287A-page 75
MCP3918
9.8
OFFCAL_CH0 and GAINCAL_CH0
Registers – Digital Offset And
Gain Error Calibration Registers
Name
Bits
Address
Cof.
OFFCAL_CH0
24
0x0F
R/W
GAINCAL_CH0
24
0x10
R/W
REGISTER 9-8:
R/W-0
OFFCAL_CH0
<23>
OFFCAL_CH0 REGISTER
R/W-0
R/W-0
OFFCAL_CH0 OFFCAL_CH0
<22>
<21>
...
R/W-0
...
OFFCAL_CH0
<3>
R/W-0
R/W-0
OFFCAL_CH0 OFFCAL_CH0
<2>
<1>
R/W-0
OFFCAL_CH0
<0>
bit 23
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 23-0
x = Bit is unknown
OFFCAL_CH0: Digital Offset calibration value for the corresponding channel CH0. This register is
simply added to the output code of the channel bit by bit. This register is 24-bit two's
complement MSB first coding. CH0 Output Code = OFFCAL_CH0 + ADC CH0 Output
Code. This register is a Don't Care if EN_OFFCAL = 0 (Offset calibration disabled), but
its value is not cleared by the EN_OFFCAL bit.
REGISTER 9-9:
R/W-0
GAINCAL_CH0 REGISTER
R/W-0
R/W-0
GAINCAL_CH0
GAINGAINCAL_CH0
<23>
CAL_CH0<22>
<21>
...
...
R/W-0
R/W-0
R/W-0
R/W-0
GAINCAL_CH0 GAINCAL_CH0 GAINCAL_CH0 GAINCAL_CH0
<3>
<2>
<1>
<0>
bit 23
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 23-0
x = Bit is unknown
GAINCAL_CH0: Digital gain error calibration value for the corresponding channel CH0. This register
is signed 24-bit MSB first format with a range of -1x to +0.9999999x (from 0x80000
to 0x7FFFFF). The gain calibration adds 1x to this register and multiplies it to the
output code of the channel bit by bit, after offset calibration. The range of the gain
calibration is thus from 0x to 1.9999999x (from 0x80000 to 0x7FFFFF). The LSB
corresponds to a 2-23 increment in the multiplier.
ADC Output Code = (GAINCAL_CH0+1)*ADC CH0 Output Code. This register is a
Don't Care if EN_GAINCAL = 0 (Gain calibration disabled) but its value is not
cleared by the EN_GAINCAL bit.
DS20005287A-page 76
2014 Microchip Technology Inc.
MCP3918
9.9
SECURITY Register – Password
and CRC-16 on Register Map
Name
Bits
Address
Cof.
LOCK/CRC
24
0x1F
R/W
REGISTER 9-10:
LOCK/CRC REGISTER
R/W-1
R/W-0
R/W-1
R/W-0
R/W-0
R/W-1
R/W-0
R/W-1
LOCK<7>
LOCK<6>
LOCK<5>
LOCK<4>
LOCK<3>
LOCK<2>
LOCK<1>
LOCK<0>
bit 23
bit 16
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CRCREG<15>
CRCREG<14>
CRCREG<13>
CRCREG<12>
CRCREG<11>
CRCREG<10>
CRCREG<9>
CRCREG<8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CRCREG<7>
CRCREG<6>
CRCREG<5>
CRCREG<4>
CRCREG<3>
CRCREG<2>
CRCREG<1>
CRCREG<0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 23-16
LOCKn<7:0>: Lock Code for the writable part of the register map
LOCK<7:0> = PASSWORD = 0xA5 (Default value): The entire register map is writable. The
CRCREG<15:0> bits and the CRC Interrupt are cleared. No CRC-16 checksum on
register map is calculated.
LOCK<7:0> different from 0xA5: The only writable register is the LOCK/CRC register. All other registers
will appear as undefined while in this mode. The CRCREG checksum is calculated
continuously and can generate interrupts if the CRC Interrupt EN_INT bit has been
enabled. If a write to a register needs to be performed, the user needs to unlock the register
map beforehand, by writing 0xA5 to the LOCK<7:0> bits.
bit 15-0
CRCREG<15:0>:
2014 Microchip Technology Inc.
CRC-16 Checksum that is calculated with the writable part of the register map as
a message. This is a read-only 16-bit code. This checksum is continuously
recalculated and updated every 10 DMCLK periods. It is reset to its default value
(0x0000) when LOCK<7:0> = 0xA5.
DS20005287A-page 77
MCP3918
NOTES:
DS20005287A-page 78
2014 Microchip Technology Inc.
MCP3918
10.0
PACKAGING INFORMATION
10.1
Package Marking Information
20-Lead QFN (4x4x0.9 mm)
PIN 1
Example
PIN 1
20-Lead SSOP (5.30 mm)
3918
A1
E/ML e^^3
415256
Example
MCP3918A1
E/SS e
^^3
1415256
Legend: XX...X
Y
YY
WW
NNN
e3
*
Note:
Customer-specific information
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
2014 Microchip Technology Inc.
DS20005287A-page 79
MCP3918
&
!! " # $%
= & ' !&" & +# *!( !!& + %& &#&
&& <>>***' '> +
D
D2
EXPOSED
PAD
e
E2
2
E
b
2
1
1
K
N
N
NOTE 1
TOP VIEW
L
BOTTOM VIEW
A
A1
A3
?&!
'! @'&!
E"') %!
@@- -
E
E
EJ
K
&
J M &
Q
&# %%
/
; &&
+!!
,
J U#&
-
-$
-
!##U#&
J @&
-$
!##@&
/:;
-=
:;
V
Q
:;
V
Q
; &&U#&
)
Q
/
,
; &&@&
@
,
/
X
Y
Y
; &&& -$
!##
&
!"#$%&" ' ()"&'"!&) &#*& & & # +!!*!"&#
, '! #& -./
:;< :!'! &$&"! **& "&& !
-=< % '! ("!"*& "&& (% % '& " !! DS20005287A-page 80
* ;V:
2014 Microchip Technology Inc.
MCP3918
&
= & ' !&" & +# *!( !!& + %& &#&
&& <>>***' '> +
2014 Microchip Technology Inc.
DS20005287A-page 81
MCP3918
&
'()* '! + * '' ,- !! " # $''+ %
= & ' !&" & +# *!( !!& + %& &#&
&& <>>***' '> +
D
N
E
E1
NOTE 1
1 2
e
b
c
A2
A
φ
A1
L1
?&!
'! @'&!
E"') %!
L
@@- -
E
E
EJ
K
&
J M &
Y
Y
V/
/
Q/
&# %%
/
Y
Y
J U#&
-
Q
Q
##+U#&
-
/
/,
/V
J @&
V
/
//
/
/
##+
+!!
=
&@&
@
=
& &
@
@#
=
+!!
&
@#U#&
V/:;
/-=
Y
Z
Z
/
QZ
)
Y
,Q
&
!"#$%&" ' ()"&'"!&) &#*& & & # '! !#-# &"#' #%! & "! ! #%! & "! !! &$#'' !#
, '! #& -./
:;< :!'! &$&"! **& "&& !
-=< % '! ("!"*& "&& (% % '& " !! DS20005287A-page 82
* ;:
2014 Microchip Technology Inc.
MCP3918
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2014 Microchip Technology Inc.
DS20005287A-page 83
MCP3918
NOTES:
DS20005287A-page 84
2014 Microchip Technology Inc.
MCP3918
APPENDIX A:
REVISION HISTORY
Revision A (May 2014)
• Original Release of this Document.
2014 Microchip Technology Inc.
DS20005287A-page 85
MCP3918
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
X
PART NO.
XX
Device
Address
Options
X
Tape and Temperature
Reel
Range
/XX
Package
Device:
MCP3918A1: One Channel Analog Font End Converter
Address Options:
XX
A6
A5
A0
=
0
0
A1*
=
0
1
A2
=
1
0
A3
=
1
1
* Default option. Contact Microchip factory for other
address options
Tape and Reel:
T
= Tape and Reel
Temperature Range:
E
= -40°C to +125°C
Package:
ML = 20-Lead Plastic Quad Flat, No Lead Package –
4x4 mm Body with 0.40 mm Contact Length
(QFN)
Examples:
a)
MCP3918A1-E/ML:
b)
MCP3918A1T-E/ML:
a)
MCP3918A1-E/SS:
b)
MCP3918A1T-E/SS:
Address Option A1,
Extended Temperature,
20LD QFN package
Address Option A1,
Tape and Reel,
Extended Temperature,
20LD QFN package
Address Option A1,
Extended Temperature,
20LD SSOP package
Address Option A1,
Tape and Reel,
Extended Temperature,
20LD SSOP package
SS = 20-Lead Plastic Shrink Small Outline – 5.30
mm Body (SSOP)
2014 Microchip Technology Inc.
DS20005287A-page 86
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro,
PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash
and UNI/O are registered trademarks of Microchip Technology
Incorporated in the U.S.A. and other countries.
FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,
MTP, SEEVAL and The Embedded Control Solutions
Company are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Silicon Storage Technology is a registered trademark of
Microchip Technology Inc. in other countries.
Analog-for-the-Digital Age, Application Maestro, BodyCom,
chipKIT, chipKIT logo, CodeGuard, dsPICDEM,
dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial
Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB
Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code
Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit,
PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O,
Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA
and Z-Scale are trademarks of Microchip Technology
Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
GestIC and ULPP are registered trademarks of Microchip
Technology Germany II GmbH & Co. KG, a subsidiary of
Microchip Technology Inc., in other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2014, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
ISBN: 978-1-63276-214-6
QUALITY MANAGEMENT SYSTEM
CERTIFIED BY DNV
== ISO/TS 16949 ==
2014 Microchip Technology Inc.
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
DS20005287A-page 87
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2943-5100
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
Austin, TX
Tel: 512-257-3370
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Novi, MI
Tel: 248-848-4000
Houston, TX
Tel: 281-894-5983
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
Canada - Toronto
Tel: 905-673-0699
Fax: 905-673-6509
DS20005287A-page 88
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
China - Hangzhou
Tel: 86-571-8792-8115
Fax: 86-571-8792-8116
China - Hong Kong SAR
Tel: 852-2943-5100
Fax: 852-2401-3431
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
China - Shenzhen
Tel: 86-755-8864-2200
Fax: 86-755-8203-1760
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
India - Pune
Tel: 91-20-3019-1500
Japan - Osaka
Tel: 81-6-6152-7160
Fax: 81-6-6152-9310
Japan - Tokyo
Tel: 81-3-6880- 3770
Fax: 81-3-6880-3771
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Germany - Dusseldorf
Tel: 49-2129-3766400
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Germany - Pforzheim
Tel: 49-7231-424750
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Italy - Venice
Tel: 39-049-7625286
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
Poland - Warsaw
Tel: 48-22-3325737
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Sweden - Stockholm
Tel: 46-8-5090-4654
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
Taiwan - Kaohsiung
Tel: 886-7-213-7830
Taiwan - Taipei
Tel: 886-2-2508-8600
Fax: 886-2-2508-0102
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
03/25/14
2014 Microchip Technology Inc.