NCP5395T 2/3/4-Phase Controller with On Board Gate Drivers for CPU Applications The NCP5395T provides up to a four−phase buck solution which combines differential voltage sensing, differential phase current sensing, and adaptive voltage positioning to provide accurately regulated power for both Intel and AMD processors. It also receives power saving command (PSI) from CPU, and operates in a single phase emulation diode mode to obtain a high efficiency at light load. Dual−edge pulse−width modulation (PWM) combined with precise inductor current sensing provides the fastest initial response to dynamic load events both in power saving and normal modes. Dual−edge multiphase modulation reduces the total bulk and ceramic output capacitance required therefore reducing the system cost to meet transient regulation specifications. The on board gate drivers includes adaptive non overlap and power saving operation. A high performance operational error amplifier is provided to simplify compensation of the system. Patented Dynamic Reference Injection further simplifies loop compensation by eliminating the need to compromise between closed−loop transient response and Dynamic VID performance. • • 1 48 MARKING DIAGRAM 48 1 NCP5395T AWLYYWWG A WL YY WW G = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package Meets Intel’s VR11.1 and AMD’s 6 Bit Code Specifications Enhanced Power Saving Function 48 1 Internal Soft Start BG1 BG3 G4 PSI Dual−edge PWM for Fastest Initial Response to Transient Loading VRRDY VID0 EN VID1 High Performance Operational Error Amplifier CS1N VID2 AGND CS1P VID3 Down−bonded to Dynamic Reference Injection (Patent #US07057381) CS2N VID4 CS2P Exposed Flag VID5 DAC Range from 0.5 V to 1.6 V CS3N VID6 CS3P VID7/AMD DAC Feed Forward Function (Patient Pending) CS4N ROSC CS4P ILIM ±0.5% DAC Voltage Accuracy from 1.0 V to 1.6 V True Differential Remote Voltage Sensing Amplifier Phase−to−Phase Current Balancing “Lossless” Differential Inductor Current Sensing ORDERING INFORMATION Accurate Current Monitoring (IMON) Device Package Shipping† Differential Current Sense Amplifiers for Each Phase Adaptive Voltage Positioning (AVP) NCP5395TMNR2G QFN48 2500/Tape & Reel (Pb−Free) Oscillator Frequency Range of 125 kHz − 1 MHz Latched Over Voltage Protection (OVP) †For information on tape and reel specifications, including part orientation and tape sizes, please Guaranteed Startup into Pre−Charged Loads refer to our Tape and Reel Packaging Specifications Threshold Sensitive Enable Pin for VTT Sensing Brochure, BRD8011/D. Power Good Output with Internal Delays • Thermal Shutdown Protection Output Disable Control Turn Off of Both Phase Pair • This is a Pb−Free Device MOSFETs Applications Thermally Compensated Current Monitoring • Desktop Processors Adaptive−Non−Overlap Gate Drive Circuit © Semiconductor Components Industries, LLC, 2013 July, 2013 − Rev. 1 IMON VSP VSN DIFFOUT COMP VFB VDRP VDFB CSSUM DAC 12VMON VCC • • • • • • • • • • • • • • • • • • • • • QFN48, 7x7 CASE 485AJ VBST3 TG3 SWN3 DRVON BST2 TG2 SWN2 BG2 VCCP SWN1 TG1 BST1 Features http://onsemi.com 1 Publication Order Number: NCP5395T/D NCP5395T VID0 VID1 VID2 VID3 VID4 VID5 VID6 VID7/AMD Flexible DAC + PSI VCCP Overvoltage Protection BST1 DAC + VSN - + VSP Phase 1 Gate Driver with Adaptive Non−overlap Diff Amp TG1 SWN1 BG1 DIFFOUT 1.3 V Error Amp + - VFB BST2 Phase 2 Gate Driver with Adaptive Non−overlap + COMP VDRP - + - VDFB −2/3 CSSUM CS1P CS1N CS2P CS2N CS3P CS3N CS4P CS4N TG2 SWN2 BG2 + + + - + + - + Gain = 6 BST3 + Gain = 6 Phase 3 Gate Driver with Adaptive Non−overlap + + - Gain = 6 + + TG3 SWN3 BG3 G4 - Gain = 6 Oscillator IMON ROSC DRVON + - ILIM EN VCC 4.25 V + - ILimit Control, Fault Logic and Monitor Circuits 12VMON VR_RDY UVLO GND (FLAG) Figure 1. NCP5395T Functional Block Diagram http://onsemi.com 2 NCP5395T VTT PSI#_CPU VID0 VID1 VID2 VID3 VID4 VID5 VID6 VID7 12V_FILTER 2 1 12V_FILTER D G S IMON 12 11 10 9 8 7 6 5 4 3 2 1 D ILIM ROSC VID7 VID6 VID5 VID4 VID3 VID2 VID1 VID0 PSI BG3 VCCP RFB CFB 13 IMON 14 VSP 15 16 RF RFB CH RDRP CDFB RDFB RISO RT 12V_FILTER 17 18 CF RISO VBST3 19 20 R 21 22 23 VDRP VDFB DRVON 45 NCP5395T 48L 7x7 QFN FLAG = GND TG2 43 SWN2 42 12V_FILTER BG2 12V_FILTER 41 VCCP 40 DAC SWN1 39 2 1 D G TG1 38 CS4P CS4N CS3P CS3N CS2P CS2N CS1P CS1N EN VR_RDY G4 BG1 24 VCC PWM3_SENSE_P DRVON BST2 44 CSSUM 12VMON S 48 SWN3 46 DIFFOUT VFB PWM3_SENSE_N G S TG3 47 VSN COMP D G 25 26 27 28 29 30 31 32 33 34 35 36 BST1 S 37 D D C17 G G +5.0V S VTT S PWM1_SENSE_N PWM1_SENSE_P VCCP PWM1_SENSE_P PWM1_SENSE_N ENABLE PWM3_SENSE_P PWM3_SENSE_N Figure 2. Typical 2 Phase Application http://onsemi.com 3 NCP5395T VTT R236 PSI#_CPU VID0 VID1 VID2 VID3 VID4 VID5 VID6 VID7 12V_FILTER 12V_FILTER 2 1 D G S D D G PWM3_SENSE_N G S PWM3_SENSE_P ILIM ROSC VID7 VID6 VID5 VID4 VID3 VID2 VID1 VID0 PSI BG3 12 11 10 9 8 7 6 5 4 3 2 1 S VCCP RFB CFB VBST3 13 IMON 14 VSP TG3 15 VSN RF RFB CH 16 DIFFOUT 17 18 CF RDRP 19 CDFB RDFB RT RISO RISO 12V_FILTER SWN3 COMP VFB DRVON NCP5395T 48L 7x7 QFN FLAG = GND BST2 TG2 VDRP SWN2 20 VDFB BG2 R 21 CSSUM 22 DAC 23 12VMON SWN1 TG1 CS4P CS4N CS3P CS3N CS2P CS2N CS1P CS1N EN VR_RDY G4 BG1 24 VCC VCCP 25 26 27 28 29 30 31 32 33 34 35 36 BST1 12V_FILTER 48 2 47 1 D 46 45 G S DRVON 44 43 D D S S 41 12V_FILTER PWM2_SENSE_N G G 42 40 39 PWM2_SENSE_P 12V_FILTER 38 2 1 37 D G S C37 VCCP +5.0V D D G VTT PWM1_SENSE_P G S S PWM1_SENSE_N PWM1_SENSE_P PWM1_SENSE_N PWM2_SENSE_P ENABLE PWM2_SENSE_N PWM3_SENSE_P PWM3_SENSE_N Figure 3. Typical 3 Phase Application http://onsemi.com 4 12V_FILTER NCP5395T VTT PSI#_CPU VID0 VID1 VID2 VID3 VID4 VID5 VID6 VID7 12V_FILTER 2 1 12V_FILTER D G S D D G PWM3_SENSE_N G S PWM3_SENSE_P S 12 11 10 9 8 7 6 5 4 3 2 1 IMON 15 RFB RF 16 17 CH 18 RDRP 19 CDFB 20 RDFB 21 RT 22 RISO RISO TG3 VSN SWN3 DIFFOUT COMP VFB DRVON NCP5395T 48L 7x7 QFN FLAG = GND 2 47 1 D 46 G 45 DRVON S BST2 44 43 TG2 VDRP SWN2 VDFB BG2 CSSUM VCCP DAC SWN1 23 12VMON VCC 24 48 TG1 BST1 D D G 42 S 41 12V_FILTER 40 PWM2_SENSE_N G PWM2_SENSE_P S 12V_FILTER 39 38 2 1 37 D G S 25 26 27 28 29 30 31 32 33 34 35 36 12V_FILTER VBST3 13 IMON 14 VSP CS4P CS4N CS3P CS3N CS2P CS2N CS1P CS1N EN VR_RDY G4 BG1 RFB CFB CF 12V_FILTER ILIM ROSC VID7 VID6 VID5 VID4 VID3 VID2 VID1 VID0 PSI BG3 VCCP VCCP VTT ENABLE D D +5.0V PWM4_GATE G PWM1_SENSE_P S PWM3_SENSE_N DRVON PWM4_GATE PWM4_SENSE_P 12V_FILTER D VCC BST 4 1 DRH 8 OD 7 SW 3 IN 5 DRL 2 PGND 6 NCP5359 PWM4_SENSE_N Figure 4. Typical 4 Phase Application http://onsemi.com 5 PWM1_SENSE_P S PWM1_SENSE_N 12V_FILTER PWM2_SENSE_P 2 1 PWM2_SENSE_N PWM3_SENSE_P PWM1_SENSE_N G G S D D G PWM4_SENSE_N G S S PWM4_SENSE_P NCP5395T Table 1. Pin Descriptions Pin No. Symbol Description 1 BG3 Low side gate drive #3 2 PSI Power Saving Control. Low = single phase operation; High = normal operation 3 VID0 Voltage ID DAC input 4 VID1 Voltage ID DAC input 5 VID2 Voltage ID DAC input 6 VID3 Voltage ID DAC input 7 VID4 Voltage ID DAC input 8 VID5 Voltage ID DAC input 9 VID6 Voltage ID DAC input 10 VID7/AMD Voltage ID DAC input. Pull to VCC (5 V) to enable AMD 6−bit DAC code. 11 ROSC A resistance from this pin to ground programs the oscillator frequency and provides a 2 V reference for programming the ILIM voltage. 12 ILIM Over current shutdown threshold setting. ILIM = VDRP − 1.3 V. Resistor divide ROSC to set threshold 13 IMON 0 to 1.1 V analog signal proportional to the output load current. VSN referenced Clamped to 1.1 Vmax 14 VSP Non−inverting input to the internal differential remote sense amplifier 15 VSN Inverting input to the internal differential remote sense amplifier 16 DIFFOUT Output of the differential remote sense amplifier 17 COMP Output of the compensation amplifier 18 VFB Compensation amplifier voltage feedback 19 VDRP Voltage output signal proportional to current used for current limit and output voltage droop 20 VDFB Droop Amplifier Voltage Feedback 21 CSSUM Inverted Sum of the Differential Current Sense inputs 22 DAC DAC output used to provide feed forward for dynamic VID 23 12VMON Monitor a 12 V input through a resistor divider 24 VCC Power for the internal control circuits with UVLO monitor 25 CS4P Non−inverting input to current sense amplifier #4 26 CS4N Inverting input to current sense amplifier #4 27 CS3P Non−inverting input to current sense amplifier #3 28 CS3N Inverting input to current sense amplifier #3 29 CS2P Non−inverting input to current sense amplifier #2 30 CS2N Inverting input to current sense amplifier #2 31 CS1P Non−inverting input to current sense amplifier #1 32 CS1N Inverting input to current sense amplifier #1 33 EN Threshold sensitive input. High = startup, Low =shutdown. 34 VR_RDY Open collector output. High indicates that the output is regulating 35 G4 PWM output pulse to gate driver. 36 BG1 Low side gate drive #1 37 BST1 Upper MOSFET floating bootstrap supply for driver#1 38 TG1 High side gate drive #1 39 SWN1 Switch Node #1 40 VCCP Power VCC for gate drivers with UVLO monitor 41 BG2 Low side gate drive #2 42 SWN2 Switch Node #2 43 TG2 High side gate drive #2 44 BST2 Upper MOSFET floating bootstrap supply for driver#2 45 DRVON Bidirectional Gate Drive Enable 46 SWN3 Switch Node #3 47 TG3 High side gate drive #3 48 BST3 Upper MOSFET floating bootstrap supply for driver#3 FLAG GND Power supply return (QFN Flag) http://onsemi.com 6 NCP5395T ABSOLUTE MAXIMUM RATINGS Rating Symbol Value Unit Controller Power Supply Voltages to GND VCC −0.3, 7 V Driver Power Supply Voltages to GND VCCP −0.3, 15 V High−Side Gate Driver Supplies: BSTx to SWNx VBST − VSWN 35 V wrt/GND 40 V ≤ 50 ns wrt/GND −0.3, 15 wrt/SWN V High−Side FET Gate Driver Voltages: TGx to SWNx VTG − VSWN BOOT + 0.3 V 35 V ≤ 50 ns wrt/GND −0.3, 15 wrt/SWN −5 V (200 ns) V VSWN 35 40 V ≤ 50 ns wrt/GND −5 VDC −10 V (200 ns) V VBG − AGND VCC + 0.3 V −5 V (200 ns) V VLOGIC −0.3, 6 V VGND 0 V GND ±300 mV 1.1 V −0.3, 5.5 V 30.5 °C/W ELECTRICAL INFORMATION Switch Node: SWNx Low−Side Gate Drive: BGx Logic Inputs GND V− Imon Out VIMON All Other Pins THERMAL INFORMATION Thermal Characteristic QFN Package (Note 1) RqJA Operating Junction Temperature Range (Note 2) TJ 0 to 125 °C Operating Ambient Temperature Range TAMB 0 to +70 °C Maximum Storage Temperature Range TSTG −55 to +150 °C Moisture Sensitivity Level QFN Package MSL 1 Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. *All signals referenced to GND unless noted otherwise. *The maximum package power dissipation must be observed. 1. JESD 51−5 (1S2P Direct−Attach Method) with 0 LFM 2. Operation at −40°C to 0°C guaranteed by design, not production tested. http://onsemi.com 7 NCP5395T ELECTRICAL CHARACTERISTICS 0°C < TA < 70°C; 0°C < TJ < 125°C; 4.75 < VCC < 5.25 V; All DAC Codes; CVCC = 0.1 mF unless otherwise noted. Parameter Test Conditions Min Typ Max Unit ERROR AMPLIFIER Open Loop DC Gain CL = 60 pF to GND, RL = 10 kW to GND − 100 − dB Open Loop Unity Gain Bandwidth CL = 60 pF to GND, RL = 10 kW to GND − 18 − MHz Open Loop Phase Margin CL = 60 pF to GND, RL = 10 kW to GND − 70 − ° Slew Rate DVin = 100 mV, G = −10V/V, DVout = 1.5 V − 2.5 V, CL = 60 pF to GND, DC Load = ±125 mA to GND − 10 − V/ms Maximum Output Voltage 10 mV of Overdrive, ISOURCE = 2.0 mA 3.0 − − V Minimum Output Voltage 10 mV of Overdrive, ISINK = 500 mA − − 75 mV Output Source Current 10 mV of Overdrive, Vout = 3.5 V 1.5 2.0 − mA Output Sink Current 10 mV of Overdrive, Vout = 0.1 V 0.65 1.0 − mA DIFFERENTIAL SUMMING AMPLIFIER V+ Input Pull down Resistance DRVON = low DRVON = high − − 0.6 6.0 − − kW V+ Input Bias Voltage DRVON = low DRVON = high − 0.8 0.05 0.88 0.1 0.95 V −0.3 − 3.0 V − 15 − MHz Input Voltage Range (Note 3) −3 dB Bandwidth CL = 80 pF to GND, RL = 10 kW to GND Closed Loop DC gain VS to Diffout VS+ to VS− = 0.5 V to 1.6 V 0.98 1.0 1.02 V/V Maximum Output Voltage 10 mV of Overdrive, ISOURCE = 2 mA 3.0 − − V Minimum Output Voltage 10 mV of Overdrive, ISINK = 1 mA − − 0.5 V Output Source Current 10 mV of Overdrive, Vout = 3 V 1.5 2.0 − mA Output Sink Current 10 mV of Overdrive, Vout = 0.2 V 1.0 1.5 − mA −2 0 +2 mV INTERNAL OFFSET VOLTAGE Offset Voltage to the (+) Pin of the Error Amp & the VDRP Pin 3. Design guaranteed. http://onsemi.com 8 NCP5395T ELECTRICAL CHARACTERISTICS 0°C < TA < 70°C; 0°C < TJ < 125°C; 4.75 < VCC < 5.25 V; All DAC Codes; CVCC = 0.1 mF unless otherwise noted. Parameter Test Conditions Min Typ Max Unit VDROOP AMPLIFIER Inverting Voltage Range 0 1.3 3.0 V Open Loop DC Gain CL = 20 pF to GND including ESD RL = 1 kW to GND − 100 − dB Open Loop Unity Gain Bandwidth CL = 20 pF to GND including ESD RL = 1 kW to GND − 18 − MHz Open Loop Phase Margin CL = 20 pF to GND including ESD RL = 1 kW to GND − 70 − ° Slew Rate CL = 20 pF to GND including ESD RL = 1 kW to GND − 10 − V/ms Maximum Output Voltage 10 mV of Overdrive, ISOURCE = 4.0 mA 3.0 − − V Minimum Output Voltage 10 mV of Overdrive, ISINK = 1.0 mA − − 1.0 V Output Source Current 10 mV of Overdrive, Vout = 3.0 V 4.0 − − mA Output Sink Current 10 mV of Overdrive, Vout = 1.0 V 1.0 − − mA Current Sense Input to VDRP −3 dB Bandwidth CL = 10 pF to GND, RL = 10 kW to GND − 12 − MHz Current Summing Amp Output Offset Voltage CSx − CSNx = 0, CSx = 1.1 V −13 − 8.0 mV Maximum CSSUM Output Voltage CSx − CSxN = −0.2 V (all phases) ISOURCE = 1 mA 3.0 − − V Minimum CSSUM Output Voltage CSx − CSxN = 0.7 V (all phases) ISINK = 1 mA − − 0.3 V Output Source Current Vout = 3.0 V 1.0 − − mA Output Sink Current Vout = 0.3 V 4.0 − − mA − − 1.0 mA 450 600 770 mV − 100 − ns 3.0 − − V CSSUM AMPLIFIER PSI Enable High Input Leakage Current External 1k Pull−up to 3.3 V Threshold Delay DRVON Output High Voltage Sourcing 500 mA Output Low Voltage Sinking 500 mA − − 0.7 V Delay Time Propagation delays − 10 − ns Rise Time CL (PCB) = 20 pF, DVo = 10% to 90% − 10 − ns Fall Time CL (PCB) = 20 pF, DVo = 10% to 90% − 10 − ns Internal Pull−Down Resistance 35 70 140 kW VCC Voltage when DRVON Output Valid − − 2.0 V −50 − 50 nA −0.3 − 2.0 V −120 − 120 mV −2.5 − 2.5 mV CURRENT SENSE AMPLIFIERS Input Bias Current CSx = CSxN = 1.4 V Common Mode Input Voltage Range Differential Mode Input Voltage Range Current Sharing Offset CS1 to CSx (Note 3) all VIOS http://onsemi.com 9 NCP5395T ELECTRICAL CHARACTERISTICS 0°C < TA < 70°C; 0°C < TJ < 125°C; 4.75 < VCC < 5.25 V; All DAC Codes; CVCC = 0.1 mF unless otherwise noted. Parameter Test Conditions Min Typ Max Unit CURRENT SENSE AMPLIFIERS Current Sense Input to PWM Gain 0 V < CSx − CSxN < 0.1 V, 5.45 5.75 6.05 V/V Current Sense Input to CSSUM Gain 0 V < CSx − CSxN < 0.1 V −3.834 −3.7 −3.574 V/V VDRP to IMON Gain 1.325 V > VDRP > 1.75 V 1.965 − 2.02 V/V Current Sense Input to VDRP −3 dB Bandwidth CL = 30 pF to GND, RL = 100 kW to GND − 4.0 − MHz Output Referred Offset Voltage VDRP = 1.5 V, ISOURCE = 0 mA 0 25 50 mV Minimum Output Voltage VDRP = 1.3 V, ISINK = 25 mA − − 0.1 V Maximum Output Voltage Iout = 300 mA 1.0 − − V Output Sink Current Vout = 0.3 V 175 − − mA Maximum Clamp Voltage IMON − VSN VDRP = HIGH RLOAD = Open 1.1 − 1.2 V 100 − 1100 kHz − − 5.0 % IMON OSCILLATOR Switching Frequency Range Switching Frequency Accuracy 200 kHz < FSW < 600 kHz Switching Frequency Accuracy 100 kHz < FSW < 1 MHz − − 10 % Switching Frequency Accuracy (2ph or 4ph) ROSC = 16.2k 454 − 502 kHz Switching Frequency Accuracy (3ph) ROSC = 16.2k 468 − 518 kHz 1.93 2.00 2.05 V − 30 − ns − 1.1 − V ROSC Output Voltage MODULATORS (PWM Comparators) Minimum Pulse Width Fsw = 800 kHz Magnitude of the PWM Ramp 0% Duty Cycle COMP Voltage when the PWM Outputs Remain LO 50 250 400 mV 100% Duty Cycle COMP Voltage when the PWM Outputs Remain HI 1.1 1.35 1.6 V PWM Phase Angle Error Between Adjacent Phases −15 − 15 ° VR_RDY (Power Good) OUTPUT VR_RDY Output Saturation Voltage IPGD = 10 mA − − 0.4 V VR_RDY Rise Time (Note 3) External pull−up of 1 KW to 1.25 V, CTOT = 45 pF, DVo = 10% to 90% − 100 150 ns VR_RDY Output Voltage at Power−up VR_RDY pulled up to 5 V via 2 kW, tR(VCC) ≤ 3 x tR(5V) 100 ms ≤ tR(VCC) ≤ 20 ms − − 1.0 V VR_RDY High − Output Leakage Current VR_RDY = 5.5 V via 1 K − − 0.1 mA VR_RDY Upper Threshold Voltage (INTEL) VCore Increasing, DAC = 1.3 V − 300 250 mV (below DAC) VR_RDY Lower Threshold Voltage (INTEL) VCore Decreasing, DAC = 1.3 V 390 350 300 mV (below DAC) VR_RDY Upper Threshold Voltage (AMD) VCore Increasing, DAC = 1.3 V − − 142 mV (below DAC) VR_RDY Lower Threshold Voltage (AMD) VCore Decreasing, DAC = 1.3 V 282 − 192 mV (below DAC) http://onsemi.com 10 NCP5395T ELECTRICAL CHARACTERISTICS 0°C < TA < 70°C; 0°C < TJ < 125°C; 4.75 < VCC < 5.25 V; All DAC Codes; CVCC = 0.1 mF unless otherwise noted. Parameter Test Conditions Min Typ Max Unit VR_RDY (Power Good) OUTPUT VR_RDY Rising Delay VCore Increasing − 250 − ms VR_RDY Falling Delay VCore Decreasing − 5.0 − ms 3.0 − − V PWM G4 OUTPUT Output High Voltage Sourcing 500 mA Mid Output Voltage 1.4 1.5 1.6 V Output Low Voltage Sinking 500 mA − − 0.7 V Delay + Rise Time (Note 3) CL (PCB) = 50 pF, DVo = VCC to GND − 10 − ns Delay + Fall Time (Note 3) CL (PCB) = 50 pF, DVo = GND to VCC − 10 − ns Tri−State Output Leakage (Note 3) Gx = 2.5 V, x = 1−4 − − 1.5 mA Output Impedance − HI or LO State Max Resistance to VCC (HI) or GND (LO) − 75 150 W − − 2.0 V Minimum VCC for Valid PWM Output Level PWM 4 2/3/4 Phase Detection 2 Phase Mode Note Gate 4 tied to VCC 3.2 − VCC V 4 Phase Mode Note Gate Driver will pull to 1.5 V 1.2 − 2.8 V 3 Phase Mode Note Gate 4 tied to GND 0 − 0.8 V Soft−Start Ramp Time DAC = 0 to DAC = 1.1 V 1.0 − 1.3 ms VR11 Vboot time Not used in Legacy Startup 400 500 600 ms VID Threshold 450 600 770 mV VR11 Input Bias Current −100 − 100 nA 200 − 300 ns − − 4.8 V 3.33 − − V DIGITAL SOFT−START VID7/VR11/AMD/LEGACY INPUT Delay Before Latching VID Change (VID Deskewing) (Note 3) Measured from the Edge of the 1st VID Change AMD Upper Threshold Note: When above this threshold the controller will ramp directly to VID without stopping at Vboot AMD Lower Threshold http://onsemi.com 11 NCP5395T ELECTRICAL CHARACTERISTICS 0°C < TA < 70°C; 0°C < TJ < 125°C; 4.75 < VCC < 5.25 V; All DAC Codes; CVCC = 0.1 mF unless otherwise noted. Parameter Test Conditions Min Typ Max Unit ENABLE INPUT Enable High Input Leakage Current Pull−up to 1.3 V VR11.1 Threshold AMD Upper Threshold AMD Lower Threshold − − 200 nA 450 600 770 mV − 1.3 1.5 V 0.9 1.1 − V AMD Total Hysteresis Rising− Falling Threshold − 200 − mV Enable Delay Time Measure time from Enable transitioning HI to when SS begins − 3.5 − ms 0.97 1.00 1.03 V/V CURRENT LIMIT ILIM to VDRP Gain ILIM to VRDP Gain in PSI 4 Phase − 0.25 − V/V ILIM to VDRP Gain in PSI 3 Phase − 0.333 − V/V ILIM to VDRP Gain in PSI 2 Phase − 0.5 − V/V ILIM Pin Input Bias Current − 0.1 1.0 mA 0.1 − 2.0 V −25 − 25 mV − − 120 ns VR11 Over Voltage Threshold DAC+ 160 DAC+ 190 DAC+ 210 mV AMD Over Voltage Threshold DAC+ 210 DAC+ 235 DAC+ 260 mV − − 100 ns VCC UVLO Start Threshold 4.0 4.25 4.5 V VCC UVLO Stop Threshold 3.8 4.05 4.3 V VCC UVLO Hysteresis 150 200 − mV ILIM Pin Working Voltage Range ILIM accuracy Measured with respect to the ILIM setting Delay OVERVOLTAGE PROTECTION Delay UNDERVOLTAGE PROTECTION 12VMON UVLO 12VMON (High Threshold) VCC Valid − 0.6 0.8 v 12VMON (Low Threshold) VCC Valid 0.4 0.5 − v DAC OUTPUT Output Source Current Vout = 1.6 V 0 − 5.0 mA Output Sink Current Vout = 0.3 V 5.0 − 16 mA Threshold 450 600 770 mV VR11 Mode Leakage −100 − 100 nA 10 − 25 mA 200 − 300 ns VID INPUTS AMD Mode Input Bias Current Delay before Latching VID Change (VID Deskewing) (Note 3) Measured from the edge of the VID change http://onsemi.com 12 1st NCP5395T ELECTRICAL CHARACTERISTICS 0°C < TA < 70°C; 0°C < TJ < 125°C; 4.75 < VCC < 5.25 V; All DAC Codes; CVCC = 0.1 mF unless otherwise noted. Parameter Test Conditions Min Typ Max Unit Slew Rate Limit (Intel Mode) 12.5 Slew Rate Limit (AMD Mode) 3.125 − 15 mV/ms − 3.75 mV/ms − 0.84 − mV/ms 20 − 42 mA VCCP UVLO Start Threshold 8.2 9.0 9.5 V VCCP UVLO Stop Threshold 7.2 8.0 8.5 V VCCP UVLO Hysteresis 1.0 − − V 3.0 3.17 − DIGITAL DAC SLEW RATE LIMITER Soft−Start Slew Rate INPUT SUPPLY CURRENT VCC Operating Current EN Low, No PWM VCCP SUPPLY VOLTAGE VCCP POR Voltage at which the Driver OVP becomes active BOOST PIN UVLO BOOST VCC UVLO Start Threshold 3.45 BOOST VCC UVLO Stop Threshold 3.3 3.85 V BOOST VCC UVLO Hysteresis 50 200 − mV 4.15 V BOOST SUPPLY CURRENT IVCCP_NORM Standby Current EN = VCC, VCCP = 12 V − − 2.5 mA IBST1_SD Standby Current IN = VCCP, VCCP = 12 V − 0.25 2.5 mA IBST2_SD Standby Current IN = GND, VCCP = 12 V − 0.25 2.5 mA IBST3_SD Standby Current IN = GND, VCCP = 12 V − 0.25 2.5 mA 1.7 − 2.03 V STARTUP HIGH SIDE SHORT TRIP (Active only during Vswx Output Overvoltage Trip Threshold at Startup 1st power on) Power Startup time, VCC > 9 V http://onsemi.com 13 NCP5395T ELECTRICAL CHARACTERISTICS 0°C < TA < 70°C; 0°C < TJ < 125°C; 4.75 < VCC < 5.25 V; All DAC Codes; CVCC = 0.1 mF unless otherwise noted. Parameter Test Conditions Min Typ Max Unit W HIGH SIDE DRIVER RH_TG Output Resistance, Sourcing VBST − VSW = 12 V − 1.8 5.0 RH_TG Output Resistance, Sinking VBST − VSW = 12 V − 1.0 2.5 TrDRVH Transition Time CLOAD = 3 nF, VBST − VSW = 12 V − 25 − ns TfDRVH Transition Time CLOAD = 3 nF, VBST − VSW = 12 V − 20 − ns TpdhDRVH Propagation Delay (Note 4) Driving High, CLOAD = 3 nF, VCCP = 12 V − 15 − ns RH_BG Output Resistance, Sourcing SW = GND − 1.6 5.0 W RL_BG Output Resistance, Sinking SW = VCC − 1.0 2.5 W TrDRVL Transition Time CLOAD = 3 nF − 20 − ns TfDRVL Transition Time CLOAD = 3 nF − 20 − ns TpdhDRVL Propagation Delay (Note 4) Driving High, CLOAD = 3 nF, VCCP = 12 V − 15 − ns − −1.0 − mV 150 170 − °C − 20 − °C − − − − − − ±0.5 ±5.0 ±8.0 % mV mV LOW SIDE DRIVER VNCDT Negative Current Detector Threshold (Note 3) THERMAL SHUTDOWN Tsd Thermal Shutdown (Note 3) Tsdhys Thermal Shutdown Hysteresis (Note 3) VRM 11 DAC System Voltage Accuracy 1.0 V < DAC < 1.6 V 0.8 V < DAC < 1.0 V 0.5 V < DAC < 0.8 V 4. For propagation delays, “tpdh” refers to the specified signal going high “tpdl” refers to it going low. Reference Gate Timing Diagram. IN tpdlDRVL tfDRVL DRVL 90% 90% 2V 10% 10% tpdhDRVH thDRVH tpdlDRVH 90% 10% tfDRVH 90% 2V DRVH−SW trDRVL 10% tpdhDRVL SW Figure 5. Timing Diagram http://onsemi.com 14 NCP5395T Table 2. VRM11 VID CODES VID7 800 mV VID6 400 mV VID5 200 mV VID4 100 mV VID3 50 mV VID2 25 mV VID1 12.5 mV VID0 6.25 mV 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 1.60000 02 0 0 0 0 0 0 1 1 1.59375 03 0 0 0 0 0 1 0 0 1.58750 04 0 0 0 0 0 1 0 1 1.58125 05 0 0 0 0 0 1 1 0 1.57500 06 0 0 0 0 0 1 1 1 1.56875 07 0 0 0 0 1 0 0 0 1.56250 08 0 0 0 0 1 0 0 1 1.55625 09 0 0 0 0 1 0 1 0 1.55000 0A 0 0 0 0 1 0 1 1 1.54375 0B 0 0 0 0 1 1 0 0 1.53750 0C 0 0 0 0 1 1 0 1 1.53125 0D 0 0 0 0 1 1 1 0 1.52500 0E 0 0 0 0 1 1 1 1 1.51875 0F 0 0 0 1 0 0 0 0 1.51250 10 0 0 0 1 0 0 0 1 1.50625 11 0 0 0 1 0 0 1 0 1.50000 12 0 0 0 1 0 0 1 1 1.49375 13 0 0 0 1 0 1 0 0 1.48750 14 0 0 0 1 0 1 0 1 1.48125 15 0 0 0 1 0 1 1 0 1.47500 16 0 0 0 1 0 1 1 1 1.46875 17 0 0 0 1 1 0 0 0 1.46250 18 0 0 0 1 1 0 0 1 1.45625 19 0 0 0 1 1 0 1 0 1.45000 1A 0 0 0 1 1 0 1 1 1.44375 1B 0 0 0 1 1 1 0 0 1.43750 1C 0 0 0 1 1 1 0 1 1.43125 1D 0 0 0 1 1 1 1 0 1.42500 1E 0 0 0 1 1 1 1 1 1.41875 1F 0 0 1 0 0 0 0 0 1.41250 20 0 0 1 0 0 0 0 1 1.40625 21 0 0 1 0 0 0 1 0 1.40000 22 0 0 1 0 0 0 1 1 1.39375 23 0 0 1 0 0 1 0 0 1.38750 24 0 0 1 0 0 1 0 1 1.38125 25 0 0 1 0 0 1 1 0 1.37500 26 0 0 1 0 0 1 1 1 1.36875 27 0 0 1 0 1 0 0 0 1.36250 28 0 0 1 0 1 0 0 1 1.35625 29 0 0 1 0 1 0 1 0 1.35000 2A 0 0 1 0 1 0 1 1 1.34375 2B 0 0 1 0 1 1 0 0 1.33750 2C 0 0 1 0 1 1 0 1 1.33125 2D http://onsemi.com 15 Voltage (V) HEX 00 01 NCP5395T Table 2. VRM11 VID CODES VID7 800 mV VID6 400 mV VID5 200 mV VID4 100 mV VID3 50 mV VID2 25 mV VID1 12.5 mV VID0 6.25 mV Voltage (V) HEX 0 0 1 0 1 1 1 0 1.32500 2E 0 0 1 0 1 1 1 1 1.31875 2F 0 0 1 1 0 0 0 0 1.31250 30 0 0 1 1 0 0 0 1 1.30625 31 0 0 1 1 0 0 1 0 1.30000 32 0 0 1 1 0 0 1 1 1.29375 33 0 0 1 1 0 1 0 0 1.28750 34 0 0 1 1 0 1 0 1 1.28125 35 0 0 1 1 0 1 1 0 1.27500 36 0 0 1 1 0 1 1 1 1.26875 37 0 0 1 1 1 0 0 0 1.26250 38 0 0 1 1 1 0 0 1 1.25625 39 0 0 1 1 1 0 1 0 1.25000 3A 0 0 1 1 1 0 1 1 1.24375 3B 0 0 1 1 1 1 0 0 1.23750 3C 0 0 1 1 1 1 0 1 1.23125 3D 0 0 1 1 1 1 1 0 1.22500 3E 0 0 1 1 1 1 1 1 1.21875 3F 0 1 0 0 0 0 0 0 1.21250 40 0 1 0 0 0 0 0 1 1.20625 41 0 1 0 0 0 0 1 0 1.20000 42 0 1 0 0 0 0 1 1 1.19375 43 0 1 0 0 0 1 0 0 1.18750 44 0 1 0 0 0 1 0 1 1.18125 45 0 1 0 0 0 1 1 0 1.17500 46 0 1 0 0 0 1 1 1 1.16875 47 0 1 0 0 1 0 0 0 1.16250 48 0 1 0 0 1 0 0 1 1.15625 49 0 1 0 0 1 0 1 0 1.15000 4A 0 1 0 0 1 0 1 1 1.14375 4B 0 1 0 0 1 1 0 0 1.13750 4C 0 1 0 0 1 1 0 1 1.13125 4D 0 1 0 0 1 1 1 0 1.12500 4E 0 1 0 0 1 1 1 1 1.11875 4F 0 1 0 1 0 0 0 0 1.11250 50 0 1 0 1 0 0 0 1 1.10625 51 0 1 0 1 0 0 1 0 1.10000 52 0 1 0 1 0 0 1 1 1.09375 53 0 1 0 1 0 1 0 0 1.08750 54 0 1 0 1 0 1 0 1 1.08125 55 0 1 0 1 0 1 1 0 1.07500 56 0 1 0 1 0 1 1 1 1.06875 57 0 1 0 1 1 0 0 0 1.06250 58 0 1 0 1 1 0 0 1 1.05625 59 0 1 0 1 1 0 1 0 1.05000 5A 0 1 0 1 1 0 1 1 1.04375 5B http://onsemi.com 16 NCP5395T Table 2. VRM11 VID CODES VID7 800 mV VID6 400 mV VID5 200 mV VID4 100 mV VID3 50 mV VID2 25 mV VID1 12.5 mV VID0 6.25 mV Voltage (V) HEX 0 1 0 1 1 1 0 0 1.03750 5C 0 1 0 1 1 1 0 1 1.03125 5D 0 1 0 1 1 1 1 0 1.02500 5E 0 1 0 1 1 1 1 1 1.01875 5F 0 1 1 0 0 0 0 0 1.01250 60 0 1 1 0 0 0 0 1 1.00625 61 0 1 1 0 0 0 1 0 1.00000 62 0 1 1 0 0 0 1 1 0.99375 63 0 1 1 0 0 1 0 0 0.98750 64 0 1 1 0 0 1 0 1 0.98125 65 0 1 1 0 0 1 1 0 0.97500 66 0 1 1 0 0 1 1 1 0.96875 67 0 1 1 0 1 0 0 0 0.96250 68 0 1 1 0 1 0 0 1 0.95625 69 0 1 1 0 1 0 1 0 0.95000 6A 0 1 1 0 1 0 1 1 0.94375 6B 0 1 1 0 1 1 0 0 0.93750 6C 0 1 1 0 1 1 0 1 0.93125 6D 0 1 1 0 1 1 1 0 0.92500 6E 0 1 1 0 1 1 1 1 0.91875 6F 0 1 1 1 0 0 0 0 0.91250 70 0 1 1 1 0 0 0 1 0.90625 71 0 1 1 1 0 0 1 0 0.90000 72 0 1 1 1 0 0 1 1 0.89375 73 0 1 1 1 0 1 0 0 0.88750 74 0 1 1 1 0 1 0 1 0.88125 75 0 1 1 1 0 1 1 0 0.87500 76 0 1 1 1 0 1 1 1 0.86875 77 0 1 1 1 1 0 0 0 0.86250 78 0 1 1 1 1 0 0 1 0.85625 79 0 1 1 1 1 0 1 0 0.85000 7A 0 1 1 1 1 0 1 1 0.84375 7B 0 1 1 1 1 1 0 0 0.83750 7C 0 1 1 1 1 1 0 1 0.83125 7D 0 1 1 1 1 1 1 0 0.82500 7E 0 1 1 1 1 1 1 1 0.81875 7F 1 0 0 0 0 0 0 0 0.81250 80 1 0 0 0 0 0 0 1 0.80625 81 1 0 0 0 0 0 1 0 0.80000 82 1 0 0 0 0 0 1 1 0.79375 83 1 0 0 0 0 1 0 0 0.78750 84 1 0 0 0 0 1 0 1 0.78125 85 1 0 0 0 0 1 1 0 0.77500 86 1 0 0 0 0 1 1 1 0.76875 87 1 0 0 0 1 0 0 0 0.76250 88 1 0 0 0 1 0 0 1 0.75625 89 http://onsemi.com 17 NCP5395T Table 2. VRM11 VID CODES VID7 800 mV VID6 400 mV VID5 200 mV VID4 100 mV VID3 50 mV VID2 25 mV VID1 12.5 mV VID0 6.25 mV Voltage (V) HEX 1 0 0 0 1 0 1 0 0.75000 8A 1 0 0 0 1 0 1 1 0.74375 8B 1 0 0 0 1 1 0 0 0.73750 8C 1 0 0 0 1 1 0 1 0.73125 8D 1 0 0 0 1 1 1 0 0.72500 8E 1 0 0 0 1 1 1 1 0.71875 8F 1 0 0 1 0 0 0 0 0.71250 90 1 0 0 1 0 0 0 1 0.70625 91 1 0 0 1 0 0 1 0 0.70000 92 1 0 0 1 0 0 1 1 0.69375 93 1 0 0 1 0 1 0 0 0.68750 94 1 0 0 1 0 1 0 1 0.68125 95 1 0 0 1 0 1 1 0 0.67500 96 1 0 0 1 0 1 1 1 0.66875 97 1 0 0 1 1 0 0 0 0.66250 98 1 0 0 1 1 0 0 1 0.65625 99 1 0 0 1 1 0 1 0 0.65000 9A 1 0 0 1 1 0 1 1 0.64375 9B 1 0 0 1 1 1 0 0 0.63750 9C 1 0 0 1 1 1 0 1 0.63125 9D 1 0 0 1 1 1 1 0 0.62500 9E 1 0 0 1 1 1 1 1 0.61875 9F 1 0 1 0 0 0 0 0 0.61250 A0 1 0 1 0 0 0 0 1 0.60625 A1 1 0 1 0 0 0 1 0 0.60000 A2 1 0 1 0 0 0 1 1 0.59375 A3 1 0 1 0 0 1 0 0 0.58750 A4 1 0 1 0 0 1 0 1 0.58125 A5 1 0 1 0 0 1 1 0 0.57500 A6 1 0 1 0 0 1 1 1 0.56875 A7 1 0 1 0 1 0 0 0 0.56250 A8 1 0 1 0 1 0 0 1 0.55625 A9 1 0 1 0 1 0 1 0 0.55000 AA 1 0 1 0 1 0 1 1 0.54375 AB 1 0 1 0 1 1 0 0 0.53750 AC 1 0 1 0 1 1 0 1 0.53125 AD 1 0 1 0 1 1 1 0 0.52500 AE 1 0 1 0 1 1 1 1 0.51875 AF 1 0 1 1 0 0 0 0 0.51250 B0 1 0 1 1 0 0 0 1 0.50625 B1 1 0 1 1 0 0 1 0 0.50000 B2 1 1 1 1 1 1 1 0 OFF FE 1 1 1 1 1 1 1 1 OFF FF http://onsemi.com 18 NCP5395T Test Condition Parameter MIN TYP MAX Units − − − − − − ±0.5 ±1.0 −2.0, +3.0 % % % AMD DAC 1.0 V < DAC < 1.55V 0.6 V ≤ DAC < 1.0V 0.375 V < DAC < 0.6V System Voltage Accuracy 5. NOTE: Internal DAC voltage is centered 19 mV below the listed voltage for VR11.1. No DAC offset is implemented for AMD operation. DAC should be equal to the Nominal Vout shown in the table. Table 3. AMD PROCESSOR 6−BIT VID CODE (VID) Codes VID5 VID4 VID3 VID2 VID1 VID0 Nominal Vout Units 0 0 0 0 0 0 1.550 V 0 0 0 0 0 1 1.525 V 0 0 0 0 1 0 1.500 V 0 0 0 0 1 1 1.475 V 0 0 0 1 0 0 1.450 V 0 0 0 1 0 1 1.425 V 0 0 0 1 1 0 1.400 V 0 0 0 1 1 1 1.375 V 0 0 1 0 0 0 1.350 V 0 0 1 0 0 1 1.325 V 0 0 1 0 1 0 1.300 V 0 0 1 0 1 1 1.275 V 0 0 1 1 0 0 1.250 V 0 0 1 1 0 1 1.225 V 0 0 1 1 1 0 1.200 V 0 0 1 1 1 1 1.175 V 0 1 0 0 0 0 1.150 V 0 1 0 0 0 1 1.125 V 0 1 0 0 1 0 1.100 V 0 1 0 0 1 1 1.075 V 0 1 0 1 0 0 1.050 V 0 1 0 1 0 1 1.025 V 0 1 0 1 1 0 1.000 V 0 1 0 1 1 1 0.975 V 0 1 1 0 0 0 0.950 V 0 1 1 0 0 1 0.925 V 0 1 1 0 1 0 0.900 V 0 1 1 0 1 1 0.875 V 0 1 1 1 0 0 0.850 V 0 1 1 1 0 1 0.825 V 0 1 1 1 1 0 0.800 V 0 1 1 1 1 1 0.775 V 1 0 0 0 0 0 0.7625 V 1 0 0 0 0 1 0.7500 V http://onsemi.com 19 NCP5395T Table 3. AMD PROCESSOR 6−BIT VID CODE (VID) Codes VID5 VID4 VID3 VID2 VID1 VID0 Nominal Vout Units 1 0 0 0 1 0 0.7375 V 1 0 0 0 1 1 0.7250 V 1 0 0 1 0 0 0.7125 V 1 0 0 1 0 1 0.7000 V 1 0 0 1 1 0 0.6875 V 1 0 0 1 1 1 0.6750 V 1 0 1 0 0 0 0.6625 V 1 0 1 0 0 1 0.6500 V 1 0 1 0 1 0 0.6375 V 1 0 1 0 1 1 0.6250 V 1 0 1 1 0 0 0.6125 V 1 0 1 1 0 1 0.6000 V 1 0 1 1 1 0 0.5875 V 1 0 1 1 1 1 0.5750 V 1 1 0 0 0 0 0.5625 V 1 1 0 0 0 1 0.5500 V 1 1 0 0 1 0 0.5375 V 1 1 0 0 1 1 0.5250 V 1 1 0 1 0 0 0.5125 V 1 1 0 1 0 1 0.5000 V 1 1 0 1 1 0 0.4875 V 1 1 0 1 1 1 0.4750 V 1 1 1 0 0 0 0.4625 V 1 1 1 0 0 1 0.4500 V 1 1 1 0 1 0 0.4375 V 1 1 1 0 1 1 0.4250 V 1 1 1 1 0 0 0.4125 V 1 1 1 1 0 1 0.4000 V 1 1 1 1 1 0 0.3875 V 1 1 1 1 1 1 0.3750 V http://onsemi.com 20 NCP5395T FUNCTIONAL DESCRIPTIONS General sums the remote output voltage with a 1.3 V reference. The resulting voltage at the output of the remote sense amplifier is: The NCP5395T dual edge modulated multiphase PWM controller is specifically designed with the necessary features for a high current CPU system. The IC consists of the following blocks: Precision Flexible DAC, Differential Remote Voltage Sense Amplifier, High Performance Voltage Error Amplifier, Differential Current Feedback Amplifiers, Precision Oscillator and Saw−tooth Generator, and PWM Comparators with Hysteresis. The controller also supports power saving mode as per Intel VR11.1 by accurately monitoring the current and switching between multi−phase and single phase operations as requested by the microprocessor system. Protection features include: Undervoltage Lockout, Soft−Start, Overcurrent Protection, Overvoltage Protection, and Power Good Monitor. V Diffout + V out ) 1.3 V * V dac * V outreturn This signal then goes through a standard compensation circuit and into the inverting input of the error amplifier. The non−inverting input of the error amplifier is also connected to the 1.3 V reference. The 1.3 V reference then is subtracted out and the error signal at the comp pin of the error amplifier is as normally expected: V comp + V dac * V out The non−inverting input of the remote sense amplifier is pulled low through a small current sink during a fault condition to prevent accidental charging of the regulator output. 2/3/4 Phase Operation Precision Programmable DAC The part can be configured to 2−, 3−, or 4−phase mode. In 2− or 3−phase mode, the internal drivers will be used. In 4−phase mode, an external driver must be used to drive phase 4. The NCP5359 driver is suggested to be used with the controller. The input to G4 pin will decide which phase mode the system is in operation. Please refer to the Application Schematics for more information. A precision flexible DAC is provided. The DAC will conform to 2 different specifications: AMD or VR11.1. The VID7/AMD pin is provided to determine which DAC specification will be used and which soft−start mode the part will use for power up. There are two soft−start modes. If VID7/AMD is above it’s threshold the device will soft−start and ramp directly to the DAC code present on the VID inputs. The following truth table describes the functionality: VID7/AMD Pin VID7 Enable Pin Mode Soft−Start Mode Above AMD Threshold Not active AMD Thresholds Ramp to VID Below AMD Threshold Active VR11.1 Thresholds Ramp to Vboot High Performance Voltage Error Amplifier A high performance voltage error amplifier is provided. The error amplifier’s inverting input is VFB and its output is COMP. A standard type 3 compensation circuit is used compensate the system. This involves a 3 pole, 2 zero compensation network. The comp pin is pulled to ground before soft−start for smooth start up. Differential Current Sense Four differential amplifiers are provided to sense the output current of each phase. These current sense amplifiers sense the current through the corresponding phase. A voltage is generated across a current sense element such as an inductor or sense resistor. The sense element should be between 0.3 mW and 1.5 mW. It is possible to sense both negative and positive going current. The information is used to create the signal CSSUM and provide feedback for current sharing. VID Inputs VID0−VID7 control the target regulation voltage during normal operation. In AMD mode the VID capture is enabled just before soft−start. In VR11 mode the VID capture is enabled at the end of the VBOOT waiting period. If the VID is valid the DAC will track to it. If an invalid VID occurs it will be ignored for 10 ms before the controller shuts down. Remote Sense Amplifier A high performance differential amplifier is provided to accurately sense the output voltage of the regulator. The non−inverting input should be connected to the regulator’s output voltage. The inverting input should be connected to the return line of the regulator. Both connection points are intended to be at a remote point so that the most accurate reading of the output voltage can be obtained. The amplifier is configured in a very unique way. First, the gain of the amplifier is internally set to unity. Second, both the inverting and non−inverting inputs of the amplifier are summing nodes. The inverting input sums the output voltage return voltage with the DAC voltage. The non−inverting input Precision Oscillator A programmable precision oscillator is provided. This oscillator is programmed by the summed resistance of an oscillator resistor and a current limit resistor. The output voltage of this pin is 2V used as the reference for the current limit. The oscillator frequency range is 125 KHz/phase to 1000 KHz/phase. The oscillator frequency is proportional to the current drawn out of the OSC pin. Connecting a resistor (Rosc) from OSC pin to the ground will set the target oscillator frequency. The relation between the Rosc and Fsw can be described as below: http://onsemi.com 21 NCP5395T Over Voltage Protection Rosc = 15530 x Fsw^(-1.111) The output voltage is monitored at the input of the differential amplifier. During normal operation, if the output voltage exceeds the DAC voltage by 185 mV, or 285 mV if in AMD mode, the VR_RDY flag will transition low the high side gate drivers set to low, and the low side gate drivers are all brought to high until the voltage falls below the OVP threshold. If the over voltage trip 8 times the output voltage will shut down. The OVP will not shut down the controller if it occurs during soft−start. This is to allow the controller to pull the output down to the DAC voltage and start up into a pre−charged output. PWM Comparators Four PWM comparators are incorporated within the IC. The non−inverting input of the comparators is connected to the output of the error amplifier. The inverting input is connected to a summed output of the phase current and the oscillator ramp voltage with an offset. The output of the comparator generates the PWM control signals. During steady state operation, the duty cycle will center on the valley of the saw−tooth waveform. During a transient event, the controller will operate somewhat hysteretic, with the duty cycle climbing along either the down ramp, up ramp, or both. VCCP Power ON Reset OVP Soft−start is implemented internally. A digital counter steps the DAC up from zero to the target voltage based on the predetermined rate in the spec table. There are 2 possible soft start modes: VR11 and AMD. AMD mode simply ramps Vcore from 0 V directly to the DAC setting. The VR11 mode ramps DAC to 1.1 V, pauses for 500 ms, reads the DAC setting, then ramps to the final DAC setting. The VCCP power on reset OVP feature is used to protect the CPU during start up. When VCCP is higher than 3.2 V, the gate driver will monitor the switching node SW pin. If SWNx pin higher than 1.9 V, the bottom gate will be forced to high for discharge of the output capacitor. This works best if the 5 volt standby is diode OR’ed into VCCP with the 12 V rail. The fault mode will be latched and the DRVON pin will be forced to low, unless VCCP is reduced below the UVLO threshold. Digital Slew Rate Limiter / Soft−Start Block Power Saving Mode Soft−Start The controller is designed to allow power saving operation to maintain a maximum efficiency. When a low PSI signal from microcontroller is received, the controller will keep one phase operating while shedding other phases. The active one phase will operate in diode emulation mode, minimizing power losses in light load. The device also maintains an RPM operation in power saving mode. The 12VMON input will be used for two purposes: feedforward input supply information for RPM mode and secondary power input voltage UVLO. When the low PSI signal is de−asserted, the dropped phases will be pulled back in to be ready for heavy load and the device will be back to regular PWM mode. The slew rate limiter and the soft−start block are to be implemented with a digital up/down counter controlled by an oscillator that is synchronized to VID line changes. During soft−start the DAC will ramp at the soft−start rate, after soft start is complete the ramp rate will follow either the Intel or the AMD slew rate depending on the mode. Under Voltage Lockouts An under voltage circuit senses the VCC input of the controller and the VCCP input of the driver. During power up the input voltage to the controller is monitored. The PWM outputs and the soft start circuit are disabled until the input voltage exceeds the threshold voltage of the comparators. Hysteresis is incorporated within the comparators. The DRVON is held low until VCCP reaches the start threshold during startup. If VCCP decreases below the stop threshold, the output gate will be forced low unit input voltage VCCP rises above the startup threshold. Adaptive Non−overlap The non−overlap dead time control is used to avoid shoot through damage to the power MOSFETs. When the PWM signal pull high, DRVL will go low after a propagation delay, the controller monitors the switching node (SWN) pin voltage and the gate voltage of the MOSFET to know the status of the MOSFET. When the low side MOSFET status is off an internal timer will delay turn on of the high–side MOSFET. When the PWM pull low, gate DRVH will go low after the propagation delay (tpdDRVH). The time to turn off the high side MOSFET is depending on the total gate charge of the high−side MOSFET. A timer will be triggered once the high side MOSFET is turn off to delay the turn on the low−side MOSFET. Over Current Latch A programmable over current latch is incorporated within the IC. The oscillator pin provides the reference voltage for this pin. A resistor divider from the OSC pin generates the ILIM voltage. The latch is set when the current information on Vdroop exceeds the programmed voltage plus a 1.3 V offset. DRVON is immediately set low. To recover the part must be reset by the EN pin or by cycling VCC. UVLO Monitor Layout Guidelines If the output voltage falls greater than 300 mV below the DAC voltage for more than 5 ms the UVLO comparator will trip sending the VR_RDY signal low. Layout is very important thing for design a DC−DC converter. Bootstrap capacitor and Vin capacitor are most http://onsemi.com 22 NCP5395T critical items, it should be placed as close as to the controller IC. Another item is using a GND plane. Ground plane can provide a good return path for gate drives for reducing the ground noise. Therefore GND pin should be directly connected to the ground plane and close to the low−side MOSFET source pin. Also, the gate drive trace should be considered. The gate drives has a high di/dt when switching, therefore a minimized gate drives trace can reduce the di/dv, raise and fall time for reduce the switching loss. 1.25 V ENABLE VID Captured 1.25 V VID Not Valid VID Valid 1 ms − 20 ms Rise Time 5V 12 V 12 V 1 ms − 20 ms Rise Time 5 and 12 Good DRVON VR11 Soft−start Mode Latched 3.5 ms Calibration Time Soft−start Slew Rate DAC Setting 1.10 V Soft−start Slew Rate 500 ms VOUT/DAC 500 ms VR_RDY Figure 6. VR11.1 Start Up Timing Diagram http://onsemi.com 23 NCP5395T ENABLE 5V VID7/AMD 1 ms − 20 ms Rise Time VCC 5V 1 ms − 20 ms Rise Time 12 V 9.5 V VCCP VCC and VCCP UVLO AMD/Legacy Soft Start Mode Latched 3.5 ms Calibration Time DRVON DAC Setting SS Slew Rate VOUT/DAC 500 ms VR_RDY Figure 7. AMD / Legacy Start Up Timing Diagram http://onsemi.com 24 NCP5395T PACKAGE DIMENSIONS QFN48, 7x7, 0.5P CASE 485AJ−01 ISSUE O ÈÈ ÈÈ ÈÈ PIN 1 LOCATION D NOTES: 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO THE PLATED TERMINAL AND IS MEASURED ABETWEEN 0.15 AND 0.30 MM FROM TERMINAL TIP. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. A B E DIM A A1 A3 b D D2 E E2 e K L L 2X 0.15 C DETAIL A OPTIONAL CONSTRUCTION 2X SCALE 2X 0.15 C TOP VIEW (A3) 0.05 C MILLIMETERS MIN MAX 0.80 1.00 0.00 0.05 0.20 REF 0.20 0.30 7.00 BSC 5.00 5.20 7.00 BSC 5.00 5.20 0.50 BSC 0.20 −−− 0.30 0.50 A 0.08 C SOLDERING FOOTPRINT* A1 NOTE 4 C SIDE VIEW D2 DETAIL A 2X SEATING PLANE 5.20 1 K 13 25 12 2X 7.30 48X 0.63 E2 1 48 48X L 48X 36 37 e e/2 48X BOTTOM VIEW 0.30 b 0.10 C A B 0.05 C NOTE 3 0.50 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 http://onsemi.com 25 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCP5395T/D