TI LM25005MHX/NOPB Lm25005 42v, 2.5a step-down switching regulator Datasheet

LM25005
www.ti.com
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
LM25005 42V, 2.5A Step-Down Switching Regulator
Check for Samples: LM25005
FEATURES
DESCRIPTION
•
•
•
•
•
•
The LM25005 switching regulator features all of the
functions necessary to implement an efficient, high
voltage buck regulator using a minimum of external
components. This easy to use regulator includes a
42V, 160mΩ, N-channel MOSFET, with an output
current capability of 2.5 Amps. The regulator control
method is based upon current mode control utilizing
an emulated current ramp. Current mode control
provides inherent line voltage feed-forward, cycle-bycycle current limiting and ease of loop compensation.
The use of an emulated control ramp reduces noise
sensitivity of the pulse-width modulation circuit,
allowing reliable control of very small duty cycles
necessary in high input voltage applications. The
operating frequency is programmable from 50kHz to
500kHz. An oscillator synchronization pin allows
multiple LM25005 regulators to self-synchronize or to
be synchronized to an external clock. Additional
protection features include: current limit, thermal
shutdown and remote shutdown capability. The
device is available in a power enhanced HTSSOP
package featuring an exposed die attach pad to aid
thermal dissipation.
1
2
•
•
•
•
•
•
Integrated 42V, 160mΩ N-Channel MOSFET
Ultra-Wide Input Voltage Range from 7V to 42V
Internal Bias Regulator
Adjustable Output Voltage from 1.225V
1.5% Feedback Reference Accuracy
Current Mode Control with Emulated Inductor
Current Ramp
Single Resistor Oscillator Frequency Setting
Oscillator Synchronization Input
Programmable Soft-Start
Shutdown / Standby Input
Wide Bandwidth Error Amplifier
Thermal Shutdown
Package
•
HTSSOP (Exposed Pad)
Simplified Application Schematic
VIN
LM25005
BST
VIN
SD
VOUT
SW
SYNC
COMP
IS
GND
OUT
FB
RAMP RT SS VCC
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2013, Texas Instruments Incorporated
LM25005
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
www.ti.com
Connection Diagram
1
VCC
BST
SD
PRE
VIN
SW
VIN
SW
2
3
4
5
6
7
8
9
10
SYNC
IS
COMP
IS
FB
PGND
RT
PGND
RAMP
OUT
AGND
SS
20
19
18
17
16
15
14
13
12
11
Figure 1. Top View
20-Lead HTSSOP
PIN DESCRIPTIONS
Pin(S)
1
2
Name
VCC
Description
Application Information
Output of the bias regulator
Vcc tracks Vin up to 9V. Beyond 9V, Vcc is regulated to 7 Volts.
A 0.1uF to 1uF ceramic decoupling capacitor is required. An
external voltage (7.5V – 14V) can be applied to this pin to
reduce internal power dissipation.
2
SD
Shutdown or UVLO input
If the SD pin voltage is below 0.7V the regulator will be in a low
power state. If the SD pin voltage is between 0.7V and 1.225V
the regulator will be in standby mode. If the SD pin voltage is
above 1.225V the regulator will be operational. An external
voltage divider can be used to set a line undervoltage shutdown
threshold. If the SD pin is left open circuit, a 5µA pull-up current
source configures the regulator fully operational.
3, 4
Vin
Input supply voltage
Nominal operating range: 7V to 42V
5
SYNC
Oscillator synchronization input or output
The internal oscillator can be synchronized to an external clock
with an external pull-down device. Multiple LM25005 devices
can be synchronized together by connection of their SYNC pins.
6
COMP
Output of the internal error amplifier
The loop compensation network should be connected between
this pin and the FB pin.
7
FB
Feedback signal from the regulated output
This pin is connected to the inverting input of the internal error
amplifier. The regulation threshold is 1.225V.
8
RT
Internal oscillator frequency set input
The internal oscillator is set with a single resistor, connected
between this pin and the AGND pin. The recommended
frequency range is 50KHz to 500KHz.
9
RAMP
Ramp control signal
An external capacitor connected between this pin and the AGND
pin sets the ramp slope used for current mode control.
Recommended capacitor range 50pF to 2000pF.
10
AGND
Analog ground
Internal reference for the regulator control functions
11
SS
Soft-start
An external capacitor and an internal 10µA current source set
the time constant for the rise of the error amp reference. The SS
pin is held low during standby, Vcc UVLO and thermal
shutdown.
Output voltage connection
Connect directly to the regulated output voltage.
Power ground
Low side reference for the PRE switch and the IS sense resistor.
12
OUT
13, 14
PGND
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
LM25005
www.ti.com
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
PIN DESCRIPTIONS (continued)
Pin(S)
Name
Description
Application Information
15, 16
IS
Current sense
Current measurement connection for the re-circulating diode. An
internal sense resistor and a sample/hold circuit sense the diode
current near the conclusion of the off-time. This current
measurement provides the DC level of the emulated current
ramp.
17, 18
SW
Switching node
The source terminal of the internal buck switch. The SW pin
should be connected to the external Schottky diode and to the
buck inductor.
19
PRE
Pre-charge assist for the bootstrap
capacitor
This open drain output can be connected to SW pin to aid
charging the bootstrap capacitor during very light load conditions
or in applications where the output may be pre-charged before
the LM25005 is enabled. An internal pre-charge MOSFET is
turned on for 250ns each cycle just prior to the on-time interval
of the buck switch.
20
BST
Boost input for bootstrap capacitor
An external capacitor is required between the BST and the SW
pins. A 0.022µF ceramic capacitor is recommended. The
capacitor is charged from Vcc via an internal diode during the
off-time of the buck switch.
NA
EP
Exposed Pad
Exposed metal pad on the underside of the device. It is
recommended to connect this pad to the PWB ground plane, in
order to aid in heat dissipation.
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings (1) (2)
VIN to GND
45V
BST to GND
60V
PRE to GND
45V
SW to GND (Steady State)
-1.5V
BST to VCC
45V
VCC to GND
14V
BST to SW
14V
OUT to GND
Limited to Vin
SD, SYNC, SS, FB to GND
ESD Rating (3)
7V
Human Body Model
Storage Temperature Range
(1)
(2)
(3)
2kV
-65°C to +150°C
Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is intended to be functional. For ensured specifications and test conditions, see the Electrical Characteristics .
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
The human body model is a 100pF capacitor discharged through a 1.5kΩ resistor into each pin.
Operating Ratings (1)
VIN
7V to 42V
−40°C to + 125°C
Operation Junction Temperature
(1)
Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is intended to be functional. For ensured specifications and test conditions, see the Electrical Characteristics .
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
3
LM25005
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
www.ti.com
Electrical Characteristics
Specifications with standard typeface are for TJ = 25°C, and those with boldface type apply over full Operating Junction
Temperature range. VIN = 24V, RT = 32.4kΩ unless otherwise stated. (1)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
6.85
7.15
7.45
V
STARTUP REGULATOR
VccReg
Vcc Regulator Output
Vcc LDO Mode turn-off
Vcc Current Limit
Vcc = 0V
Vcc UVLO Threshold
(Vcc increasing)
9
V
20
mA
VCC SUPPLY
5.95
Vcc Undervoltage Hysteresis
6.35
6.75
V
1
V
Bias Current (Iin)
FB = 1.3V
3
4.5
mA
Shutdown Current (Iin)
SD = 0V
50
85
µA
0.9
V
SHUTDOWN THRESHOLDS
Shutdown Threshold
(SD Increasing)
0.5
0.7
(Standby Increasing)
1.18
1.225
Shutdown Hysteresis
0.1
Standby Threshold
Standby Hysteresis
SD Pull-up Current Source
V
1.27
V
0.1
V
5
µA
SWITCH CHARACTERSICS
Buck Switch Rds(on)
160
BOOST UVLO
3.8
320
mΩ
BOOST UVLO Hysteresis
0.56
V
Pre-charge Switch Rds(on)
75
Ω
Pre-charge Switch on-time
275
ns
V
CURRENT LIMIT
Cycle by Cycle Current Limit
RAMP = 0V
Cycle by Cycle Current Limit Delay
RAMP = 2.5V
3
3.5
4.25
100
A
ns
SOFT-START
SS Current Source
7
10
14
µA
180
200
220
KHz
425
485
525
KHz
OSCILLATOR
Frequency1
Frequency2
RT = 11kΩ
SYNC Source Impedance
10
kΩ
SYNC Sink Impedance
160
Ω
SYNC Threshold (falling)
1.4
Upper SYNC Frequency
V
550
SYNC Pulse Width Minimum
15
KHz
ns
RAMP GENERATOR
Ramp Current 1
Vin = 36V, Vout=10V
136
160
184
µA
Ramp Current 2
Vin = 10V, Vout=10V
18
25
32
µA
PWM COMPARATOR
(1)
4
Forced Off-time
500
ns
Min On-time
80
ns
COMP to PWM Comparator Offset
0.7
V
Min and Max limits are 100% production tested at 25°C. Limits over the operating temperature range are ensured through correlation
using Statistical Quality Control (SQC) methods. Limits are used to calculate Average Outgoing Quality Level (AOQL).
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
LM25005
www.ti.com
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
Electrical Characteristics (continued)
Specifications with standard typeface are for TJ = 25°C, and those with boldface type apply over full Operating Junction
Temperature range. VIN = 24V, RT = 32.4kΩ unless otherwise stated.(1)
Symbol
Parameter
Conditions
Min
Typ
Max
1.207
1.225
1.243
Units
ERROR AMPLIFIER
Feedback Voltage
Vfb = COMP
FB Bias Current
V
10
DC Gain
nA
70
COMP Sink / Source Current
dB
3
Unity Gain Bandwidth
mA
3
MHz
Thermal Shutdown Threshold
165
°C
Thermal Shutdown Hysteresis
25
°C
THERMAL SHUTDOWN
Tsd
THERMAL RESISTANCE
θJC
Junction to Case
4
°C/W
θJA
Junction to Ambient
40
°C/W
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
5
LM25005
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics
Oscillator Frequency vs
Temperature FOSC = 200kHz
Oscillator Frequency vs RT
NORMALIZED OSCILLATOR FREQUENCY
OSCILLATOR FREQUENCY (kHz)
1000
100
10
1
10
100
1000
1.010
1.005
1.000
0.995
0.990
-50
-25
0
25
50
75
RT (k:)
100
125
o
TEMPERATURE ( C)
Figure 2.
Figure 3.
Soft Start Current vs Temperature
VCC vs ICC, VIN = 12V
8
6
1.05
VCC (V)
NORMALIZED SOFTSTART CURRENT
1.10
1.00
4
2
0.95
0.90
-50
0
-25
0
25
50
75
100
0
125
12
8
4
16
20
24
ICC (mA)
TEMPERATURE (oC)
Figure 4.
Figure 5.
VCC vs VIN, RL = 7kΩ
Error Amplifier Gain/Phase
AVCL = 101
10
50
225
40
180
30
135
4
Ramp Down
20
PHASE
10
45
0
0
GAIN
-10
2
-45
Ramp Up
-20
0
0
2
4
6
8
10
-30
10k
VIN (V)
-90
100k
1M
10M
-135
100M
FREQUENCY (Hz)
Figure 6.
6
90
PHASE (°)
6
GAIN (dB)
VCC (V)
8
Figure 7.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
LM25005
www.ti.com
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
Typical Performance Characteristics (continued)
Demoboard Efficiency
vs IOUT and VIN
100
EFFICIENCY (%)
80
VIN = 7V
60
VIN = 24V
40
20
0
0.0
0.5
1.0
1.5
2.0
2.5
IOUT (A)
Figure 8.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
7
LM25005
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
www.ti.com
Typical Application Circuit and Block Diagram
VIN
7V ± 42V
C1
2.2
3, 4 VIN
C2
2.2
7V
REGULATOR
5 PA
R1
OPEN
LM25005
1.225V
2 SD
STANDBY
VCC
0.7V
C12
OPEN
R2
OPEN
11 SS
BST
UVLO
C7
0.022
DRIVER
S Q
1.225V
20
VIN
DIS
CLK
10 PA
C4
0.01
C8
0.47
THERMAL
SHUTDOWN
UVLO
SHUTDOWN
SD
1
R Q
LEVEL
SHIFT
L1
33 PH
SW 17, 18
PWM
0.7V
C11
330p
PRE 19
C_LIMIT
7 FB
C6
open
C5
0.01
R4
49.9k
ERROR
AMP
1.75V
0.5V/A
+
6 COMP
CLK
Ir
RT
8
RAMP
9
SYNC
R3
21k
8
VIN
TRACK
SAMPLE
and
HOLD
RAMP GENERATOR
Ir = (5 PA x (VIN ± VOUT))
+ 25 PA
OSCILLATOR
SYNC
5
D1
CSHD6-100C
CLK
IS
OUT
12
C10
150
C9
22
15, 16
PGND 13, 14
AGND 10
CLK
R7
10
5V
R5
5.11k
R6
1.65k
C3
330p
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
LM25005
www.ti.com
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
Detailed Operating Description
The LM25005 switching regulator features all of the functions necessary to implement an efficient high voltage
buck regulator using a minimum of external components. This easy to use regulator integrates a 42V N-Channel
buck switch with an output current capability of 2.5 Amps. The regulator control method is based on current
mode control utilizing an emulated current ramp. Peak current mode control provides inherent line voltage feedforward, cycle-by-cycle current limiting, and ease of loop compensation. The use of an emulated control ramp
reduces noise sensitivity of the pulse-width modulation circuit, allowing reliable processing of very small duty
cycles necessary in high input voltage applications. The operating frequency is user programmable from 50kHz
to 500kHz. An oscillator synchronization pin allows multiple LM25005 regulators to self synchronize or be
synchronized to an external clock. The output voltage can be set as low as 1.225V. Fault protection features
include, current limiting, thermal shutdown and remote shutdown capability. The device is available in the
HTSSOP package featuring an exposed pad to aid thermal dissipation.
The functional block diagram and typical application of the LM25005 are shown in the Typical Application Circuit
and Block Diagram. The LM25005 can be applied in numerous applications to efficiently step-down a high,
unregulated input voltage. The device is well suited for telecom, industrial and automotive power bus voltage
ranges.
High Voltage Start-Up Regulator
The LM25005 contains a dual-mode internal high voltage startup regulator that provides the Vcc bias supply for
the PWM controller and boot-strap MOSFET gate driver. The input pin (Vin) can be connected directly to the
input voltage, as high as 42 Volts. For input voltages below 9V, a low dropout switch connects Vcc directly to
Vin. In this supply range, Vcc is approximately equal to Vin. For Vin voltage greater than 9V, the low dropout
switch is disabled and the Vcc regulator is enabled to maintain Vcc at approximately 7V. The wide operating
range of 7V to 42V is achieved through the use of this dual mode regulator.
The output of the Vcc regulator is current limited to 20mA. Upon power up, the regulator sources current into the
capacitor connected to the Vcc pin. When the voltage at the Vcc pin exceeds the Vcc UVLO threshold of 6.3V
and the SD pin is greater than 1.225V, the output switch is enabled and a soft-start sequence begins. The output
switch remains enabled until Vcc falls below 5.3V or the SD pin falls below 1.125V.
An auxiliary supply voltage can be applied to the Vcc pin to reduce the IC power dissipation. If the auxiliary
voltage is greater than 7.3V, the internal regulator will essentially shut off, reducing the IC power dissipation. The
Vcc regulator series pass transistor includes a diode between Vcc and Vin that should not be forward biased in
normal operation. Therefore the auxiliary Vcc voltage should never exceed the Vin voltage.
In high voltage applications extra care should be taken to ensure the Vin pin does not exceed the absolute
maximum voltage rating of 45V. During line or load transients, voltage ringing on the Vin line that exceeds the
Absolute Maximum Ratings can damage the IC. Both careful PC board layout and the use of quality bypass
capacitors located close to the Vin and GND pins are essential.
VIN
9V
VCC
7V
6.3V
Internal Enable Signal
Figure 9. Vin and Vcc Sequencing
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
9
LM25005
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
www.ti.com
Shutdown / Standby
The LM25005 contains a dual level Shutdown (SD) circuit. When the SD pin voltage is below 0.7V, the regulator
is in a low current shutdown mode. When the SD pin voltage is greater than 0.7V but less than 1.225V, the
regulator is in standby mode. In standby mode the Vcc regulator is active but the output switch is disabled. When
the SD pin voltage exceeds 1.225V, the output switch is enabled and normal operation begins. An internal 5µA
pull-up current source configures the regulator to be fully operational if the SD pin is left open.
An external set-point voltage divider from Vin to GND can be used to set the operational input range of the
regulator. The divider must be designed such that the voltage at the SD pin will be greater than 1.225V when Vin
is in the desired operating range. The internal 5µA pull-up current source must be included in calculations of the
external set-point divider. Hysteresis of 0.1V is included for both the shutdown and standby thresholds. The
voltage at the SD pin should never exceed 8V. When using an external set-point divider, it may be necessary to
clamp the SD pin to limit its voltage at high input voltage conditions.
The SD pin can also be used to implement various remote enable / disable functions. Pulling the UVLO pin
below the 0.7V threshold totally disables the controller. If the SD pin voltage is above 1.225V the regulator will be
operational.
Oscillator and Sync Capability
The LM25005 oscillator frequency is set by a single external resistor connected between the RT pin and the
AGND pin. The RT resistor should be located very close to the device and connected directly to the pins of the IC
(RT and AGND).To set a desired oscillator frequency (F), the necessary value for the RT resistor can be
calculated from the following equation:
1 - 580 x 10-9
F
RT =
135 x 10-12
(1)
The SYNC pin can be used to synchronize the internal oscillator to an external clock. The external clock must be
of higher frequency than the free-running frequency set by the RT resistor. A clock circuit with an open drain
output is the recommended interface from the external clock to the SYNC pin. The clock pulse duration should
be greater than 15 ns.
LM25005
LM25005
SYNC
SYNC
SW
SYNC
AGND
CLK
LM25005
SW
SYNC
500 ns
UP TO 5 TOTAL
DEVICES
Figure 10. Sync from External Clock
Figure 11. Sync from Multiple Devices
Multiple LM25005 and/or LM5005 devices can be synchronized together simply by connecting the SYNC pins
together. In this configuration all of the devices will be synchronized to the highest frequency device. The
diagram in Figure 12 illustrates the SYNC input/output features of the LM25005. The internal oscillator circuit
drives the SYNC pin with a strong pull-down / weak pull-up inverter. When the SYNC pin is pulled low either by
the internal oscillator or an external clock, the ramp cycle of the oscillator is terminated and a new oscillator cycle
begins. Thus, if the SYNC pins of several LM25005 IC’s are connected together, the IC with the highest internal
clock frequency will pull the connected SYNC pins low first and terminate the oscillator ramp cycles of the other
IC’s. The LM25005 or LM5005 with the highest programmed clock frequency will serve as the master and control
the switching frequency of the all the devices with lower oscillator frequency.
10
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
LM25005
www.ti.com
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
5V
SYNC
10k
I = f(RT)
2.5V
Q
S
Q
R
DEADTIME
ONE-SHOT
Figure 12. Simplified Oscillator Block Diagram and SYNC I/O Circuit
Error Amplifier and PWM Comparator
The internal high gain error amplifier generates an error signal proportional to the difference between the
regulated output voltage and an internal precision reference (1.225V). The output of the error amplifier is
connected to the COMP pin allowing the user to provide loop compensation components, generally a type II
network, as illustrated in Typical Application Circuit and Block Diagram. This network creates a pole at DC, a
zero and a noise reducing high frequency pole. The PWM comparator compares the emulated current sense
signal from the RAMP generator to the error amplifier output voltage at the COMP pin.
RAMP Generator
The ramp signal used in the pulse width modulator for current mode control is typically derived directly from the
buck switch current. This switch current corresponds to the positive slope portion of the output inductor current.
Using this signal for the PWM ramp simplifies the control loop transfer function to a single pole response and
provides inherent input voltage feed-forward compensation. The disadvantage of using the buck switch current
signal for PWM control is the large leading edge spike due to circuit parasitics that must be filtered or blanked.
Also, the current measurement may introduce significant propagation delays. The filtering, blanking time and
propagation delay limit the minimum achievable pulsewidth. In applications where the input voltage may be
relatively large in comparison to the output voltage, controlling small pulsewidths and duty cycles is necessary for
regulation. The LM25005 utilizes a unique ramp generator, which does not actually measure the buck switch
current but rather reconstructs the signal. Reconstructing or emulating the inductor current provides a ramp
signal to the PWM comparator that is free of leading edge spikes and measurement or filtering delays. The
current reconstruction is comprised of two elements; a sample & hold DC level and an emulated current ramp.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
11
LM25005
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
www.ti.com
RAMP
(5P x (VIN ± VOUT) + 25P) x
tON
CRAMP
Sample and
Hold DC Level
0.5V/A
TON
Figure 13. Composition of Current Sense Signal
The Sample and Hold DC level illustrated in Figure 13. is derived from a measurement of the re-circulating
Schottky diode anode current. The re-circulating diode anode should be connected to the IS pin. The diode
current flows through an internal current sense resistor between the IS and PGND pins. The voltage level across
the sense resistor is sampled and held just prior to the onset of the next conduction interval of the buck switch.
The diode current sensing and sample & hold provide the dc level of the reconstructed current signal. The
positive slope inductor current ramp is emulated by an external capacitor connected from the RAMP pin to AGND
and an internal voltage controlled current source. The ramp current source that emulates the inductor current is a
function of the Vin and Vout voltages per the following equation:
IRAMP = (5µ x (Vin – Vout)) + 25µA
(2)
Proper selection of the RAMP capacitor depends upon the selected value of the output inductor. The value of
CRAMP can be selected from: CRAMP = L x 10-5, where L is the value of the output inductor in Henrys. With this
value, the scale factor of the emulated current ramp will be approximately equal to the scale factor of the dc level
sample and hold ( 0.5 V / A). The CRAMP capacitor should be located very close to the device and connected
directly to the pins of the IC (RAMP and AGND).
For duty cycles greater than 50%, peak current mode control circuits are subject to sub-harmonic oscillation.
Sub-harmonic oscillation is normally characterized by observing alternating wide and narrow pulses at the switch
node. Adding a fixed slope voltage ramp (slope compensation) to the current sense signal prevents this
oscillation. The 25µA of offset current provided from the emulated current source adds some fixed slope to the
ramp signal. In some high output voltage, high duty cycle applications, additional slope may be required. In these
applications, a pull-up resistor may be added between the VCC and RAMP pins to increase the ramp slope
compensation.
For VOUT > 7.5V:
Calculate optimal slope current, IOS = VOUT x 5µA/V.
For example, at VOUT = 10V, IOS = 50µA.
Install a resistor from the RAMP pin to VCC:
RRAMP = VCC / (IOS - 25µA)
12
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
LM25005
www.ti.com
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
VCC
RRAMP
RAMP
CRAMP
Figure 14. RRAMP to VCC for VOUT > 7.5V
Current Limit
The LM25005 contains a unique current monitoring scheme for control and over-current protection. When set
correctly, the emulated current sense signal provides a signal which is proportional to the buck switch current
with a scale factor of 0.5 V / A. The emulated ramp signal is applied to the current limit comparator. If the
emulated ramp signal exceeds 1.75V (3.5A) the present current cycle is terminated (cycle-by-cycle current
limiting). In applications with small output inductance and high input voltage the switch current may overshoot
due to the propagation delay of the current limit comparator. If an overshoot should occur, the diode current
sampling circuit will detect the excess inductor current during the off-time of the buck switch. If the Sample and
Hold DC Level exceeds the 1.75V current limit threshold, the buck switch will be disabled and skip pulses until
the diode current sampling circuit detects the inductor current has decayed below the current limit threshold. This
approach prevents current runaway conditions due to propagation delays or inductor saturation since the inductor
current is forced to decay following any current overshoot.
Soft-Start
The soft-start feature allows the regulator to gradually reach the initial steady state operating point, thus reducing
start-up stresses and surges. The internal soft-start current source, set to 10µA, gradually increases the voltage
of an external soft-start capacitor connected to the SS pin. The soft-start capacitor voltage is connected to the
reference input of the error amplifier. Various sequencing and tracking schemes can be implemented using
external circuits that limit or clamp the voltage level of the SS pin.
In the event a fault is detected (over-temperature, Vcc UVLO, SD) the soft-start capacitor will be discharged.
When the fault condition is no longer present a new soft-start sequence will commence.
Boost Pin
The LM25005 integrates an N-Channel buck switch and associated floating high voltage level shift / gate driver.
This gate driver circuit works in conjunction with an internal diode and an external bootstrap capacitor. A 0.022µF
ceramic capacitor, connected with short traces between the BST pin and SW pin, is recommended. During the
off-time of the buck switch, the SW pin voltage is approximately - 0.5V and the bootstrap capacitor is charged
from Vcc through the internal bootstrap diode. When operating with a high PWM duty cycle, the buck switch will
be forced off each cycle for 500ns to ensure that the bootstrap capacitor is recharged.
Under very light load conditions or when the output voltage is pre-charged, the SW voltage will not remain low
during the off-time of the buck switch. If the inductor current falls to zero and the SW pin rises, the bootstrap
capacitor will not receive sufficient voltage to operate the buck switch gate driver. For these applications, the
PRE pin can be connected to the SW pin to pre-charge the bootstrap capacitor. The internal pre-charge
MOSFET and diode connected between the PRE pin and PGND turns on each cycle for 250ns just prior to the
onset of a new switching cycle. If the SW pin is at a normal negative voltage level (continuous conduction mode),
then no current will flow through the pre-charge MOSFET/diode.
Thermal Protection
Internal Thermal Shutdown circuitry is provided to protect the integrated circuit in the event the maximum junction
temperature is exceeded. When activated, typically at 165 degrees Celsius, the controller is forced into a low
power reset state, disabling the output driver and the bias regulator. This feature is provided to prevent
catastrophic failures from accidental device overheating.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
13
LM25005
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
www.ti.com
APPLICATION INFORMATION
EXTERNAL COMPONENTS
The procedure for calculating the external components is illustrated with the following design example. The Bill of
Materials for this design is listed in 5V, 2.5A Demo Board Bill of Materials. The circuit shown in Typical
Application Circuit and Block Diagram is configured for the following specifications:
• VOUT = 5V
• VIN = 7V to 42V
• Fs = 300 KHz
• Minimum load current (for CCM) = 250 mA
• Maximum load current = 2.5A
R3 (RT)
RT sets the oscillator switching frequency. Generally, higher frequency applications are smaller but have higher
losses. Operation at 300KHz was selected for this example as a reasonable compromise for both small size and
high efficiency. The value of RT for 300KHz switching frequency can be calculated as follows:
[(1 / 300 x 103) ± 580 x 10-9]
RT =
135 x 10-12
(3)
The nearest standard value of 21 kΩ was chosen for RT.
L1
The inductor value is determined based on the operating frequency, load current, ripple current, and the
minimum and maximum input voltage (VIN(min), VIN(max)).
L1 Current
IPK+
IRIPPLE
IO
IPK-
1/Fs
0 mA
Figure 15. Inductor Current Waveform
To keep the circuit in continuous conduction mode (CCM), the maximum ripple current IRIPPLE should be less
than twice the minimum load current, or 0.5 Ap-p. Using this value of ripple current, the value of inductor (L1) is
calculated using the following:
VOUT x (VIN(max) ± VOUT)
L1 =
IRIPPLE x FS x VIN(max)
(4)
5V x (42V ± 5V)
L1 =
= 29 PH
0.5A x 300 kHz x 42V
(5)
This procedure provides a guide to select the value of L1. The nearest standard value (33 µH) will be used. L1
must be rated for the peak current (IPK+) to prevent saturation. During normal loading conditions, the peak current
occurs at maximum load current plus maximum ripple. During an overload condition the peak current is limited to
3.5A nominal (4.25A maximum). The selected inductor (see 5V, 2.5A Demo Board Bill of Materials) has a
conservative 6.2 Amp saturation current rating. For this manufacturer, the saturation rating is defined as the
current necessary for the inductance to reduce by 30%, at 20°C.
14
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
LM25005
www.ti.com
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
C3 (CRAMP)
With the inductor value selected, the value of C3 (CRAMP) necessary for the emulation ramp circuit is:
CRAMP = L x 10-5
where
•
L is in Henrys (With L1 selected for 33µH the recommended value for C3 is 330pF)
(6)
C9, C10
The output capacitors C9, and C10, smooth the inductor ripple current and provide a source of charge for
transient loading conditions. For this design a 22µF ceramic capacitor and a 150µF SP organic capacitor were
selected. The ceramic capacitor provides ultra low ESR to reduce the output ripple voltage and noise spikes,
while the SP capacitor provides a large bulk capacitance in a small volume for transient loading conditions. An
approximation for the output ripple voltage is:
§
¨
©
§
1
'VOUT = 'IL x ¨ESR +
8
x
F
S x COUT
©
(7)
D1
A Schottky type re-circulating diode is required for all LM25005 applications. Ultra-fast diodes are not
recommended and may result in damage to the IC due to reverse recovery current transients. The near ideal
reverse recovery characteristics and low forward voltage drop are particularly important diode characteristics for
high input voltage and low output voltage applications common to the LM25005. The reverse recovery
characteristic determines how long the current surge lasts each cycle when the buck switch is turned on. The
reverse recovery characteristics of Schottky diodes minimize the peak instantaneous power in the buck switch
occurring during turn-on each cycle. The resulting switching losses of the buck switch are significantly reduced
when using a Schottky diode. The reverse breakdown rating should be selected for the maximum VIN, plus some
safety margin.
The forward voltage drop has a significant impact on the conversion efficiency, especially for applications with a
low output voltage. “Rated” current for diodes vary widely from various manufactures. The worst case is to
assume a short circuit load condition. In this case the diode will carry the output current almost continuously. For
the LM25005 this current can be as high as 3.5A. Assuming a worst case 1V drop across the diode, the
maximum diode power dissipation can be as high as 3.5W. For the reference design a 60V Schottky in a DPAK
package was selected.
C1, C2
The regulator supply voltage has a large source impedance at the switching frequency. Good quality input
capacitors are necessary to limit the ripple voltage at the VIN pin while supplying most of the switch current
during the on-time. When the buck switch turns on, the current into the VIN pin steps to the lower peak of the
inductor current waveform, ramps up to the peak value, then drops to zero at turn-off. The average current into
VIN during the on-time is the load current. The input capacitance should be selected for RMS current rating and
minimum ripple voltage. A good approximation for the required ripple current rating necessary is IRMS > IOUT / 2.
Quality ceramic capacitors with a low ESR should be selected for the input filter. To allow for capacitor
tolerances and voltage effects, two 2.2 µF, 100V ceramic capacitors will be used. If step input voltage transients
are expected near the maximum rating of the LM25005, a careful evaluation of ringing and possible spikes at the
device VIN pin should be completed. An additional damping network or input voltage clamp may be required in
these cases.
C8
The capacitor at the VCC pin provides noise filtering and stability for the VCC regulator. The recommended value
of C8 should be no smaller than 0.1 µF, and should be a good quality, low ESR, ceramic capacitor. A value of
0.47 µF was selected for this design.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
15
LM25005
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
www.ti.com
C7
The bootstrap capacitor between the BST and the SW pins supplies the gate current to charge the buck switch
gate at turn-on. The recommended value of C7 is 0.022 µF, and should be a good quality, low ESR, ceramic
capacitor.
C4
The capacitor at the SS pin determines the soft-start time, i.e. the time for the reference voltage and the output
voltage, to reach the final regulated value. The time is determined from:
C4 x 1.225V
tss =
10 PA
(8)
For this application, a C4 value of 0.01 µF was chosen which corresponds to a soft-start time of 1 ms.
R5, R6
R5 and R6 set the output voltage level, the ratio of these resistors is calculated from:
R5/R6 = (VOUT / 1.225V) - 1
(9)
For a 5V output, the R5/R6 ratio calculates to 3.082. The resistors should be chosen from standard value
resistors, a good starting point is selection in the range of 1.0 kΩ - 10 kΩ. Values of 5.11 kΩ for R5, and 1.65 kΩ
for R6 were selected.
R1, R2, C12
A voltage divider can be connected to the SD pin to set a minimum operating voltage Vin(min) for the regulator. If
this feature is required, the easiest approach to select the divider resistor values is to select a value for R1
(between 10 kΩ and 100 kΩ recommended) then calculate R2 from:
§
¨
©
§
R1
R2 = 1.225 x ¨
-6
© VIN(min) + (5 x 10 x R1) ± 1.225
(10)
Capacitor C12 provides filtering for the divider. The voltage at the SD pin should never exceed 8V, when using
an external set-point divider it may be necessary to clamp the SD pin at high input voltage conditions. The
reference design utilizes the full range of the LM25005 (7V to 42V); therefore these components can be omitted.
With the SD pin open circuit the LM25005 responds once the Vcc UVLO threshold is satisfied.
R7, C11
A snubber network across the power diode reduces ringing and spikes at the switching node. Excessive ringing
and spikes can cause erratic operation and couple spikes and noise to the output. In the limit, spikes beyond the
rating of the LM25005 or the re-circulating diode can damage these devices. Selecting the values for the snubber
is best accomplished through empirical methods. First, make sure the lead lengths for the snubber connections
are very short. For the current levels typical for the LM25005 a resistor value between 5 and 20 Ohms is
adequate. Increasing the value of the snubber capacitor results in more damping but higher losses. Select a
minimum value of C11 that provides adequate damping of the SW pin waveform at high load.
16
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
LM25005
www.ti.com
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
R4, C5, C6
These components configure the error amplifier gain characteristics to accomplish a stable overall loop gain. One
advantage of current mode control is the ability to close the loop with only two feedback components, R4 and C5.
The overall loop gain is the product of the modulator gain and the error amplifier gain. The DC modulator gain of
the LM25005 is as follows:
DC Gain(MOD) = Gm(MOD) x RLOAD = 2 x RLOAD
(11)
The dominant low frequency pole of the modulator is determined by the load resistance (RLOAD,) and output
capacitance (COUT). The corner frequency of this pole is:
fp(MOD) = 1 / (2π RLOAD COUT)
(12)
For RLOAD = 5 Ω and COUT = 177 µF then fp(MOD) = 180Hz
DC Gain(MOD) = 2 x 5 = 10 = 20 dB
For the design example of Typical Application Circuit and Block Diagram the following modulator gain vs.
frequency characteristic was measured as shown in Figure 16.
REF LEVEL
0.000 dB
0.0 deg
/DIV
10.000 dB
45.000 deg
GAIN
0
PHASE
100
1k
START 50.000 Hz
10k
STOP 50 000.000 Hz
Figure 16. Gain and Phase of Modulator
RLOAD = 5 Ohms and COUT = 177 µF
Components R4 and C5 configure the error amplifier as a type II configuration which has a pole at DC and a
zero at fZ = 1 / (2πR4C5). The error amplifier zero cancels the modulator pole leaving a single pole response at
the crossover frequency of the loop gain. A single pole response at the crossover frequency yields a very stable
loop with 90 degrees of phase margin.
For the design example, a target loop bandwidth (crossover frequency) of 20 kHz was selected. The
compensation network zero (fZ) should be selected at least an order of magnitude less than the target crossover
frequency. This constrains the product of R4 and C5 for a desired compensation network zero 1 / (2π R4 C5) to
be less than 2kHz. Increasing R4 while proportionally decreasing C5, increases the error amp gain. Conversely,
decreasing R4 while proportionally increasing C5, decreases the error amp gain. For the design example C5 was
selected for 0.01µF and R4 was selected for 49.9 kΩ. These values configure the compensation network zero at
320 Hz. The error amp gain at frequencies greater than fZ is: R4 / R5, which is approximately 10 (20dB).
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
17
LM25005
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
www.ti.com
REF LEVEL
0.000 dB
0.0 deg
/DIV
10.000 dB
45.000 deg
PHASE
GAIN
0
100
1k
START 50.000 Hz
10k
STOP 50 000.000 Hz
Figure 17. Error Amplifier Gain and Phase
The overall loop can be predicted as the sum (in dB) of the modulator gain and the error amp gain.
REF LEVEL
0.000 dB
0.0 deg
/DIV
10.000 dB
45.000 deg
GAIN
PHASE
0
100
1k
START 50.000 Hz
10k
STOP 50 000.000 Hz
Figure 18. Overall Loop Gain and Phase
If a network analyzer is available, the modulator gain can be measured and the error amplifier gain can be
configured for the desired loop transfer function. If a network analyzer is not available, the error amplifier
compensation components can be designed with the guidelines given. Step load transient tests can be
performed to verify acceptable performance. The step load goal is minimum overshoot with a damped response.
C6 can be added to the compensation network to decrease noise susceptibility of the error amplifier. The value
of C6 must be sufficiently small since the addition of this capacitor adds a pole in the error amplifier transfer
function. This pole must be well beyond the loop crossover frequency. A good approximation of the location of
the pole added by C6 is: fp2 = fz x C5 / C6.
18
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
LM25005
www.ti.com
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
BIAS POWER DISSIPATION REDUCTION
Buck regulators operating with high input voltage can dissipate an appreciable amount of power for the bias of
the IC. The VCC regulator must step-down the input voltage VIN to a nominal VCC level of 7V. The large voltage
drop across the VCC regulator translates into a large power dissipation within the Vcc regulator. There are several
techniques that can significantly reduce this bias regulator power dissipation. Figure 19 and Figure 20 depict two
methods to bias the IC from the output voltage. In each case the internal Vcc regulator is used to initially bias the
VCC pin. After the output voltage is established, the VCC pin potential is raised above the nominal 7V regulation
level, which effectively disables the internal VCC regulator. The voltage applied to the VCC pin should never
exceed 14V. The VCC voltage should never be larger than the VIN voltage.
LM25005
BST
VOUT
SW
L1
COUT
D1
IS
GND
VCC
D2
Figure 19. VCC Bias from VOUT for 8V < VOUT < 14V
LM25005
BST
VOUT
L1
SW
D1
COUT
IS
GND
D2
VCC
Figure 20. VCC Bias with Additional Winding on the Output Inductor
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
19
LM25005
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
www.ti.com
PCB LAYOUT AND THERMAL CONSIDERATIONS
The circuit in theTypical Application Circuit and Block Diagram serves as both a block diagram of the LM25005
and a typical application board schematic for the LM25005. In a buck regulator there are two loops where
currents are switched very fast. The first loop starts from the input capacitors, to the regulator VIN pin, to the
regulator SW pin, to the inductor then out to the load. The second loop starts from the output capacitor ground,
to the regulator PGND pins, to the regulator IS pins, to the diode anode, to the inductor and then out to the load.
Minimizing the loop area of these two loops reduces the stray inductance and minimizes noise and possible
erratic operation. A ground plane in the PC board is recommended as a means to connect the input filter
capacitors to the output filter capacitors and the PGND pins of the regulator. Connect all of the low power ground
connections (CSS, RT, CRAMP) directly to the regulator AGND pin. Connect the AGND and PGND pins together
through the topside copper area covering the entire underside of the device. Place several vias in this underside
copper area to the ground plane.
The two highest power dissipating components are the re-circulating diode and the LM25005 regulator IC. The
easiest method to determine the power dissipated within the LM25005 is to measure the total conversion losses
(Pin – Pout) then subtract the power losses in the Schottky diode, output inductor and snubber resistor. An
approximation for the Schottky diode loss is P = (1-D) x Iout x Vfwd. An approximation for the output inductor
power is P = IOUT2 x R x 1.1, where R is the DC resistance of the inductor and the 1.1 factor is an approximation
for the ac losses. If a snubber is used, the power loss can be estimated with an oscilloscope by observation of
the resistor voltage drop at both turn-on and turn-off transitions. The regulator has an exposed thermal pad to aid
power dissipation. Adding several vias under the device to the ground plane will greatly reduce the regulator
junction temperature. Selecting a diode with an exposed pad will aid the power dissipation of the diode.
5V, 2.5A Demo Board Bill of Materials
ITEM
20
PART NUMBER
DESCRIPTION
VALUE
C
1
C4532X7R2A225M
CAPACITOR, CER, TDK
2.2µ, 100V
C
2
C4532X7R2A225M
CAPACITOR, CER, TDK
2.2µ, 100V
C
3
C0805C331G1GAC
CAPACITOR, CER, KEMET
330p, 100V
C
4
C2012X7R2A103K
CAPACITOR, CER, TDK
0.01µ, 100V
C
5
C2012X7R2A103K
CAPACITOR, CER, TDK
0.01µ, 100V
C
6
OPEN
NOT USED
C
7
C2012X7R2A223K
CAPACITOR, CER, TDK
0.022µ, 100V
C
8
C2012X7R1C474M
CAPACITOR, CER, TDK
0.47µ, 16V
C
9
C3225X7R1C226M
CAPACITOR, CER, TDK
C
10
EEFHE0J151R
CAPACITOR, SP, PANASONIC
150µ, 6.3V
C
11
C0805C331G1GAC
CAPACITOR, CER, KEMET
330p, 100V
C
12
OPEN
NOT USED
D
1
CSHD6-60C
DIODE, 60V, CENTRAL
6CWQ10FN
DIODE, 100V, IR (D1-ALT)
22µ, 16V
L
1
DR127-330
INDUCTOR, COOPER
R
1
OPEN
NOT USED
R
2
OPEN
NOT USED
R
3
CRCW08052102F
RESISTOR
21K
R
4
CRCW08054992F
RESISTOR
49.9K
R
5
CRCW08055111F
RESISTOR
5.11K
R
6
CRCW08051651F
RESISTOR
1.65K
R
7
CRCW2512100J
RESISTOR
10, 1W
U
1
LM25005
REGULATOR, TEXAS INSTRUMENTS
Submit Documentation Feedback
33µH
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
LM25005
www.ti.com
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
PCB Layout
Figure 21. Component Side
Figure 22. Solder Side
Figure 23. Silkscreen
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
21
LM25005
SNVS411C – JANUARY 2006 – REVISED MARCH 2013
www.ti.com
REVISION HISTORY
Changes from Revision B (March 2013) to Revision C
•
22
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 20
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM25005
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM25005MH
NRND
HTSSOP
PWP
20
73
TBD
Call TI
Call TI
-40 to 125
LM25005
MH
LM25005MH/NOPB
ACTIVE
HTSSOP
PWP
20
73
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LM25005
MH
LM25005MHX/NOPB
ACTIVE
HTSSOP
PWP
20
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LM25005
MH
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
LM25005MHX/NOPB
Package Package Pins
Type Drawing
SPQ
HTSSOP
2500
PWP
20
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
330.0
16.4
Pack Materials-Page 1
6.95
B0
(mm)
K0
(mm)
P1
(mm)
7.1
1.6
8.0
W
Pin1
(mm) Quadrant
16.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM25005MHX/NOPB
HTSSOP
PWP
20
2500
367.0
367.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
PWP0020A
MXA20A (Rev C)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated