TI MC1489AD Quadruple line receiver Datasheet

MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A
QUADRUPLE LINE RECEIVERS
SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998
D
D
description
These devices are monolithic low-power Schottky
quadruple line receivers designed to satisfy the
requirements of the standard interface between
data-terminal equipment and data-communication equipment as defined by TIA / EIA-232-F. A
separate response-control (CONT) terminal is
provided for each receiver. A resistor or a resistor
and bias-voltage source can be connected
between this terminal and ground to shift the input
threshold levels. An external capacitor can be
connected between this terminal and ground to
provide input noise filtering.
The SN55189 and SN55189A are characterized
for operation over the full military temperature
range of – 55°C to 125°C. The MC1489,
MC1489A, SN75189, and SN75189A are
characterized for operation from 0°C to 70°C.
SN55189, SN55189A . . . J OR W PACKAGE
MC1489, MC1489A, SN75189, SN75189A
D, N, OR NS† PACKAGE
(TOP VIEW)
1A
1CONT
1Y
2A
2CONT
2Y
GND
1
14
2
13
3
12
4
11
5
10
6
9
7
8
VCC
4A
4CONT
4Y
3A
3CONT
3Y
† The NS package is only available left-end taped and reeled.
For SN75189, order SN75189NSR.
SN55189, SN55189A . . . FK PACKAGE
(TOP VIEW)
1CONT
1A
NC
VCC
4A
D
Input Resistance . . . 3 kΩ to 7 kΩ
Input Signal Range . . . ± 30 V
Operate From Single 5-V Supply
Built-In Input Hysteresis (Double
Thresholds)
Response Control that Provides:
Input Threshold Shifting
Input Noise Filtering
Meet or Exceed the Requirements of
TIA / EIA-232-F and ITU Recommendation
V.28
Fully Interchangeable With Motorola
MC1489 and MC1489A
1Y
NC
2A
NC
2CONT
4
3 2 1 20 19
18
5
17
6
16
7
15
8
14
9 10 11 12 13
4CONT
NC
4Y
NC
3A
2Y
GND
NC
3Y
3CONT
D
D
D
D
NC – No internal connection
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Motorola is a trademark of Motorola, Incorporated.
Copyright  1998, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
On products compliant to MIL-PRF-38535, all parameters are tested
unless otherwise noted. On all other products, production
processing does not necessarily include testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A
QUADRUPLE LINE RECEIVERS
SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998
logic symbol†
1A
1 CONT
2A
2 CONT
3A
3 CONT
1
2
4
3 1Y
THRS ADJ
6 2Y
5
10
8 3Y
9
13
11 4Y
4A
4 CONT 12
† This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
Pin numbers shown are for the D, J, N, NS, and W packages.
logic diagram (positive logic)
A
Y
Response
Control
schematic (each receiver)
VCC
9 kΩ
5 kΩ
1.66 kΩ
Output Y
R1
Response
Control
4 kΩ
Input A
10 kΩ
GND
R1
MC1489
SN55189
SN75189
MC1489A
SN55189A
SN75189A
8.4 kΩ
1.84 kΩ
Resistor values shown are nominal.
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A
QUADRUPLE LINE RECEIVERS
SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998
absolute maximum ratings over operating free-air temperature (unless otherwise noted)†
Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 V
Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±30 V
Output voltage, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA: SN55189, SN55189A . . . . . . . . . . . . . . . . . . . . . . – 55°C to 125°C
MC1489, MC1489A, SN75189, SN75189A . . . . . . 0°C to 70°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Case temperature for 60 seconds, FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J or W package . . . . . . . . . . . . . . . . 300°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, N, or NS package . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values are with respect to the network ground terminal.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 125°C
POWER RATING
D
950 mW
7.6 mW/°C
608 mW
N/A
FK
J‡
1375 mW
11.0 mW/°C
880 mW
275 mW
1375 mW
11.0 mW/°C
880 mW
275 mW
N
1150 mW
9.2 mW/°C
736 mW
N/A
NS
625 mW
4.0 mW/°C
445 mW
N/A
W
1000 mW
8.0 mW/°C
640 mW
‡ In the J package, SN55189 and SN55189A chips are either silver glass or alloy mounted.
200 mW
recommended operating conditions
MIN
NOM
MAX
Supply voltage, VCC
4.5
5
5.5
V
Input voltage, VI
–25
25
V
High-level output current, IOH
Low-level output current, IOL
Operating free-air temperature, TA
0
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
UNIT
–0.5
mA
10
mA
70
°C
3
MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A
QUADRUPLE LINE RECEIVERS
SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998
electrical characteristics over operating free-air temperature range, VCC = 5 V ± 1% (unless
otherwise noted)
TEST
FIGURE
PARAMETER
TEST CONDITIONS†
VIT
IT+
Positive-going
g g input
threshold voltage
TA = – 55°C to 125°C
TA = 25°C
1
’89A
VIT–
Negative-going
N
ti
i input
i
t
threshold voltage
1
VOH
High-level
g
output voltage
1
VOL
Low-level
output voltage
IIH
’89, ’89A
TA = 0°C to 70°C
TA = – 55°C to 125°C
TA = 25°C
TA = 0°C to 70°C
TA = – 55°C to 125°C
VI = 0.75 V, IOH = – 0.5 mA
UNIT
MIN
TYP‡
MAX
MIN
TYP‡
MAX
1
1.3
1.5
1
1.3
1.5
TA = 25°C
TA = 0°C to 70°C
’89
MC1489, MC1489A
SN75189
SN75189A
SN55189
SN55189A
0.9
0.6
1.75
1.6
1.9
1.9
2.25
1.75
1.9
1.55
1.30
0.75
2.25
V
2.25
2.65
1.0
1.25
0.75
1.0
0.65
0.35
1.25
1.25
V
1.6
2.6
4
5
2.6
4
5
2.6
4
5
2.6
4
5
02
0.2
0 45
0.45
02
0.2
0 45
0.45
Input open,
IOH = – 0.5 mA
1
VI = 3 V
V,
IOL = 10 mA
High-level
g
input current
2
VI = 25 V
VI = 3 V
IIL
Low-level
input current
2
VI = – 25 V
VI = – 3 V
IOS
Short-circuit
output current
3
–3
ICC
Supply current
2
VI = 5 V,
Outputs open
† All characteristics are measured with the response-control terminal open.
‡ All typical values are at VCC = 5 V, TA = 25°C.
20
3.6
8.3
0.43
3.6
8.3
0.43
– 3.6
– 8.3
– 0.43
– 3.6
–8.3
– 0.43
3
–3
26
V
V
mA
mA
mA
20
26
TYP
MAX
RL = 3.9 kΩ
25
85
RL = 390 Ω
25
50
RL = 3.9 kΩ
120
175
RL = 390 Ω
10
20
mA
switching characteristics, VCC = 5 V, CL = 15 pF, TA = 25°C
TEST
FIGURE
PARAMETER
tPLH
tPHL
Propagation delay time, low- to high-level output
tTLH
tTHL
Transition time, low- to high-level output
4
Propagation delay time, high- to low-level output
Transition time, high- to low-level output
POST OFFICE BOX 655303
4
TEST CONDITIONS
• DALLAS, TEXAS 75265
MIN
UNIT
ns
ns
MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A
QUADRUPLE LINE RECEIVERS
SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998
PARAMETER MEASUREMENT INFORMATION†
VCC
VIT, V1
– IOH
VOH
Response
Control
Open
Unless
Otherwise
Specified
VOL
RC
IOL
RC
CC
– VC
+VC
Figure 1. VIT + , VIT – , VOH , VOL
VCC
ICC (see Note A)
VI
IIH
Open
IIL
Response Control Open
NOTE A: ICC is tested for all four receivers simultaneously.
Figure 2. IIH , IIL , ICC
VCC
– IOS
Response
Control
Open
Figure 3. IOS
† Arrows indicate actual direction of current flow. Current into a terminal is a positive value.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A
QUADRUPLE LINE RECEIVERS
SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998
PARAMETER MEASUREMENT INFORMATION
VCC
Output
RL
Pulse
Generator
(see Note A)
See Note C
CL = 15 pF
(see Note B)
Response
Control
Open
TEST CIRCUIT
≤10 ns
≤10 ns
Input
10%
90%
50%
90%
50%
90%
10%
0V
tPLH
tPHL
Output
4V
VOH
50%
10%
90%
50%
10%
tTHL
VOL
tTLH
VOLTAGE WAVEFORMS
NOTES: A. The pulse generator has the following characteristics: ZO = 50 Ω, tw = 500 ns.
B. CL includes probe and jig capacitances.
C. All diodes are 1N3064 or equivalent.
Figure 4. Test Circuit and Voltage Waveforms
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A
QUADRUPLE LINE RECEIVERS
SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998
TYPICAL CHARACTERISTICS
SN65189, SN75189
OUTPUT VOLTAGE
vs
INPUT VOLTAGE
ÁÁÁ ÁÁÁÁ ÎÎÎÎ ÁÁÁÁ ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁ ÁÁÁÁ
ÁÁÁÁ ÁÁÁÁÁ
ÁÁÁ ÁÁÁÁ
ÁÁÁÁ ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎ
6
V
VO
O – Output Voltage – V
5
4
3
VIT–
2
RC = ∞
RC = 13 kΩ
VC = 5 V
RC = 5 kΩ
VC = 5 V
VIT+
VIT+
VIT–
RC = 11 kΩ
VC = – 5 V
VIT+
VIT–
VCC = 5 V
TA = 25°C
See Figure 1
VIT+
VIT–
1
0
–3
–1
–2
0
1
VI – Input Voltage – V
2
3
4
5
Figure 5
ÁÁÁÁ
ÁÁÁÁ
6
VO
V
O – Output Voltage – V
SN65189A, SN75189A
OUTPUT VOLTAGE
vs
INPUT VOLTAGE
ÎÎÎÎ
ÎÎÎÎ
5
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
RC = ∞
RC = 5 kΩ
VC = 5 V
VCC = 5 V
TA = 25°C
See Figure 1
RC = 11 kΩ
VC = – 5 V
4
3
VIT–
VIT+
VIT–
VIT+
VIT–
VIT+
2
1
0
–3
–2
–1
0
1
VI – Input Voltage – V
2
3
4
5
Figure 6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A
QUADRUPLE LINE RECEIVERS
SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998
TYPICAL CHARACTERISTICS†
INPUT THRESHOLD VOLTAGE
vs
SUPPLY VOLTAGE
2.4
2
2.2
1.8
2
’89A VIT+
1.8
1.6
’89 VIT+
1.4
1.2
’89 VIT–
1
’89A VIT–
0.8
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
’89A VIT+
1.6
V IT – Input Threshold Voltage – V
V IT – Input Threshold Voltage – V
INPUT THRESHOLD VOLTAGE
vs
FREE-AIR TEMPERATURE
’89 VIT–
1.4
1.2
’89 VIT+
1
’89A VIT–
0.8
0.6
0.4
0.6
0.2
0.4
– 100 – 75 – 50 – 25
0
25
50
0
2
75 100 125 150
3
4
TA – Free-Air Temperature – °C
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎ
ÁÁÁÁÁ
ÎÎÎÎÎ
ÁÁÁÁÁ
ÎÎÎÎÎ
6
6
VCC = 5 V
TA = 25°C
See Note A
ÎÎÎÎÎ
ÎÎÎÎÎ
ÁÁÁÁ
ÎÎÎÎÎ
ÁÁÁÁ
ÎÎÎÎÎ
ÁÁÁÁ
CC = 300 pF
3
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
Amplitude – V
CC = 500 pF
4
3
CC = 10 pF
1
CC = 100 pF
0
10
40
100
CC = 500 pF
ÁÁÁÁ
ÁÁÁÁ
ÎÎÎÎÎ
ÁÁÁÁ
ÎÎÎÎÎ
ÁÁÁÁ
CC = 12 pF
2
2
VCC = 5 V
TA = 25°C
See Note A
5
CC = 300 pF
4
CC = 100 pF
1
400
1000
4000 10000
0
10
40
100
400
4000 10000
NOTE A: Maximum amplitude of a positive-going pulse that,
starting from 0 V, will not cause a change in the
output level.
Figure 9
Figure 10
† Data for free-air temperatures below 0°C and above 70°C are applicable to SN55189 and SN55189A circuits only.
POST OFFICE BOX 655303
1000
tw – Pulse Duration – ns
tw – Pulse Duration – ns
NOTE A: Maximum amplitude of a positive-going pulse that,
starting from 0 V, will not cause a change in the
output level.
8
10
SN75189A
NOISE REJECTION
SN75189
NOISE REJECTION
5
9
Figure 8
Figure 7
Amplitude – V
5
6
7
8
VCC – Supply Voltage – V
• DALLAS, TEXAS 75265
MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A
QUADRUPLE LINE RECEIVERS
SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998
TYPICAL CHARACTERISTICS
INPUT CURRENT
vs
INPUT VOLTAGE
10
8
IIII – Input Current – mA
6
4
ÎÎÎÎÎ
ÁÁÁÁ
ÎÎÎÎÎ
ÎÎÎÎÎ
VCC = 5 V
Control Open
TA = 25°C
2
0
–2
–4
–6
–8
–10
– 25 – 20 –15 –10 – 5
0
5 10
VI – Input Voltage – V
15
20
25
Figure 11
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  1998, Texas Instruments Incorporated