Features • AVR - High Performance and Low Power RISC Architecture • 118 Powerful Instructions - Most Single Clock Cycle Execution • 8K bytes of In-System Reprogrammable Flash • • • • • • • • • • • • • • • • • – SPI Serial Interface for Program Downloading – Endurance: 1,000 Write/Erase Cycles 512 bytes EEPROM – Endurance: 100,000 Write/Erase Cycles 512 bytes Internal SRAM 32 x 8 General Purpose Working Registers 32 Programmable I/O Lines Programmable Serial UART SPI Serial Interface VCC: 2.7 - 6.0V Fully Static Operation – 0 - 8 MHz 4.0 - 6.0V, – 0 - 4 MHz 2.7 - 4.0V Up to 8 MIPS Throughput at 8 MHz One 8-Bit Timer/Counter with Separate Prescaler One 16-Bit Timer/Counter with Separate Prescaler and Compare and Capture Modes Dual PWM External and Internal Interrupt Sources Programmable Watchdog Timer with On-Chip Oscillator On-Chip Analog Comparator Low Power Idle and Power Down Modes Programming Lock for Software Security 8-Bit Microcontroller with 8K bytes In-System Programmable Flash AT90S8515 Preliminary Description The AT90S8515 is a low-power CMOS 8-bit microcontroller based on the AVR ® enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the AT90S8515 achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed. The AVR core combines a rich instruction set with 32 general purpose working registers. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to be accessed in one single instruction executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers. (continued) Pin Configurations Rev. 0841DS–06/98 Note: This is a sumary document. For the complete 76 page document, please visit our Web site at www.atmel.com or e-mail at [email protected] and request literature number 0841D. 1 Block Diagram Figure 1. The AT90S8515 Block Diagram The AT90S8515 provides the following features: 8K bytes of In-System Programmable Flash, 512 bytes EEPROM, 512 bytes SRAM, 32 general purpose I/O lines, 32 general purpose working registers, flexible timer/counters with compare modes, internal and external interrupts, a programmable serial UART, programmable Watchdog Timer with internal oscillator, an SPI serial port and two software selectable power saving modes. The Idle Mode stops the CPU while allowing the SRAM, timer/counters, SPI port and interrupt system to continue functioning. The power down mode saves the register contents but freezes the oscillator, disabling all other chip functions until the next interrupt or hardware reset. 2 AT90S8515 The device is manufactured using Atmel’s high density non-volatile memory technology. The on-chip in-system programmable Flash allows the program memory to be reprogrammed in-system through an SPI serial interface or by a conventional nonvolatile memory programmer. By combining an enhanced RISC 8-bit CPU with In-System Programmable Flash on a monolithic chip, the Atmel AT90S8515 is a powerful microcontroller that provides a highly flexible and cost effective solution to many embedded control applications. The AT90S8515 AVR is supported with a full suite of program and system development tools including: C compilers, macro assemblers, program debugger/simulators, incircuit emulators, and evaluation kits. AT90S8515 Pin Descriptions VCC Supply voltage GND Ground Port A (PA7..PA0) Port A is an 8-bit bidirectional I/O port. Port pins can provide internal pull-up resistors (selected for each bit). The Port A output buffers can sink 20mA and can drive LED displays directly. When pins PA0 to PA7 are used as inputs and are externally pulled low, they will source current if the internal pull-up resistors are activated. Port A serves as Multiplexed Address/Data input/output when using external SRAM. ALE ALE is the Address Latch Enable used when the External Memory is enabled. The ALE strobe is used to latch the low-order address (8 bits) into an address latch during the first access cycle, and the AD0-7 pins are used for data during the second access cycle. Crystal Oscillator XTAL1 and XTAL2 are input and output, respectively, of an inverting amplifier which can be configured for use as an on-chip oscillator, as shown in Figure 2. Either a quartz crystal or a ceramic resonator may be used. To drive the device from an external clock source, XTAL2 should be left unconnected while XTAL1 is driven as shown in Figure 3. Figure 2. Oscillator Connections Port B (PB7..PB0) Port B is an 8-bit bidirectional I/O pins with internal pull-up resistors. The Port B output buffers can sink 20 mA. As inputs, Port B pins that are externally pulled low will source current if the pull-up resistors are activated. Port B also serves the functions of various special features of the AT90S8515 as listed on page 46. Port C (PC7..PC0) Port C is an 8-bit bidirectional I/O port with internal pull-up resistors. The Port C output buffers can sink 20 mA. As inputs, Port C pins that are externally pulled low will source current if the pull-up resistors are activated. Port C also serves as Address output when using external SRAM. Port D (PD7..PD0) Port D is an 8-bit bidirectional I/O port with internal pull-up resistors. The Port D output buffers can sink 20 mA. As inputs, Port D pins that are externally pulled low will source current if the pull-up resistors are activated. Port D also serves the functions of various special features of the AT90S8515 as listed on page 52. Figure 3. External Clock Drive Configuration RESET Reset input. A low on this pin for two machine cycles while the oscillator is running resets the device. XTAL1 Input to the inverting oscillator amplifier and input to the internal clock operating circuit. XTAL2 Output from the inverting oscillator amplifier ICP ICP is the input pin for the Timer/Counter1 Input Capture function. OC1B OC1B is the output pin for the Timer/Counter1 Output CompareB function 3 AT90S8515 Architectural Overview The fast-access register file concept contains 32 x 8-bit general purpose working registers with a single clock cycle access time. This means that during one single clock cycle, one ALU (Arithmetic Logic Unit) operation is executed. Two operands are output from the register file, the operation is executed, and the result is stored back in the register file in one clock cycle. Six of the 32 registers can be used as three 16-bits indirect address register pointers for Data Space addressing enabling efficient address calculations. One of the three address pointers is also used as the address pointer for the constant table look up function. These added function registers are the 16-bits X-register, Y-register and Z-register. Figure 4. The AT90S8515 AVR Enhanced RISC Architecture The ALU supports arithmetic and logic functions between registers or between a constant and a register. Single register operations are also executed in the ALU. Figure 4 shows the AT90S8515 AVR Enhanced RISC microcontroller architecture. In addition to the register operation, the conventional memory addressing modes can be used on the register file as well. This is enabled by the fact that the register file is assigned the 32 lowermost Data Space addresses ($00 $1F), allowing them to be accessed as though they were ordinary memory locations. The I/O memory space contains 64 addresses for CPU peripheral functions as Control Registers, Timer/Counters, A/D-converters, and other I/O functions. The I/O Memory can be accessed directly, or as the Data Space locations following those of the register file, $20 - $5F. 4 AT90S8515 The AVR uses a Harvard architecture concept - with separate memories and buses for program and data. The program memory is executed with a two stage pipeline. While one instruction is being executed, the next instruction is pre-fetched from the program memory. This concept enables instructions to be executed in every clock cycle. The program memory is in-system programmable Flash memory. With the relative jump and call instructions, the whole 4K address space is directly accessed. Most AVR instructions have a single 16-bit word format. Every program memory address contains a 16- or 32-bit instruction. During interrupts and subroutine calls, the return address program counter (PC) is stored on the stack. The stack is effectively allocated in the general data SRAM, and consequently the stack size is only limited by the total SRAM size and the usage of the SRAM. All user programs must initial- AT90S8515 ize the SP in the reset routine (before subroutines or interrupts are executed). The 16-bit stack pointer SP is read/write accessible in the I/O space. The 512 bytes data SRAM can be easily accessed through the five different addressing modes supported in the AVR architecture. The memory spaces in the AVR architecture are all linear and regular memory maps. A flexible interrupt module has its control registers in the I/O space with an additional global interrupt enable bit in the status register. All the different interrupts have a separate interrupt vector in the interrupt vector table at the beginning of the program memory. The different interrupts have priority in accordance with their interrupt vector position. The lower the interrupt vector address the higher the priority. Figure 5. Memory Maps 5 AT90S8515 Register Summary 6 Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page $3F ($5F) $3E ($5E) $3D ($5D) $3C ($5C) $3B ($5B) $3A ($5A) $39 ($59) $38 ($58) $37 ($57) $36 ($56) $35 ($55) $34 ($54) $33 ($53) $32 ($52) $31 ($51) $30 ($50) $2F ($4F) $2E ($4E) $2D ($4D) $2C ($4C) $2B ($4B) $2A ($4A) $29 ($49) $28 ($48) $27 ($47) $26 ($46) $25 ($45) $24 ($44) $23 ($43) $22 ($42) $21 ($41) $20 ($40) $1F ($3F) $1E ($3E) $1D ($3D) $1C ($3C) $1B ($3B) $1A ($3A) $19 ($39) $18 ($38) $17 ($37) $16 ($36) $15 ($35) $14 ($34) $13 ($33) $12 ($32) $11 ($31) $10 ($30) $0F ($2F) $0E ($2E) $0D ($2D) $0C ($2C) $0B ($2B) $0A ($2A) $09 ($29) $08 ($28) … $00 ($20) SREG SPH SPL Reserved GIMSK GIFR TIMSK TIFR Reserved Reserved MCUCR Reserved TCCR0 TCNT0 Reserved Reserved TCCR1A TCCR1B TCNT1H TCNT1L OCR1AH OCR1AL OCR1BH OCR1BL Reserved Reserved ICR1H ICR1L Reserved Reserved WDTCR Reserved Reserved EEARL EEDR EECR PORTA DDRA PINA PORTB DDRB PINB PORTC DDRC PINC PORTD DDRD PIND SPDR SPSR SPCR UDR USR UCR UBRR ACSR Reserved Reserved I SP15 SP7 T SP14 SP6 H SP13 SP5 S SP12 SP4 V SP11 SP3 N SP10 SP2 Z SP9 SP1 C SP8 SP0 18 19 19 INT1 INTF1 TOIE1 TOV1 INT0 INTF0 OCIE1A OCF1A - - - - - - OCIE1B OCF1B - TICIE1 ICF1 - TOIE0 TOV0 - 24 24 24 25 SRE SRW SE SM ISC11 ISC10 ISC01 ISC00 26 - - - CS02 CS01 CS00 29 30 CTC1 CS12 PWM11 CS11 PWM10 CS10 32 33 34 34 35 35 35 35 Timer/Counter0 (8 Bit) COM1A1 COM1A0 COM1B1 COM1B0 ICNC1 ICES1 Timer/Counter1 - Counter Register High Byte Timer/Counter1 - Counter Register Low Byte Timer/Counter1 - Output Compare Register A High Byte Timer/Counter1 - Output Compare Register A Low Byte Timer/Counter1 - Output Compare Register B High Byte Timer/Counter1 - Output Compare Register B Low Byte Timer/Counter1 - Input Capture Register High Byte Timer/Counter1 - Input Capture Register Low Byte - - - EEPROM Address Register Low Byte EEPROM Data Register PORTA7 PORTA6 PORTA5 DDA7 DDA6 DDA5 PINA7 PINA6 PINA5 PORTB7 PORTB6 PORTB5 DDB7 DDB6 DDB5 PINB7 PINB6 PINB5 PORTC7 PORTC6 PORTC5 DDC7 DDC6 DDC5 PINC7 PINC6 PINC5 PORTD7 PORTD6 PORTD5 DDD7 DDD6 DDD5 PIND7 PIND6 PIND5 SPI Data Register SPIF WCOL SPIE SPE DORD UART I/O Data Register RXC TXC UDRE RXCIE TXCIE UDRIE UART Baud Rate Register ACD ACO AT90S8515 36 36 WDTOE WDE WDP2 WDP1 WDP0 38 - - - - EEAR8 PORTA4 DDA4 PINA4 PORTB4 DDB4 PINB4 PORTC4 DDC4 PINC4 PORTD4 DDD4 PIND4 PORTA3 DDA3 PINA3 PORTB3 DDB3 PINB3 PORTC3 DDC3 PINC3 PORTD3 DDD3 PIND3 EEMWE PORTA2 DDA2 PINA2 PORTB2 DDB2 PINB2 PORTC2 DDC2 PINC2 PORTD2 DDD2 PIND2 EEWE PORTA1 DDA1 PINA1 PORTB1 DDB1 PINB1 PORTC1 DDC1 PINC1 PORTD1 DDD1 PIND1 EERE PORTA0 DDA0 PINA0 PORTB0 DDB0 PINB0 PORTC0 DDC0 PINC0 PORTD0 DDD0 PIND0 MSTR CPOL CPHA SPR1 SPR0 FE RXEN OR TXEN CHR9 RXB8 TXB8 ACI ACIE ACIC ACIS1 ACIS0 39 39 39 40 54 54 54 56 56 56 61 61 61 63 63 63 45 44 44 48 48 49 51 52 AT90S8515 AT90S8515 Instruction Set Summary Mnemonics Operands Description ARITHMETIC AND LOGIC INSTRUCTIONS ADD Rd, Rr Add two Registers ADC Rd, Rr Add with Carry two Registers ADIW Rdl,K Add Immediate to Word SUB Rd, Rr Subtract two Registers SUBI Rd, K Subtract Constant from Register SBC Rd, Rr Subtract with Carry two Registers SBCI Rd, K Subtract with Carry Constant from Reg. SBIW Rdl,K Subtract Immediate from Word AND Rd, Rr Logical AND Registers ANDI Rd, K Logical AND Register and Constant OR Rd, Rr Logical OR Registers ORI Rd, K Logical OR Register and Constant EOR Rd, Rr Exclusive OR Registers COM Rd One’s Complement NEG Rd Two’s Complement SBR Rd,K Set Bit(s) in Register CBR Rd,K Clear Bit(s) in Register INC Rd Increment DEC Rd Decrement TST Rd Test for Zero or Minus CLR Rd Clear Register SER Rd Set Register BRANCH INSTRUCTIONS RJMP k Relative Jump IJMP Indirect Jump to (Z) RCALL k Relative Subroutine Call ICALL Indirect Call to (Z) RET Subroutine Return RETI Interrupt Return CPSE Rd,Rr Compare, Skip if Equal CP Rd,Rr Compare CPC Rd,Rr Compare with Carry CPI Rd,K Compare Register with Immediate SBRC Rr, b Skip if Bit in Register Cleared SBRS Rr, b Skip if Bit in Register is Set SBIC P, b Skip if Bit in I/O Register Cleared SBIS P, b Skip if Bit in I/O Register is Set BRBS s, k Branch if Status Flag Set BRBC s, k Branch if Status Flag Cleared BREQ k Branch if Equal BRNE k Branch if Not Equal BRCS k Branch if Carry Set BRCC k Branch if Carry Cleared BRSH k Branch if Same or Higher BRLO k Branch if Lower BRMI k Branch if Minus BRPL k Branch if Plus BRGE k Branch if Greater or Equal, Signed BRLT k Branch if Less Than Zero, Signed BRHS k Branch if Half Carry Flag Set BRHC k Branch if Half Carry Flag Cleared BRTS k Branch if T Flag Set BRTC k Branch if T Flag Cleared BRVS k Branch if Overflow Flag is Set BRVC k Branch if Overflow Flag is Cleared BRIE k Branch if Interrupt Enabled BRID k Branch if Interrupt Disabled Operation Flags #Clocks Rd ← Rd + Rr Rd ← Rd + Rr + C Rdh:Rdl ← Rdh:Rdl + K Rd ← Rd - Rr Rd ← Rd - K Rd ← Rd - Rr - C Rd ← Rd - K - C Rdh:Rdl ← Rdh:Rdl - K Rd ← Rd • Rr Rd ← Rd • K Rd ← Rd v Rr Rd ← Rd v K Rd ← Rd ⊕ Rr Rd ← $FF − Rd Rd ← $00 − Rd Rd ← Rd v K Rd ← Rd • ($FF - K) Rd ← Rd + 1 Rd ← Rd − 1 Rd ← Rd • Rd Rd ← Rd ⊕ Rd Rd ← $FF Z,C,N,V,H Z,C,N,V,H Z,C,N,V,S Z,C,N,V,H Z,C,N,V,H Z,C,N,V,H Z,C,N,V,H Z,C,N,V,S Z,N,V Z,N,V Z,N,V Z,N,V Z,N,V Z,C,N,V Z,C,N,V,H Z,N,V Z,N,V Z,N,V Z,N,V Z,N,V Z,N,V None 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 PC ← PC + k + 1 PC ← Z PC ← PC + k + 1 PC ← Z PC ← STACK PC ← STACK if (Rd = Rr) PC ← PC + 2 or 3 Rd − Rr Rd − Rr − C Rd − K if (Rr(b)=0) PC ← PC + 2 or 3 if (Rr(b)=1) PC ← PC + 2 or 3 if (P(b)=0) PC ← PC + 2 or 3 if (P(b)=1) PC ← PC + 2 or 3 if (SREG(s) = 1) then PC←PC+k + 1 if (SREG(s) = 0) then PC←PC+k + 1 if (Z = 1) then PC ← PC + k + 1 if (Z = 0) then PC ← PC + k + 1 if (C = 1) then PC ← PC + k + 1 if (C = 0) then PC ← PC + k + 1 if (C = 0) then PC ← PC + k + 1 if (C = 1) then PC ← PC + k + 1 if (N = 1) then PC ← PC + k + 1 if (N = 0) then PC ← PC + k + 1 if (N ⊕ V= 0) then PC ← PC + k + 1 if (N ⊕ V= 1) then PC ← PC + k + 1 if (H = 1) then PC ← PC + k + 1 if (H = 0) then PC ← PC + k + 1 if (T = 1) then PC ← PC + k + 1 if (T = 0) then PC ← PC + k + 1 if (V = 1) then PC ← PC + k + 1 if (V = 0) then PC ← PC + k + 1 if ( I = 1) then PC ← PC + k + 1 if ( I = 0) then PC ← PC + k + 1 None None None None None I None Z, N,V,C,H Z, N,V,C,H Z, N,V,C,H None None None None None None None None None None None None None None None None None None None None None None None None 2 2 3 3 4 4 1/2 1 1 1 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 7 AT90S8515 Instruction Set Summary Mnemonics Operands DATA TRANSFER INSTRUCTIONS MOV Rd, Rr LDI Rd, K LD Rd, X LD Rd, X+ LD Rd, - X LD Rd, Y LD Rd, Y+ LD Rd, - Y LDD Rd,Y+q LD Rd, Z LD Rd, Z+ LD Rd, -Z LDD Rd, Z+q LDS Rd, k ST X, Rr ST X+, Rr ST - X, Rr ST Y, Rr ST Y+, Rr ST - Y, Rr STD Y+q,Rr ST Z, Rr ST Z+, Rr ST -Z, Rr STD Z+q,Rr STS k, Rr LPM IN Rd, P OUT P, Rr PUSH Rr POP Rd BIT AND BIT-TEST INSTRUCTIONS SBI P,b CBI P,b LSL Rd LSR Rd ROL Rd ROR Rd ASR Rd SWAP Rd BSET s BCLR s BST Rr, b BLD Rd, b SEC CLC SEN CLN SEZ CLZ SEI CLI SES CLS SEV CLV SET CLT SEH CLH NOP SLEEP WDR 8 Description Operation Flags #Clocks Move Between Registers Load Immediate Load Indirect Load Indirect and Post-Inc. Load Indirect and Pre-Dec. Load Indirect Load Indirect and Post-Inc. Load Indirect and Pre-Dec. Load Indirect with Displacement Load Indirect Load Indirect and Post-Inc. Load Indirect and Pre-Dec. Load Indirect with Displacement Load Direct from SRAM Store Indirect Store Indirect and Post-Inc. Store Indirect and Pre-Dec. Store Indirect Store Indirect and Post-Inc. Store Indirect and Pre-Dec. Store Indirect with Displacement Store Indirect Store Indirect and Post-Inc. Store Indirect and Pre-Dec. Store Indirect with Displacement Store Direct to SRAM Load Program Memory In Port Out Port Push Register on Stack Pop Register from Stack Rd ← Rr Rd ← K Rd ← (X) Rd ← (X), X ← X + 1 X ← X - 1, Rd ← (X) Rd ← (Y) Rd ← (Y), Y ← Y + 1 Y ← Y - 1, Rd ← (Y) Rd ← (Y + q) Rd ← (Z) Rd ← (Z), Z ← Z+1 Z ← Z - 1, Rd ← (Z) Rd ← (Z + q) Rd ← (k) (X) ← Rr (X) ← Rr, X ← X + 1 X ← X - 1, (X) ← Rr (Y) ← Rr (Y) ← Rr, Y ← Y + 1 Y ← Y - 1, (Y) ← Rr (Y + q) ← Rr (Z) ← Rr (Z) ← Rr, Z ← Z + 1 Z ← Z - 1, (Z) ← Rr (Z + q) ← Rr (k) ← Rr R0 ← (Z) Rd ← P P ← Rr STACK ← Rr Rd ← STACK None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 1 1 2 2 Set Bit in I/O Register Clear Bit in I/O Register Logical Shift Left Logical Shift Right Rotate Left Through Carry Rotate Right Through Carry Arithmetic Shift Right Swap Nibbles Flag Set Flag Clear Bit Store from Register to T Bit load from T to Register Set Carry Clear Carry Set Negative Flag Clear Negative Flag Set Zero Flag Clear Zero Flag Global Interrupt Enable Global Interrupt Disable Set Signed Test Flag Clear Signed Test Flag Set Twos Complement Overflow. Clear Twos Complement Overflow Set T in SREG Clear T in SREG Set Half Carry Flag in SREG Clear Half Carry Flag in SREG No Operation Sleep Watchdog Reset I/O(P,b) ← 1 I/O(P,b) ← 0 Rd(n+1) ← Rd(n), Rd(0) ← 0 Rd(n) ← Rd(n+1), Rd(7) ← 0 Rd(0)←C,Rd(n+1)← Rd(n),C←Rd(7) Rd(7)←C,Rd(n)← Rd(n+1),C←Rd(0) Rd(n) ← Rd(n+1), n=0..6 Rd(3..0)←Rd(7..4),Rd(7..4)←Rd(3..0) SREG(s) ← 1 SREG(s) ← 0 T ← Rr(b) Rd(b) ← T C←1 C←0 N←1 N←0 Z←1 Z←0 I←1 I←0 S←1 S←0 V←1 V←0 T←1 T←0 H←1 H←0 None None Z,C,N,V Z,C,N,V Z,C,N,V Z,C,N,V Z,C,N,V None SREG(s) SREG(s) T None C C N N Z Z I I S S V V T T H H None None None 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 1 AT90S8515 (see specific descr. for Sleep function) (see specific descr. for WDR/timer)