Designed and Manufactured in Germany Specification Oscillator type: Rev.: 1 Date: 2016-07-04 AXDO9000 Very High Stability Ultra-Low Noise Reference (D)OCXO with integrated distribution amplifier with 4 to 16 outputs Features: Very High Frequency Stability Ultra-Low Phase Noise Very Low Aging 4 to 16 isolated outputs for frequency distribution Slim 19” rack with 1 HU For ultimate frequency stability see our GPS-disciplined OCXO AXGPS9000 and our Rubidium Reference AXRB9000 Models: Item (D)OCXO (D)OCXO with integrated Distribution amplifiers GPS-disciplined OCXO Rubidium Model Features AXIOM9000 DOCXO option Ultra-low noise Very high stability Can be combined with AXDA9000 up to 48 outputs See separate data sheet AXDO9000 Stability as AXIOM9000 plus low noise high isolation frequency distribution amplifier with 4 to 16 outputs AXGPS9000 Low noise -11 Stability 10 Distribution option AXRB9000 Excellent long-term stability Distribution option Performance GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany See specification AXDO9000 Rev.1 Drawing D0 Page 1(5) Consult factory www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Parameter min. Nominal output frequency Frequency stability Stability options (Note 2) Initial tolerance at delivery vs. operating temperature range Long term (aging) per day st Long term (aging) 1 year Frequency adjustment range Mechanical Frequency Control RF output RF output ports Signal waveform Load RL Output level per port Isolation between channels Harmonics Spurious Phase noise (Note 2) Short-tem stability (ADEV) (Note 2) Warm-up time (Note 4) AC Supply voltage VS AC Supply input frequency Power consumption Operating temperature range max. 10.000 OCXO < ±10 < ±2 < ±0.5 < ±50 DOCXO < ±10 < ±0.1 < ±0.1 < ±20 > ±0.4 typ. max. 4, 8, 16 Sine wave 50 +16 +14 100 -50 -90 100 50 -10 Unit Condition MHz > ±0.8 min. Enclosure (see drawing) (WxDxH) RF Connectors Weight Notes: 1. 2. 3. 4. typ. See table 1 -12 -12 2·10 5·10 5 230 240 60 20 +60 483x250x44 BNC female 4 ppb ppb ppb ppb Option 1 @ +25°C steady state after 30 days operation after 30 days operation ppm By trimmer access (Note 3) Option 2 Ω dBm dB dBc dBc ±5% Option 3 @ τ = 1 sec ∆ffinal/f0 < ±0.1 ppm IEC 60320-1 / C14 min V Hz W °C mm @ Rear plate kg Terminology and test conditions are according to IEC60679-1 and MIL-PRF-55310, unless otherwise stated Other stabilities and phase noise on request Trimmer accessible at front plate. Adjustment range sufficient for 15 years operation. Warm-up indicator at front plate. Indicator ON when accuracy within ±500 ppb. Absolute Maximum Ratings Parameter AC Supply Voltage VS AC Supply input frequency AC Supply input current Load RL Storage Temperature min. max. Unit 90 47 260 63 1 ∞ +70 V Hz A Ω °C 0 -20 Condition Fuse accessible at rear plate No damage Ordering Code Option 1 Option 2 [Stability] [Output ports] “SO” – OCXO AXDO9000 4, 8, 16 “DO” – DOCXO Example: AXDO9000-SO-16-LN_Rev.1 – 10.000 MHz Model GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany Option 3 [Phase noise] AXDO9000 Rev.1 Drawing D0 Page 2(5) Table 1 Revision Frequency [MHz] Rev.1 10.000 www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Phase Noise – Option 3: 10 MHz Offset LN -100 -130 -145 -150 -155 -155 1 Hz 10 Hz 100 Hz 1 kHz 10 kHz ≥100 kHz Table 1 ULN* -108 -138 -148 -158 -163 -165 Unit dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz *ULN Ultra-Low Noise option only for Option 1 “SO” Typical Phase Noise Performance “ULN” Option 3 GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXDO9000 Rev.1 Drawing D0 Page 3(5) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Enclosure drawing Connections and operation # 1 2 3 4 5 6 7 Panel Rear Front Symbol POWER IN FUSE OUT POWER SWITCH POWER ON OVEN READY ADJUST Function AC Supply Input (IEC 60320-1 / C14) 1 A Slow 5x20 mm Fuse RF outputs 4…16* Power Switch ON/OFF LED – Power On Indicator LED – Oven Ready Indicator Frequency adjustment potentiometer *Unused outputs must be terminated with 50 Ω loads. Number of outputs depending on Option 2. GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXDO9000 Rev.1 Drawing D0 Page 4(5) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Handling & Testing Parameter Procedure / Test condition Sinusoidal vibration Random vibration Mechanical shock Handling and Testing max. 0.15 mm <10 Hz, 1 g at 10~2000 Hz max. 0.001 g²/Hz, 10~2000 Hz max. 10 g, 11 ms half sine Careful handling. Avoid air flow, fan vibration and shock during operation. Yes No Yes No DGUV Requirement 3 Tested RoHS-Compliant Data sheet is for information purposes only and may be subject to modifications or may be discontinued without notice. Revision History Rev. Drawing Date [dd.mm.yyyy] Remarks Author Checked 1 D0 04.07.2016 First issue HH BN GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXDO9000 Rev.1 Drawing D0 Page 5(5) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected]