SSOUSA AD2C112 Compact 4 pin dip/smd package Datasheet

AD2C112
1 Form B
400V / 35Ω
MOSFET Output Solid State Relay
Description
Features
The AD2C112 is a bi-directional, single-pole, single-throw,
normally closed multipurpose relay. It is designed to
replace electro-mechanical relays in general purpose
switching applications. The relay consists of an integrated
circuit that drives two rugged drain-to-drain depletion type
DMOS transistors - optically coupled to a light emitting
diode. The device comes with up to 5kV input to output
isolation.
Compact 4 pin DIP/SMD Package

High Isolation Voltage (up to 5kVRMS)

Low Input Control Current (2.5mA TYP)

25Ω Typical On Resistance

120mA Maximum Continuous Load Current

Long Life / High Reliability

RoHS / Pb-Free / REACH Compliant
Agency Approvals
The AD2C112 comes standard in a miniature 4 pin DIP
package making it ideal for high-density board applications.
UL/C-UL:
VDE:
Applications

Reed Relay Replacement

Meter Reading Systems

Data Acquisition

Medical Equipment

Battery Monitoring

Safety Systems
File # E201932
File # 40035191 (EN 60747-5-2)
Absolute Maximum Ratings
The values indicated are absolute stress ratings. Functional
operation of the device is not implied at these or any
conditions in excess of those defined in electrical
characteristics section of this document. Exposure to
absolute Maximum Ratings may cause permanent damage
to the device and may adversely affect reliability.
Schematic Diagram
(+) Input

Storage Temperature …………………………..-55 to +125°C
Operating Temperature …………………………-40 to +85°C
Continuous Input Current ………………………………..50mA
Transient Input Current ………………….……………..500mA
Reverse Input Control Voltage …………..…………………5V
Input Power Dissipation …………………………………40mW
Output Power Dissipation ……………………………..500mW
Solder Temperature – Wave (10sec)……………….….260°C
Solder Temperature – IR Reflow (10sec)….…………..260°C
1
4
(+/-) Load
Ordering Information
(-) Input
2
3
AD2C112
(-/+) Load
Part Number
AD2C112
AD2C112-H
AD2C112-S
AD2C112-HS
AD2C112-STR
AD2C112-HSTR
Description
4 pin DIP, (100/Tube)
5kVRMS Viso, 8 pin DIP, (100/Tube)
4 pin SMD, (100/Tube)
5kVRMS, 4 pin SMD, (100/Tube)
4 pin SMD, Tape & Reel (2000/Reel)
5kVRMS, 4 pin SMD, Tape & Reel (2000/Reel)
NOTE: Suffixes listed above are not included in marking on device
for part number identification
© 2014 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 1 of 8
AD2C112 H/S/TR
Rev 2.01 (02/17/2014)
001793
AD2C112
1 Form B
400V / 35Ω
MOSFET Output Solid State Relay
Electrical Characteristics, TA = 25°C (unless otherwise specified)
Parameter
Symbol
Min.
Typ.
Max.
Units
Test Conditions
Input Specifications
LED Forward Voltage
VF
-
1.2
1.5
V
IF=10mA
LED Reverse Voltage
BVR
5
-
-
V
IR=10μA
Turn-On Current
IF
-
0.5
-
mA
IO=120mA
Turn-Off Current
IFOFF
-
2.5
5
mA
IO=120mA
Blocking Voltage
VB
400
-
-
V
IF=5mA, IO=1A
Continuous Load Current
IO
-
-
120
mA
IF=0mA
On Resistance
RON
-
25
35
Ω
IF=0mA, IO=120mA
Leakage Current
IOleak
-
0.2
1
A
IF=5mA, VO=400V
Output Capacitance
COUT
-
20
-
pF
IF=5mA, f=1.0MHz
VOFFSET
-
-
0.2
mV
IF=0mA
Turn-On Time
TON
-
0.3
1
mS
IF=0mA, IO=120mA
Turn-Off Time
TOFF
-
1
5
mS
IF=5mA, IO=120mA
Output Specifications
Offset Voltage
Coupled Specifications
Coupled Capacitance
Contact Transient Ratio
CCOUPLED
-
3
-
pF
-
2,000
7,000
0
V/S
3,750
-
-
5,000
-
-
dV = 50V
Isolation Specifications
Isolation Voltage
(-H Option)
Input-Output Resistance
© 2014 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
VISO
RI-O
-
10
Page 2 of 8
12
-
VRMS
RH ≤ 50%, t=1min

VI-O = 500VDC
AD2C112 H/S/TR
Rev 2.01 (02/17/2014)
001793
AD2C112
1 Form B
400V / 35Ω
MOSFET Output Solid State Relay
AD2C112 Performance & Characteristics Plots, TA = 25°C (unless otherwise specified)
IF=5mA
IO=120mA
IF=0mA
IO=120mA
© 2014 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 3 of 8
AD2C112 H/S/TR
Rev 2.01 (02/17/2014)
001793
AD2C112
1 Form B
400V / 35Ω
MOSFET Output Solid State Relay
AD2C112 Solder Temperature Profile Recommendations
(1) Infrared Reflow:
Refer to the following figure as an example of an optimal temperature profile for single occurrence infrared reflow.
Soldering process should not exceed temperature or time limits expressed herein. Surface temperature of device
package should not exceed 250ºC:
G
F
D
E
H
B
A
C
Figure 1
Process
Step
A
B
C
D
E
F
G
H
Description
Preheat Start Temperature (ºC)
Preheat Finish Temperature (ºC)
Preheat Time (s)
Melting Temperature (ºC)
Time above Melting Temperature (s)
Peak Temperature, at Terminal (ºC)
Dwell Time at Peak Temperature (s)
Cool-down (ºC/s)
Parameter
150ºC
180ºC
90 - 120s
230ºC
30s
260ºC
10s
<6ºC/s
(2) Wave Solder:
Maximum Temperature:
Maximum Time:
Pre-heating:
Single Occurrence
260ºC (at terminal)
10s
100 - 150ºC (30 - 90s)
(3) Hand Solder:
Maximum Temperature:
Maximum Time:
Single Occurrence
© 2014 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
350ºC
3s
(at tip of soldering iron)
Page 4 of 8
AD2C112 H/S/TR
Rev 2.01 (02/17/2014)
001793
AD2C112
1 Form B
400V / 35Ω
MOSFET Output Solid State Relay
AD2C112 Package Dimensions
4 PIN DIP Package
© 2014 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Note:
Page 5 of 8
All dimensions in millimeters with inches [“] in parenthesis ()
AD2C112 H/S/TR
Rev 2.01 (02/17/2014)
001793
AD2C112
1 Form B
400V / 35Ω
MOSFET Output Solid State Relay
AD2C112 Package Dimensions
4 PIN SMD Surface Mount Package (-S)
© 2014 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Note:
Page 6 of 8
All dimensions in millimeters with inches [“] in parenthesis ()
AD2C112 H/S/TR
Rev 2.01 (02/17/2014)
001793
AD2C112
1 Form B
400V / 35Ω
MOSFET Output Solid State Relay
AD2C112 Package Dimensions
4 PIN SMD Tape & Reel (-STR)
Note:
All dimensions in millimeters
F
P0
P1
P2
W
7.5±0.1
4.0±0.1
12.0±0.1
2.0±0.1
16.0±0.3
L
M
N
O
Q
R
S
330±2
101.6±1
16.4+0.2
2.0±0.2
R13±0.5
1.50±0.5
R10±1
© 2014 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 7 of 8
AD2C112 H/S/TR
Rev 2.01 (02/17/2014)
001793
AD2C112
1 Form B
400V / 35Ω
MOSFET Output Solid State Relay
AD2C112 Package Marking
AD2C112 Package Weights
Single Unit
Full Tube
(100pcs)
Full Pouch
(10 tubes)
Full Reel
(2000pcs)
AD2C112-(H)
0.23
39
400
-
AD2C112-(H)S
0.22
38
390
-
0.22
-
-
920
Device
AD2C112-(H)STR
Note:
All weights above are in GRAMS, and include
packaging materials where applicable
DISCLAIMER
Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO
reserves the right to make changes to product description, specifications at any time without further notices.
SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent
licenses nor indemnity are expressed or implied.
Except as specified in SSO’s Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other
warranty, expressed or implied, including merchantability and fitness for particular use.
LIFE SUPPORT POLICY
SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or
death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all
damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the
body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be
reasonably expected to result in significant injury to the user, or (d) a critical component of a life support device or system whose failure can be
reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness.
© 2014 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 8 of 8
AD2C112 H/S/TR
Rev 2.01 (02/17/2014)
001793
Similar pages