AAT3216 150mA MicroPower™ LDO with PowerOK General Description Features The AAT3216 MicroPower™ Low Dropout Linear Regulator is ideally suited for portable applications where low noise, extended battery life and small size are critical. The AAT3216 has been specifically designed for low output noise performance, fast transient response and high power supply rejection ratio (PSRR), making it ideal for powering sensitive RF circuits. • • • • • • • • • • • • • • • Low Dropout - 200mV at 150mA Guaranteed 150mA Output High accuracy ±1.5% 70µA Quiescent Current High Power Supply Ripple Rejection Low self noise PowerOK (POK) Output Fast line and load transient response Short circuit protection Over-Temperature protection Uses Low ESR ceramic capacitors Shutdown mode for longer battery life Low temperature coefficient 12 Factory programmed output voltages SOT23 5-pin or SC70-JW 8-pin package Preliminary Information Other features include low quiescent current, typically 70µA, and low dropout voltage which is typically less than 200mV at full output current. The device is output short circuit protected and has a thermal shutdown circuit for additional protection under extreme conditions. PowerLinear™™ SmartSwitch The AAT3216 also features a low-power shutdown mode for extended battery life. A Power-OK opendrain output signals when VOUT is in regulation. The AAT3216 is available in a space saving 5-pin SOT23 or 8-pin SC70-JW package in 12 factory programmed voltages of 1.2V, 1.5V, 1.8V, 2.0V, 2.3V, 2.5V, 2.7V, 2.8V, 2.85, 3.0V, 3.3V, or 3.5V. Applications • • • • • • Cellular Phones Notebook Computers Desktop Computers Portable Communication Devices Personal Portable Electronics Digital Cameras Typical Application VIN VOUT IN OUT AAT3216 ON/OFF EN 100k POK POK GND 1µF GND 3216.2004.01.0.94 2.2µF GND 1 AAT3216 150mA MicroPower™ LDO with PowerOK Pin Descriptions Pin # Symbol Function SOT23-5 SC70JW-8 1 5, 6 IN 2 8 GND 3 7 EN Enable pin - this pin should not be left floating. When pulled low the PMOS pass transistor turns off and all internal circuitry enters low-power mode, consuming less than 1µA. 4 1 POK Power-OK Output. This open-drain output is low when OUT is out of regulation. Connect a pull up resistor from POK to OUT or IN. 5 2, 3, 4 OUT Output pin - should be decoupled with 2.2µF ceramic capacitor. Input voltage pin - should be decoupled with 1µF or greater capacitor. Ground connection pin Pin Configuration SOT23-5 (Top View) OUT POK POK OUT OUT OUT 1 8 7 2 2 2 1 5 2 3 4 1 IN GND EN SC70JW-8 (Top View) 3 6 4 5 GND EN IN IN 3216.2004.01.0.94 AAT3216 150mA MicroPower™ LDO with PowerOK Absolute Maximum Ratings (TA=25°C unless otherwise noted) Symbol Description VIN, POK IOUT TJ Input Voltage, POK DC Output Current Operating Junction Temperature Range Value Units 6 PD/(VIN-VO) -40 to 150 V mA °C Note: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum rating should be applied at any one time. Thermal Information Symbol ΘJA PD Description Maximum Thermal Resistance (SOT23-5, SC70JW-8) Maximum Power Dissipation1 (SOT23-5, SC70JW-8) 1 Rating Units 190 526 °C/W mW Note 1: Mounted on a demo board. Recommended Operating Conditions Symbol VIN T Description Input Voltage Ambient Temperature Range 2 Rating Units (VOUT + VDO) to 5.5 -40 to +85 V °C Note 2: To calculate minimum input voltage, use the following equation: VIN(MIN) = VOUT(MAX) + VDO(MAX) as long as VIN ≥ 2.5V. 3216.2004.01.0.94 3 AAT3216 150mA MicroPower™ LDO with PowerOK Electrical Characteristics (VIN=VOUT(NOM)+1V for VOUT options greater than 1.5V. VIN= 2.5 for VOUT≤1.5V. IOUT=1mA, COUT=2.2µF, CIN=1µf, TA= -40 to 85°C unless otherwise noted. Typical values are at TA=25°C) Symbol Description Conditions Output Voltage Tolerance IOUT = 1mA to 150mA Output Current Dropout Voltage 1, 2 Short Circuit Current Ground Current Shutdown Current VOUT > 1.2V IOUT = 150mA VOUT < 0.4V VIN = 5V, No load, EN = VIN VIN = 5V, EN = 0V Line Regulation 3 VIN = VOUT + 1 to 5.0V ∆VOUT(line) Dynamic Line Regulation ∆VOUT(load) VEN(L) VEN(H) IEN VPOK VPOKHYS VPOK(OL) IPOK Dynamic Load Regulation Enable Threshold Low Enable Threshold High Leakage Current on Enable Pin POK Trip Threshold POK Hysteresis POK Output Voltage Low POK Output Leakage Current VIN=VOUT+1V to VOUT+2V, IOUT=150mA, TR/TF =2µs IOUT = 1mA to 150mA, TR<5µs VOUT IOUT VDO ISC IQ ISD ∆VOUT/VOUT*∆VIN PSRR TSD THYS eN TC Power Supply Rejection Ratio Min Typ Max TA=25°C -1.5 TA=-40 to 85°C -2.5 150 1.5 2.5 200 600 70 125 1 % % mA mV mA µA µA 0.09 %/V 300 5 mV 30 mV V V µA % of VOUT % of VOUT V µA 0.6 1.5 VEN = 5V VOUT rising, TA = 25°C ISINK = 1mA VPOK < 5.5V, VOUT in regulation 1 kHz IOUT=10mA 10kHz 1MHz Over Temp Shutdown Threshold Over Temp Shutdown Hysteresis Output Noise Noise Power BW = 300Hz-50kHz Output Voltage Temp. Coeff. 90 Units 94 1 1 98 0.4 1 65 45 42 145 12 250 22 dB °C °C µVrms/rtHz ppm/°C Note 1: VDO is defined as VIN - VOUT when VOUT is 98% of nominal. Note 2: For VOUT < 2.3V, VDO = 2.5V - VOUT. Note 3: CIN = 10µF 4 3216.2004.01.0.94 AAT3216 150mA MicroPower™ LDO with PowerOK Typical Characteristics (Unless otherwise noted, VIN = 5V, TA = 25°C) Dropout Characteristics Dropout Voltage vs. Temperature 260 240 220 200 180 160 140 120 100 80 60 40 20 0 3.00 IL = 150mA IOUT = 0mA 2.80 V OUT (V) Dropout Voltage (mV) 3.20 IL = 100mA IOUT = 10mA 2.60 IOUT = 50mA 2.40 IL = 50mA -40 -30 -20 -10 0 IOUT = 100mA IOUT = 150mA 2.20 2.00 2.70 10 20 30 40 50 60 70 80 90 100 110 120 2.80 2.90 3.00 3.10 3.20 VIN (V) Temperature (°C) Ground Current vs. Input Voltage Dropout Voltage vs. Output Current 90.00 80.00 250 70.00 200 IGND (µA) Dropout Voltage (mV) 300 85°C 150 100 50.00 IOUT=150mA 40.00 IOUT=10mA 20.00 -40°C IOUT=50mA IOUT=0mA 30.00 25°C 50 60.00 10.00 0 0 25 50 75 100 125 0.00 150 2 2.5 3 4 4.5 5 Output Voltage vs. Temperature Quiescent Current vs. Temperature 1.203 100 90 1.202 80 Output Voltage (V) Quiescent Current (µA) 3.5 VIN (V) Output Current (mA) 70 60 50 40 30 20 10 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 Temperature (°C) 3216.2004.01.0.94 1.201 1.200 1.199 1.198 1.197 1.196 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 Temperature (°C) 5 AAT3216 150mA MicroPower™ LDO with PowerOK Typical Characteristics (Unless otherwise noted, VIN = 5V, TA = 25°C) Turn Off Time with POK Delay Turn On Time and POK Delay VENABLE (2V/div) VEN (2V/div) VOUT (500mV/div) VPOK (2V/div) VPOK (500mV/div) VOUT (2V/div) Time (200µs/div) Time (10µs/div) Line Transient Response Load Transient Response 2.90 6 VIN 3.10 2 3.05 1 3.00 VOUT 2.95 -1 2.90 -2 2.85 400 VOUT 2.80 300 2.75 200 2.70 100 2.65 IOUT (mA) 3.15 3 V OUT (V) 4 0 2.85 3.20 V OUT (V) 5 V IN (V) 500 3.25 0 IOUT 2.60 -100 100 µs/div Time (100 µs/div) Over Current Protection POK Output Response 1200 VIN (2V/div) 1000 IOUT (mA) 800 VOUT (2V/div) 600 400 200 0 VPOK (1V/div) -200 Time (20 ms/div) 6 Time (200µs/div.) 3216.2004.01.0.94 AAT3216 150mA MicroPower™ LDO with PowerOK Typical Characteristics (Unless otherwise noted, VIN = 5V, TA = 25°C) VEN(H) and V EN(L) vs. VIN 10 1.250 1.225 1.200 1 VEN (V) Noise Amplitude (µV/rtHz) AAT3216 Self Noise 0.1 1.175 VEN(H) 1.150 1.125 VEN(L) 1.100 1.075 0.01 0.01 0.1 1 10 Frequency (kHz) 3216.2004.01.0.94 100 1000 1.050 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VIN (V) 7 AAT3216 150mA MicroPower™ LDO with PowerOK Functional Block Diagram IN OUT Over-Current Protection Over-Temperature Protection Error Amplifier EN POK Voltage Reference 94% GND Functional Description The AAT3216 is intended for LDO regulator applications where output current load requirements range from no load to 150mA. The advanced circuit design of the AAT3216 provides excellent transient response and fast turn-on ability. The LDO regulator output has been specifically optimized to function with low cost, low ESR ceramic capacitors. However, the design will allow for operation over a wide range of capacitor types. The AAT3216 has an integrated Power-OK comparator which indicates when the output is out of regulation. 8 The device enable circuit is provided to shutdown the LDO regulator for power conservation in portable products. The enable circuit has an additional output capacitor discharge circuit to assure sharp application circuit turn off upon device shutdown. This LDO regulator has complete short circuit and thermal protection. The integral combination of these two internal protection circuits give the AAT3216 a comprehensive safety system during extreme adverse operating conditions. Device power dissipation is limited to the package type and thermal dissipation properties. Refer to the thermal considerations discussion in the section for details on device operation at maximum output current loads. 3216.2004.01.0.94 AAT3216 150mA MicroPower™ LDO with PowerOK Applications Information To assure the maximum possible performance is obtained from the AAT3216, please refer to the following application recommendations. Input Capacitor Typically a 1µF or larger capacitor is recommended for CIN in most applications. A CIN capacitor is not required for basic LDO regulator operation. However, if the AAT3216 is physically located more than 3 centimeters from an input power source, a CIN capacitor will be needed for stable operation. CIN should be located as close to the device VIN pin as practically possible. CIN values greater than 1µF will offer superior input line transient response and will assist in maximizing the highest possible power supply ripple rejection. Ceramic, tantalum or aluminum electrolytic capacitors may be selected for CIN. There is no specific capacitor ESR requirement for CIN. However, for 150mA LDO regulator output operation, ceramic capacitors are recommended for CIN due to their inherent capability over tantalum capacitors to withstand input current surges from low impedance sources such as batteries in portable devices. Output Capacitor For proper load voltage regulation and operational stability, a capacitor is required between pins VOUT and GND. The COUT capacitor connection to the LDO regulator ground pin should be made as direct as practically possible for maximum device performance. The AAT3216 has been specifically designed to function with very low ESR ceramic capacitors. For best performance, ceramic capacitors are recommended. Typical output capacitor values for maximum output current conditions range from 1µF to 10µF. Applications utilizing the exceptionally low output noise and optimum power supply ripple rejection characteristics of the AAT3216 should use 2.2µF or greater for COUT. If desired, COUT may be increased without limit. In low output current applications where output load is less then 10mA, the minimum value for COUT can be as low as 0.47µF. 3216.2004.01.0.94 Capacitor Characteristics Ceramic composition capacitors are highly recommended over all other types of capacitors for use with the AAT3216. Ceramic capacitors offer many advantages over their tantalum and aluminum electrolytic counterparts. A ceramic capacitor typically has very low ESR, is lower cost, has a smaller PCB footprint and is non-polarized. Line and load transient response of the LDO regulator is improved by using low ESR ceramic capacitors. Since ceramic capacitors are non-polarized, they are not prone to incorrect connection damage. Equivalent Series Resistance (ESR): ESR is a very important characteristic to consider when selecting a capacitor. ESR is the internal series resistance associated with a capacitor, which includes lead resistance, internal connections, size and area, material composition and ambient temperature. Typically capacitor ESR is measured in milliohms for ceramic capacitors and can range to more than several ohms for tantalum or aluminum electrolytic capacitors. Ceramic Capacitor Materials: Ceramic capacitors less than 0.1µF are typically made from NPO or COG materials. NPO and COG materials are typically tight tolerance very stable over temperature. Larger capacitor values are typically composed of X7R, X5R, Z5U and Y5V dielectric materials. Large ceramic capacitors, typically greater then 2.2µF are often available in the low cost Y5V and Z5U dielectrics. These two material types are not recommended for use with LDO regulators since the capacitor tolerance can vary more than ±50% over the operating temperature range of the device. A 2.2µF Y5V capacitor could be reduced to 1µF over temperature, this could cause problems for circuit operation. X7R and X5R dielectrics are much more desirable. The temperature tolerance of X7R dielectric is better than ±15%. Capacitor area is another contributor to ESR. Capacitors which are physically large in size will have a lower ESR when compared to a smaller sized capacitor of an equivalent material and capacitance value. These larger devices can improve circuit transient response when compared to an equal value capacitor in a smaller package size. 9 AAT3216 150mA MicroPower™ LDO with PowerOK Applications Information Consult capacitor vendor data sheets carefully when selecting capacitors for LDO regulators. POK Output The AAT 3216 features an integrated Power-OK comparator which can be used as an error flag. The POK open-drain output goes low when OUT is 6% below its nominal regulation voltage. Connect a pull-up resistor from POK to OUT or IN. A delayed POK signal can be implemented with a capacitor in parallel with the pull-up resistor. Enable Function The AAT3216 features an LDO regulator enable/ disable function. This pin (EN) is active high and is compatible with CMOS logic. To assure the LDO regulator will switch on, the EN turn on control level must be greater than 2.0 volts. The LDO regulator will go into the disable shutdown mode when the voltage on the EN pin falls below 0.6 volts. If the enable function is not needed in a specific application, it may be tied to VIN to keep the LDO regulator in a continuously on state. When the LDO regulator is in the shutdown mode, an internal 1.5kΩ resistor is connected between VOUT and GND. This is intended to discharge COUT when the LDO regulator is disabled. The internal 1.5kΩ has no adverse effect on device turn on time. Short Circuit Protection The AAT3216 contains an internal short circuit protection circuit that will trigger when the output load current exceeds the internal threshold limit. Under short circuit conditions the output of the LDO regulator will be current limited until the short circuit condition is removed from the output or LDO regulator package power dissipation exceeds the device thermal limit. Thermal Protection The AAT3216 has an internal thermal protection circuit which will turn on when the device die temperature exceeds 150°C. The internal thermal protection circuit will actively turn off the LDO regulator 10 output pass device to prevent the possibility of over temperature damage. The LDO regulator output will remain in a shutdown state until the internal die temperature falls back below the 150°C trip point. The combination and interaction between the short circuit and thermal protection systems allow the LDO regulator to withstand indefinite short circuit conditions without sustaining permanent damage. No-Load Stability The AAT3216 is designed to maintain output voltage regulation and stability under operational noload conditions. This is an important characteristic for applications where the output current may drop to zero. Reverse Output to Input Voltage Conditions and Protection Under normal operating conditions a parasitic diode exists between the output and input of the LDO regulator. The input voltage should always remain greater then the output load voltage maintaining a reverse bias on the internal parasitic diode. Conditions where VOUT might exceed VIN should be avoided since this would forward bias the internal parasitic diode and allow excessive current flow into the VOUT pin possibly damaging the LDO regulator. In applications where there is a possibility of VOUT exceeding VIN for brief amounts of time during normal operation, the use of a larger value CIN capacitor is highly recommended. A larger value of CIN with respect to COUT will effect a slower CIN decay rate during shutdown, thus preventing VOUT from exceeding VIN. In applications where there is a greater danger of VOUT exceeding VIN for extended periods of time, it is recommended to place a schottky diode across VIN to VOUT (connecting the cathode to VIN and anode to VOUT). The Schottky diode forward voltage should be less than 0.45 volts. Thermal Considerations and High Output Current Applications The AAT3216 is designed to deliver a continuous output load current of 150mA under normal operating conditions. 3216.2004.01.0.94 AAT3216 150mA MicroPower™ LDO with PowerOK Applications Information This formula can be solved for VIN to determine the maximum input voltage. The limiting characteristic for the maximum output load current safe operating area is essentially package power dissipation and the internal preset thermal limit of the device. In order to obtain high operating currents, careful device layout and circuit operating conditions need to be taken into account. The following is an example for an AAT3216 set for a 2.5 volt output: The following discussions will assume the LDO regulator is mounted on a printed circuit board utilizing the minimum recommended footprint as stated in the layout considerations section of the document. VOUT = 2.5 volts IOUT = 150mA IGND = 150µA At any given ambient temperature (TA) the maximum package power dissipation can be determined by the following equation: PD(MAX) = [TJ(MAX) - TA] / ΘJA Constants for the AAT3216 are TJ(MAX), the maximum junction temperature for the device which is 125°C and ΘJA = 190°C/W, the package thermal resistance. Typically, maximum conditions are calculated at the maximum operating temperature where TA = 85°C, under normal ambient conditions TA = 25°C. Given TA = 85°, the maximum package power dissipation is 211mW. At TA = 25°C°, the maximum package power dissipation is 526mW. The maximum continuous output current for the AAT3216 is a function of the package power dissipation and the input to output voltage drop across the LDO regulator. Refer to the following simple equation: IOUT(MAX) < PD(MAX) / (VIN - VOUT) For example, if VIN = 5V, VOUT = 3V and TA = 25°, IOUT(MAX) < 264mA. If the output load current were to exceed 264mA or if the ambient temperature were to increase, the internal die temperature will increase. If the condition remained constant, the LDO regulator thermal protection circuit will activate. To figure what the maximum input voltage would be for a given load current refer to the following equation. This calculation accounts for the total power dissipation of the LDO Regulator, including that caused by ground current. PD(MAX) = (VIN - VOUT)IOUT + (VIN x IGND) 3216.2004.01.0.94 VIN(MAX) = (PD(MAX) + (VOUT x IOUT)) / (IOUT + IGND) From the discussion above, PD(MAX) was determined to equal 526mW at TA = 25°C. VIN(MAX)=(526mW+(2.5Vx150mA))/(150mA +150µA) VIN(MAX) = 6.00V Thus, the AAT3216 can sustain a constant 2.5V output at a 150mA load current as long as VIN is ≤ 6.00V at an ambient temperature of 25°C. 6.0V is the absolute maximum voltage where an AAT3216 would never be operated, thus at 25°C, the device would not have any thermal concerns or operational VIN(MAX) limits. This situation can be different at 85°C. The following is an example for an AAT3216 set for a 2.5 volt output at 85°C: From the discussion above, PD(MAX) was determined to equal 211mW at TA = 85°C. VOUT = 2.5 volts IOUT = 150mA IGND = 150uA VIN(MAX)=(211mW+(2.5Vx150mA))/(150mA +150uA) VIN(MAX) = 3.90V Higher input to output voltage differentials can be obtained with the AAT3216, while maintaining device functions within the thermal safe operating area. To accomplish this, the device thermal resistance must be reduced by increasing the heat sink area or by operating the LDO regulator in a duty cycled mode. For example, an application requires VIN = 4.2V while VOUT = 2.5V at a 150mA load and TA = 85°C. VIN is greater than 3.90V, which is the maximum safe continuous input level for VOUT = 2.5V at 150mA for TA = 85°C. To maintain this high input voltage and output current level, the LDO regulator 11 AAT3216 150mA MicroPower™ LDO with PowerOK must be operated in a duty cycled mode. Refer to the following calculation for duty cycle operation: Device Duty Cycle vs. V DROP VOUT = 2.5V @ 25 C PD(MAX) is assumed to be 211mW VOUT = 2.5 volt %DC=100(PD(MAX)/((VIN-VOUT)IOUT+(VINxIGND)) 3.5 Voltage Drop (V) IGND = 150µA IOUT = 150mA VIN = 4.2 volts %DC=100(211mW/((4.2V-2.5V)150mA+(4.2Vx150µA)) 3 2.5 200mA 2 1.5 1 0.5 0 0 %DC = 85.54% 10 20 30 40 50 60 70 80 90 100 Duty Cycle (%) For a 150mA output current and a 2.7volt drop across the AAT3216 at an ambient temperature of 85°C, the maximum on time duty cycle for the device would be 85.54%. Device Duty Cycle vs. VDROP VOUT= 2.5V @ 50 C The following family of curves show the safe operating area for duty cycled operation from ambient room temperature to the maximum operating level. Voltage Drop (V) 3.5 3 2.5 200mA 2 150mA 1.5 1 0.5 0 0 10 20 30 40 50 60 70 80 90 100 Duty Cycle (%) Device Duty Cycle vs. VDROP VOUT = 2.5V @ 85 C Voltage Drop (V) 3.5 100mA 3 2.5 200mA 2 1.5 150mA 1 0.5 0 0 10 20 30 40 50 60 70 80 90 100 Duty Cycle (%) 12 3216.2004.01.0.94 AAT3216 150mA MicroPower™ LDO with PowerOK Applications Information High Peak Output Current Applications Some applications require the LDO regulator to operate at continuous nominal level with short duration high current peaks. The duty cycles for both output current levels must be taken into account. To do so, one would first need to calculate the power dissipation at the nominal continuous level, then factor in the additional power dissipation due to the short duration high current peaks. For example, a 2.5V system using a AAT3216IGV2.5-T1 operates at a continuous 100mA load current level and has short 150mA current peaks. The current peak occurs for 378µs out of a 4.61ms period. It will be assumed the input voltage is 4.2V. First the current duty cycle in percent must be calculated: % Peak Duty Cycle: X/100 = 378µs/4.61ms % Peak Duty Cycle = 8.2% The LDO Regulator will be under the 100mA load for 91.8% of the 4.61ms period and have 150mA peaks occurring for 8.2% of the time. Next, the continuous nominal power dissipation for the 100mA load should be determined then multiplied by the duty cycle to conclude the actual power dissipation over time. 3216.2004.01.0.94 PD(MAX) = (VIN - VOUT)IOUT + (VIN x IGND) PD(100mA) = (4.2V - 2.5V)100mA + (4.2V x 150µA) PD(100mA) = 170.6mW PD(91.8%D/C) = %DC x PD(100mA) PD(91.8%D/C) = 0.918 x 170.6mW PD(91.8%D/C) = 156.6mW The power dissipation for 100mA load occurring for 91.8% of the duty cycle will be 156.6mW. Now the power dissipation for the remaining 8.2% of the duty cycle at the 150mA load can be calculated: PD(MAX) = (VIN - VOUT)IOUT + (VIN x IGND) PD(150mA) = (4.2V - 2.5V)150mA + (4.2V x 150mA) PD(150mA) = 255.6mW PD(8.2%D/C) = %DC x PD(150mA) PD(8.2%D/C) = 0.082 x 255.6mW PD(8.2%D/C) = 21mW The power dissipation for 150mA load occurring for 8.2% of the duty cycle will be 21mW. Finally, the two power dissipation levels can summed to determine the total true power dissipation under the varied load. PD(total) = PD(100mA) + PD(150mA) PD(total) = 156.6mW + 21mW PD(total) = 177.6mW The maximum power dissipation for the AAT3216 operating at an ambient temperature of 85°C is 211mW. The device in this example will have a total power dissipation of 177.6mW. This is well within the thermal limits for safe operation of the device. 13 AAT3216 150mA MicroPower™ LDO with PowerOK Ordering Information Output Voltage Package Marking1 Part Number (Tape and Reel) 1.2V SOT23-5 EAXYY AAT3216IGV-1.2-T1 1.5V SOT23-5 KJXYY AAT3216IGV-1.5-T1 1.8V SOT23-5 AAT3216IGV-1.8-T1 2.0V SOT23-5 AAT3216IGV-2.0-T1 2.3V SOT23-5 AAT3216IGV-2.3-T1 2.5V SOT23-5 2.7V SOT23-5 2.8V SOT23-5 ELXYY AAT3216IGV-2.8-T1 2.85V SOT23-5 FSXYY AAT3216IGV-2.85-T1 3.0V SOT23-5 3.3V SOT23-5 HQXYY AAT3216IGV-3.3-T1 3.5V SOT23-5 IYXYY AAT3216IGV-3.5-T1 1.2V SC70JW-8 AAT3216IJS-1.2-T1 1.5V SC70JW-8 AAT3216IJS-1.5-T1 1.8V SC70JW-8 AAT3216IJS-1.8-T1 2.0V SC70JW-8 AAT3216IJS-2.0-T1 2.3V SC70JW-8 AAT3216IJS-2.3-T1 2.5V SC70JW-8 AAT3216IJS-2.5-T1 2.7V SC70JW-8 AAT3216IJS-2.7-T1 2.8V SC70JW-8 AAT3216IJS-2.8-T1 2.85V SC70JW-8 AAT3216IJS-2.85-T1 3.0V SC70JW-8 3.3V SC70JW-8 AAT3216IJS-3.3-T1 3.5V SC70JW-8 AAT3216IJS-3.5-T1 KKXYY AAT3216IGV-2.5-T1 AAT3216IGV-2.7-T1 AAT3216IGV-3.0-T1 KGXYY AAT3216IJS-3.0-T1 Note: Sample stock is generally held on all part numbers listed in BOLD. Note 1: XYY = assembly and date code. 14 3216.2004.01.0.94 AAT3216 150mA MicroPower™ LDO with PowerOK Package Information SOT23-5 2.85 ± 0.15 1.90 BSC 10° ± 5° 0.40 ± 0.10 0.075 ± 0.075 0.15 ± 0.07 4° ± 4° 1.10 ± 0.20 0.60 REF 1.20 ± 0.25 2.80 ± 0.20 1.575 ± 0.125 0.95 BSC GAUGE PLANE 0.45 ± 0.15 0.60 REF 0.10 BSC SC70JW-8 2.20 ± 0.20 1.75 ± 0.10 0.50 BSC 0.50 BSC 0.50 BSC 0.225 ± 0.075 2.00 ± 0.20 0.100 7° ± 3° 0.45 ± 0.10 4° ± 4° 0.05 ± 0.05 0.15 ± 0.05 1.10 MAX 0.85 ± 0.15 0.048REF 2.10 ± 0.30 All dimensions in millimeters 3216.2004.01.0.94 15 AAT3216 150mA MicroPower™ LDO with PowerOK AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. AnalogicTech warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with AnalogicTech’s standard warranty. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed. Advanced Analogic Technologies, Inc. 830 E. Arques Avenue, Sunnyvale, CA 94085 Phone (408) 737-4600 Fax (408) 737-4611 16 3216.2004.01.0.94